LENCO SCDI-01 User manual

DATE : 15 / 06 / 11 , MODEL : SCDI-01 / LENCO , STCD108 DECK
ENGLISH FM/AM I/M , 230V , W/CDR-RW , W / AUX , iPOD DOCKING ,
W / O VIDEO & AUDIO OUT ,
SIZE : 525 x 297 MM
Stereo CD Radio PlayerStereo CD Radio Player
WITH i-Pod Docking Station
INSTRUCTION MANUAL
SCDI-01
For information and support, www.lenco.eu
SCDI-01 LENCO ENGLISH IM NO RCA 1 1 15/6/2011 14:48:20

WARNING
CLASS 1 LASER PRODUCT
This product contains a low power laser device.
CLASS 1 LASER PRODUCT
APPAREIL Á LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM
PRECAUTIONS
Follow the advice below for safe and appropriate operations.
ON PLACEMENT
• Do not use the unit in places which are extremely hot, cold, dusty, or humid.
• Placetheunitonaatandevensurface.
• Donotrestricttheairowoftheunitbyplacingitinaplacewithpoorairow,bycoveringitwithacloth,orby
 placingitonacarpet.
ON SAFETY
• WhenconnectinganddisconnectingtheACcord,griptheplugandnotthecorditself.Pullingthecordmay
 damageitandcreatehazard.
• Whenyouarenotgoingtousetheunitforalongperiodoftime,disconnecttheACpowercord.
ON AC VOLTAGE
• Beforeuse,checkthattheratedvoltageofyourunitmatchesyourlocalvoltage.
ON CONDENSATION
• When left in a heated room where it is warm and damp, water droplets or condensation may form inside the
CD player.
• When there is condensation inside the unit, the unit may not function normally.
• Letitstandfor1to2hoursbeforeturningthepoweron,orgraduallyheattheroomupanddrytheunitbeforeuse.
• Ensureaminimumdistanceof5cmaroundtheapparatusforsufcientventilation.
• Ensurethattheventilationisnotimpededbycoveringtheventilationopeningswithitems,suchasnewspapers,
table-cloths, curtains, etc..
• Donotplacenakedamesources,suchaslightedcandlesontheapparatus.
• Take attention to the environmental aspects of battery disposal.
• Use the apparatus only in moderate climates (not in tropical climates).
• Donotexposetheapparatustodrippingorsplashing.
• Donotplaceobjectslledwithliquids,suchasvases,ontheapparatus.
Should any trouble occur, disconnect the AC power cord and refer servicing to qualied personnel.
ATTENTION : To reduce the risk
of electric shock, do not remove the
cover. There are no user serviceable
partsinsidetheunit.Referallservicing
toqualiedpersonnel.
The exclamation point within
thetriangleisawarningsign
alertingtheuserofimportant
instructions accompanying
the product.
The lightening flash
with arrowhead symbol
within the triangle is a
warning sign alerting
the user of "dangerous
voltage" inside the unit.
Warning: Do not touch the lens.
DO NOT THROW BATTERIES IN FIRE !
Incaseofmalfunctionduetoelectrostaticdischarge,theapparatushastoberesetbydisconnectingitfrommainssupply.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SCDI-01 LENCO ENGLISH IM NO RCA 2 2 15/6/2011 14:48:20

POWER / STANDBY BUTTON
CONTROLS
GB 1
REMOTE CONTROL UNIT
I - MENU BUTTON
PLAY/PAUSE
I - POD PLAY BUTTON
F - SKIP / I - POD BUTTON
FUNCTION BUTTON
ST / MONO
I-SELECT BUTTON
PEPEAT / P+ / I - UP BUTTON
STOP / I - POD STOP BUTTON
TIMER / EQ BUTTON
BAND/FOLDER BUTTON
PROGRAM / MEMORY/ CLK - ADJ BUTTON
RANDOM / P- / I - DOWN BUTTON
ID3 BUTTON
SNOOZE / SLEEP BUTTON
VOLUME + BUTTON
VOLUME - BUTTON
B - SKIP / I - POD BUTTON
MUTE BUTTON
1. VOLUME + / - BUTTON
2. FUNCTION BUTTON
3. HANDLE
4. RANDOM / P - BUTTON
5. REPEAT / P + BUTTON
6. PROGRAM / MEMORY / CLK - ADJ
BUTTON
7. SNOOZE / SLEEP BUTTON
8. CD DOOR
9. POWER / STANDBY BUTTON
10. OPEN / CLOSE BUTTON
11. PLAY / PAUSE BUTTON
12. STOP BUTTON
13. TIMER / EQ BUTTON
14. BAND / FOLDER BUTTON
15. F - SKIP BUTTON
B - SKIP BUTTON
16. SPEAKER
17. I - POD UNIVERSAL DOCK AND
CONNECTOR
18. SD / MMC
19. USB SLOT
20. CD DISPLAY
21. AC SOCKET
22. TELESCOPIC ANTENNA
23. AUX. IN JACK
24 PHONES JACK
25. REMOTE SENSOR
26. BATTERY COMPARTMENT
SCDI-01 LENCO ENGLISH IM NO RCA 3 3 15/6/2011 14:48:20

Tuning a RADIO Station
1. Press the FUNCTION button repeatedly
until “TUNER” is shown.
