Lennox Hearth Products 1003C User manual

INSTALLATION AND OPERATION
MANUAL
MODEL 1003C
RETAIN THESE
INSTRUCTIONS
FOR FUTURE
REFERENCE
EPA CERTIFIED
CATALYTIC WOOD
BURNING STOVE
THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER.
READ ENTIRE MANUAL THOROUGHLY BEFORE INSTALLATION.
P/N 775003M, Rev. P, 11/03

IMPORTANT WARNINGS
CAUTION: PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR NEW ROOM
HEATER. FOR YOUR SAFETY, FOLLOW THE INSTALLATION, OPERATION AND MAINTENANCE INSTRUC-
TIONS EXACTLY, WITHOUT DEVIATION. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN
PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH. IF THIS APPLIANCE IS NOT PROPERLY INSTALLED,
A HOUSE FIRE MAY RESULT. CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS
AND INSTALLATION INSPECTION REQUIREMENTS IN YOUR AREA.
PAGE 2
1. If utilizing an older chimney, it must be in-
spected for adequate serviceability. Refer to the
heading Chimney Inspection on page 10 of this
manual.
2. The minimum clearances must be maintained
for all combustible surfaces and materials in-
cluding; furniture, carpet, drapes, clothing,
wood, papers, etc. Do not store firewood within
this clearance space. Failure to maintain clear-
ances to all combustibles may result in a house
fire.
3. This appliance requires non-combustible floor
protection as outlined in this manual (see Floor
Protection on page 5 for additional information).
4. Minimum ceiling height must be 7 feet (213 cm)
(measured from base of appliance to ceiling).
5. DO NOT CONNECT THIS UNIT TO A CHIMNEY
FLUE CONNECTED TO ANOTHER APPLIANCE.
6. Do not connect this appliance to air ducts or
any air distribution system.
7. PREVENT CREOSOTE FIRE: Inspect and clean
chimney frequently. Under certain conditions of
use, creosote buildup may occur rapidly. In-
spect chimney connector and chimney twice
monthly and clean if necessary. Using green or
inadequately seasoned wood can greatly in-
crease creosote buildup. Use dry wood to mini-
mize creosote buildup.
8. USE SOLID WOOD FUEL ONLY: This appliance
is approved for burning dry seasoned natural
wood only. CAUTION: BURN UNTREATED
WOOD ONLY. OTHER MATERIALS SUCH AS
WOOD PRESERVATIVES, METAL FOILS, COAL,
PLASTIC, GARBAGE, SULFUR OR OIL MAY
DAMAGE THE CATALYST. DO NOT BURN
GARBAGE OR FLAMMABLE FLUIDS SUCH AS
GASOLINE, NAPHTHA OR ENGINE OIL.
9. Never use gasoline, gasoline-type lantern fuel,
kerosene, charcoal lighter fluid, or similar liq-
uids to start or "freshen up" a fire in this heater.
Keep all such liquids well away from the heater
while it is in use.
10. DO NOT OVERFIRE: If heater or chimney con-
nector glows, you are overfiring. Overfiring this
appliance could cause a house fire. Overfiring is
a condition where the appliance is operated at
temperatures above its design capabilities (see
Overfiring, on page 23). Overfiring can be
caused by improper installation, improper op-
eration, lack of maintenance or improper fuel
usage. Damage caused from overfiring is NOT
covered under the manufacturers limited war-
ranty. (see Care and Operation, pages 14 to 17).
11. NEVER LEAVE AN UNATTENDED STOVE
BURNING ON HIGH. Operation of the stove with
the primary air control at its highest burn rate
setting for extended periods can cause danger-
ous overfiring conditions. The primary air con-
trol should only be positioned at the highest
setting during start-up procedures and for short
durations. When leaving the stove unattended
ensure that the primary air control is set to the
low or medium low range.
12. Use a metal container with a tight fitting lid to
dispose of ashes.
13. IN THE EVENT OF A COMPONENT FAILURE,
USE ONLY COMPONENTS PROVIDED BY THE
MANUFACTURER AS REPLACEMENT PARTS.
14. Burning any kind of fuel uses oxygen from the
dwelling. Be sure that you allow an adequate
source of fresh air into the room where the
stove is operating (see Ventilation, page 11 and
Outside Air, page 8).
15. CAUTION: HOT WHILE IN OPERATION. An ap-
pliance hot enough to warm your home can se-
verely burn anyone touching it. Keep children,
clothing and furniture away. Contact may cause
skin burns. Do not let children touch the appli-
ance. Train them to stay a safe distance from
the unit.
16. Build fires directly upon the brick hearth inside
the stove. Do not use grates, irons or any other
method to elevate the fire.
17. SAVE THESE INSTRUCTIONS.
18. See the listing label located on the back of
stove (or see Safety/Listing Label on page 29).

PAGE 3
TABLE OF CONTENTS
Important Warnings ................................................ 2
Testing/Listing, EPA, Using this Manual.................. 3
Planning Your Installation ..................................... 4-7
Manufactured (Mobile) Home Requirements ...........8
Installation .......................................................... 8-13
Care and Operation .......................................... 14-17
Recommended Fuel ......................................... 17-18
Maintenance ..................................................... 18-20
Troubleshooting ................................................ 21-23
Specifications..........................................................24
Replacement Parts List..................................... 25-27
Optional Accessories ..............................................28
Safety/Listing Label.................................................29
EPA Label ...............................................................30
Ownership Records ...............................................31
TESTING/LISTING
Model 1003C has been tested to UL Standard 1482
and ULC-S627 by OMNI-Test Laboratories Inc.; Bea-
verton, Oregon; Report number #030-S-02-2.
EPA CERTIFICATION
This stove has been tested to rigorous emissions stan-
dard, and has been certified by the Environmental Pro-
tection Agency.
USING THIS MANUAL
Please read and carefully follow all of the instructions
found in this manual. Please pay special attention to the
safety instructions provided in this manual. The Home-
owner’s Care and Operation Instructions included here
will assure you have many years of dependable and
enjoyable service from your appliance.
CONGRATULATIONS ON THE PURCHASE OF
YOUR NEW WOODSTOVE MANUFACTURED BY
LENNOX HEARTH PRODUCTS.
When you purchased your new woodstove, you
joined the ranks of thousands of concerned indi-
viduals whose answer to their home heating needs
reflects their concern for aesthetics, efficiency and
our environment. We extend our continued support
to help you achieve the maximum benefit and en-
joyment available from your new wood stove.
It is our goal at Lennox Hearth Products to provide
you, our valued customer, with an appliance that
will ensure you years of trouble free warmth and
pleasure.
Thank you for selecting a Lennox Hearth Products
stove as the answer to your home heating needs.
Sincerely,
All of us at Lennox Hearth Products
PACKAGING LIST
This appliance is packaged with an accessory package,
which contains the following:
One - Installation and operation instructions
manual.
One - Warranty.
One - Catalytic combustor temperature probe and
sleeve.
One - Damper Hook

