Lena Lighting WSEL437 User manual

Remotefordimmablesensors
withmemoryfunction
WSEL437 (HD03R)
ON/OFF
1."ON/OFF" keyonlyfunctionsasaswitch ofthelight.
2.Ifpressthisbuttontoturnoffthelampbeforeit'sshort-circuited,thelampwillremainoffafterpower-on again.
AutoMode
Press “Auto Mode” button, the sensor starts to workandallsettingsremainthesamebeforethelightgetsswitchedon/off.
Reset
1、Press"Reset"button,changebrightness tomaxlevel.
2、Press “Reset” button, products with DIP switch will be controlled by DIP switches; otherwiseallthesettingwillbejust
initial,thatis100%detectionrange,holdtime5S,nostand-bytimeanddaylightthresholddisabled.
Flickafterpressanybutton
Flickonlyafterpress"Apply"button
+/-
1.Toadjustbrightness10-100% inon/offmode.
2.Toadjusthighestbrightenss60-100%insensormode.
Start
Press"Start" tocustomizescene,userscanchangedetectionrange,daylightthreshold,holdtime,standbydimmingleveland
standby period.
Memory
1.Press"Memory"tosave allthesettings.
2.Thesettingsremainedasthelasttimeifnotgetresettedvalues.
Apply
1.Press"Apply"todeliverthesavedsetting.
2. Press "Apply" without “memory”will make all the setting one-timeoperation.
3.Settingsshouldbedonewithin30S,otherwiseitexitsmemorymode.
Detectionarea(Presstodefinedetectionarea100%/75%/50%/25%.)
Holdtime(Presstodefineholdtime5s/30s/1min/3min/5min/10min/20min/30min.)
Stand-bydimminglevel(Presstodefinestand-bydimminglevel10%/20%/30%/50%.)
Stand-byperiod(Presstodefinestand-byperiod 0s/10s/30s/1min/5min/10min/30min/+∞.)
Note: “0s” means no standby period; “+∞” means unlimited standby period.
Daylightthreshold(Presstodefinedaylightlevel2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/Disable.)
Note:Disablemeanslightwillbeturnedononcesensordetectsmovement,regardlessoftheambientlux.
Test (2s)
The button “Test (2s)” is for testing purpose after commissioning.Pressing this button, the sensor goes to test mode
(holdtimeisonly2s)

HD03RInstruction
Memory&ApplyMode
1.Press"ON/OFFbutton"toturnonthelightoroff.
2.Toresettheparameters,Pleasefollowthestepsasbelow:
Step1-PressON,toturnonthelightifitwasoffatthestart.
Step2-Press"Start"to thewell-setting sensor.
Step3-Pressthe buttonofDetection range, Hold time,Stand-by dimming level,Stand-by period and Daylight threshold oneafter the
otherinsequence.
Step5–Press “Memory” to memorize the settings.
Note:Theintervalofeachparametersettingshallbecontrolledwithin30s.
3.Toprogrammeotherlightsinthearraythathavesimilarsensorstothesameprogramme.
Step1-Press"ON"tothesecondsensor
Step2-Press"Apply"
IsolatedSettingMode
1.Press"ON/OFFbutton"toturnonthelight oroff.Press"AutoMode",theremotewillactivatesettingsthatweresavedlastor
remainatthefactorydefaultsettings.
2.Toresettheparameters,Pleasefollowthestepsasbelow:
Step1-PressON,toturnonthelightifitwasoffatthestart.
Step2-Press any button of "Auto Mode", “Reset” , Test" and "Apply" to begin the sensor detection mode.
Step3-Pressthe buttonofDetection range, Hold time,Stand-by dimming level,Stand-by period and Daylight threshold oneafter the
otherinsequence.
Notes:
1.Settingswillbesavedautomatically andremainuntilyoupressresetagain.
2.Lightwillflickerwhensetting eachparameter.