2. Press the BAND / FOLDER button to
 selectthedesiredfrequencyband(FMorAM).
3. Press the F - SKIP or B - SKIP
buttonasmanytimesasrequiredto
tune into the desired station.
4. Press and hold the F - SKIP or B - SKIP
button for more than 1 second ,
scanningstartsautomaticallyandthetunerwillstop
 attherstreceivablebroadcaststation.
5. Tostopautotuning,presstheF-SKIP
 orB-SKIPbuttonagain.
POWER SUPPLY
USING HOUSE CURRENT
Beforeuse,checkthattheratedvoltageofyourunitmatches
yourlocalvoltage.
Note:plugisusedasthedisconnectdevice.
the disconnect device shall remain readily operable.
USING BATTERIES
Disconnect the AC power cord from
the AC inlet of the unit. Battery power
is cut automatically by the cord while
it is connected.
Insert8UM-2(sizeC)batteries.
battery door
When the volume decrease,
or the sound distorts,
replace all of the batteries
with new ones.
To AC socket
To AC outlet
GB 2
ADJUSTING THE SOUND
Press volume +/- to adjust the volume level.
FOR PRIVATE LISTENING
Plug headphones (ø3.5 mm stereo mini-plug) into the
PHONES jack. When headphones are plugged in, the
speakers will automatically be disconnected.
VOLUME
PressthePOWER/STANDBYbuttontoturntheaudioon.Tochangetheaudiomodebetween,
CD , UDISK , SD/MMC , IPOD , AUX and TUNER, press the FUNCTION button while the power is on.
The audio mode will be displayed.
Power will be cut off automatically when the CD, MP3 and USB functions are in stop mode for
15 minutes.
TURN ON / OFF THE SYSTEM
Selecting FM Stereo/Mono mode
1. To select FM stereo/mono mode, press the STEREO/
MONO button on the remote control.
2. The “STEREO” icon will be on when the received
station is broadcasted
in Stereo.
3. To select mono mode, press STEREO / MONO button
 again.
4. The “STEREO” icon will never turn on in FM MONO
mode.
TUNER OPERATION
VOLUME
battery door
Insert3LR03(sizeAAA)batteries.
Back up Batteries for the clock
FUNCTION
BAND/FOLDER/
I-MENU
FUNCTION
SCDI-01 LENCO ENGLISH IM NO RCA 4 4 15/6/2011 14:48:21

1. Tune to a desired radio station.
2. PressthePROGRAM/MEMORY/CLK-ADJ.buttontoentertuningsavingmode.
The “MEMORY” icon will be on.
3. Programnumber“01”willbeashingonthelefthandside.
4. Within 10 seconds, press the RANDOM/P- or REPEAT/P+ button to select the
 desiredprogramnumber.
5. PressthePROGRAM/MEMORY/CLK-ADJ.buttontoconrm.
6. Ifthereisnobuttonpressedwithin10seconds,itwillexittuningsavemodeandthe
“MEMORY” icon will be off.
TO SKIP TO THE BEGINNING OF A TRACK
• Presseitheroneoftheskipbuttonsaccordingtothedesiredskipdirection.
• Play/back resumes from the selected track.
• Whenthebuttonispressedtwiceduringplayback,theprevioustrackwillstartagain.
• Whenthebuttonispressedonceduringplayback,thenexttrackwillbeplayed.