PLANNING YOUR INSTALLATION
PAGE 4
QUESTIONS TO ASK LOCAL BUILDING OFFICIAL
A correct installation is critical and imperative for reduc-
ing fire hazards and perilous conditions that can arise
when wood burning appliances are improperly installed.
The installer must follow all of the manufacturers’ in-
structions.
The installation of a wood burning appliance must con-
form to local codes and applicable state and federal
requirements. Familiarity with these requirements be-
fore installation is essential. Important considerations to
discuss with local building officials include:
1. Applicable codes (i.e. Uniform Mechanical Code,
State or Regional Codes.)?
Electrical codes: Optional Blower Assemblies have a
flexible electrical cord that must be electrically
grounded per local codes or per electrical codes:
In USA, NEC, ANSI/NFPA 70-2002.
In Canada, CSA C22.1
WARNING: ELECTRICAL GROUNDING INSTRUC-
TIONS: THIS APPLIANCE IS EQUIPPED WITH A
THREE-PRONG (GROUNDING) PLUG FOR YOUR
PROTECTION AGAINST SHOCK HAZARD AND
SHOULD BE PLUGGED DIRECTLY INTO A PROP-
ERLY GROUNDED THREE-PRONG RECEPTACLE.
DO NOT CUT OR REMOVE THE GROUNDING
PRONG FROM THIS PLUG. DO NOT ROUTE
POWER CORD UNDER OR IN FRONT OF APPLI-
ANCE.
2. Local amendments?
3. Is a permit required - cost?
(You may wish to contact your insurance company
to ask if they require this).
4. Is outside combustion air required?
5. Rooms where the installation is not allowed?
SMOKE DETECTORS
Since there are always several potential sources of fire
in any home, we recommend installing smoke detec-
tors. If possible, install the smoke detector in a hallway
adjacent to the room (to reduce the possibility of occa-
sional false activation from the heat produced by the
stove). If your local code requires a smoke detector be
installed within the same room, you must follow the re-
quirements of your local code. Check with your local
building department for requirements in your area.
SELECTING A LOCATION
The design of your home and where you place your
stove will determine its value as a source of heat. A
wood stove depends primarily on air circulation (con-
vection) to disperse its heat, and therefore, a central
location is often best. There are other practical consid-
erations, which must be considered before a final selec-
tion of locations is made:
♦ Existing Chimneys
♦ Wood Storage
♦ Aesthetic Considerations
♦ Roof Design (Rafter Locations & Roof Pitch)
♦Room Traffic
♦Proximity to Combustibles
♦ Electrical Wiring
The installation of this stove will require some research.
Once your options are determined, consult with your
local building department who will be able to give you
the necessary installation requirements for your area (Is
a building permit required, rooms where installation may
not be allowed etc.).
WARNING: CHECK ALL LOCAL BUILDING AND
SAFETY CODES BEFORE INSTALLATION. THE IN-
STALLATION INSTRUCTIONS AND APPROPRIATE
CODE REQUIREMENTS MUST BE FOLLOWED EX-
ACTLY AND WITHOUT COMPROMISE. ALTERA-
TIONS TO THE STOVE ARE NOT ALLOWED. DO
NOT CONNECT THE STOVE TO A CHIMNEY SYS-
TEM SERVING ANOTHER STOVE, APPLIANCE, OR
ANY AIR DISTRIBUTION DUCT. FAILURE TO FOL-
LOW THESE INSTRUCTIONS WILL VOID THE
MANUFACTURERS WARRANTY.
If you plan to vent your stove into an existing masonry
chimney, have the chimney inspected by a local fire
marshal or qualified installer. Remember that a stove's
performance is heavily influenced by the chimney and
its location on the roof. An oversized flue may not pro-
vide effective draw, and a flue liner may be required
(see Draft Requirements, page 11). Consult your dealer
or qualified installer before final selection is made.
This stove requires pre-installation work to be com-
pleted before installation can take place. This may in-
clude modification for flue and chimney.
NOTE – This appliance IS approved for installation
into a Manufactured (Mobile) Home in Canada and
the USA.

PLANNING YOUR INSTALLATION
PAGE 5
FLOOR PROTECTION
This appliance requires non-combustible floor protec-
tion for ember protection. If the floor protection is to be
stone, tile, brick, etc., it must be mortared or grouted to
form a continuous non-combustible surface. If a chim-
ney connector extends horizontally over the floor, pro-
tection must cover the floor under the connector and at
least 2" (51 mm) to either side.
The floor protection must extend completely beneath
the stove and to the front, sides, and rear as indicated:
USA REQUIREMENTS
16” (406 mm) min. to the front of the fuel door glass
8” (203 mm) min. beyond the sides of the fuel door
opening
0” (0 mm) min. to the back of the stove body
CANADA REQUIREMENTS
18” (457 mm) min. to the front of the fuel door glass
8” (203 mm) min. beyond the sides of the stove body
8” (203 mm) min. to the back of the stove body
STANDARD PARALLEL HEARTH PAD SHOWN
8” (203 mm)
Canada
8” (203 mm)
USA
8” (203 mm)
USA
8” (203 mm)
Canada
0” - USA
8” – Can.
18” (457 mm)
–
Can-
ada
16
”
(406 mm)
USA
DOOR
STOVE TOP

PLANNING YOUR INSTALLATION
PAGE 6
COMBUSTIBLE WALL CLEARANCES
WARNING: IT IS VERY IMPORTANT THAT YOU OB-
SERVE THE MINIMUM CLEARANCES.
There are listed clearances for your stove which were deter-
mined in a Laboratory test using various "classes" of stove pipe
or chimney. Minimums are first established for the stove itself
and increased based on how much heat is transferred by each
class of pipe.
NOTE: Manufactured (mobile) home installations require the
use of a Type L-Vent Chimney connector only. Use of a single
wall flue pipe connection is not permitted.
Manufactured (Mobile) Home Standard and Residential
Reduced - Using 6” (152 mm) diameter Type L-Vent connector
pipe (to the top of the stove) with listed factory-built 103HT
chimney suitable for use with solid fuels or a code approved
masonry chimney. Approved brands of factory built chimney are
Dura-Vent, Security, Jake Evans and Metal Bestos.
MANUFACTURED (MOBILE) HOME INSTALLATIONS MUST
BE EQUIPPED WITH A RAIN CAP AND SPARK ARRESTOR.
Clearances (inches / millimeters)
A. 14 / 356 C. 17 / 432 E. 16 / 406
B. 25 / 635 D. 9 / 229 F. 8 / 203
Residential Standard (not approved for manufactured
[mobile] homes) Using 6” (152 mm) diameter, single wall
connector pipe with listed factory-built to the top of the
stove.
Clearances (inches / millimeters)
A. 22 / 559 C. 25 / 635 E. 16 / 406
B. 25.5 / 648 D. 16 / 406 F. 15 / 381
Residential Note: Approved for 6” (152 mm) diameter,
single wall, minimum 24 MSG black or blued steel con-
nector pipe with listed factory-built 103HT chimney
suitable for use with solid fuels or a code approved
masonry chimney.
Manufactured (Mobile) Home Reduced and Residen-
tial Reduced Using 6” (152 mm) diameter Type L-Vent
connector pipe (to the top of the stove) with listed fac-
tory-built 103HT chimney suitable for use with solid fuels
or a code approved masonry chimney. Approved brands
of factory built chimney are Dura-Vent, Security, Jake
Evans and Metal Bestos. MANUFACTURED (MOBILE)
HOME INSTALLATIONS MUST BE EQUIPPED WITH A
RAIN CAP AND SPARK ARRESTOR. Alcove size: 84”
(213 cm) minimum height, 56” (143 cm) minimum width,
and 24” (610 mm) maximum depth.
Clearances (inches / millimeters)
A. 11 / 280 C. 14.5 / 369 E. 16 / 406
B. 25.5 / 648 D. 5.5 / 140 F. 5.5 / 140
Vent Height (all installations) - The pipe should extend
12 feet above the stove top, as a minimum, to achieve a
stable draft.
Corner Installation
Parallel Installation
C
45°
F
D
A
B
E

