Lefroy Brooks CB-4626 User manual

INSTALLATION INSTRUCTIONS
CB-4626
RISER KIT WITH BLACK LEVER DIVERTER TO SUIT WALLMOUNTED EXPOSED
VALVES & BATH/ SHOWER VALVES
CW-4626
RISER KIT WITH WHITE LEVER DIVERTER TO SUIT WALLMOUNTED EXPOSED
VALVES & BATH/ SHOWER VALVES
CB-4626 CW-4626

2
Dimensions in Inches (& Millimetres)
Whilst every effort is made to ensure accuracy, design and dimensions are subject to
change without notice as part of the company’s product development process.
CB-4626
CW-4626
63 1/2"
(1611.5mm)
3/4"
(19mm)
5 3/16"
(131.5mm)
20
7/8"
(530mm)
3/4-14NPSM-2B
1/2-14NPSM-2A
Ø2 3/4"
(70mm)

3
Please note:
When there is a difference in water pressure between
hot and cold supplies to the mixing valve, the pressures
should by equalized by a plumber in accordance with
best practice and legislation.
What you need to know
Prior to beginning installation. turn off the cold and
hot water lines and open the old faucet to release
built-up pressure.
Overtightening nuts may cause damage.
Wrap all threaded connections with pipe tape
available at your local plumbing supply store.
Always wrap in a clockwise direction. The fittings
should be installed by a state-licenced plumber.
Adjustable Wrench
Groove Joint Pliers
Hacksaw
Phillips Screwdriver
Pipe Tape
Spatula
Spirit Level
Your new bathroom faucet is designed for years
of trouble-free performance.
Keep it looking new by cleaning it periodically with
a soft cloth. Avoid abrasive cleaners, wire wool and
harsh chemicals as these will dull the finish and
void your warranty.
If you are soldering during faucet installation,
remove cartridges, seats, gaskets and washers
prior to applying flame, otherwise you will void
the warranty.
Cover drain openings to avoid losing small parts.
When cutting or soldering pipe, use safety glasses
to protect your eyes.
Correct installation may vary depending on previous faucet installation. All necessary supplies required for
faucet installation are not included, but may be found where plumbing supplies are sold. It is suggested that
IAPMO and/or CSA approved plumbing supplies are used during installation.
Tools: Maintenance
SafetyTips
ThingsYouMayNeed
ImportantPoints
Standards
Standards
IAPMO/cUPC Listed
Meets A112.18.1
Please note :
Final achievable flow rate is dependent on the outlets fitted, see relevant outlets (spouts, roses, sprays) for fully
assembled product flow rate.

4
Steps 1-2
InstallationProcedure
Lefroy Brooks always recommends that plumbing products be installed by a licensed professional.
Shut off main water supply before installation.
1 2
1Fix riser kit with shower cradle of choice
(model shown is for example only) by
fixing the set screw. 2Assemble connecting tube with riser
bracket. Put the compression olive into
the riser bracket and then fix the shower
arm with the riser bracket. Tighten the
nut by wrench in order to fix the shower
arm with the bracket.
Product shown
as example only

5
Steps 3
InstallationProcedure
Lefroy Brooks always recommends that plumbing products be installed by a licensed professional.
Shut off main water supply before installation.
3
3Put the compression olive into the riser bracket and then fix the riser with the bracket. Put
the compression olive into the diverter body and then fix the riser with the diverter body.
Tighten the nut by wrench in order to fix the riser with the bracket and with the diverter
body.

6
Steps 4-5
InstallationProcedure
Lefroy Brooks always recommends that plumbing products be installed by a licensed professional.
Shut off main water supply before installation.
Fix riser kit to the faucet of choice (model
shown is for example only). Then fix the
riser kit with the wall bracket by tightening
the set screw. Finally fix the wall bracket to
the wall where (is) appropriate, with
anchors and screws.
45
Connect the shower head of choice (model
shown is for example only) with shower arm.
Connect the flexible hose with hand shower
of choice (model shown is for example only)
with diverter body.
4 5
Product shown
as example only
Product shown
as example only
Product shown
as example only

7
Exploded View
PartsList
CB-4626
CW-4626
1 Oil seal (010077)
2 Nut (009078)
3 Riser kit (064044)
4 Body (066014)
5 Diverter Cartridge (507775N)
6 Nut (009341)
7 Adaptor (067580)
8 Handle cap (109377)
9 Slot Cap (008247)
10 Screw (008245)
11 Lever seat (205461)
12 Rod (017094)
13 Lever (108924)
14 Lever cap (109376)
15 Riser kit (051458)
16 Nut (009078-T)
17 Compression olive (126135)
18 Hex socket set screw (008706)
19 Wall bracket (120289)
20 Plastic anchor (291000)
21 Screw (008003)
22 Connecting tube (017981)
23 Adaptor (077094)
24 Shower arm (035544)
25 Allen key (031000)
3
22
19
24
16
15
23
17
21
4
5
6
7
11
13
14
12
8
9
2
1
10
25
18
20

For additional assistance or service call
718-302-5292
9am to 5pm EST Monday to Friday
LEFROY BROOKS INC, 1828 TROUTMAN STREET, RIDGEWOOD, NY, 11385
TELEPHONE: [phone]. FAX: [phone]
The use of trademarks, product design and artwork is subject to licence or agreement with LBIP Ltd. The design
registrations, trademark registrations and copyrights are protected by law and the use or reproduction outside the terms of an agreement is prohibited.
The right to modify designs and dimensions is reserved. Christo Lefroy Brooks is a member of ACID (Anti Copying in Design).
© LBIP LTD 2012
www.lefroybrooks.com