CD display MP3 display
WMA display USB display
RADIO MEMORY FUNCTION
COMPACT DISC PLAYBACK
1. Press the FUNCTION button
repeatedly until “CD” is
shown on display.
2. LifttheCDdoorup,bypressingattherightsideofthe
CD door.
3. Insert a disc with the label
 sidefacingup.
4. Close the CD door, the disc will rotate.
For CD : The total tracks of the disc will show on the
display.
For MP3/WMA/USB : The total tracks of the disc and
the total number of the folders will be shown on the
display.
CD display
GB 3
TO STOP PLAYBACK
Press the STOP button.
For CD : The total number of tracks and time will be shown.
For MP3 : The total number of tracks and folder will be shown.
For WMA : The total number of tracks and folder will be shown.
For USB : The total of tracks and folder will be shown.
For CD : Track number "001" & "CD" will be shown, the
 timeofthetrack"00:00"willash,duringnormal
compact disc playback.
For MP3 : Track number "001" & "MP3" will be shown,
  thetimeofthetrack"00:00"willash,during
MP3 playback.
For WMA : Track number "001" & "WMA" will be shown,
  thetimeofthetrack"00:00"willash,during
WMA playback.
For USB : Track number "001" & "USB" will be shown,
  thetimeofthetrack"00:00"willash,during
USB playback.
TO INTERRUPT PLAYBACK
Press the PLAY/PAUSE button. Press the button
againtoresumeplayback.
5. Afterdiscreadingisnished,thediscwillbeplayed
automatically. In stop mode, press the PLAY /
PAUSE button to play the track.
For CD : Track number "001" & "CD" & "00:00" will be
 shown,duringnormalcompactdiscplayback.
For MP3 : Track number "F01" & "MP3" & "00:00" will
  beshown,duringMP3playback.
For WMA : Track number "F01" & "WMA" & "00:00" will
  beshown,duringWMAplayback.
For USB : Track number "F01" & "USB" & "00:00" will
  beshown,duringUSBplayback.
CD display MP3 display
WMA display USB display
FUNCTION
FOR BETTER RECEPTION
FM AM
PROGRAM /
MEMORY /
CLK-ADJ.
F - SKIP
B - SKIP
SCDI-01 LENCO ENGLISH IM NO RCA 5 5 15/6/2011 14:48:21

GB 4
FOR NORMAL COMPACT DISC PLAYBACK
ModesequenceREPEAT>>REPEATALL>>CLEAR.
DuringRepeat1mode,
the display shows
DuringRepeat2mode,
the display shows
DuringRepeat3mode,
the display shows
REPEAT , REPEAT ALL , REPEAT A B , REPEAT FOLDER PLAYBACK
MP3/WMA/USB display
CD display
FOR MP3 / WMA / USB PLAYBACK
Mode sequence REPEAT >> REPEATALL >> REPEAT
FOLDER>>CLEAR.
DuringRepeat1mode,
the display shows
DuringRepeat2mode,
the display shows
DuringRepeat3mode,
the display shows
DuringRepeat4mode,
the display shows
Press the REPEAT / P + button during stop mode.
FOR MP3 / WMA / USB PLAYBACK
ModesequenceREPEAT>>AREPEAT>>
A-BREPEAT>>REPEATALL>>FOLDER.
DuringRepeat1mode,
the display shows
DuringRepeat2mode,
the display shows
DuringRepeat3mode,
the display shows
DuringRepeat4mode,
the display shows
DuringRepeat5mode,
the display shows
DuringRepeat6mode,
the display shows
FOR NORMAL COMPACT DISC PLAYBACK
ModesequenceREPEAT>>AREPEAT>>
A-BREPEAT>>REPEATALL.
DuringRepeat1mode,
the display shows
DuringRepeat2mode,
the display shows
DuringRepeat3mode,
the display shows
DuringRepeat4mode,
the display shows
DuringRepeat5mode,
the display shows
Press REPEAT / P + button during playback.
CD display
For CD : The total number of tracks and time will be shown.
For MP3/WMA/USB: The total number of tracks and folders will be shown.
For CD : The folder tracks number and time will be shown.
For MP3/WMA/USB: The folder tracks number and folder will be shown.