PLANNING YOUR INSTALLATION
PAGE 7
ALCOVE CLEARANCES
NOTE:" = inches, mm = millimeter, cm = centimeter
Alcoves must have minimum dimensions of 84" (214 cm)
height, 56" (142 cm) width and 24" (610 mm) maximum
depth.
Require pipe: Type L Vent pipe to the top of the stove.
Manufactured (mobile) home installations must be
equipped with a rain cap and spark arrestor and must
use a pipe shield extending a minimum of 24" (610 mm)
above the stove (resting on stove) is mandatory for the
installation of this appliance into a combustible alcove.
Alcove Dimension Requirements
Alcove Top View / Stove Clearances
ALCOVE CLEARANCES:
Back wall to pipe O.D. 11" / 280 mm
Side wall to pipe O.D. 25.5" / 648 mm
Back wall to stove 5.5" / 140 mm
Side wall to stove 16" / 407 mm
Alcove - Top View
* NOTE: Alcove dimensions cannot be reduced by the
use of non-combustible materials such as brick, stone,
etc. Alcove dimensions listed are minimum dimensions
and are not measurements for building an Alcove. You
will need to consider these clearances, as well as
other dimensional requirements before you build the
alcove and install this appliance.
REDUCED MASONRY STRUCTURE CLEARANCE
(ALCOVE)
Your stove can be installed in a masonry structure with
reduced clearances if the structure was built to National
Building Code for fireplaces and chimneys (UBC 37).
The firebox of the masonry structure must be of ade-
quate size to allow a minimum of 6” (152.4 mm) clear-
ance to the sides and top of the stove and 2” (50.8 mm)
clearance to the rear. All stove models must be installed
on their original listed legs or base unless otherwise
specified by OMNI Testing Laboratory.
The minimum venting requirement is a listed chimney
liner that extends from the flue collar of the stove to the
first tile liner of the chimney where it is sealed. All joints
and connections must be made airtight to prevent leak-
ing and downdrafts.
PROTECTED WALL CLEARANCE
Some local codes will allow reduced clearances when
the stove is installed adjacent to a protected wall system.
Your local building official must approve the variance.
Normally, the protected wall system is defined as a non-
combustible material with a minimum of 1” (25.4 mm) air
space behind. Check your local building codes or with a
qualified installer (Ref. NFPA 211).
56” (143 cm)
Minimum
24” (610 mm)
Depth
Maximum
84”
(214 cm)
Min.
16”
(407 mm)
25.5”
(648 mm)
5.5” (140 mm)11” (280 mm)

INSTALLATION
PAGE 8
AIR INTAKE COVER
The pedestal is equipped with an air intake cover (lo-
cated at the top front of the pedestal). The air intake
cover should be adjusted to the open position if outside
combustion air is NOT provided. If outside combustion
air is provided, adjust to the closed position (see illustra-
tion to the right).
OUTSIDE AIR
In all manufactured (mobile) homes and in many site
built residences (subject to local code), a stove may be
required to use outside air for combustion. A 5 ¼” (133
mm) square outside air floor duct is available through
your dealer.
This stove can take in outside air directly through the
base. This type installation requires a hole through the
floor protector and the use of outside air floor duct (cata-
log # 14M67) to penetrate into the air space below the
home. When outside air is hooked up, the Air Intake
Cover must be adjusted to the closed position (see Air
Intake Cover section on this page).
NOTE: Because the base sits 1” (25.4 mm) off the floor,
the outside air floor duct can be positioned along the
front to rear center line under the pedestal, but as close
to the opening in the base as location permits. The air
duct opening must be protected from any possible ob-
struction including loose floor insulation.
MANUFACTURED (MOBILE) HOME REQUIREMENTS
This stove is certified as a Room Heater, Solid Fuel Type
and may be used in Manufactured Housing providing the
following requirements are followed:
• An outside air inlet must be provided for combustion
and be unrestricted while unit is in use.
• WARNING: DO NOT INSTALL IN SLEEPING
ROOM.
• Regulations require that the appliance must be se-
cured to the floor and grounded to the chassis. See
Securing the Stove to the Floor (and) Grounding
Stove.
• Required venting is 6” (152 mm) diameter Type L-
Vent connector pipe with listed factory-built 103HT
chimney suitable for use with solid fuels or a code
approved masonry chimney. Approved brands of fac-
tory built chimney are listed in this manual. A rain
cap and spark arrestor is required (see Clearances,
pages 6 & 7).
• CAUTION: THE STRUCTURAL INTEGRITY OF
THE MOBILE HOME FLOOR, WALL, AND CEIL-
ING/ROOF MUST BE MAINTAINED.
• The chimney must provide for a section joint so that
any parts extending above 13’ 6” (411 cm) from
ground level can be removed for transportation of the
mobile dwelling.
Air Intake
Cover
Open Closed
Pedestal
Front
Floor Protector
Stove Outside
Air Floor
Duct

INSTALLATION
PAGE 9
SECURING THE STOVE TO THE FLOOR
Manufactured (Mobile) Homes Only
Once the outside air floor duct is in position, replace the
floor protector. Make sure that the floor protector's hole is
aligned with the outside air opening. Next position and
align the stove on the hearth pad. Manufactured (mobile)
home installations require that the stove be secured to
the floor. This ensures that the stove will not shift when
the manufactured (mobile) home is moved. To do this,
mark where the holes are to be drilled using a marking
instrument long enough and small enough to fit through
the (4) four holes in the stove base. Mark holes, then
remove the stove. Drill the (4) four holes, with a ¼” (7
mm) drill bit. Drill down through the floor protector and
the manufactured (mobile) home floor. Use ¼” (7 mm)
lag bolts and secure to the manufactured (mobile) home
floor.
NOTE: If the composition of the manufactured (mobile)
home floor is of light particleboard construction, you will
be required to secure the stove with regular hex head
bolts and nuts. This will ensure that the bolts will not rip
out of the floor when the manufactured (mobile) home is
being moved.
GROUNDING STOVE
Manufactured (Mobile) Homes Only
Regulations require that all stoves installed in manufac-
tured (mobile) homes must be grounded. To do this sim-
ply attach a piece of No. 8 copper wire, at least 18” (457
mm) in length from the stove to the chassis of the manu-
factured (mobile) home.
INSTALLING CATALYTIC TEMPERATURE PROBE
Locate the temperature probe with sleeve in the literature
packet. Insert sleeve, then temperature probe into the ¼”
(7 mm) diameter hole on the stove top.
REMOVE ASH DRAWER CLIP
The ash drawer is secured for shipping with a small re-
taining screw at the top of drawer. Remove and discard
this screw.
TYPES OF CHIMNEYS
The chimney is a vital part of your stove installation. A
properly built masonry chimney or a properly installed
factory built chimney will assure a consistent draft under
a variety of weather conditions (a smoking stove is usu-
ally caused by a chimney problem). The stove flue size is
6” (152 mm) diameter, which is approximately 28 square
inches (712 square millimeters) minimum. The maximum
flue size should be no more than (3)-three times the
cross sectional area of the size of the stove flue collar. In
this case, that would be no larger than a 10“ (254 mm)
diameter stack, or approximately 85 square inches (216
square centimeters) maximum.
All chimneys must be installed as specified by local
building codes and according to the chimney manufac-
turer instructions (in the case of a factory built chimney).
See the chimney manufacturer instructions for exact
specifications. Factory built chimneys must comply with
UL 103HT or ULC S629.
ACCEPTABLE CONNECTOR PIPE FOR INSTALLA-
TIONS
For Standard Residential Clearances: Six 6 inch (152
mm) minimum, single wall, 25 gage minimum thickness,
stove pipe is acceptable. Three (3) pre-drilled holes are
provided in the flue collar for fastening the pipe securely
to the stove. Use sheet metal screws to do this. Addi-
tional sections of single wall pipe should be fastened to-
gether with at least three (3) sheet metal screws each
section. When connecting to the factory built ceiling sup-
port package, use the manufacturer's transition piece,
usually called a dripless connector, to join single wall
pipe to their factory built chimney section.
Minimum Flue Size: The required minimum diameter
and area required for the flue size is (respectively) 6
inches / 152 mm diameter, which is approximately 28
square inches / 711 square mm. The maximum flue size
should be no more than (3) three times the cross sec-
tional area of the size of the 6 inches / 152 mm diameter
flue collar. In this case, that would be no larger than a 10
inch (254 mm) diameter (area = approx. 85 sq. inches
[216 sq. cm]).
Connection To A Factory Built Chimney: This space
heater is to be connected to a factory-built chimney con-
forming to CAN / ULC – S629, Standard for 650°C Fac-
tory-Built Chimneys.
For Reduced Residential Clearances: Type L and
listed double wall connector pipe is acceptable. Install
any factory built brand of pipe according to the manufac-
turer's instructions.
Tile-lined
Masonry
Chimney
Factory
Built
Chimney

