Lehigh H10123 User manual

H10123 Wireless DMX512 Receiver Installation Guide F479
F479 R1.01 Lehigh Electric Products Co. 6265 Hamilton Blvd.., Allentown, Pa. 18106 Tel: [phone] www.lehighdim.com
H10123 Wireless DMX Receiver
Lehigh offers DMX512 (ANSI E1.11) and RDM (ANSI E1.20) signal distribution equipment for theatrical, architectural, and architainment applications.
The H10123 wireless DMX512/RDM receiver is provided in a 1-gang enclosure with a 5-pin XLR connector. LED indicators are provided for DMX signal and
radio link status as well as signal quality. A button is provided to link or unlink the receiver from a transmitter. The unit requires an external AC/DC power
supply which is provided and can be pipe, surface, or flush mounted.
DMX Out Port:
RS485 slew-rated transceiver, true fail-safe featured
± 80V fault protection, D+/D-
120 ohm termination and bias resistors
± 12kV ESD protection (Human Body Model)
Short circuit protection with thermal shutdown
Installation
Pipe Mount
Mount on the top of the pipe using the supplied U-bolt.
Surface Mount
If the unit must be surface mounted, remove the pipe mount bracket and unscrew the faceplate/electronics from the supplied gang box. Mount the gang box
using the mounting holes at the rear of the box. Re-install the faceplate/electronics.
Flush Mount
If the unit must be flush mounted, remove the pipe mount bracket and unscrew the faceplate/electronics from the supplied gang box. If the supplied gang
box cannot be flush mounted, use a standard 1-gang box with a minimum depth of 2 ½ inches. Re-install the faceplate/electronics using supplied machine
screws.
W
i
r
e
l
e
s
s
D
M
X
R
e
c
e
i
v
e
r
Receives CRMX, W-DMX G3,G4, G4S,
and G5
Supports ANSI E1.11 - DMX512-A and
ANSI E1.20 –RDM
OA Firmware Updates
Theatrical or Architectural DMX512
Distribution

H10123 Wireless DMX512 Receiver Installation Guide F479
F479 R1.01 Lehigh Electric Products Co. 6265 Hamilton Blvd.., Allentown, Pa. 18106 Tel: [phone] www.lehighdim.com
Wireless Setup
Linking Receivers to a Transmitter
On the transmitter, press the link button briefly. All unlinked receivers within range will be linked to the transmitter.
Unlink Receiver(s)
On the transmitter, press and hold the link button for more than 3s to unlink any linked receivers. Note, on a receiver holding the link button for more than
3s will cause that receiver to unlink.
Status LED (Receiver)
Constant off: Not linked to any transmitter.
Flashing: off 100 ms / on 100 ms: linked to a transmitter, but no active radio link.
Flashing: off 100 ms / on 900 ms: Active radio link, no DMX present.
Constant on: Active radio link, DMX data present
Signal LED (Receiver)
In receiver mode the RGB LED indicates the signal quality of the received signal.
Color
Meaning
>80%
60-80%
30-60%
<30%
WARRANTY
Subject to the terms of this paragraph, the supplier warrants its title to the products sold by it and warrants to the Purchaser that its products are free of defects
in workmanship or material and are in conformity with applicable specifications and descriptions of the supplier. No claim shall be maintained hereunder
unless the facts giving rise to it are discovered within 16 months from the date of shipment from the factory, or 12 months after initial energization of said
equipment, with the one expiring first given precedence, and written notice thereof given to the supplier within 30 days of discovery. The sole and exclusive
liability of the supplier, for Breach of Warranty shall be, at its option, to replace or repair the product or part concerned F.O.B. its factory or such place as it
may designate. The warranties stated in this paragraph are exclusive of all other warranties, written or oral, statutory, expressed or implied, none of which shall
apply to the sale of the suppliers products hereunder.