MP3/WMA/USB display
SEARCHING FOR A PASSAGE WITHIN A TRACK
• Keeptheorbuttonpressedduringplayback,andreleasethebuttonassoonasyou
 recognisethedesiredpassage.ThenthenormalCDplaybackwillresumefromthispoint.
PLAYING TRACKS IN RANDOM ORDER
1. If the RANDOM / P - button is pressed, the tracks on the discs are not playedRANDOM / P - button is pressed, the tracks on the discs are not playedis pressed, the tracks on the discs are not played
in consecutive order but in random order. The word RAND appears on the display to provide
a visual reminder that the RAND function has been activated.
2. Press the RANDOM / P - button to switch off the RAND function.RANDOM / P - button to switch off the RAND function.to switch off the RAND function.
Note on CD-R/RW discs
- Becauseofnon-standardizedformatdenition/
 productionofCD-R/RW,playbackqualityandperformancearenotguaranteed.
- ManufacturerisnotresponsiblefortheplayabilityofCD-R/RWduetorecordingconditions,
 suchasPCperformance,writingsoftware,mediaability,etc.
- Do not attach a seal or label to either side of the CD-R/RW disc. It may cause a malfunction.
- ItisrecommendedtorecordonlyaudiolesonCD-R/RWdiscsforeasyreading.
SCDI-01 LENCO ENGLISH IM NO RCA 6 6 15/6/2011 14:48:21

1. PresstheTIMER/EQbuttontoselectthe following EQ settings :thefollowingEQ settings :EQsettings:
 -FLAT->ROCK->JAZZ->CLASSIC->POP->FLAT.
will be shown on the display.
1. Insert USB / SD / MMC into the USB / SD / MMC input slots of the system.
2. Press the “FUNCTION” button to select USB / SD / MMC mode.
3. The unit will start to read the media and playback will start automatically.
note: The USB connector does not support connection with a USB extension cable and
 itisnotdesignedforcommunicationwithacomputerdirectly.
The manufacturer is not responsible for the playability of a USB / SD / MMC disk or MP3 player
 duetorecordingconditions,capacity,interfacecompatibility,etc.
Due to different formats, some USB / SD / MMCdisksorMP3playersmaytakelongertimetoberead.
USB / SD / MMC OPERATION
FUNCTION
PRESET EQ
TIMER / EQ
Muteon/offischangedcyclicallybypushingtheMUTEbutton.
The“mute”markisonduringmute.
Mutewillbecancelledwhenyoucarryoutthefollowingoperations.
a. PresstheMUTEbuttonagain.
b. The Volume is adjusted by the VOL +/- button.
MUTE ON/OFF
MUTE
FOR NORMAL COMPACT DISC PLAYBACK
Programmedplaybackenablestracksonadisctobeplayedinadesiredorder.Upto20trackscanbeprogrammed.
1. ProgrammodeworksinSTOPmodeonly.
2. Holdthe“PROGRAM/MEMORY/CLK-ADJ.”buttonfor2secondstoenterprogrammode.
 The“PROG”iconwillbeturnedon.“000P01”willbeshownwith“000”ashing.“000”
 representsthetracknumberand“P01”representstheprogramlocationnumber.
3. PresstheF-SKIPorB-SKIPbuttontoselecttherequiredtracknumber.
4. Pressthe“PROGRAM/MEMORY/CLK-ADJ.”buttontoconrmthetracknumber.Thedisplaywill 
 showthenextprogramnumber“000P02”.Thetracknumberwillbeashingagain,enterthedesiredtracknumber.
5. Repeatsteps3and4untilallthedesiredtrackshasbeenprogrammedoralltheprogrammemorieshavebeenused.
 ItwillloopbacktoP01afteralltheprogrammemorieshave
 beenused.Thesametracknumbercanbeprogrammedmorethanonce.
6. Press the PLAY / PAUSE button to start playback.
7. PresstheSTOPbuttontoclearalltheprogrammedtracks.
GB 5
FOR MP3/WMA/USB/SD PLAYBACK
Programmedplaybackenablestracksonadisctobeplayedinadesiredorder.Upto20trackscanbeprogrammed.
1. ProgrammodeworksinSTOPmodeonly.
2. HoldthePROGRAM/MEMORY/CLK-ADJ.buttonfor2secondstoenterprogrammode.The“PROG”iconwill
 beturnedon.“00000P01”willbeshownwith“00”ashing.“000”representsthetracknumberand
 “P:01”representstheprogramlocationnumber.