INSTALLATION
PAGE 10
CHIMNEY INSPECTION
Existing chimneys must be inspected before installing
your stove. Consult your local building department for
chimney code requirements. A masonry chimney must
have a code approved liner. This liner must not have bro-
ken or missing pieces. Some non-code masonry chim-
neys may be brought up to code by being relined. (Con-
sult your dealer or qualified chimney sweep). Factory
built chimneys should also be inspected, first for creo-
sote deposits (which should be removed), and then for
integrity of the stainless steel liner. Look for obvious
bulges in the lining, which may indicate the need to re-
place that section (use a bright flashlight).
Also, inspect the attic to see that the chimney has proper
clearance to combustible framing members. For interior
masonry chimneys and most factory-built chimneys, this
must be a 2“ (51 mm) air space clearance, which must
not be filled with insulation or any other material. An ex-
terior masonry chimney must have a 1“ (25.4 mm) air
space clearance.
Vapor Barrier At Chimney Penetration
Install all venting components per the Vent Manufactur-
ers installation instructions. Ensure that there is an effec-
tive vapor barrier at the location where the chimney
penetrates to the exterior of the structure. This can be
accomplished by applying a non-hardening waterproof
sealant to the following components:
• Around the chimney at the point where the storm
collar will meet the chimney just above the Flashing.
• Along the vertical seam of the chimney pipe, where it
is exposed to the weather.
• On each nail head on the flashing.
• Around the chimney at the point where the storm
collar will meet the chimney just above the flashing.
Notes:
• On a flat or tarred and graveled roof, nail and seal
the flat roof flashing to the roof on all sides with roof-
ing compound.
• Do not put screws through the flashing into the chim-
ney pipe.
CHIMNEY HEIGHT REQUIREMENTS
The chimney must extend 3 feet (914 mm) above the level
of roof penetration and a minimum of 2 feet (610 mm)
higher than any roof surface within 10 feet (305 cm) (see
below). Check with your local building officials for any addi-
tional requirements for your area.
Due to prevailing winds, local terrain, adjacent tall trees, a
hill, or ravine near the home, or adjacent structures, addi-
tional chimney height or a special chimney cap may be re-
quired to ensure optimum performance.
The 2’ by 10’ Rule for Vent Termination
The top of the flue must be 2’ (610 mm) higher than any
part of the roof within 10’ (305 cm) horizontal and a mini-
mum of 3’ (915 mm) higher than the highest point of roof
penetration.
For Manufactured (Mobile) Homes Only:Portions of
the chimney and termination that exceed an elevation of
13½ feet above ground level may be designed to be re-
moved for transporting the manufactured (mobile) home.
Requires A Listed
Termination Cap
2’ (610mm)
10’ (305 cm)
3’ (915mm)

INSTALLATION
PAGE 11
DRAFT REQUIREMENTS
The appliance is merely one component of a larger sys-
tem. The other equally important component is the vent-
ing system which is necessary for achieving the required
flow of combustion air to the fire chamber and for safely
removing unwanted combustion byproducts from the ap-
pliance. If the venting system's design does not promote
these ends, the system may not function properly. Poorly
functioning venting systems may create performance
problems (i.e. smoking stove, poor heat output, fire goes
out, window blackens, increased creosote buildup, etc.)
as well as be a safety hazard. Some factors that may
lead to performance problems are as follows:
• Oversized or undersized chimney.
• Excessive offsets in venting.
• Insufficient vertical height of chimney.
• Insufficient chimney termination height in relationship
to roof.
• Insufficient ventilation.
• Lack of maintenance.
• Improper operation.
• Burning improper fuel (unit is approved for use with
natural dry well-seasoned wood only).
• Down drafts in the chimney (may need a special wind
cap).
To ensure that the venting system is functioning properly
a draft test should be performed (see Draft Test Proce-
dure on this page).
American National Standards Institute ANSI/NFPA 211-
92: A chimney or vent shall be so designed and con-
structed to develop a flow sufficient to completely re-
move all flue and vent gases to the outside atmosphere.
The venting system shall satisfy the draft requirements of
the connected appliance in accordance with the manu-
facturer instructions.
DRAFT TEST PROCEDURE
After this appliance is installed a draft test should be per-
formed to ensure proper draft. A qualified technician
should perform the draft test procedure as follows:
1) Close all windows and doors in the dwelling.
2) Turn on or operate all appliances which remove air
from the home (such as a furnace, heat pump, air
conditioner, clothes dryer, exhaust fans, fireplaces,
and other fuel burning appliances).
3) Drill a hole in the vent pipe per the draft gauge
manufacturers instructions (to create a draft test
port). Note: Hole location should be a minimum of 1
foot above flue outlet collar.
4) Start a fire (See How To Start And Maintain A Fire
on page 16).
5) After the fire is well established (20-25 minutes) and
burning at a low setting, perform the draft test per the
gauge manufacturer instructions. The draft gauge
should read between .05 and .07” W.C. (inches water
column). Excessive draft (above .07 W.C.I.) can result in
too much combustion air to be pulled into the firebox, this
will produce hotter burns and could result in overfiring.
Too little draft (below .05” W.C.) will not allow enough
combustion air delivery to maintain a fire well or cause
performance problems such as smoking (this may result
in improper operation of appliance, i.e. will not maintain
fire well unless ash drawer or fuel door is left open).
6) Install a screw to seal the draft test port in the vent pipe.
If the draft test reading was not within the required range,
correct the installation and repeat this procedure.
VENTILATION REQUIREMENTS / PROVIDE ADE-
QUATE AIR FOR COMBUSTION
THE FRESH AIR REQUIREMENTS OF THIS APPLI-
ANCE MUST BE MET WITHIN THE SPACE WHERE IT
WILL BE INSTALLED. VENTILATION IS ESSENTIAL
WHEN USING A SOLID FUEL BURNING HEATER.
In well insulated and weather tight homes, it may be diffi-
cult to establish a good draft up the chimney (caused by
a shortage of air in the home). The lack of air is caused
by many common household appliances which exhaust
air from the home (such as a furnace, heat pump, air
conditioner, clothes dryer, exhaust fans, fireplaces, and
other fuel burning appliances). Also, the combustion pro-
cess of this heater uses oxygen from inside the dwelling.
If the available fresh air delivery in the dwelling is insuffi-
cient to support the demands of these appliances, prob-
lems can result (i.e. excessive negative pressure can
develop in the dwelling which will affect the rate at which
this appliance can draft thus resulting in performance
problems; See Draft Requirements on this page). To cor-
rect this problem it may help to open a window (prefera-
bly on the windward side of the house) or install a vent to
provide make-up air into the dwelling.

