Legend LPRVC User manual

CONTENTS
CONTENTS
•Safety Instructions 1
•Features 2
•Appearance 4
•Remote Control Unit 7
•How to Fix the Hard Disk Drive on the Receiver 12
•How to Format the Hard Disk Drive 14
•Receiver Connections 15
•Quick Setup Guide 17
•Search Channels 18
•Menu Map 22
•Menu Guide 23
•Channel List 36
•PVR 39
•Photo Album 56
•MP3 62
•Troubleshooting 69
•Specifications 70
Trade Mark of the DVB Digital Video Broadcasting Project

SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
Failing to heed the instructions provided on this page could result in serious damage
to your health or damage equipment or other such property.
WARNING
WARNING
!
!
• Always follow these instructions to avoid the risk of injury to yourself or damage to your
equipment.
• Unplug the power cord from the AC power outlet before cleaning. Use only a damp
cloth for cleaning the exterior of the receiver.
• Do not use accessories or attachments not recommended by the manufacturer, as they may
damage the equipment and said damage is not covered by the warranty.
• Do not operate the receiver in high-humidity areas, or expose it to water or moisture.
• Do not place the receiver on an unstable cart, stand, tripod, bracket, or table.
The receiver may fall, causing serious personal injury and damage to the receiver.
• Do not block or cover slots and openings in the receiver. These are provided for ventilation
and protection from overheating. Never place the receiver near or over a radiator or heat
register. Do not place the receiver in an enclosure such as a cabinet without proper
ventilation.
• Do not stack the receiver on top of or below other electronic devices. They should be at least
10 cm apart.
• Operate the receiver using only the type of power source indicated on the marking label.
Unplug the receiver power cord by gripping the plug, not the cord.
• Route power supply cords so that they will not be pinched by items placed on or against
them. Connect the power cord in the power outlets securely. Unplug the cord by grasping the
plug, not the cord.
• Use an outlet that contains surge suppression or ground fault protection. For added protection
during a lightning storm, or when the receiver is left unattended and unused for long periods
of time, unplug it from the wall outlet and disconnect the lines between the receiver and the
antenna.
• Do not attempt to service the receiver yourself, as opening or removing covers may expose
you to dangerous voltage, and will void the warranty. Refer all servicing to authorized
service personnel.
• Unplug the receiver from the wall outlet carefully and refer servicing to authorized service
personnel whenever the following occurs:
The power cord is damaged;
Liquid has been spilled, or objects have fallen into the receiver;
The receiver has been exposed to rain or water;
The receiver has been dropped or the chassis has been damaged;
The receiver exhibits a distinct change in performance.
1

FEATURES
FEATURES
Set
Set - -top box Part top box Part
• MPEG-II Video(MP@ML)
• MPEG-I Audio Layer 1, Layer 2
• MPEG-II Digital & Fully DVB Compliant
• LD Quality Video, CD Quality Audio
• European DVB-T standard
• Twin Tuner : one channel watching while one channel recording
• On-Screen Graphics menu with 256 Colors Full-Resolution
• User friendly OSG menu with full function
• Plug & Play Installation
• 4-digit 7-segment LED on the front panel displays channel information
• Displays local time on front panel, when it is on stand-by mode
• RS-232C port for additional information service and update of the receiver control software
• 64-Steps Volume control
• Favorite channel function
• IR remote control
• Last channel memory function
• Variable aspect ratio
• Maturity Rating control / Installation lock / Receiver lock
• EPG for on screen channel information
• Teletext supported by OSD & TV set
• Subtitle supported
• Total 2,000 channels programmable
• Dolby AC3 digital audio bitstream out supported through S/PDIF output (Coaxial/ Optical)
2

FEATURES
FEATURES
PVR Part
PVR Part
• PVR ready – Recommend 40/80/120G Hard Disk Drive named by Seagate, Maxtor, WDC
• Instant recording, Reserved recording Function
• PVR function with variety trick mode : FF, REW, Slow, Frame by Frame, Repeat, Jump, Index
• Time shifting function (PAUSE function for live signal)
• Random Access function while playback or time shifting
• Last play Function
• Play function while recording
• Permanent storing function of the time shifted files
• Time-shifting and Recording simultaneously.
• File management (Rename, Delete, Lock, Sort)
• MP3 function/ Photo Album.
Accessories
1. Remote Control Unit
2. Batteries
3. USB Cable
4. Loopthrough Cable
5. User Manual
3