3. Press the F - SKIP or B - SKIP button to select the desired folder.
4. Press the PROGRAM / MEMORY / CLK - ADJ. button to enter selected folder number.
5. PresstheF-SKIPorB-SKIPbuttontoselecttherequiredtracknumber.
6. PressthePROGRAM/MEMORY/CLK-ADJ.buttontoconrmthetracknumber.
 Thedisplaywillshowthenextprogramnumber“000P02”.Thetracknumberwillbe
 ashingagain,enterthedesiredtracknumber.
7. Repeatsteps3and4untilallthedesiredtrackshavebeenprogrammedorallthe
 programmemorieshavebeenused.ItwillloopbacktoP01afteralltheprogram
 memorieshavebeenused.Thesametracknumbercanbeprogrammedmore
than once.
8. Press the PLAY / PAUSE button to start playback.
9. PresstheSTOPbuttontoclearalltheprogrammedtracks. MP3/WMA/USB display
PROGRAMMED CD / USB / SD / MMC OPERATION
CD display
PROGRAM /
MEMORY /
CLK-ADJ.
PROGRAM /
MEMORY /
CLK-ADJ.
SCDI-01 LENCO ENGLISH IM NO RCA 7 7 15/6/2011 14:48:21

- Press the ID3 button on the remote to enter ID3 setting mode and select " ID3 ON " or " ID3 OFF "PresstheID3buttonontheremotetoenterID3settingmodeandselect"ID3ON"or"ID3OFF"
- Songname,Singernameandalbumnamecanbedisplayedcyclically  
 duringplayingMP3.
- Title-songnameArtist-singernameAlbum-Albumname
FOLDER SELECTION
1. In STOP mode, press the BAND / FOLDER button to skip to the next folder.
2. This operation is valid for MP3 / WMA / USB media that has been placed into a
folder.
AUX. IN
An external (auxiliary) audio source (i.e., personal CD player
or MP3 player) can be connected to this unit and heard
throughthespeakers.
1) Plugoneendofthecable(notincluded)intotheAUXIN
socket on the unit.
2) PlugtheotherendofthecableintotheHeadphoneor
Line Out socket of the external source.
3) Press the FUNCTION button repeatedly until “AUX ”
is shown on the display.
ContinuetooperatetheCDorMP3playerasusual.Selectionswillbeheardthroughtheunit'sspeakers.
AUXIN
kHz
MHz
USB
SNOOZE
CARD
ALLB FOLDER INTRO RAND PROG
EQ RDS
STEREOMEMORY
BASS
MP3WMA
SLEEPTIMER
CD
1. If you want to fall asleep to music, press and hold
the SNOOZE / SLEEP button when the unit is on.
2. YoumayadjusttheradioorCDplayer'ssleepfunctiontoplayfrom10,20,
 30upto90minutesofmusicbeforeshuttingitselfoffautomatically.
00 = sleep timer off
TO SET SLEEP FUNCTION
10 20 30 40 50 60 70 80 90 00
GB 6
During the stop mode
1. PressingtheSNOOZE/ SLEEP button on the remote will turn off the system for 9 minutes.on the remote will turn off the system for 9 minutes.
2. Pls note that the SNOOZE / SLEEPbutton will only be functional during TIMER mode.button will only be functional during TIMER mode.willonlybefunctionalduringTIMERmode.
SNOOZE
FUNCTION
BAND / FOLDER
ID3
ID 3 DISPLAY
(Plugtheotherendintotheexternal
source such as an MP3 player.)
SLEEP
TIMER
1. PresstheSTANDBYbuttontogointostandbymode.
2. Pressandholdthe"TIMER/EQ"button,"TIMER"/thehourdigitswillash.
Press the skip buttons to set the hour.
 Pressthe"TIMER/EQ"buttontoconrm,theminutesdigitswillashandpress
 theskipbuttonstosettheminutes.Pressthe"TIMER/EQ"buttontoconrm.
3. TimerwakeupcanbeselectedasUDISK/CD/TUNER/IPOD/SD/MMCbyfuthurpressing
 andpressthe"TIMER/EQ"buttontoconrm.