INSTALLATION
See Pipe Manufacturers Instructions For Installation Requirements Of Venting Components And Vent Clearances.
PAGE 12
RESIDENTIAL STANDARD
Using 6” (152 mm) Diameter Single Wall
Connector Pipe. Not Approved For
Manufactured (Mobile) Homes.
MANUFACTURED (MOBILE) HOME STANDARD
Using 6” (152 mm) Diameter Type L-Vent Connector Pipe
IMPORTANT NOTES:
• Minimize the use of elbows (30°, 45°or 90°)- Offsets in the
venting system are very restrictive and will inhibit the draft
(i.e. You will lose approximately 5 feet of effective draft for
every 90 degrees of direction change). This appliance re-
quires 12 to 15 feet of effective draft for optimum perform-
ance (see Draft Requirements on page 11).
• First section of pipe must be vertical - Use as much straight
vertical pipe directly above the appliance as possible be-
fore using an elbow (a 2’ to 3’ initial vertical rise is sug-
gested).
Chimney
Termination Cap
Storm
Collar
Roof
Flashing
Ceiling Support
Assembly
Slip Adapter
Chimney
Connector
6” x 24”
24-Gage
Single Wall Pipe
5 ¼” (134 mm)
Floor
Protection
Square, Outside
Air Floor Duct
7 ft. (214 cm)
Minimum
DVL Close
Clearance
Connector
Support Box
Minimum 12-
15 ft. (366-
458 cm) of
Flue to
Achieve a
Stable Draft
14.5”
(369 mm)
3 ft. (915 mm)
Minimum
Spark Arrestor Cap
Storm Collar
Flashing

INSTALLATION - Combustible Wall Chimney Connector Pass-Throughs
PAGE 13
NOTES:
1. Connectors to a masonry chimney, excepting method B, shall extend in one continuous section through
the wall pass-through system and the chimney wall, to but not past the inner flue liner face.
2. A chimney connector shall not pass through an attic or roof space, closet or similar concealed space, o
r
a floor, or ceiling.
3. Where passage through a wall, or partition of combustible construction is desired, the installation shall
conform to CAN/CSA-B365.
Method A. 12” (304.8 mm) Clearance to Combustible Wall Mem-
ber: Using a minimum thickness 3.5” (89 mm) brick and a 5/8”
(15.9 mm) minimum wall thickness clay liner, construct a wall
pass-through. The clay liner must conform to ASTM C315 (Stan-
dard Specification for Clay Fire Linings) or its equivalent. Keep a
minimum of 12” (304.8 mm) of brick masonry between the clay
liner and wall combustibles. The clay liner shall run from the brick
masonry outer surface to the inner surface of the chimney flue
liner but not past the inner surface. Firmly grout or cement the
clay liner in place to the chimney flue liner.
Method B. 9” (228.6 mm) Clearance to Combustible Wall Member:
Using a 6” (152.4 mm) inside diameter, listed, factory-built Solid-
Pak chimney section with insulation of 1” (25.4 mm) or more, build
a wall pass-through with a minimum 9” (228.6 mm) air space be-
tween the outer wall of the chimney length and wall combustibles.
Use sheet metal supports fastened securely to wall surfaces on all
sides, to maintain the 9” (228.6 mm) air space. When fastening
supports to chimney length, do not penetrate the chimney liner
(the inside wall of the Solid-Pak chimney). The inner end of the
Solid-Pak chimney section shall be flush with the inside of the ma-
sonry chimney flue, and sealed with a non-water soluble refractory
cement. Use this cement to also seal to the brick masonry pene-
tration.
Method C. 6” (152.4 mm) Clearance to Combustible Wall Mem-
ber: Starting with a minimum 24 gage (.024” [.61 mm]) 6” (152.4
mm) metal chimney connector, and a minimum 24 gage ventilated
wall thimble which has two air channels of 1” (25.4 mm) each,
construct a wall pass-through. There shall be a minimum 6”
(152.4) mm separation area containing fiberglass insulation, from
the outer surface of the wall thimble to wall combustibles. Support
the wall thimble, and cover its opening with a 24-gage minimum
sheet metal support. Maintain the 6” (152.4 mm) space. There
should also be a support sized to fit and hold the metal chimney
connector. See that the supports are fastened securely to wall
surfaces on all sides. Make sure fasteners used to secure the
metal chimney connector do not penetrate chimney flue liner.
Method D. 2” (50.8 mm) Clearance to Combustible Wall Member:
Start with a solid-pak listed factory built chimney section at least
12” (304 mm) long, with insulation of 1” (25.4 mm) or more, and an
inside diameter of 8” (2 inches [51 mm] larger than the 6” [152.4
mm] chimney connector). Use this as a pass-through for a mini-
mum 24-gage single wall steel chimney connector. Keep solid-pak
section concentric with and spaced 1” (25.4 mm) off the chimney
connector by way of sheet metal support plates at both ends of
chimney section. Cover opening with and support chimney sec-
tion on both sides with 24 gage minimum sheet metal supports.
See that the supports are fastened securely to wall surfaces on all
sides. Make sure fasteners used to secure chimney section do not
penetrate chimney flue liner.
D
C
B
A
Min. 12 in.
(304.8mm)
to Co
m
bustibles
Masonr
y
Chimney
Fire Clay
Liner
Chimney
Connector
Min. Clearance 12 in.
(304.8mm) of Brick
Min. Chimney Clearance to Brick &
Combustibles – 2 in. (50.8mm)
Chimney Flue
Factory Built
Chimney Length
Air Space – 9 in.
(228.6mm) Min.
Chimney Length
Flush with In-
side of Flue
Min. Clearance
9 in. (228.6mm)
Chimney
Connector
Use Chimney
Mfrs. Parts to
Attach Connec-
tor Securely
Soli
d
-Insulated
Listed Factory-
Built Chimney
Length
Sheet Steel Su
pp
orts
Chimney Flue
Min. Chimney Clearance from Masonry to Sheet Steel
Supports & Combustibles – 2 in. (50.8mm)
Nonsoluble
Refractory
Cement
Min. Chimney Clearance from Masonry to Sheet Steel
Supports & Combustibles – 2 in. (50.8mm)
Chimney
Connector
2 Air Channels, Each 1
in. (25.4 mm)
Min. 6 in.
(152.4mm) glass
Fiber Insulation
2 Ventilated Air
Channels, Each
1 in. (25.4 mm)
Construction of
Sheet Steel
Sheet Steel Su
pp
orts
Masonr
y
Chimney
Chimney Flue
Min. Chimney Clearance
from Masonry to Sheet
Steel Supports & Com-
bustibles – 2 in.
(50 8 )
Sheet Steel
Supports
Chimney
Connector
Chimney
Section
Air Space – 2 in.
(50.8mm) Min.
Masonr
y
Chimney Sheet
Steel
Supports
Chimney
Connector
Chimney
Length
1 in. (25.4 mm)
Air Space to
Chimney
Length
Min. Clearance
2 in. (50.8 mm)

CARE AND OPERATI0N
PAGE 14
ASH DRAWER
The large ash drawer located on the left side of the ped-
estal is designed to make cleaning easier by containing
the ashes in a removable drawer.
WARNING: DO NOT OPERATE THIS STOVE WITHOUT
THE ASH DRAWER PROPERLY INSTALLED AND SE-
CURED (SEALED), AS THIS WILL PRODUCE EX-
TREME TEMPERATURES, RESULTING IN OVERFIR-
ING. THE ASH DRAWER GASKET PROVIDES AN IM-
PORTANT SEAL, AND MUST BE MAINTAINED (SEE
MAINTENANCE REQUIREMENTS ON PAGE 19).
OVERFIRING CAN RESULT IN DAMAGE TO THE AP-
PLIANCE OR A HOUSE FIRE. OPERATION WITH THE
ASH DRAWER OPEN OR AJAR, NULLIFIES THE
SAFETY LISTING AND VOIDS THE WARRANTY.
CATALYTIC COMBUSTOR
How it works: From 5 to 30 percent of the chemical en-
ergy contained in every log escapes up the chimney
when wood is burned in a conventional stove. The cata-
lytic combustor is designed to make use of this energy,
converting it into useful heat as it lessens chimney creo-
sote build-up and air pollution. The catalytic combustor
consists of a durable temperature resistant ceramic com-
position, which is extruded into a cellular, or honeycomb,
configuration. After extrusion, this ceramic monolith is
fired and then covered with a noble-metal catalyst. When
wood smoke contacts this catalyst, chemical changes
occur that causes the smoke to ignite at temperatures
around 600°F. Normally, smoke will ignite and burn only
at temperatures around 1000°F.
CATALYTIC BYPASS DAMPER CONTROL
The operating handle of your Bypass Damper Control is
located on the front of the Stove Flue Collar. By moving
the Bypass Damper Control the operator can route the
exhaust either through the Catalytic Combustor (pushed
in) or directly up the flue (pulled out). When starting a fire
or refueling, the bypass damper control handle should be
pulled out. Once the fire is established it should be
pushed in.
PRIMARY AIR CONTROL
The primary combustion air delivery is controlled by the
Primary Air Control Assembly. The control handle is lo-
cated on the lower right side (front) of the stove - see
illustration below. The heat output can be controlled by
sliding the handle to a higher or lower heat output set-
ting. The fuel, the amount of heat and burn times de-
sired, the type of installation are all variables that will
affect the control setting. The same control settings in a
variety of installations will produce different results. You
will need to try different settings so you can learn how
much heat to expect and how long the fire will burn.
Primary Air Control Handle
Slide the control to the left for a lower burn
rate, to the right for a higher burn rate.
LOW HIGH
You will generally want to set the primary air control on
low or medium. The stove is safe burning on any setting
as long as combustibles are kept at the specified safe
distances.
Ash
Drawer
Secondary Air Tube
Bypass Damper Control
Damper
Door
Positioning
Stops
Tunnel Baffle
Catalytic
Combustor
Catalyic Combustor
Retainer Clip