APPEARANCE
APPEARANCE
Front View
1. On/ Stand-By
: Switch the receiver to On or Stand-by.
2. EPG
: Go to the EPG menu.
3. MENU
: Get access to the installation menu..
4. OK
: Give a confirmation or selection.
5. Left/ Right or Volume Up/Down
: Navigate Left/ Right through the selectable options or Volume Up/ Down.
6. Up/ Down or Channel Up/ Down
: Navigate Up/ Down through the selectable options or Channel Up/ Down.
1 2 3 4 5 6
4

APPEARANCE
APPEARANCE
RearView
1 2 3 4 5 6 7 8 9 10 11 12 13
1. ANT IN (TUNER 1)
: Connect to a terrestrial antenna to receive the digital broadcasts.
In case of the loopthrough connection between the two tuners;
Tuner 1 should be the master tuner to receive the signal from the antenna.
2. ANT IN (TUNER 2)
: Use for the Loop-through cable.
3. TV OUT
: Use for the Loop-through cable.
4. VCR SCART
: Connect to a connector of the VCR through out the fully-featured SCART cable.
5. TV SCART
: Connect this to a connector of the TV through out the fully-featured SCART cable.
6. AUDIO RCA
: Connect to a Left/right stereo output sockets for television.
5

APPEARANCE
APPEARANCE
RearView
1 2 3 4 5 6 7 8 9 10 11 12 13
7. VIDEO RCA
: Connect to a video signal output socket for television or AV receiver.
8. Component VIDEO OUT
: Connect to the component video sockets for television.
9. S-VIDEO
:Connects to a video signal output socket for Super-Video interface.
10. AUDIO RCA
: Connect to a Left/right stereo output sockets for the hi-fi system.
11. S/PDIF
: Connect to an audio output socket for Dolby digital audio signal for digital multi-channel
amplifier.his to Dolby Digital compatible audio equipment through coaxial S/PDIF cable.
12. SERIAL PORT
: Connect to a serial communication port of a PC for software upgrade (if required).
13. USB PORT
: Connect this to the USB port of a PC for Music and Software download.
6

REMOTE CONTROL UNIT
REMOTE CONTROL UNIT
I. TV MODE
I. TV MODE - -1 1
ON/STAND-BY MUTE
Switches the sound
ON/OFF.
7
.
NUMBER/
ALPHABET
Direct choice of TV /
Radio channel and input
a character by
alphabetical keys.
EXIT
Returns to the current
channel watching at any
time or exit out of the
submenu
OK/ CH LIST
It is used to select an
item in the menu.
Displays the channel
list on live signal
status.
RECALL
Return to the previously
viewed channel.
MENU
Displays the main
menu or return to
the previous menu.
TV / RADIO
Switches between
TV and Radio mode. INFORMATION
Press Once: Information
Banner
Press Twice: More
information on the current
and next program.

REMOTE CONTROL UNIT
REMOTE CONTROL UNIT
I. TV MODE
I. TV MODE - -2 2
ASPECT RATIO
Choose the Aspect
Ratio for the TV
screen.
ALT AUDIO
Select the audio
language
SLEEP TIMER
Set the sleep timer between
15min and 180min with
15min interval.
PAGE UP/ DOWN
It is used to move
up/down a page in a
list.
TELETEXT
Shows a teletext.
SUBTITLE
Shows Subtitle menu to
select the subtitle
language.
VOL
Adjusting Volume or
Move the Cursor Left/
Right. CH
Switching Channels or
Move the Cursor Up/
down.
EPG
Opens information on
program.
FAV
Move to the FAV
channel list.
GROUP (blue)
Move to the Group
mode in the channel list.
8

