Lennox MPDR-3328CPE User manual

1
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
HOMEOWNER'S CARE AND
OPERATION INSTRUCTIONS
VENTED GAS FIREPLACE HEATERS - DIRECT VENT MODELS
P/N 875,014M REV. K 03/2007
RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE
FOR YOUR SAFETY: Do not store or use gasoline
or other flammable vapors or liquids in the vicin-
ity of this or any other appliance.
FOR YOUR SAFETY: What to do if you smell gas:
• DO NOT light any appliance.
• DO NOT touch any electrical switches.
• DO NOT use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone.
Follow your gas suppliers instructions.
• Ifyourgassuppliercannotbereached,callthe
fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
POURVOTRESÉCURITÉ: Nepasentreposerniutiliser
d'essencenid'autrevapeursouliquidesinflammables
dans le voisinage de cet appareil ou de tout autre
appareil.
POUR VOTRE SÉCURITÉ: Que faire si vous sentez une
odeur de gaz:
• Ne pas tenter d'allumer d'appareil.
• Netouchezàaucuninterrupteur. Nepasvousservir
des téléphones se trouvant dans le batiment où
vous vous trouvez.
• Evacuez la piéce, le bâtiment ou la zone.
• Appelez immédiatement votre fournisseur de gaz
depuis un voisin. Suivez les instructions du
fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service dos incendies.
L'installationetservicedoitêtreexécutéparunqualifié
installeur, agence de service ou le fournisseur de gaz.
DIRECT-VENT
MPD-33/35/40/45 SERIES
MODELS
OTL Report No. 116-F-13-4
sledoMtlovilliMsledoMcinortcelE
MNC8233-TDPMMNC5304-DPMENC8233-TDPMENC5304-DPM
MPC8233-TDPMMPC5304-DPMEPC8233-TDPMEPC5304-DPM
MNC8233-RDPMMNC0454-DPMENC8233-RDPMENC0454-DPM
MPC8233-RDPMMPC0454-DPMEPC8233-RDPMEPC0454-DPM
MNC0353-DPMENC0353-DPM
MPC0353-DPMEPC0353-DPM
A French manual is available upon request. Order Form Number
875,014CF.
Ce manuel d’installation est disponible en francais, simplement en
faire la demande. Numéro de la pièce 875,014CF.
WARNING:IFTHEINFORMATIONINTHISMANUAL
IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLO-
SION MAY RESULT CAUSING PROPERTY DAM-
AGE, PERSONAL INJURY OR LOSS OF LIFE. AVERTISSEMENT: ASSUREZ-VOUS DE BIEN SUIVRE
LESINSTRUCTIONSDONNÉDANSCETTENOTICEPOUR
RÉDUIRE AU MINIMUM LE RISQUE D'INCENDIE OU
POUR ÉVITER TOUT DOMMAGE MATÉRIEL, TOUTE
BLESSURE OU LA MORT.
WARNINGS
•Hot! Do not touch! The glass and
surfaces of this appliance will be hot
during operation and will retain heat
for a while after shutting off the appli-
ance. Severe burns may result.
•Carefully supervise children in the
same room as appliance.
•If small children are present in the home, it is
recommended that this appliance be fitted with
a screen door or screen panel kit. See
Page 12
for ordering information.

2NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Theseappliances aredesignedto operateon
natural or propane gas only.
Input of millivolt models is variable. These
rates are shown in the following tables:
CONGRATULATIONS!
InselectingthisLENNOXDirect-VentGasApplianceyouhavechosenthefinestandmost
dependable fireplace to be found anywhere. A beautiful, prestigious, alternative to a
woodburningfireplace. WelcometoaFamilyoftensofthousandsofsatisfiedLENNOX
Fireplace Owners.
Please read and carefully follow all of the instructions found in this manual. Please pay
special attention to the safety instructions provided in this manual. The Homeowner's
Care and Operation Instructions included here will assure that you have many years of
dependable and enjoyable service from your LENNOX product.
INTRODUCTION
The Fireplace models covered in this manual
areDirect-Ventsealedcombustionventedgas
fireplace heaters designed for residential ap-
plication. Direct-Ventappliancesoperatewith
the combustion chamber completely isolated
from the inside atmosphere. All air for com-
bustion is brought in from the outside and
exhaust gases are vented through the same
direct vent, vent system.
GENERAL INFORMATION
Note: Installation and repair should be per-
formedbyaqualifiedserviceperson.Theappli-
ance should be inspected annually by a quali-
fied professional service technician. More fre-
quent inspections and cleanings may be re-
quired due to excessive lint from carpeting,
bedding material, etc. It is imperative that the
control compartment, burners and circulating
airpassagewaysoftheappliancebekeptclean.
S'assurer que le brùleur et le compartiment
des commandes sont propres. Voir les in-
structions d'installation et d'utilisation qui
accompagnent l'appareil.
Provideadequateclearancesaroundairopen-
ings and adequate accessibility clearance for
service and proper operation. Never obstruct
the front openings of the appliance.
Duetohightemperaturestheapplianceshould
be located out of traffic and away from furni-
ture and draperies. Locate furniture and win-
dow coverings accordingly.
The millivolt appliances are designed to oper-
ateoneithernaturalorpropanegas.Amillivolt
gas control valve with piezo ignition system
provides safe, efficient operation. External
electrical power is required to operate the
optional electrically powered components if
installed. Electrical power must be wired
during appliance installation.
The electronic appliances are designed to op-
erate on either natural or propane gas. An
electronic intermittent pilot system provides
safe, efficient operation. External electrical
power is required to operate these units.
TheseappliancescomplywithNationalSafety
Standards and are tested and listed by Omni-
Test Laboratories (Report No. 116-F-13-4) to
ANSI Z21.88-2000 (in Canada, CSA-2.33-
2000), and CAN/CGA-2.17-M91 in both USA
and Canada, as vented gas fireplace heaters.
Installation must conform to local codes. In
the absence of local codes, installation must
comply with the current National Fuel Gas
Code,ANSIZ223.1(NFPA54).(InCanada,the
currentCAN/CGAB149installationcode.) Elec-
tricalwiringmust complywithlocalcodes. In
the absence of local codes, installation must
be in accordance with the National Electrical
Code, NFPA 70 - (latest edition). (In Canada,
thecurrentCSAC22.1CanadianElectricCode.)
DO NOT ATTEMPT TO ALTER OR MODIFY
THE CONSTRUCTION OF THE APPLIANCE OR ITS
COMPONENTS. ANY MODIFICATION OR ALTER-
ATION MAY VOID THE WARRANTY,
CERTIFICATION AND LISTINGS OF THIS UNIT.
TABLE OF CONTENTS
Introduction..................................... page 2
General Information......................... page 2
Operation/Care of Your Appliance.... page 3
Gas Controls/Compartment Access . page 3
Variable Flame Adjustment .............. page 4
Maintenance Schedule..................... page 5
Maintenance .................................... page 6
Glass Cleaning................................. page 6
Front Glass Enclosure Panel,
Removal and Installation ............... page 6
Burner Adjustments......................... page 6
Flame Appearance and Sooting ....... page 6
Adjustment ...................................... page 7
Log Placement................................. page 7
Rockwool Placement ....................... page 7
Vermiculite Placement..................... page 7
Volcanic Stone Placement ............... page 7
Millivolt Appliance Checkout............ page 7
Electronic Appliance Checkout......... page 8
Wiring Diagrams.............................. page 9
Warranty.......................................... page 9
Replacement Parts .......................... page 9
Product Reference Information ....... page 9
Accessory Components................... page 11
Lighting Instructions – Millivolt....... page 16
Lighting Instructions – Electronic.... page 18
Troubleshooting Guide – Millivolt ..... page 20
Troubleshooting Guide – Electronic .. page 21
Replacement Parts List..................... page 22
htiwsledoMtlovilliM evlaVsaGdetaludoM-yllaunaM saGlarutaN
seireSledoM)H/UTB(etartupnI
8233-TDPM 8233-RDPM 005,71ot007,11
0353-DPM000,02ot008,21
5304-DPM000,72ot005,81
0454-DPM000,92ot005,02
WARNING: THESE FIREPLACES ARE
VENTED HEATERS. DO NOT BURN
WOOD OR OTHER MATERIAL IN THESE
APPLIANCES.
WARNING: IMPROPERINSTALLATION,
ADJUSTMENT, ALTERATION, SERVICE
ORMAINTENANCE CAN CAUSE INJURY
OR PROPERTY DAMAGE. REFER TO
THIS MANUAL. FOR ASSISTANCE OR
ADDITIONAL INFORMATION CONSULT
A QUALIFIED INSTALLER, SERVICE
AGENCY OR THE GAS SUPPLIER.
WARNING: ELECTRONIC MODELS OF
THESE APPLIANCES ARE EQUIPPED
WITH A THREE-PRONG (GROUNDING)
PLUG UTILIZED IN CONNECTING THE
ELECTRONIC COMPONENTS TO THE
JUNCTION BOX IN THE LOWER COM-
PARTMENT. THIS GROUNDING PLUG
PROVIDES PROTECTION AGAINST
SHOCK HAZARD AND SHOULD BE
PLUGGED DIRECTLY INTO THE PROP-
ERLY GROUNDED THREE-PRONG RE-
CEPTACLE. DO NOT CUT OR REMOVE
THE GROUNDING PRONG FROM THE
PLUG.