CARE AND OPERATION
PAGE 15
FUEL DOOR
The gold or black door option is purchased separately,
but is required. Install the door per instructions provided
in kit (see page 28 for ordering information).
WARNING: DO NOT OPERATE THIS STOVE WITHOUT
THE DOOR PROPERLY INSTALLED AND SECURED
AS THIS WILL PRODUCE EXTREME TEMPERATURES
(OVERFIRING). THE DOOR AND GLASS GASKETS
PROVIDE IMPORTANT SEALS, AND MUST BE MAIN-
TAINED (SEE MAINTENANCE REQUIREMENTS ON
PAGE 19). OVERFIRING CAN RESULT IN DAMAGE TO
THE APPLIANCE OR A HOUSE FIRE. OPERATION
WITH THE DOOR OFF OR OPEN NULLIFIES THE
SAFETY LISTING AND VOIDS THE WARRANTY.
Door Operation: The door handle assembly opens and
securely latches the fuel door closed. To open the door,
rotate the coil handle to the 9:00 position until door re-
leases. To close and latch, hold the coil handle in the 9:00
position, close the door, then rotate the handle to the 6:00
position. See illustration below.
CAUTION: WHEN OPENING THE DOOR, DO NOT EX-
TEND IT BEYOND ITS NORMAL TRAVEL. OVEREX-
TENDING THE DOOR TO A FURTHER OPEN POSITION
CAN PUT EXCESSIVE STRESS ON HINGE AREA OF
DOOR AND HINGE PINS AND MAY RESULT IN BREAK-
AGE.
Gold Doors: Gold doors are plated with 24-karat indus-
trial grade gold and will require curing to harden the gold.
Once it is cured it will never tarnish. Prior to burning this
appliance the doorframe should be cleaned thoroughly
with a good window cleaning solution and a soft cloth.
Do not use any metal polishes or abrasives to clean the
gold surface. Any oils or fingerprints left on the gold
could become permanent blemishes if the stove is
burned prior to their removal. After the first few fires, the
gold will cure. The ¾” (19 mm) door rope gasket is
made of highly durable high temperature resistant mate-
rial. It must be kept in good condition. Do not leave the
stove burning with the door ajar or open. Leaving the
door ajar or open while the stove is burning will cause
excessive heat build up in the stove (overfiring) and
could ignite surrounding combustibles as well as damage
the stove (such damage is not covered by the manufac-
turers warranty).
GLASS
The Glass is a super heat resistant ceramic that with-
stands continuous temperatures up to 1390° F. This tem-
perature is well beyond the temperatures in which you
operate your stove. If the glass ever becomes damaged
in any way, replace it, using only 5 mm ceramic glass
(part # G2000-7).
This appliance is designed to provide a flow of air over
the inside of the glass, which along with high heat helps
keep it clean. When operating the stove on low for ex-
tended periods of time, the glass may get dirty. A short,
hot fire (15 - 20 minutes) will help clean off much of the
normal buildup (see Troubleshooting, pages 21-23). A
commercial glass cleaner designed for stoves is recom-
mended for cleaning.
The glass should be cleaned thoroughly with glass
cleaner and a soft cloth BEFORE the stove is burned.
USE CONTROL SETTINGS THAT WORK FOR YOU
The fuel, the amount of heat you want, the type of instal-
lation you have and how long you wish the fire to burn
are all variables that will affect the control settings. The
same control settings in a variety of installations will pro-
duce different results.
Familiarize yourself with your stove by trying different
settings so you can learn how much heat to expect and
how long the fire will burn. It may take a week or two to
learn, but your patience will be rewarded by the warmth
and pleasant satisfaction that only a wood fire can pro-
vide.
To Open, Rotate Handle 90
Degrees Clockwise
Fuel Door

CARE AND OPERATION
PAGE 16
BREAK-IN PERIOD
Your stove finish is a high temperature paint that re-
quires time and temperature to completely cure. We rec-
ommend that you ventilate the house during the initial
burns. The paint emits non-toxic odors during this proc-
ess.
KEEP YOUR HOUSE WELL VENTILATED DURING
THE CURING PROCESS TO PREVENT ACTIVATION
OF YOUR HOME SMOKE DETECTOR.
The paint manufacturer recommends three burn cycles
to cure the paint. The first two burns should be low heat,
approximately 250° F., for 20 minutes each, using paper
and light kindling.
After each 20-minute burn, allow the appliance to cool
completely. The third burn should be at least medium
high or about 450° F. for 45 - 60 minutes. The paint will
become soft and emit non-toxic haze during these burns.
Keep the area well ventilated.
As the paint cures it will become slightly lighter in color.
Eventually the entire surface will become an even color.
Once the paint has been softened and cooled two or
three times, it will harden. Do not turn on a blower during
the curing process. Do not place anything on the stove
surface until the paint is completely cured. Do not at-
tempt to repaint the stove until the paint is completely
cured. If the surface later becomes stained or marred, it
may be lightly sanded and touched up with spray paint
from the same paint manufacturer (See Small Area Paint
Touch-Up, page 18). Paint is available at your local au-
thorized Lennox Hearth Products dealer. Never attempt
to paint a hot stove.
CATALYTIC COMBUSTOR
During the start-up of a cold stove, a medium to high fir-
ing rate must be maintained for about 20 minutes. The
high firing rate will ensure that the stove, the flue, the
catalyst, and the fuel are all stabilized at proper operat-
ing temperatures. Even though it's possible to have tem-
peratures in the stove reach 600° F. within two or three
minutes after the fire is started, do not set the primary air
control lever to the "LOW" position until approximately
twenty minutes have passed. Setting the primary air
control on "LOW" too early could result in either the fire
or the catalytic combustor going out.
At the end of a burn cycle, it's possible that the hot em-
bers remaining might not provide sufficient fuel value for
the catalyst to retain its minimum operating temperature
of 600° F. During the refueling, we recommend that the
stove be refired for about 10 minutes with the bypass
open to ensure a good draw is established and that the
catalyst reaches 600° F. The refiring will ensure sufficient
temperatures and proper amounts of volatiles for the
catalyst to operate properly.
When refueling a hot stove with the catalyst still operat-
ing, no refiring step is necessary. Just open the bypass,
set the primary air control to high, open the door ap-
proximately ½” (1 cm), and wait for about thirty seconds.
Load the fuel, close the door, close the bypass and set
the primary air control to normal operation. Tempera-
tures within the firebox should be hot enough to maintain
the catalytic operation.
HOW TO START AND MAINTAIN A FIRE
1. Check to be sure the grate is in place and the ash
drawer is closed.
2. Open the bypass damper control by pulling it toward
you. In the "OPEN" position the draft air will bypass
the catalytic combustor and make starting the fire
easier.
3. Set the primary air control lever on "HIGH". The
"HIGH" setting will maximize your primary combus-
tion air.
4. Build a fire directly on the firebrick covering the bot-
tom of the stove.
a. Place five or six loosely crumpled sheets of
newspaper in the stove.
b. Add a small amount of dry kindling randomly on
the top of the newspaper.
c. Place a few more loosely crumpled newspapers
on top of the kindling and light the bottom paper
first, then light the top paper. Once the kindling is
ignited and burning on its own, close the fuel
door. The upper fire should help preheat the
chimney and create an effective draft while the
lower fire ignites the kindling.
5. When the kindling is burning well, add increasingly
larger pieces of wood until the fire is actively burn-
ing.
6. When the fire is well established, use the damper
hook and close the bypass by pushing the control
rod in (catalytic temperature probe should read
600°F, takes approximately 20 - 25 minutes to
reach this temperature).
7. When the fire is well-established slide the air control
lever for the desired heat output.

