LeCroy GP-EXT User manual

Accessory
GP-EXT
EXTERNAL USB PRINTER
User's Manual

WaveSurfer is a trademark of LeCroy Corporation.
Windows is a registered trademark or a trademark of Microsoft
Corporation in the United States and other countries.

EXTERNAL USB PRINTER User's Manual
Foreword
Thank you for purchasing LeCroy's EXTERNAL USB PRINTER
(hereafter referred to as "EXTERNAL USB PRINTER" or
"printer".)
Before using this printer, please read this manual thoroughly to gain
a good understanding of it. After reading, please keep the manual in
a safe place.
This manual describes notes on use and basic usage of the
EXTERNAL USB PRINTER.
Notes
Parts of the contents of this manual may be modified without prior
notice because of improvements in performance and functions.
Reproduction or reprinting of the contents of this manual without
prior permission from LeCroy is prohibited.
If you have questions about this printer, please contact LeCroy
Corporation. (Refer to the contact address given at the end of this
manual.)
Revision History
December 2004 : 1st edition
February 2005 : 2nd edition
April 2005 : 3rd edition
i
KML049431 A116-711101(B)

WaveSurfer Accessory
Checking the Packing Content
On delivery of the printer, check each item. If any of the items are
missing or there is any damage, immediately contact LeCroy or the sales
office in charge.
[Items to be present]
•Printer main unit (EXTERNAL USB PRINTER) ........................1
Accessories
•DC cable.......................................................................................1
•USB cable.....................................................................................1
•Mount...........................................................................................1
•Mount mounting screw.................................................................1
•Thermal paper roll for printer*.....................................................1
•User's manual ...............................................................................1
* Thermal paper rolls for the printer are available at LeCroy Corporation
or local sales dealer. Please contact LeCroy Corporation or local
sales dealer when ordering thermal paper rolls.
Sending The Printer Back for Repairs
If the printer is inoperable, send it back to LeCroy Corporation. (Refer to
the contact address given at the end of this manual.) We will repair it
without charge as long as it is under warranty.
When sending back the printer, explicitly describe the following:
product name, serial number, description of the trouble,
name/post/phone number of the contact person.
ii

Table of Contents
Safety Requirements........................................................................1
Product Disposal and Recycling......................................................3
Overview..........................................................................................4
Configuration ...................................................................................4
Units and Devices............................................................................5
(a) Printer.........................................................................................5
(b) DC Cable....................................................................................6
(c) USB Cable..................................................................................6
(d) Mount .........................................................................................7
Operating Procedures......................................................................8
(a) Attaching the Mounting Bracket to the Printer ............................8
(b) Mounting the Printer and Mounting Bracket onto the Rear of the
WaveSurfer.................................................................................9
(c) Connecting the DC Cable......................................................... 11
(d) Connecting the USB Cable.......................................................12
(e) Loading the Printer Paper.........................................................13
(f) Add a printer.............................................................................15
(g) Starting the Test Print................................................................18
(h) Starting the Print-out.................................................................19
(i) Turning OFF the Printer............................................................20
Indicators.......................................................................................21
Specifications.................................................................................22
(a) Product Specifications..............................................................22
(b) Certifications.............................................................................24

WaveSurfer Accessory
Safety Requirements
This section contains information and cautions that must be
observed to keep the External USB Printer operating in a correct
and safe condition. You are required to follow generally accepted
safety procedures in addition to the safety precautions specified in
this section.
Safety Symbols
The following symbols may appear on the product and they alert
you to important safety considerations.
This symbol is used where caution is required. Refer to the
accompanying information or documents in order to protect
against personal injury or damage to the instrument.
The CAUTION sign indicates a potential hazard. It calls
attention to a procedure, practice or condition which,
if not followed, could possibly cause damage to equipment.
IfaCAUTIONisindicated, do not proceed until its
CAUTION
conditions are fully understood and met.
Before using this product, ensure that its operating environment will
be maintained within these parameters:
Temperature: 0 to 40 oC
Humidity: 30%RH to 80%RH (non-condensing)
1

EXTERNAL USB PRINTER User's Manual
CAUTION
To avoid personal injury or damage to the External USB Printer or
the WaveSurfer oscilloscope connected to it, review and comply
with the following safety precautions.
•Use only as intended.
The External USB Printer is intended to be used only with the
LeCroy WaveSurfer series oscilloscopes to print a hard copy of
the screen image. Use of this product and/or the scope it is
connected to in a manner other than specified may impair the
protection mechanisms.
•Connect and disconnect properly.
Avoid damage to cables thru excessive bending.
Do not disconnect the DC cable and/or USB cable while printing.
Doing so may cause the product to malfunction or the data to be
corrupted.
•For indoor use only.
The printer is intended for indoor use and should be operated in a
clean, dry, environment.
•Do not operate with suspected failures.
Do not use the printer if any part is damaged. All maintenance
should be referred to qualified service personnel.
•Refer to assembly instructions in the manual before
mounting this product onto the rear of WaveSurfer
oscilloscope.
•Always use the attached DC cable.
If a cable other than that supplied is used, this may cause an
electric shock, a fire, or a malfunction.
•To ensure safety, turn OFF the Printer POWER, if it is not
used for an extended period of time.
2

WaveSurfer Accessory
•Do not touch thermal head soon after printing.
It may be hot.
Ensure Thermal Head is cold before replacing paper roll or
cleaning the head.
•Keep product surfaces clean and dry.
CLEANING
The outside of the printer hardware should be cleaned with a soft
cloth dampened with either deionized / distilled water or isopropyl
alcohol. Allow the surface to dry completely before returning the
instrument to service.
USE AND MAINTENANCE
The printer is a high quality, precision instrument. To maintain
accuracy, mechanical shock should be avoided, as well as damage
to the cables through excessive bending. All maintenance and
component replacement should be referred to qualified personnel.
Product Disposal and Recycling
This electronic product is subject to disposal and
recycling regulations that vary by country and region.
Many countries prohibit the disposal of waste electronic
equipment in standard waste receptacles.
For more information about proper disposal and
recycling of your LeCroy product, please visit
www.lecroy.com/recycle.
3

EXTERNAL USB PRINTER User's Manual
Overview
This printer is a thermal line dot printer specially designed for the
WaveSurfer-series.
The printer prints a hard copy of the screen of the WaveSurfer .
Power is supplied to this printer through the DC output of the
WaveSurfer. The printer is connected to the USB connector of the
WaveSurfer.
This printer can also be operated with the printer mounted on the
rear of the WaveSurfer. This instruction manual describes how to
mount the printer on the WaveSurfer, how to connect the printer to
the WaveSurfer, and how to operate the printer.
Configuration
This printer can be operated mounted on rear of the WaveSurfer or
unmounted. Reference Figure 1 for details on mounting. In either
case, the DC cable is connected to the DC-OUT connector of the
WaveSurfer to input the power to the DC INPUT connector of this
printer. Figure 1 shows the printer connected to the WaveSurfer
with the USB cable.
DC cable
USB cable
Printer
DC-OUT
DC INPUT
Rear of WaveSurfer
main unit
Figure 1 Printer Is Mounted on the Rear of the WaveSurfer
4

WaveSurfer Accessory
Units and Devices
(a) Printer
Figure 2 shows the outside view and dimensions of the printer.
DC INPUT connector USB connector
Insert nut
4-M3 (Screw depth: 4 mm)
Label
Bottom surface
Figure 2 Outside View and Dimensions of Printer
(in millimeters)
5