3
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Maximum manifold pressure is 3.5 in. w.c.
(0.87kPa)for natural gasand10in. w.c.(2.49
kPa) for LP/Propane gas.
Donotusetheseappliancesifanyparthasbeen
under water. Immediately call a qualified, pro-
fessional service technician to inspect the ap-
pliance and to replace any parts of the control
system and any gas control which have been
under water.
Ne pas se servir de cet appareil s'il a été plongé
dansl'eau,complètementouenpartie. Appeler
untechnicienqualifiépourinspecterl'appareilet
remplacertoutepartiedusystèmedecontrôleet
toutecommandequiontétéplongésdansl'leau.
Test gage connections are provided on the
front of the millivolt gas control valve (identi-
fied OUT for the manifold side and IN for inlet
pressure. A ¹⁄₈" NPT test gage connection is
provided on the electronic gas control valve
adjacent to the outlet to the main burner.
OPERATION AND CARE OF YOUR
APPLIANCE
Applianceoperationmaybecontrolledthrough
a remotely located optional wall switch. Sepa-
rateswitchesmayprovideindependentcontrol
for the remote controlled fireplace operation
(optional equipment).
In lieu of remote or remote wall switch opera-
tion, the appliance must be operated directly
throughthecontrolslocatedonthefrontofthe
valve located within the control compartment
which is located behind the control compart-
ment access panel below the appliance front
glass enclosure panel. See
Figure 1.
Gas Controls/Control Compartment
Access
The gas controls can be found behind the
control compartment access panel.
Toopenthecontrolcompartmentaccesspanel,
actuate the spring-loaded magnetic catches
securing the panel, by gently depressing the
outertopcorners of thepaneluntil the catches
"pop"thedoorfree,allowingittoswingoutand
down to open.
Operationofmillivoltandelectronicgascon-
trol systems are different. Before lighting
and operating your appliance determine if
you have a millivolt or electronic appliance.
See
Figure 1 on page 4 for access to the
control compartment.
Millivolt appliances will be fitted with the gas
controlvalveshownin
Figure3 (SIT)or Figure
4 (Honeywell) on page 4 . Appliances with
electronic systems will be fitted with the elec-
tronic valve shown in
Figure 2 on page 4 .
Familiarize yourself with the gas control valve
that your appliance uses.
Thefollowingtableshowstheunits'orificesize
for the elevations indicated.
Electronic Models -
Electronic models have a fixed rate gas valve.
Input of electronic models is shown in the
following table:
htiwsledoMtlovilliM evlaVsaGdetaludoM-yllaunaM saGenaporP
seireSledoM)H/UTB(etartupnI
8233-TDPM 8233-RDPM 005,71ot000,41
0353-DPM000,02ot002,51
5304-DPM000,72ot005,12
0454-DPM000,92ot005,22
evlaVsaGetaR-dexiFhtiwsledoMcinortcelE
saGenaporPdnalarutaN
seireSledoM)H/UTB(etartupnI
8233-TDPM 8233-RDPM 005,71
0353-DPM000,02
5304-DPM000,72
0454-DPM000,92
ledoM seireS
ezisecifirO noitavelE teeF )sretem(
.taN.porP
8233-TDPM 8233-RDPM 54#hcni840.0
0054-0 )0731-0(
0353-DPM44#55#
5304-DPM73#hcni260.0
0454-DPM63#25#
Millivolt Appliances -
Tolightmillivoltappliancesrefertothedetailed
lighting instructions found on
page 12 (En-
glish) and page 13
(French) . Millivolt appli-
ance lighting instructions may also be found
on the pull-out lighting instruction labels at-
tached to the gas control valve.
WARNING: DO NOT PLACE CLOTH-
ING OR OTHER FLAMMABLE MATERI-
ALS ON OR NEAR THIS APPLIANCE.
AVERTISSEMENT: SURVEILLER LES
ENFANTS. GARDER LES VÊTEMENTS,
LESMEUBLES,L'ESSENCEOUAUTRES
LIQUIDES ÀVAPEUR INFLAMMABLES
LOIN DE L'APPAREIL.
Minimuminletgaspressuretotheseappliances
is5.0 incheswatercolumn(1.24kPa)fornatural
gas and 11 inches water column (2.74 kPa) for
propane for the purpose of input adjustment.
Maximum inlet gas supply pressure to these
appliances is 10.5 inches water column (2.61
kPa) for natural gas and 13.0 inches water
column (3.23 kPa) for propane.
The appliance must be isolated from the gas
supply piping system (by closing its individual
manualshut-offvalve)duringanypressuretest-
ing of the gas supply piping system at test
pressuresequaltoorlessthan¹⁄₂ psig(3.5kPa).
The appliance and its individual shut-off valve
must be disconnected from the gas supply
piping system during any pressure testing of
that system at pressures in excess of ¹⁄₂ psig
(3.5 kPa).
These appliances must not be connected to a
chimney or flue serving a separate solid fuel
burning appliance.
Any safety guard or screen removed for ser-
vicingtheappliance mustbereplaced priorto
operating the appliance.
Carbon Monoxide Poisoning: Early signs of
carbon monoxide poisoning are similar to the
fluwithheadaches,dizzinessand/ornausea.If
youhave these signs, obtain freshair immedi-
ately. Turn off the gas supply to the appliance
and have it serviced by a qualified profes-
sional, as it may not be operating correctly.
WARNING: FAILURE TO COMPLY WITH
THEINSTALLATIONANDOPERATINGIN-
STRUCTIONSPROVIDED IN THIS DOCU-
MENT WILL RESULT IN AN IMPROP-
ERLY INSTALLED AND OPERATING AP-
PLIANCE,VOIDINGITSWARRANTY. ANY
CHANGE TO THIS APPLIANCE AND/OR
ITSOPERATINGCONTROLSISDANGER-
OUS. IMPROPER INSTALLATION OR
USE OF THIS APPLIANCE CAN CAUSE
SERIOUSINJURYORDEATHFROMFIRE,
BURNS, EXPLOSION OR CARBON MON-
OXIDE POISONING.
WARNING: CHILDREN AND ADULTS
SHOULD BE ALERTED TO THE HAZARDS
OFHIGHSURFACETEMPERATURES.USE
CAUTION AROUND THE APPLIANCE TO
AVOID BURNS OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD BE CARE-
FULLY SUPERVISED WHEN THEY ARE IN
THE SAME ROOM AS THE APPLIANCE.

4NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Electronic Appliances -
To light electronic appliances refer to the de-
tailed lighting instructions found in both En-
glishand French on
pages 14 and 15 of these
instructionsrespectively.Electronicappliance
lighting instructions may also be found on
the pull out lighting instruction labels at-
tached to the gas control valve.
Honeywell Electronic Gas Valve
2. Whenlitforthefirsttime,thisappliancewill
emit a slight odor for an hour or two. This is
due to the “burn-in” of internal paints and
lubricantsusedinthemanufacturingprocess.
3. Keep lower control compartment clean by
vacuuming or brushing at least twice a year.
Morefrequentcleaningmayberequireddueto
excessive lint from carpeting, bedding materi-
als, etc. It is important that control compart-
ments, burners and circulating air passage-
waysoftheappliancebekeptcleanandclearof
obstructions of venting and combustion air.
4. Always turn off gas to the pilot (millivolt
appliances) before cleaning. Before re-light-
ing, refer to the lighting instructions in this
manual.Instructions arealso foundon apull-
outpanellocatedontheflooroftheappliance.
5. Always keep the appliance area clear and
freefromcombustiblematerials,gasolineand
other flammable liquids.
6. Remember,Millivoltappliances have acon-
tinuous burning pilot flame. Exercise caution
whenusingproductswithcombustiblevapors.
Honeywell Millivolt Gas Valve
Figure 4
Figure 3
H
I
L
O
W
TPTH TP TH
P
I
L
O
T
P
I
L
O
T
O
N
it
O
F
F
Variable Flame Height Adjustment
Manifold Pressure Port
Inlet Pressure Port
Main Gas
Control Knob
Piezo Ignitor
IN OUT
Piezo Ignitor
Optional Burner ON/OFF
Rocker Switch Location Factory-Installed Blower ON/OFF
Rocker Switch Location
Main Gas
Control Knob
Variable Flame
Height Adjustment
Piezo Ignitor
O
N
O
F
F
P
I
L
O
T
L
O
H
I
Manifold
Pressure Port Inlet
Pressure Port
Optional ON/OFF Rocker Switch
Location (One of Two Places)
Piezo Ignitor
Optional Burner ON/OFF
Rocker Switch Location
SIT Millivolt Gas Valve
ON/OFF Switch
Electronic
Gas Control
Valve
Inlet
Pressure
Port
Manifold Pressure Port
OFF
IN
PSI
ON
CONTROL
IGNITER
Figure 2
If your electronic appliance is equipped with
anoptionalremotewallswitchorremotecon-
trol kit the appliance main burner may be
turned on and off with the wall switch or
remote control.
If your electronic appliance is not equipped
witha wallswitch orremote control,the main
burnermustbe turnedoffand onwiththe gas
control switch. Toggle the switch from ON to
OFF to operate the main burner .
Variable Flame Height Adjustment
( Millivolt Appliances only)
1. All Millivolt appliances are equipped with a
variable gas control valve. Flame height for
thesemodelsmaybeadjustedthrougharange
between fixed low and high settings, alter-
nately, while the appliance is in operation.
Adjusttheflameheightasdesiredafterlighting
the appliance by rotating the variable adjust-
ment control knob located on the front of the
valve
(refer to Figure 3 - SIT, 4 - Honeywell) .
Piezo Ignitor
Drop Down
Control
Compartment
Access Panel
SIT Gas Valve
Honeywell
Gas Valve
Figure 1
Sit and Honeywell Millivolt Gas Valve
Showing Piezo Ignitor Location (Each Unit is
Equipped with Only One of these Gas Valves)
See
Figure 2 (SIT), 3 (Honeywell) for the
location of the piezo ignitor.
Millivoltappliancesmaybefittedwithanoptional
burner ON/OFF Rocker Switch. The optional ON/
OFFRockerswitchwill be installedinthe bracket
justbeneath thegas control valve. Once thepilot
is lit, the ON/OFF rocker switch will control the
applianceON/OFF operation. To operate: Toggle
the switch between its ON and OFF positions.
If your millivolt appliance is equipped with an
optional remote wall switch or remote control
kitandthepilotislit,theappliancemainburner
maybeturnedonandoffwiththewallswitchor
remote control.