CARE AND OPERATION FUEL
PAGE 17
REFUELING
To refuel the stove, open the bypass damper and move
the primary air control to "HIGH." Let the fire "LIVEN UP"
for about one minute. Open the fuel door about ½” (1 cm)
and hold in this position about 30 seconds or until the
stove is drafting well. Open the door and add wood. After
refueling, reset the primary draft control to the desired po-
sition, and close the bypass when the catalytic tempera-
ture probe reaches operating temperatures of 600°F indi-
cated on the temperature probe.
BYPASS DAMPER CONTROL
The operating handle of your bypass damper control is
located on the front of the stove flue collar. By moving
the bypass damper control, the operator can route the
fire either through the catalytic combustor (pushed in) or
directly up the flue (pulled out). When starting a fire or
refueling, the bypass damper control must be pulled out.
Once the fire is established, it must be pushed in.
CATALYTIC TEMPERATURE PROBE
The catalytic temperature probe monitors the tempera-
ture of your catalytic combustor. Once you have estab-
lished a fire and the catalytic temperature probe indi-
cates the temperature of your catalytic combustor. When
it reaches a temperature of 600 degrees (approximately
20 - 25 minutes), close the bypass damper control. De-
pending on the type and size of the fuel load as well as
the length of time the stove has been burning, your cata-
lytic combustor should operate –between 1000 to 1800
degrees.
When the optional blower is operating it will affect the
temperature probe reading. Turn the blower off for an
accurate reading.
BURN RECOMMENDED FUEL
This appliance is approved for use with untreated natural
dry wood only (see Important Warnings, page 2, #8).
Burning materials other than natural wood will shorten
the life of the catalytic combustor. Do not burn particle-
board or pressed logs using bonding agents as they can
produce conditions, which will deteriorate metal or dam-
age the catalyst. Green or uncured wood does not work
well as fuel, and can cause increased creosote buildups
and plugging of the catalytic combustor. The value of
green wood as a source of heat is limited. Do not over-
load or use kindling wood or mill ends for primary fuel as
this may cause overfiring. Overfiring is a condition where
excessive temperatures are reached, beyond the design
capabilities of the stove. The damage that occurs from
overfiring is not covered under the stove warranty.
WARNING: BURNING IMPROPER FUEL (I.E. CHAR-
COAL) CAN RESULT IN CARBON MONOXIDE POISON-
ING WHICH MAY LEAD TO DEATH!
CARBON MONOXIDE POISONING – EARLY SIGNS
OF CARBON MONOXIDE POISONING RESEMBLE
THE FLU WITH HEADACHES, DIZZINESS, OR NAU-
SEA. IF YOU HAVE THESE SIGNS, GET FRESH AIR
AT ONCE! HAVE THE HEATER INSPECTED BY A
QUALIFIED SERVICE TECHNICIAN. SOME PEOPLE
ARE MORE AFFECTED BY CARBON MONOXIDE
THAN OTHERS. THESE INCLUDE PREGNANT
WOMEN, PEOPLE WITH HEART OR LUNG DISEASE
OR ANEMIA, THOSE UNDER THE INFLUENCE OF
ALCOHOL, AND THOSE AT HIGH ALTITUDES.
WHY SEASONED WOOD?
The key to the success of a good fire that produces heat
from a woodstove is the wood. It needs to be well-
seasoned natural wood.
What does “Well-Seasoned” mean? When a tree is cut
down, the wood is green, full of sap and moisture. This
moisture content can exceed 80%, which must be re-
duced to less than 20%. Wood properly seasoned is then
capable of generating the heat the stove was designed
to provide.
Green wood does not burn easily. Attempting to burn
green wood often results in a lot of smoke and very little
fire. Time is the most important factor in seasoning
wood. Ideally the moisture content should be reduced to
11-20%, although very few of us will be able to check
that figure. There are several steps that should be taken
to ensure that that you come close to these figures.
Secondary Air Tube
Bypass Damper Control
Damper
Door
Positioning
Stops
Tunnel Baffle
Catalytic
Combustor
Catalyic Combustor
Retainer Clip

FUEL MAINTENANCE
PAGE 18
SEASONING GUIDE
Softwoods – 6 months to 18 months
Hardwoods – 12 months to 24 months
Logs that are 5” (127 mm) diameter across or larger
should be split in half, three pieces if over 8” (203 mm),
and four pieces when over a foot (305 mm) across. If
the tree was fell 2 to 4 years ago, it still needs to be cut,
split, and seasoned for 6 to 24 months depending on
the wood.
WOOD STORAGE
Wood to be seasoned should be stacked in an area
open enough to ensure good air circulation on both
sides – leaving adequate space between woodpiles to
walk comfortable. Do not stack wood against a wall or
building. It helps to elevate the woodpiles off the
ground (two 2 x 4’s running lengthwise beneath the
woodpile works well). This allows air to flow under the
bottom logs. Wood that is kept outdoors, either covered
with a tarp, or not covered at all, will not burn well until it
has been in an enclose space for one to two months.
MAINTENANCE
FIREBRICK
The firebrick should be inspected periodically and re-
placed if damaged (crumbling or excessively cracked).
SMALL AREA PAINT TOUCH-UP
The stove body is painted with a quality high-
temperature stove paint. Use only model TSPK-B Stove
Paint, Catalog # 70K99. Do not touch-up your stove
with any other paint.
Using one small piece of 320 grit sand paper and lightly
sand the blemish so that the edges are “feathered” or
smooth to the touch between the painted and bare sur-
faces. Do not let the sand paper gum up with paint, as
this will cause scratches on the metal surface. If there
are any scratches, use 600 grit sandpaper instead.
Mask off surfaces you do not want painted. Paint lightly
over the bare surface first as this will act as an under-
coat. Then paint over a larger area in smooth even
strokes to blend.
See Break-In Period on page 16 for information on
curing the paint.
CLEANING BLOWER INTAKE
If an optional blower kit (catalog #14M22) is installed,
the blower air intake requires cleaning at least once a
year to remove lint, dust, etc. If there are pets in the
dwelling, the intake should be cleaned at least twice a
year.
ASH REMOVAL AND DISPOSAL
CAUTION: MAKE SURE THAT THE FIRE IS OUT
AND THE STOVE IS COLD BEFORE REMOVING
ASHES! NEVER BURN YOUR STOVE WITH THE
ASH DRAWER OPEN OR UNSECURED!
Ashes can hold live embers for several days, and must
be disposed of with care.
Scrape ashes from the firebox through the grate into the
ash drawer. After emptying, clean and replace the ash
drawer and tighten the securing knobs.
NEVER place ashes in a cardboard box or any other
combustible receptacle.
Proper Disposal of Ashes:
Ashes should be placed in a metal container with a tight
fitting lid. The closed container of ashes should be
placed on a noncombustible floor or on the ground, well
away from all combustible materials, pending final dis-
posal. If the ashes are disposed of by burial in soil or
other wise locally dispersed, they should be retained in
the closed container until all cinders have thoroughly
cooled.
Ash
Drawer