REMOTE CONTROL UNIT
REMOTE CONTROL UNIT
II. PVR MODE
II. PVR MODE
9
STOP
Return to the live
signal.
PVR
Move to the PVR list. Use
RED button to switch the
satus of the PVR list (Photo
Album, MP3 list, Saved
Programs).
RECORD
Enable the
recording to start.
REPEAT
Repeat the selected
file.
MARKER LIST
Shows the Index List
in a play mode.
REPEAT A-B
Repeat the selected
selection of the recorded
file between A and B.
MARKER
Use for the marker
function in a
recording or replaying
mode.
RECORDING PAUSE
Stop the recording
temporarily in a play-
back mode.
INFO/ HELP MENU
- Press Once : Display
the information banner.
- Press Twice : Display
the Help menu.
PLAY
Start to play a
recorded file.
1. TIME SHIFT
Make the time shifting
record to start.
2. PAUSE
Make the picture freeze
temporarily in a play
mode.
SLOW FORWARD
SLOW REVERSE
Enable a recorded file to
play with slow motion.
FAST FORWARD
FAST REVERSE
2 - 8 skip rate.
JUMP FORWARD
JUMP REVERSE
Short press: Jump 15
secs forward or reverse
to replay.
Long Press: Move to
desired location.

REMOTE CONTROL UNIT
REMOTE CONTROL UNIT
III. PHOTO ALBUM
III. PHOTO ALBUM
PVR
Move to the PVR list.
Use RED button to
switch the satus of the
PVR list (Photo
Album, MP3 list,
Saved Programs).
OK/CH LIST
Display the Photo
Album list when the
selected photo is
displayed. Show the
selected photo in the
Photo Album list.
INFO/ HELP MENU
- Press Once : Display
the information banner.
- Press Twice : Display
the Help menu.
DIRECTION
Use for the direction
key (Left/Right/Up/
Down) in Zoom In
mode. PLAY
Start the Slide Show
when the photo is
displayed.
STOP
Return to the live signal.
PAUSE
Stop Slide Show.
ZOOM IN/ OUT
Make the current photo
zoom in/ out. PREVIOUS
NEXT
Show the previous
photo or next photo.
10

REMOTE CONTROL UNIT
REMOTE CONTROL UNIT
IV. MP3 MODE
IV. MP3 MODE
PVR
Move to the PVR list.
Use RED button to
switch the satus of the
PVR list (Photo
Album, MP3 list,
Saved Programs).
REPEAT
Repeat the selected
file.
REPEAT A-B
Repeat the selected
selection of the music
file between A and B.
OK/CH LIST
Plays the selected
MP3 file from the
list. Displays the
MP3 list.
PLAY
Play the selected file. HELP MENU
Display the Help menu.
STOP
Return to the live signal. PAUSE
Makes the replay stop
temporarily.
FAST FORWARD/
REVERSE
Move to a selected
position forward/back.
JUMP FORWARD
JUMP REVERSE
Jump 10 secs. forward
or reverse to replay.
PREVIOUS/NEXT
Play the previous file
or next file.
11

HOW TO FIX THE HARD DISK
DRIVE ON THE RECEIVER
1. Set your HDD as a master. Please refer to
the instructions of setting method on HDD.
2. Tighten 4 screws combined with spacer
and cushion on the bottom of the HDD
bracket.
Connection Port
Screw
Spacer
Cushion
Tighten 4 screws.
12
34
3. Make sure that the HDD location on the
bracket is as right picture.
4. Connect the cable on the Main PCB.
12

HOW TO FIX THE HARD DISK
DRIVE ON THE RECEIVER
5. Tighten 4 screws to connect the HDD
bracket with the bottom chassis.
6. Connect the cable from Main PCB to the
HDD. And Connect the cable from SMPS to
the HDD.
This PVR ready receiver needs careful attention to the following cautions.
• Recommended to use Hard disk Drive (80/120G) by Hitachi.
•Set the Hard Disk Drive as a Master, when you connect the HDD to the receiver.
•Before use the new HDD initially, you should format the HDD first. In case of that you
format the HDD in the menu of the receiver, it may occur to lose any data in the HDD.
•The HDD is not in a good performance for use, the PVR function of the receiver may not
operate properly.
• Pay attention not to make any electric interference between this receiver and other appliances
such as PC.
• All management for the warranty or the upgrade of the HDD shall be treated by the dealer from
whom you purchased.
13

HOW TO FORMAT
THE HARD DISK DRIVE
1. Press the OK key on [PVR Setup].
2. Press the OK key on [HDD Format].
3. Select [ON] on [HDD Format].
If you want to delete all files of PVR/ MP3/
Photo Album, select [ON] on a each parameter.
Press the OK key on [Start].
4. Select [Yes] to confirm the HDD formation.
14