5
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Periodically (After the Burning Season)
Maintenance Task Accomplishing Person Procedure
Cleaning Firebox Interior
Check Flame Patterns and Flame Height
Checking Vent System
Cleaning Front Glass Enclosure Panel
Homeowner
Homeowner
Homeowner
Homeowner
Carefully remove logs, Rockwool and volca-
nic stone if used. Vacuum out interior of the
firebox. Clean firebox walls and log grate.
Replace logs, Rockwool and volcanic stone
as detailed in this manual.
Maintenance Task Accomplishing Person Procedure
Inspecting/Cleaning Burner, Logs
and Controls
Check Flame Patterns and Flame Height
Inspecting/Cleaning Pilot and Burner
Checking Vent System
Appliance Checkout
Replacing Rockwool Ember Materials
Qualified Service Technician
Qualified Service Technician
Qualified Service Technician
Qualified Service Technician
Qualified Service Technician
Homeowner/Qualified Services Technician
Inspectvalveandensureitisproperlyoperating.
Check piping for leaks. Vacuum the control
compartment, fireplace logs and burner area.
Referto
Figure 7 (MPD-3328), 8 (MPD-3530)
or 9 (MPD-4035, MPD-4540) on page 7 and
verify the flame pattern and height displayed
by the appliance conforms to the picture.
Flames must not impinge on the logs.
Referto Figure 10 (SITMillivolt), Figure 11
(Honeywell Millivolt) or Figure 12 (Elec-
tronic) on page 8 . Remove any surface
build-uponpilotandburnerassembly. Wipe
thepilotnozzles,ignitor/flamerodandhood.
Ensure the pilot flame engulfs the flame
sensor as shown.
Inspect the vent system at the top and at the
base(withinthe firebox) forsignsofblockage
orobstruction. Look for anysigns of disloca-
tion of the vent components.
Perform the appropriate appliance checkout
procedure detailed in this manual.
Remove old ember materials and vacuum the
screenedrockwoolplacementarea. Placenew
rockwool as described in this document.
Maintenance Schedule
Annually (Before the onset of the Burning Season)
Clean as necessary following the directions
providedinthismanual. DO NOT TOUCH OR
ATTEMPT TO CLEAN GLASS WHILE HOT.
Inspect the vent system at the top and at the
base (within the firebox) for signs of block-
age or obstruction. Look for any signs of
dislocation of the vent components.
Referto
Figure 7 (MPD-3328), 8 (MPD-3530)
or 9 (MPD-4035, MPD-4540) on page 7 and
verifytheflamepatternandheightdisplayedby
the appliance conforms to the picture. Flames
must not impinge on the logs.

6NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Front Glass Enclosure Panel, Removal
and Installation.
To install the front glass enclosure panel,
proceed as follows:
1. Retrieve the glass door frame. Visually
inspect the gasket on the backside of the
panel. Thegasket surface mustbe clean, free
of irregularities and seated firmly.
2. Position the door frame in front of the
firebox opening and engage the top flange
over the lip at the top of the firebox opening.
3. Swingthedoordownandback. Ensurethe
gasket seats evenly as the door draws shut.
Engage the Vee-flange at the bottom of the
door with the latches and close the latches to
secure the door.
4. Reinstallthetoplouverassemblyorradiant
panel.
Burner Adjustments
The following paragraphs address burner ad-
justment concerns and procedures.
Flame Appearance and Sooting
Proper flame appearance is a matter of taste.
Generallymostpeoplepreferthewarmglowof
a yellow to orange flame. Appliances operated
withair shutteropenings thatare toolarge will
exhibit flames that are blue and transparent.
These weak, blue and transparent flames are
termedanemic.Iftheairshutteropeningistoo
small sooting may develop.
These are direct-vent appliances. They are
designed to operate only with the front glass
enclosure panel properly installed. Generally,
the glass enclosure panel should not be re-
moved except to gain access to the compo-
nents within the firebox, and the appliance
may only be operated without the front glass
enclosurepanel inplace forvery brief periods
of time during initial appliance checkout and
adjustment.
See Figure 5 and remove the front glass
enclosure panel as follows:
1. Removethe top louverassembly or radiant
panel.
2. Open the hinged drop-down control com-
partment access panel.
3. Locate the two (2) latches at the top of the
controlcompartmentanddisengagethemfrom
the floor frame bottom Vee-flange, pulling
down on their handles to open them.
Figure 5
During this appliance checkout and adjust-
ment period, a potential safety hazard exists
- EXERCISE EXTREME CAUTION to prevent
the occurrence of any burn injuries from the
exposed flames or hot surfaces.
Alsonote, that whilethe front glassenclosure
panel is removed, the flame appearance will
appear to be smaller than normal.
CAUTION: DO NOT ATTEMPT TO TOUCH THE
FRONT ENCLOSURE GLASS WITH YOUR
HANDS WHILE THE FIREPLACE IS IN USE.
Note: Clean glass after first two weeks of
operation.
Glass Cleaning
It will be necessary to clean the glass periodi-
cally. Duringstart-upit is normalforconden-
sationto form on the inside of the glass. This
can cause lint, dust and other airborne par-
ticles to cling to the glass surface. Also initial
paint curing may deposit a slight film on the
glass. It is therefore recommended that the
glassbecleanedtwoorthreetimeswithanon-
ammonia household cleaner and warm water
(agasfireplaceglasscleanerisrecommended).
After that the glass should be cleaned two or
three times during each heating season, de-
pending on the circumstances present.
WARNING: DO NOT USE ABRASIVE
CLEANERS. NEVER CLEAN THE GLASS
WHEN IT IS HOT.
WARNING: NEVER OPERATE THE AP-
PLIANCE WITHOUT THE GLASS EN-
CLOSURE PANEL IN PLACE AND SE-
CURE. DO NOT OPERATE APPLIANCE
WITH THE FRONT GLASS PANEL
CRACKED, BROKEN OR MISSING. RE-
PLACEMENT PANELS ARE AVAILABLE
THROUGH YOUR LOCAL LENNOX
DEALERANDMUSTBEINSTALLEDBYA
LICENSED OR QUALIFIED SERVICE
TECHNICIAN.
WARNING: HANDLE THE GLASS
WITH EXTREME CARE! DO NOT
STRIKE DOOR. TEMPERED GLASS
IS SUSCEPTIBLE TO DAMAGE
(SCRATCHES, FOR EXAMPLE) –
HANDLE GLASS DOOR (GLASS EN-
CLOSURE PANEL) GENTLY WHILE
REINSTALLING IT.
WARNING:NONOTATTEMPTTOSUB-
STITUTE THE MATERIALS USED ON
THIS DOOR, OR REPLACE CRACKED
OR BROKEN GLASS WITH ANY MATE-
RIALSOTHER THAN THOSEPROVIDED
BYTHEAPPLIANCEMANUFACTURER.
THE GLASS DOOR OF THIS APPLIANCE
MUST ONLY BE REPLACED AS A COM-
PLETE UNIT AS PROVIDED BY THE
MANUFACTURER. DO NOT ATTEMPT
TO REPLACE BROKEN, CRACKED OR
CHIPPED GLASS SEPARATELY.
Latch
Latch
Glass Door
Firebox Floor
Bottom Vee-flange
Door Frame
Top Flange
Door Frame
4. Swingthebottomofthedooroutandraise
itslightlytoliftthetopflangeofthedoorframe
away from the appliance.
Maintenance
The appliance and venting system should be
thoroughly inspected before initial use and at
least annually by a qualified service techni-
cian.However,morefrequentperiodicinspec-
tions and cleanings should be performed by
the homeowner. Homeowner must contact a
qualified service technician at once if any
abnormal condition is observed.
Refer to the maintenance schedule for mainte-
nancetasks,procedures,periodicityandbywhom
theyshouldbeperformed. Alwaysverifyproper
operation of the appliance after servicing.
IMPORTANT: TURN OFF GAS AND ANY
ELECTRICAL POWER BEFORE SERVICING
THE APPLIANCE.