MAINTENANCE
PAGE 19
DOOR / GLASS GASKET AND ASH DRAWER GAS-
KET
A 3/4" (19 mm) spun fiberglass gasket provides the seal
around the fuel door and a 1/8” (3.2 mm) x 1” (25.4 mm)
flat woven gasket glass provides the seal around the
glass. A ½” (13 mm) flat fiberglass gasket provides the
seal around the ash drawer. Should these gaskets be-
come frayed or damaged, they should be replaced with
the same size and type as the original gasket. Contact
your dealer for ordering. Use high temperature silicone
sealer as an adhesive for the fuel door gasket. The
glass and ash drawer gaskets have self-adhesive back-
ing.
WARNING: THE GASKETS MUST BE KEPT IN GOOD
CONDITION. DO NOT LEAVE THE STOVE BURNING
WITH THE DOOR OR ASH DRAWER OPEN OR AJAR.
THIS WILL CAUSE EXCESSIVE HEAT BUILD UP IN THE
UNIT AND COULD IGNITE SURROUNDING COMBUSTI-
BLES AS WELL AS DAMAGE THE STOVE BY OVERFIR-
ING IT. OVERFIRING IS A CONDITION WHERE EXCES-
SIVE TEMPERATURES ARE REACHED, BEYOND THE
DESIGN CAPABILITIES OF THE STOVE (SUCH DAMAGE
IS NOT COVERED BY THE MANUFACTURER'S WAR-
RANTY).
SERVICING GLASS
CAUTION: BE CAREFUL NOT TO ABUSE THE DOOR
ASSEMBLY BY STRIKING OR SLAMMING IT. IF THE
DOOR ASSEMBLY OR GLASS IS BROKEN OR DAM-
AGED, THEY MUST BE REPLACED BEFORE HEATER
CAN BE SAFELY OPERATED. USE ONLY COMPO-
NENTS PROVIDED BY THE MANUFACTURER AS
REPLACEMENT PARTS.
Cleaning Glass: Ensure stove is cold prior to cleaning glass.
A commercial glass cleaner designed for stoves is recom-
mended. Do not use abrasive cleaners.
Replacing Glass:
1. Remove door from stove by lifting door up and off
hinge pins: Place the door on a flat protected (towel)
clean flat surface with the inside of the door facing up.
Remove the glass clips (by removing screws holding
clips), then carefully remove broken glass one piece at
a time (protective gloves are recommended).
2. Clean area where the glass with gasket will be in-
stalled.
3. Install new glass with gasket (use only factory 5 mm
glass with glass channel gasket. Do not substitute).
Carefully reinstall glass clips. Be very careful not to
overtighten screws.
4. Reinstall door.
CREOSOTE FORMATION AND NEED FOR REMOVAL
What is Creosote - When wood is burned slowly, it pro-
duces tar and other organic vapors, which combine with
expelled moisture to form creosote. The creosote vapors
condense in the relatively cool chimney flue of a slow-
burning fire. As a result, creosote residue accumulates on
the flue lining. When ignited this creosote makes an ex-
tremely hot fire. Also, creosote deposits tend to form in
long runs of venting where gases become too cool prior to
exhausting. Note: Single wall pipe cools rapidly, there-
fore installations using this type of flue are more suscepti-
ble to creosote deposits.
To inhibit the build up of creosote, adjust the primary air
control to a medium-high or high setting for a 10-minute
period each day. Do not attempt to burn out heavy creo-
sote accumulations in this manner. This must be re-
moved from the chimney by scraping or brushing to re-
duce the risk of a chimney fire.
Burn Approved Fuel Only - This stove is approved for
burning dry seasoned natural wood only. Using green
or inadequately seasoned wood may increase creosote
buildup.
Inspection Frequency - The chimney connector and
chimney should be inspected at least twice monthly
during the heating season to determine if a creosote
buildup has occurred. If creosote has accumulated it
should be removed to reduce the risk of a chimney fire.
Cleaning - Remove the catalytic combustor and open
the bypass damper prior to having your chimney
cleaned (should be done by a qualified chimney
sweep). See Maintenance Section, Catalytic Combus-
tor, page 20 for instructions on removing catalytic com-
bustor.
IMPORTANT: Make sure the bypass damper is in
the open position prior to chimney cleaning.
In the event of a chimney fire - Make sure the fuel door
is securely closed. Adjust the primary air control to the
lowest (most closed) setting. Call the fire department im-
mediately. After a chimney fire, the complete chimney
system should be checked by a qualified technician be-
fore further use.
Consult your dealer for suggestions on proper chimney
care. Contact your local municipal or provincial fire author-
ity for information on how to handle a chimney fire. Have a
clearly understood plan for handling a chimney fire.

MAINTENANCE
PAGE 20
CATALYST REPLACEMENT
The normal expected life of a catalyst (catalytic com-
bustor) is 10,000 to 12,000 hours if the appliance is op-
erated correctly and proper fuels are used. If the cata-
lyst has been deactivated, it should be replaced. Symp-
toms of deactivation include – noticeably darker smoke
exiting chimney and less heat output. If these symp-
toms remain after normal maintenance or a major
cleaning (see Catalytic Combustor on this page for
cleaning instructions), the catalyst, p/n 14000 will re-
quire replacement. Also, if the catalyst is broken and /
or missing large pieces, it should be replaced.
Note: The catalyst does not need to be glowing to be
working. It will glow at times, but it can work very effec-
tively at temperatures well below the 1000°F level (at
which it will begin to glow).
Stove Operation if Catalyst Is Deactivated – It is safe
to operate the appliance temporarily with a deactivated
catalyst (although it will be out of compliance with EPA
certification requirements). To operate, follow normal
lighting and refueling procedures as outlined in this
manual with one of the following exceptions.
• During start-up, disregard catalytic temperature
probe reading to determine when to close bypass
damper control. Instead allow 20-25 minutes, then
close the bypass damper control.
• During refueling, disregard catalytic temperature
probe reading to determine when to close bypass
damper control. Instead allow 3-5 minutes after re-
fueling, then close the bypass damper control.
CATALYTIC COMBUSTOR
This appliance has been designed with a catalytic com-
bustor, which will improve its overall performance. Re-
moving the combustor assembly for cleaning and rein-
stallation is simple and convenient. Cleaning the com-
bustor helps reduce buildup of ash and retarding chemi-
cals. To clean the combustor, a soft brush, vacuum
cleaner, or pipe cleaner may be used.
Cleaning the combustor once a year, preferably when
your flue system is serviced, is sufficient for most users.
Reinstall the combustor according to the following in-
structions.
The catalytic activity and effectiveness of a two to three
year old combustor can be improved by following this
Major Cleaning Procedure - Soak the combustor in a
hot cleaning solution of a 50/50 mixture of white vinegar
and distilled water for 30 minutes. Then rinse by soak-
ing in hot distilled water. After 15 minutes, remove the
combustor from the rinse water and gently shake out
excess water. It is unlikely that you will notice a visible
difference in the combustor after this cleaning proce-
dure. The combustor unit is fragile in comparison to the
rest of the stove, so handle with care.
1. Place the combustor on the tunnel baffle as shown
in illustration (ceramic honeycomb to the back and
louvered slots to the front). Push it back into the tun-
nel baffle until it hits the positioning stops. Make sure
it is sitting flat against the bottom and the sides so
that it does not tilt forward and jump the positioning
stops.
2. Position combustor clip over the middle of the sec-
ondary air tube as illustrated. Make sure that one of
the holes in the secondary air tube is centered in the
½” (13 mm) hole on the clip. You can feel with your
fingertip.
3. Tighten screw snugly, but do not over-tighten or you
may spread the clip apart.
Side Cut-Away View of Firebox
Secondary
Air Tube
Use 7/16” Socket. Tighten
Snug (Do Not Overtighten)
Damper
Door
Positioning
Stops
Tunnel
Baffle
Catalytic
Combustor
Catalytic
Combustor
Retainer Clip
Retainer
Clip
Setscrew
Secondary
Air Tube