4. WakeupvolumecanbeselectedbypressingtheVOLUME+/-buttonandpressthe"TIMER/EQ"
 buttontoconrm.
5. To enable the TIMER function, press the TIMER/EQ button at standby mode and the unit
will turn on at the selected preset times.
TIMER / EQ
SCDI-01 LENCO ENGLISH IM NO RCA 8 8 15/6/2011 14:48:22

Note:
1. Only the universal dock adaptor no. “1”. “2”,… “7” are supplied in this unit and they can be installed in this unit
universal dock.
2.YoumusthavethecorrectuniversaldockadaptorinplacethattswithyouriPodtoavoidwobbling,causingpoor
electrical contact.
3. Various iPod models can vary in control by SCDI-01.
Listen to iPod ( Controlled by unit ) :
1. With the correct iPod universal dock adaptor installed,
 gentlydocktheiPod (without the protective cover) into
 theunit'suniversaldock.
2. When docked, the Internal iPodbatterywillbecharged
 untilitisfullycharged.
3. Press the FUNCTION button to select iPod mode and the
 songwillbeplayedautomatically.
4. Press the PLAY / PAUSE / I - POD PLAY button to
playback the music." I - POD " will be shown on the display.
5. Press the B - SKIP / I - POD OR F - SKIP /
I - POD buttontoselectthenextorprevioussong.
6. Press the VOLUME + / - button to adjust the volume level.
7. Press the STOP / I - POD STOP button to stop
playback, iPod will be off.
Note:
- This unit display cannot show any music information
 (e.g.songname)ofyouriPod. Please view the music
 informationthroughyouriPod display.
- The iPod canbechargedonlyinonmode.
Universal dock
Adaptor no.
1 3G iPod 10GB, 15GB, 20GB YES
iPod description Capacity Supplied in this unit
(yes / no)
6 iPod photo & Color U2 iPod 20GB & 30GB YES
iPod with color display 20GB
2 3G iPod 30GB & 40GB YES
3 iPod mini 20GB YES
4 4G iPod & U2 iPod 30GB & 40GB YES
5 4G iPod 40GB YES
7 iPod photo 40GB & 60GB YES
iPod with color display 60GB
LISTEN TO iPod AND CHARGING INTERNAL iPod BATTERY
Install the iPod universal dock adapter
1. Select the iPoduniversaldockadaptorthattswithyouriPod model, from the next table. The adapter no. is marked
at the back of the adapter.
2. Installtheadapterwiththetwotabsfacingthefront,bypushingitdownintheuniversaldockattheunitfront.
3. Toremovetheadapterforexchangeoftheothers,Pressatthebackoftheadapterandpullitupward.
Clock setting mode works in stop mode
1. HoldthePROGRAM/MEMORY/CLK-ADJ.buttonclockmode12or24hourswillash.
2. Press the B - SKIP or F - SKIP button to adjust 24 - hour or 12 - hour clock mode.B - SKIP or F - SKIP button to adjust 24 - hour or 12 - hour clock mode.or F - SKIP button to adjust 24 - hour or 12 - hour clock mode.F - SKIP button to adjust 24 - hour or 12 - hour clock mode.button to adjust 24 - hour or 12 - hour clock mode.
3. PressthePROGRAM / MEMORY / CLK - ADJ. button again, the hour digit will ash on the display.PROGRAM/MEMORY/CLK-ADJ. button again, the hour digit will ash on the display.buttonagain,thehourdigitwillashonthedisplay.
4. PresstheB - SKIP or F - SKIP button to adjust the hour digit.B-SKIPor F - SKIP button to adjust the hour digit.orF - SKIP button to adjust the hour digit.F-SKIP button to adjust the hour digit.buttontoadjustthehourdigit.
5. PressthePROGRAM / MEMORY / CLK - ADJ. button again, the minute digit will ash on the display.PROGRAM/MEMORY/CLK-ADJ. button again, the minute digit will ash on the display.buttonagain,theminutedigitwillashonthedisplay.
6. PresstheB - SKIP or F - SKIP button to adjust the minute digit.B-SKIPor F - SKIP button to adjust the minute digit.orF - SKIP button to adjust the minute digit.F-SKIPbutton to adjust the minute digit.buttontoadjusttheminutedigit.
