Learning Resources LER 4403 User manual

LER 4403
Easi-Speak™
Sound Station
Please Read All Instructions Carefully Before Using
User Guide
Easi-Speak™Sound Station User Guide Easi-Speak™Sound Station User Guide Easi-Speak™Sound Station User Guide Easi-Speak™Sound Station User Guide
24 35
• Please retain these instructions for future reference
• Sound Station contains a rechargeable NiMH
battery pack
• Do not attempt to remove the battery
• The external charger must be regularly examined for
potential hazard, such as damage to the cable or cord,
plug, enclosure or other parts. If such damage occurs,
do not use the Sound Station until that damage has
been fixed properly
• Only charge rechargeable batteries under adult
supervision
• Do not short-circuit the supply terminals
• Do not allow your Sound Station to come into contact
with water or other liquids
• In the event of an electro-static discharge, your Sound
Station may malfunction. In this case, you may need to
turn it off to reset it
• Warranty is void if the case is opened for any reason
• The warranty does not cover any data loss from the
Easi-Speak™ unit nor any consequential loss of
information
Know Your Sound Station
FCC compliance
NOTE:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO
OR TV INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and
receiver
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician
for help
Using Your Sound Station
The Easi-Speak™ connects to the Sound Station via the
headphone output socket. With the USB cap in place,
turn the Easi-Speak™ until the headphone socket faces
the jack plug on the Sound Station and push it into
place. Turn the Sound Station on and press the
Easi-Speak™ play button, then adjust the Sound Station
volume control to the desired level. It may be necessary
to increase the Easi-Speak™ volume, before docking, to
achieve the best results (the volume controls are not
accessible once the Easi-Speak™ is docked).
Power LED
The power LED is illuminated whenever the Sound
Station is turned on. When not in use, turn your Sound
Station off by rotating the volume switch until you hear
a “click” and the red power light turns off.
Charging the Battery
Sound Station is supplied with a partially charged
battery and can be used immediately without charging
first. The battery can be charged by connecting the
external power supply to the power input.
• Even when the battery is fully discharged, Sound
Station will operate normally when the external
power supply is connected. The battery will also be
charging at this time.
Power LED
On/off volume
Stereo speakers
Jack plug – connects to headphone
socket on your Easi-Speak
Line-in socket
6 Headphone
sockets
D.C. socket for
external charger

Easi-Speak™Sound Station User Guide Easi-Speak™Sound Station User GuideEasi-Speak™Sound Station User Guide Easi-Speak™Sound Station User Guide
6 87 9
• A complete charge of a fully discharged battery will
take about 24 hours. The Sound Station is intended to
be permanently left on charge so that it is always
ready for use.
Technical specification
• Built-in 1300mAH NiMH battery
• Total Harmonic Distortion+Noise 0.3% (Typ)
• Six stereo 3.5 mm headphone sockets (green)
• One stereo 3.5 mm line-in socket (pink),
100mV RMS Max
• Battery life approx. 3 hours (depends on volume
setting and type of audio)
Troubleshooting
Sound Station is designed to work reliably and
predictably in all normal conditions. However, it is
possible that problems may occur. Please check the
following before contacting technical support:
Support & Warranty
This product is provided with a one-year warranty for
problems found during normal usage. Mistreating the
Sound Station or opening the unit will invalidate this
warranty. Any data stored on the Easi-Speak™ and any
consequential loss is not covered by this warranty. The
battery is not user replaceable.
All out-of-warranty repairs will be subject to a
replacement fee.
Please visit www.LearningResources.com for the latest
product information and technical support.
Easi-Speak™ is a registered trademark of TTS Group Ltd.
Problem Power LED appears dim
Solution Battery is low. Charge the battery. Sound
Station can be used while charging
Problem Power LED doesn’t come on
Solution Battery completely flat; recharge
Problem Sound is too quiet
Solution The Easi-Speak™ recording is very quiet.
Increase the Easi-Speak™ volume setting
before docking
Problem Sound is distorted
Solution Reduce the Sound Station volume until the
sound is free from distortion. © Learning Resources, Inc., Vernon Hills, IL (U.S.A.)
Please retain our address for future reference.
Made in China. LRM4403-GUD
Fabriqué en Chine. Informations à conserver.
Made in China. Bitte bewahren Sie unsere
Adresse für spätere
Nachfragen auf.
Hecho en China. Conservar estos datos.
Visit our website to write a product review
or to nd a store near you.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
Warning: Changes or modifications to this unit not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.