7
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Log Placement
ENSURE THAT THE FRONT GLASS PANEL IS IN
PLACE AND SEALED DURING ADJUSTMENT.
Adjustment
CAUTION: THE ADJUSTMENT ROD AND
NEARBY APPLIANCE SURFACES ARE HOT.
EXERCISECAUTIONTOAVOIDINJURYWHILE
ADJUSTING FLAME APPEARANCE.
To adjust the flame, move the adjustment rod
(locatedin the lowercontrol area)up ordown
to increase or reduce the air shutter opening,
respectively.Initially, always position the air
shutter to the factory setting (the minimum
air opening position) as shown in Figure 6 .
This can be done by pulling the adjustment
rod all the way down. Allow the burner to
operate for at least 15 minutes. Observe the
flamecontinuously.Ifitappearsweakorsooty
aspreviously described,adjust the air shutter
by pushing or pulling on the adjustment rod
until the flame appearance is as desired.
Theadjustmentrodandassociatedadjustable
air shutter is patented technology. Flame ad-
justmentscanbemadequicklyandaccurately
totastewithouttheneedofdisassemblingthe
appliance and waiting for 30 minutes after
each adjustment.
Figure 6
sledoM saG epyT
RIAYROTCAF RETTUHS GNITTES )mm(sehcni
8233-TDPM .taN23/1)8.O(
.porP61/3)67.4(
8233-RDPM .taN23/1)8.O(
.porP61/3)67.4(
0353-DPM .taN23/1)8.O(
.porP61/3)67.4(
5304-DPM .taN8/1)2.3(
.porP2/1)31(
0454-DPM .taN8/1)2.3(
.porP2/1)31(
If the logs are properly positioned and sooting
conditions exist, the air shutter opening on the
mainburnertube shouldbe adjusted. Normally,
the more offsets in the vent system, the greater
theneedfortheairshutter to be openedfurther.
Glowing Embers (Rockwool) Placement
Refer to the detailed glowing embers place-
mentinstructionsprovided in theLOG PLACE-
MENT GUIDE accompanying this document.
Vermiculite and Decorative Volcanic Stone
Placement
Refer to the detailed vermiculite and decora-
tivevolcanicstoneplacementinstructionspro-
vided in the LOG PLACEMENT GUIDE accom-
panying this document.
Millivolt Appliance Checkout
Thepilotflameshould besteady,notlifting or
floating. Flame should be blue in color with
traces of orange at the outer edge.
The top ³⁄₈" (10 mm) at the pilot generator
(thermopile) and the top ¹⁄₈" min (tip) of the
quick drop out thermocouple should be en-
gulfed in the pilot flame. The flame should
project1"(25mm)beyondthehoodatallthree
ports
(see Figure 10 - SIT, and Figure 11 -
Honeywell, on page 8 ) .
To light the burner, refer to the lighting in-
structions on pages 12 and 13.
When satisfied that the appliance operates
properly, proceed to finish the installation.
Leave the control knob in “ON” position and
turnthe remote switch “OFF.” Close the lower
control compartment door.
Propane models may exhibit a flame pattern
that may candle or appear stringy. If this is
problematic or persists as the appliance is
continually operated, adjust the air shutter
closed as described in the previous para-
graphs. Operate the appliance for a period of
timeastheeffectdiminishes,ensuringthatthe
appliance does not develop sooty flames.
Sooting is indicated by black puffs developing
at the tips of very long orange flames. Sooting
results in black deposits forming on the logs,
appliance inside surfaces and on exterior sur-
faces adjacent to the vent termination.
Sooting is caused by incomplete combustion in
theflamesandalackofcombustionairentering
the air shutter opening. To achieve a warm
yellowtoorangeflamewithanorangebodythat
does not soot, the shutter opening must be
adjustedbetweenthesetwoextremes. Nosmoke
orsootshouldbepresent.Repositionthelogsif
the flames impinge on any of them.
WARNING: AIR SHUTTER ADJUST-
MENTSHOULDONLYBE PERFORMED
BYAQUALIFIEDPROFESSIONALSER-
VICE TECHNICIAN.
WARNING: LOGS GET VERY HOT AND
WILL REMAIN HOT UP TO ONE HOUR
AFTER GAS SUPPLY IS TURNED OFF.
HANDLEONLYWHENLOGSARECOOL.
TURN OFF ALL ELECTRICITY TO THE
APPLIANCE BEFORE YOU INSTALL
GRATE AND LOGS.
WARNING: THIS APPLIANCE IS NOT
MEANT TO BURN WOOD. ANY AT-
TEMPT TO DO SO COULD CAUSE IR-
REPARABLE DAMAGE TO YOUR AP-
PLIANCE AND PROVE HAZARDOUS TO
YOUR SAFETY.
WARNING: THESIZEANDPOSITION ON
THE LOG SET WAS ENGINEERED TO
GIVE YOUR APPLIANCE A SAFE, RELI-
ABLE AND ATTRACTIVE FLAME PAT-
TERN. ANY ATTEMPT TO USE A DIF-
FERENT LOG SET IN THE FIREPLACE
WILL VOID THE WARRANTY AND WILL
RESULTININCOMPLETECOMBUSTION,
SOOTING,ANDPOORFLAMEQUALITY.
Adjustment Rod
Up (Fully Open
Position)
Air Shutter
Venturi
Adjusting
Set Screw
Adjustment Rod Down
(minimum air
opening position)

8NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Electronic Appliance Checkout
Tolighttheburner,refertothelightinginstruc-
tions on page 14 and 15 . Ensure the ignitor
lightsthepilot.Thepilotflameshouldengulfthe
flame sensor as shown in Figure 12.
Figure 12
With proper care and maintenance, your ap-
pliance will provide many years of enjoy-
ment. If you should experience any problem,
firstrefertothetroubleshootingguideinthis
manual. If problem persists, contact your
Lennox distributor.
Figure 11
Figure 7 MPD-3328 MODEL
Carefully position the ceramic fiber logs and twigs over the burner as shown in Figures 7 (MPD-
3328), 8 (MPD-3530) or 9 (MPD-4035, MPD-4540)
. For more detailed placement instructions,
refer to the LOG PLACEMENT GUIDE accompanying this document.
Proper twig placement is critical to prevent sooting. Twigs should be placed in the gaps between
the flame peaks and should be positioned so that at no time they impinge the flames.
Figure 8 MPD-3530 MODEL
Figure 9 MPD-4035 AND MPD-4540 MODEL
Figure 10
¹⁄₈" Min
(3 mm)
Thermocouple
Ignitor Rod
Hood
³⁄₈" Min
(9 mm)
Thermopile
MILLIVOLT HONEYWELL
Pilot
Nozzels
ELECTRONIC
Proper Flame
Adjustment
Pilot
Nozzle
3/8 To 1/2 Inch
(9 mm to 13 mm)
Ground
Electrode
Flame Rod
Hot Surface
Igniter
SIT MILLIVOLT
Thermocouple
Hood Ignitor Rod
³⁄₈" Min
(9 mm)
Thermopile
Pilot
Nozzels

9
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
WIRING DIAGRAMS
Wiring diagrams are provided here for reference purposes only. This information is also provided on schematics attached directly to the appliance
on a pullout panel located within the control compartment.
CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER
AND DANGEROUS APPLIANCE OPERATION.
WARRANTY
Your gas appliance is covered by a limited
twentyyear warranty.Youwillfindacopyof
the warranty accompanying this manual.
Please read the warranty to be familiar with
its coverage.
Retainthismanual.Fileitwithyourotherdocu-
ments for future reference.
REPLACEMENT PARTS
Acompletepartslistisfoundattheendofthis
manual. Use only parts supplied from the
manufacturer.
Normally, all parts should be ordered through
yourLennoxdistributor ordealer.Parts will be
shipped at prevailing prices at time of order.
When ordering repair parts, always give the
following information:
PRODUCT REFERENCE INFORMATION
Werecommendthat you record thefollowingimportantinformationaboutyourfireplace. Please
contactyourLennoxdealerforanyquestionsorconcerns. ForthenumberofyournearestLennox
dealer, please call 1-800-9-LENNOX
Your Fireplace's Model Number _______________________________________
Your Fireplace's Serial Number ________________________________________
The Date On Which Your Fireplace Was Installed __________________________
The Type of Gas Your Fireplace Uses ___________________________________
Your Dealer's Name_________________________________________________
If you encounter any problems or have any
questions concerning the installation or appli-
cation of this system, please contact your dis-
tributor, or Lennox directly:
LENNOX HEARTH PRODUCTS
1110 West Taft Avenue
Orange, CA 92865
1. The model number of the appliance.
2. The serial number of the appliance.
3. The part number.
4. The description of the part.
5. The quantity required.
6. The installation date of the appliance.
SIT And Honeywell Millivolt Wiring Diagram
If any of the original wire as supplied must be replaced,
it must be replaced with Type AWM105°C –18 GA. wire.
Thermopile
TH
TP TH
TP
*TWIST WIRES “A”AND “B”TOGETHER TO OPERATE UNIT
SOLELY BY MANIPULATING THE GAS VALVE CONTROL KNOB;
OR CONNECT WIRES TO OPTIONAL ON/OFF SWITCH OR WALL
SWITCH OR THERMOSTAT TO OPERATE UNIT.
*OPTIONAL
ON/OFF SWITCH,
WALL SWITCH, THERMOSTAT
OR REMOTE CONTROL RECEIVER
AB
1. If any of the original wire as supplied must be replaced,
1. it must be replaced with Type AWM 105°C –18 GA. wire.
2. 120V, 60Hz –Less than 3 amps.
BK
Transf.
120 V.
24 V
Factory Wired Field Wired
BL
Electronic Wiring Diagram (Honeywell)
Showing the Blower Wiring for the Optional
FBK-100 and FBK-200 Kits
R
W
BL
W
Gas Valve
B
R
IGNITER
BK
*Blower speed control switch is provided in FBK200 blower kit.
Schematic Representation Only
**ON/OFF Switch (Integral
with Gas Valve) **Leave the ON/OFF switch, which is integral
with the gas valve, in the ON position.
OPTIONAL APPLIANCE-MOUNTED ON/OFF SWITCH
OR OPTIONAL WALL SWITCH
OR OPTIONAL THERMOSTAT
OR OPTIONAL REMOTE RECEIVER
G
OPT
BLOWER
PILOT
ASSEMBLY
Junction Box
White
Green
Red
Black
Neutral
Side of
Receptacle
Tab Intact
Green
Ground
Screw
Hot
Side of
Receptacle
Ta b
Broken
120 VAC - Black
n
e
e
r
G-dn
u
o
r
G
Optional
Accessory
Switch
e
ti
h
W
-
lar
t
u
e
N
1. If any of the original wire as supplied must be replaced,
1. it must be replaced with Type AWM 105°C –18 GA. wire.
2. 120V, 60Hz –Less than 3 amps.
BK
Transf.
120 V.
24 V
Factory Wired Field Wired
BL
Electronic Wiring Diagram (Honeywell)
Showing the Blower Wiring for the Optional
FBK-250 Kits
R
WH
BL
W
Gas Valve
B
R
IGNITER
BK
Schematic Representation Only
*ON/OFF Switch (Integral
with Gas Valve)
Optional
FBK-250
Module
*Leave the ON/OFF switch, which is integral
with the gas valve, in the ON position.
G
OPTIONAL APPLIANCE-MOUNTED ON/OFF SWITCH
OR OPTIONAL WALL SWITCH OR OPTIONAL THERMOSTAT
OR OPTIONAL REMOTE RECEIVER
PILOT
ASSEMBLY
OPT
BLOWER
Junction Box
White
Green
Red
Black
Neutral
Side of
Receptacle
Tab Intact
Green
Ground
Screw
Hot
Side of
Receptacle
Ta b
Broken
Optional
Accessory
Switch
120 VAC - Black
n
e
e
r
G-dn
u
o
r
Ge
ti
h
W
-
lar
t
u
e
N