7. PressthePROGRAM / MEMORY / CLK - ADJ. button again, the correct time will be shown on the display.PROGRAM/MEMORY/CLK-ADJ.button again, the correct time will be shown on the display.buttonagain,thecorrecttimewillbeshownonthedisplay.
CLOCK SETTING
GB 7
Listen to iPod ( Controlled by remote ) :
Go to iPod menu, full operation for the iPod
1. With the correct iPod universal dock adaptor installed,
 gentlydocktheiPod (without the protective cover) into
 theunit'suniversaldock.
2. When docked, the Internal iPodbatterywillbecharged
 untilitisfullycharged.
3. Press the FUNCTION button to select iPod mode
4. Press the I - MENU button to enter the iPod menu
control status.
5. Press the I - SELECT button to forward the selection and
playback the music.
6. Press the I - MENU button to backward the selection.
7. PresstheI-UPorI-DOWNbuttontoselectthedesiredle.
8. Press the VOLUME + / - button to adjust the volume level.
9. Press the PLAY / PAUSE / I - POD PLAY button to
playback the music." I - POD " will be shown on the display.
10.Press the B - SKIP / I - POD OR F - SKIP /
I - POD buttontoselectthenextorprevioussong.
11. Press the STOP / I - POD STOP button to stop
playback, iPod will be off.
SCDI-01 LENCO ENGLISH IM NO RCA 9 9 15/6/2011 14:48:22

GB 8
If at any time in the future you should need to dispose of this product please note that: Waste electrical products
should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local
Authorityorretailerforrecyclingadvice.(WasteElectricalandElectronicEquipmentDirective)
Where to place the item :
Today’sfurnitureiscoatedwithawidevarietyoflacquersandsynthetic-coatingsthataretreatedwithanextensiverange
ofcleaningproducts.Therefore,thepossibilitythatsomeofthesesubstancescontaincomponentsthatreactadverselyto
the rubber feet of the item and soften them, cannot be completely excluded. The rubber feet of the appliance can cause
discoloringtofurnituresurfaces.Ifnecessary,placetheapplianceonanon-slidesurface.
SPECIFICATIONS
CD SECTION
Channels: 2 channels
S / N ratio: 60 dB
Wow & Flutter: undetectable
Samplingfrequency: 44.1kHz8xoversampling
Quantization: 1bitDAconverter
Pickuplightsource: Semi-conductorlaser
Pickupwavelength 790nm
RADIO SECTION
Tuningranges: FM87.5-108MHz
 AM522-1620kHz
Antennas : AM Built - in ferrite bar
FM telescopic antenna
GENERAL
Output power: 2 W + 2 W (RMS)
Power consumption: 15 W
Speaker: 3" 8 OHM
Phones jack: 3.5 MM
AUX IN jack 3.5 MM
Powersource: AC:230V~50Hz
DC: 12V 1.5 x 8 UM2 / LR14 / "C" SIZE
Clock back up Battery 1.5 x 3 AAA / LR03
Dimensions:
Main unit 438 (L) x 262 (D) x 143 (H) mm
Remote control : 35 (L) x 18 (D) x 190 (H) mm
Weight 2.7KGS
Duetocontinuingimprovement,thefeaturesandthedesignaresubjecttochangewithoutnotice.
WARNING
ShouldtheCDdoorbeopenedbeforethereadingoftheCD
iscompleted,ajammingnoisemayoccur.Thisisresolved
byclosingtheCDdoor.
CLEANING THE UNIT
Do not use volatile chemicals
onthisunit.Cleanbylightly
wipingwithasoftcloth.
IMPORTANT NOTE
Ifanabnormaldisplayindicationoranoperatingproblem
occurs, disconnect the AC power cord and remove the
batteries. Wait at least 5 seconds, then reconnect the AC
power cord or reinstall the batteries.
CLEANING CD
IftheCDskipsorwillnotplay,thediscmayneedcleaning.
Before playing, wipe the disc from the centre out with a
cleaningcloth.Afterplaying,storethediscinitscase.
MAINTENANCE
CLEANING THE CD LENS
If the CD lens is dusty, clean it with a brush-blower. Blow
several times on the lens and remove the dust with the
brush.Fingerprintsmayberemovedwithacottonswab
moistened with alcohol.
For information and support, www.lenco.eu
SCDI-01 LENCO ENGLISH IM NO RCA 10 10 15/6/2011 14:48:22