Lenel 5000 Series User manual

Quick Installation Guide
Lenel Readers - 5000 Series
Europees distributie centrum (EDC)
Kelvinstraat 7
6003 DH – Weert, The Netherlands
Tel: [phone]
• Option 1 for Customer Service
• Option 1 for Intercompany and Sales oces support
• Option 2 for Return/Repair requests or shipment discrepancies
• Option 3 for all other service inquiries
• Option 2 for Transport and Logistics
• Option 3 for Finance
Fax: [phone]
Email: [email protected]
THESE PRODUCTS ARE INTENDED FOR SALE TO AND INSTALLATION BY QUALIFIED PROFESSIONALS.
UTC FIRE & SECURITY CANNOT PROVIDE ANY ASSURANCE THAT ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY “AUTHORIZED DEALER” OR “AUTHORIZED RESELLER”, IS PROPERLY TRAINED
OR EXPERIENCED TO CORRECTLY INSTALL FIRE AND SECURITY RELATED PRODUCTS.
For more information on warranty disclaimers and product safety information, please check
https://resecurityproducts.com/policy/product-warning or scan the following code:
UTC Fire & Security BV
Contact info
Product Warnings and Disclaimers
When installing the reader to the mounting plate ensure that the reader pin
header contact perfectly aligns with the terminal connector block. Mount
the front cover according to the image above and make sure it is tted
properly (CLICK). To secure the front cover to the reader use the supplied
screw and x it into the readerbody through the front cover.
To open the reader: Use the reader opening tool (LNL-R50000-OT) to avoid
any damage to the front cover and/or mounting plate, remove the front
cover from the mounting plate as shown on the picture to the right.
For all local contact details, please consult the
UTC Fire & Security webpage:
https://www.utcfssecurityproducts.eu/contact.php

Tamper
GPO1
GPO2
GND
B/RX
A/TX
GND
DC+
CP
D1 Clock
D0 Data
GND
G-LED
R-LED
BZ CTRL
K-LED
Tamper output
General purpose I/O
General purpose I/O
Ground
RS485 - / OSDP
RS485 + / OSDP
Power supply
Power supply 9 - 30 VDC
Card Present
Wiegand Data1/Clock/Data, ABA 2
Wiegand Data0/Clock/Data, ABA 2
Ground
External Green LED control
External Red LED control
External Buzzer control
External keypad LED control
PIN Description
Description
Wiegand
Wiegand
x
-
-
-
-
-
x
x
-
x
x
-
x
x
x
x
Terminal description
RS485/
OSDP
RS485/
OSDP
Clock/
Data
Clock/
Data
-
-
-
-
x
x
x
x
-
-
-
-
-
-
-
-
-
-
-
-
x
x
x
x
x
-
-
-
-
-
-
-
P2
P1
PIN
K-LED
BZ CTRL
R-LED
G-LED
GND
D0 Data
D1 Clock
CP
Tamper
GPO1
GPO2
GND
B/RX
A/TX
GND
DC+
P1
P2
Tamper
GPO1
GPO2
GND
B/RX
A/TX
GND
DC+
P1 P2
CP
D1 Clock
D0 Data
GND
G-LED
R-LED
BZ CTRL
K-LED
Quick Installation Guide
Lenel Readers - 5000 Series Standard 13,56MHz
Lenel Readers - 5000 Series Standard 13,56MHz/125kHz
Quick Installation Guide
Lenel Readers - 5000 Series
Slimline 13,56MHz
Please note that this is only a quick installation guide.
Information regarding recommendations, measurements and accessories are
available in the full version of the Lenel Readers - 5000 Series installation guide.
1 Current draw does not include heater consumption.
2 LED settings; LED Bar = Low, Back Light = Low
Please consult table in full installation manual for more information on heater
consumption settings and how the LED-settings will aect current draw.
Power consumption:
Notes
1. Maximum wiegand cable length is 150 meters and requires a high quality
shielded cable with minimum AWG18 dimension (=0.8231mm2) in an environment
free from electrical noise. A cable with smaller dimension or an installation
environment with electrical disturbances will reduce the maximum cable length.
2. Wiegand & Clock/Data requires dedicated wires for external control of Green
LED, Red LED, Buzzer and Keypad backlight.
3. When utilizing the GPI/O’s, each respective GPO1 or GPO2 must be connected
to each respective pin and also to GND. The general purpose input/output will only
be activated if so applied in the reader configuration.
4. RS 485/OSDP requires twisted pair cable.
Model Current draw (idle1) Current draw (peak1,2)
12V 24V 12V 24V
Standard 13.56MHz 50 mA 40 mA 147 mA 99 mA
Combi 13.56MHz/125kHz 90 mA 60 mA 187 mA 119 mA
Slimline 13.56MHz 50 mA 40 mA 164 mA 108 mA