10 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
NOTES:

11
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Rocker Switch Kit 80L41 FRS
Unit-Mountable Rocker Switch
Thisrockerswitchkitcanbeinstalleddirectlyin
the gas valve mounting bracket (millivolt gas
valve equipped fireplaces) to provide On/Off
operation in lieu of a wall switch.
ACCESSORY COMPONENTS
Remote Control System (Standard) H0249 RCL
Standard Remote Control System
The Model RCL (Standard) Remote Control
System,featuresasimpleOn/Offcontrolfunc-
tion for the fireplace. This model includes a
hand-held transmitter, a remote receiver with
wall-mount coverplate and all hardware re-
quired to install the unit. The remote receiver
can be wall or hearth mounted.
Deluxe Remote Control System
The Model RCL-T (Deluxe) Remote Control
System has all of the features of the standard
system along with an added easy to read LCD
screen which presents access to many en-
hancements, including; battery power level in-
dicator,timer,modeofoperation,thermostatic
display including room temperature in either
metric of English units, flame indicator and
clock. Fully programmable, the Model RCL-T
allowsforcommandovernearlyalloperational
andtemperaturevariables,usingthehandheld
remote control transmitter.
Remote Control System (Deluxe) H0251 RCL-T
Touch-Up Paint Kit
Repairofminor scratchesand discoloration of
the appliance's painted surfaces may be ac-
complished with the use of these touch-up
paint kits.
Touch-Up Paint (Charcoal) Kit 90L74 TPK-C
Touch-Up Paint (Tan) Kit 98K67 TPK-T
Forced Air Blower Kits
-Single Speed 80L84 FBK-100
-Variable Speed with wall-mountable switch
80L85 FBK-200
-Variable Speed with unit- or wall-mountable switch
80L86 FBK-250
Forced Air Kit
TheFBK-100blowerprovidesconstantvelocity
forced air circulation. The FBK-200 assembly
with variable speed, wall-mountable switch
provides variable speed forced air circulation.
The FBK-250 assembly with variable speed
wall- or unit-mountable switch, also provides
variable speed forced air circulation.

12 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
ACCESSORY COMPONENTS CONTINUED
These screen panels can be installed on the
glassenclosurepaneltopreventdirectcontact
with the hot glass surface. The screen panel
kits cannot be used in conjunction with either
of the arch door kits or door frame kits.
The kits attach to the glass enclosure panel
without the use of hardware. The decorative
archkitscannot beusedinconjunction with
the screen panel kit.
stiKrooDhcrA .oNgolataC .oNledoM
.oNledoM8233-DPM0353-DPM5304-DPM0454-DPM
dehsiloP ssarB hsiniF
50L89 BPC33KDA 34M62 BPMC53KDA 53L18 BPC04KDA 63L18 BPC54KDA
dehsurB sselniatS hsiniF
26L89 SBC33KDA 44M62 SBMC53KDA 96L89 SBC04KDA 07L89 SBC54KDA
stiKlenaPneercS
.oNledoM .oNgolataC .oNledoM
8233-DPM 40L89 33GH
0353-DPM 84M62 M53GH
5304-DPM 94M62 M04GH
0454-DPM 05M62 M54GH
These screen panel kits can be installed on the glass enclosure panel to prevent direct contact with
the hot glass surface. The panel kits add a new design choice with a handsome textured iron finish.
Thescreenpanelkitscannotbeusedinconjunctionwitheitherofthearchdoorkitsordoorframekits.
stiKlenaPneercShcrA
.oNledoM .oNgolataC .oNledoM
8233-DPM 2953H IT33KPSAD
0353-DPM 3953H IT53KPSAD
5304-DPM 4953H IT04KPSAD