RECEIVER CONNECTIONS
RECEIVER CONNECTIONS
◆It is possible to make different connections with the use of the SCART and RCA
cables. Before making a connections with the cables, you should connect the ANT IN
connector of the receiver to the cables from the terrestrial antenna.
◆DO NOT PLUG the receiver into the Main Power Outlet, until you complete all
connections to the receiver.
Connection 2 – VCR SCART
Connection 3 - RCA
LOOPTHROUGH
15
Connection 1
- TV SCART
Connection 6 – Hifi-system
Connection 7 - USB/ SERIAL
Off Air ANT
Connection 4
-S-VIDEO
Connection 5
- Component Video

RECEIVER CONNECTIONS
RECEIVER CONNECTIONS
1.Connectingthetelevision
- Plug the Euro-AV (Scart) cable supplied into the TV socket on the receiver and the corresponding
Euro-AV socket (e.g. EURO-AV, SCART) on the television.
2.ConnectingtheVCR
- Plug a standard Euro-AV (Scart) cable into the VCR socket on the appliance and the Euro-AV
socket (e.g. EURO-AV, LINE IN/OUT, EXT.1) on the video recorder.
3.ConnectinganAVreceiver
- Plug a standard cinch cable into the VIDEO and L R AUDIO sockets (left/right) on the receiver
and the corresponding input sockets on the AV receiver.
4.ConnectingaSuper-Videointerface
- Plug a Super-Video cable into the S-Video socket on the receiver and the corresponding S-Video
socket on the television.
5.ConnectingaComponentVideooftelevision
- Plug a Component Video cables into the component video sockets on the receiver and the
corresponding component video sockets on the television.
6.Connectingadigitalmulti-channelamplifier
- Plug a standard S/PDIF cable into the S/PDIF socket (Coaxial / Optical) on the receiver and the
corresponding socket on the digital multi-channel amplifier.
- Make sure the S/PDIF type which your amplifier supports between the Coaxial type and the
Optical type before connecting the S/PDIF cable.
7.Connectingadatadownloadport(USB/SERIAL)
- Plug a data download cable into the data download port (USB / SERIAL) on the receiver and the
corresponding download port on the PC.
16

QUICK SETUP GUIDE
QUICK SETUP GUIDE
1. Connect your television antenna to the TUNER 1 ANT IN input
on the set top box.
2. Using the small Loopthrough cable provided, connect the
TUNER 1 (TV OUT) to the TUNER2 (ANT IN).
3. Connect your set top box to your television using the RCA
plugs provided (Yellow, Red, White).
4. Power on your set top box .
5. Select your Language settings & press the EXIT key.
6. Select the aspect ratio corresponding to your television
(widescreen 16:9 or 4:3) & press the EXIT key.
7. Select your local time & press the EXIT key.
8. Make sure the search type is set to AUTO, scroll down to
START.
9. Search & press the OK key . (Auto Search may take several
minutes).
10. When the Auto Search is completed, press the OK key when
prompted, then press the EXIT key to start viewing broadcasts.
17

SEARCH CHANNELS
SEARCH CHANNELS
When you start the receiver, it will switch to a guided introduction. Go through this
introduction for the receiver according to the instructions supplied below.
•Move the menu’s cursor using the arrow buttons (◀, ▶, ▲and ▼).
•Select or confirm the changes by pressing OK.
•Press MENU to go to the next setup menu.
LanguageSettings
You can select the desired language for the Audio,
Closed Caption and Teletext language.
1. Press the ◀,▶keys to move to the desired language
and press OK or use OK to open the language bar and
use OK to select the language you would like.
2.Use the ▲,▼keys to move to the next language
settings.
Main Audio
It is used to select the main audio language for
channels that have multiple audio languages.
Second Audio
It is used to select the second audio language for
channels that have multiple audio languages. The
second audio language is automatically selected by the
receiver if the selected main audio language is not
available.
Main Closed Caption
It is used to select the main closed caption language for
channels that have multiple closed caption languages.
Second Subtitle
It is used to select the second closed caption language
for channels that have multiple closed caption
languages. The second closed caption language is
automatically selected by the receiver if the selected
main closed caption language is not available.
Teletext
It is used to select the OSG language of the teletext.
18