13
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Clean faced panel kits are available to convert
thestandardlouveredfireplacestoradiantmod-
els which are more suited for finishing around
thefireboxopeningwithnon-combustible ma-
terials, such as tile.
Thesehoodkitsreplacethestandardhoodthat
comes with these fireplaces.
Theselouvers aredesigned toreplace eitherthe
middle charcoal louver of each louver set or the
charcoal louver in each set closest to the glass
enclosure panel.
ACCESSORY COMPONENTS CONTINUED
stiKrevuoLeceiP-2
ledoM .oN
.oNgolataC .oNledoMdehsiloP ssarB dehsurB sselniatS
-DPM 8233 90L89 BP33RVL2 80L89 SB33RVL2
-DPM 0353 50L69 BP53RVL2 90L69 SB53RVL2
-DPM 5304 60L69 BP04RVL2 01L69 SB04RVL2
-DPM 0454 70L69 BP54RVL2 11L69 SB54RVL2
stiKlenaPecaFnaelC
.oNledoM .oNgolataC .oNledoM
8233-DPM 74M62 CM33DAR
0353-DPM 63L88 2-C53DAR
5304-DPM 73L88 2-C04DAR
0454-DPM 83L88 2-C54DAR
stiKdooH
.oNledoM
.oNgolataC .oNledoM dehsiloP ssarB dehsurB sselniatS
8233-DPM 01L89 BP33BE 11L89 SB33BE
0353-DPM 76K69 BP53BE 94L88 SB53BE
5304-DPM 86K69 BP04BE 05L88 SB04BE
0454-DPM 96K69 BP54BE 15L88 SB54BE
These louvers are designed to replace the
standardradiantpanelsthatareprovidedwith
the fireplace, or they may be used to replace
the charcoal colored louvers also available
with this fireplace. They include a top 3-piece
assembly and a bottom 3-piece assembly.
Thesekitsaredesignedtoattachdirectlytothe
front face of the fireplace at the four edges of
the glass enclosure panel.
These kits are designed to attach directly to
the front face of the appliance at the glass
enclosure panel's top and bottom edges.
stiKrevuoLdelbmessA
ledoM .oN
.oNgolataC .oNledoM
dehsiloP ssarB dehsurB sselniatS
-DPM 8233 54M42 BPM33RVL 64M42 SBM33RVL
-DPM 0353 82L88 2-BP53RVL 23L88 SB53RVL
-DPM 5304 92L88 2-BP04RVL 33L88 SB04RVL
-DPM 0454 03L88 2-BP54RVL 43L88 SB54RVL
stiKemarFrooDeceiP-2
ledoM .oN
.oNgolataC .oNledoM
dehsiloP ssarB dehsurB sselniatS
-DPM 8233 81L89 BP33KFD2 91L89 SB33KFD2
-DPM 0353 88M62 BP53KFD2 19M62 SB53KFD2
-DPM 5304 98M62 BP04KFD2 29M62 SB04KFD2
-DPM 0454 09M62 BP54KFD2 39M62 SB54KFD2
stiKemarFrooDeceiP-4
ledoM .oN
.oNgolataC .oNledoM
dehsiloP ssarB dehsurB sselniatS
-DPM 8233 22L89 BP33KFD4 32L89 SB33KFD4
-DPM 0353 28M62 BP53KFD4 58M62 SB53KFD4
-DPM 5304 38M62 BP04KFD4 68M62 SB04KFD4
-DPM 0454 48M62 BP54KFD4 78M62 SB54KFD4

14 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
ACCESSORY COMPONENTS CONTINUED
Style View Doors -
Style View Doors come in 4 beautiful styles. They are easy to install and will not require hardware to attach them to the standard
glass door frame. The door includes heavy duty magnet door latches and functional twin-pane doors.
Arch Design
Arch Pane Design Square Pane Design
Square Design
ARCH DESIGN KITS
Cat. No. Model Description Model Series
H0858 AD35C 35” Arch Doors, Charcoal
MPD3530
H0859 AD35TI 35” Arch Doors, Textured Iron
H0860 AD35SP 35” Arch Doors, Satin Pewter
H0861 AD35AB 35” Arch Doors, Antique Brass
H0862 AD40C 40” Arch Doors, Charcoal
MPD4035
H0863 AD40TI 40” Arch Doors, Textured Iron
H0864 AD40SP 40” Arch Doors, Satin Pewter
H0865 AD40AB 40” Arch Doors, Antique Brass
H0866 AD45C 45” Arch Doors, Charcoal
MPD4540
H0867 AD45TI 45” Arch Doors, Textured Iron
H0868 AD45SP 45” Arch Doors, Satin Pewter
H0869 AD45AB 45” Arch Doors, Antique Brass
ARCH PANE DESIGN KITS
H0930 APD35C 35” Arch Pane Doors, Charcoal
MPD3530
H0931 APD35TI 35” Arch Pane Doors, Textured Iron
H0932 APD35SP 35” Arch Pane Doors, Satin Pewter
H0933 APD35AB 35” Arch Pane Doors, Antique Brass
H0934 APD40C 40” Arch Pane Doors, Charcoal
MPD4035
H0935 APD40TI 40” Arch Pane Doors, Textured Iron
H0936 APD40SP 40” Arch Pane Doors, Satin Pewter
H0937 APD40AB 40” Arch Pane Doors, Antique Brass
H0938 APD45C 45” Arch Pane Doors, Charcoal
MPD4540
H0939 APD45TI 45” Arch Pane Doors, Textured Iron
H0940 APD45SP 45” Arch Pane Doors, Satin Pewter
H0941 APD45AB 45” Arch Pane Doors, Antique Brass
H0950 SD40C 40” Sq. Doors, Charcoal
MPD-4035
H0951 SD40TI 40” Sq. Doors, Textured Iron
H0952 SD40SP 40” Sq. Doors, Satin Pewter
H0953 SD40AB 40” Sq. Doors, Antique Brass
H0954 SD45C 45” Sq. Doors, Charcoal
MPD4540
H0955 SD45TI 45” Sq. Doors, Textured Iron
H0956 SD45SP 45” Sq. Doors, Satin Pewter
H0957 SD45AB 45” Sq. Doors, Antique Brass
SQUARE PANE DESIGN KITS
H0962 SPD35C 35” Sq. Pane Doors, Charcoal
MPD3530
H0963 SPD35TI 35” Sq. Pane Doors, Textured Iron
H0964 SPD35SP 35” Sq. Pane Doors, Satin Pewter
H0965 SPD35AB 35” Sq. Pane Doors, Antique Brass
H0966 SPD40C 40” Sq. Pane Doors, Charcoal
MPD-4035
H0967 SPD40TI 40” Sq. Pane Doors, Textured Iron
H0968 SPD40SP 40” Sq. Pane Doors, Satin Pewter
H0969 SPD40AB 40” Sq. Pane Doors, Antique Brass
H0970 SPD45C 45” Sq. Pane Doors, Charcoal
MPD4540
H0971 SPD45TI 45” Sq. Pane Doors, Textured Iron
H0972 SPD45SP 45” Sq. Pane Doors, Satin Pewter
H0973 SPD45AB 45” Sq. Pane Doors, Antique Brass
SQUARE DESIGN KITS
H0946 SD35C 35” Sq. Doors, Charcoal
MPD3530
H0947 SD35TI 35” Sq. Doors, Textured Iron
H0948 SD35SP 35” Sq. Doors, Satin Pewter
H0949 SD35AB 35” Sq. Doors, Antique Brass

15
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
ACCESSORY COMPONENTS CONTINUED
Tall Arch Pane Door
Style View Doors Continued -
Style View Doors also come in a Tall Arch Pane Design. Two distinctive grille kits, the “Crescents” and “Sunrise” design, are
also offered seperately. They are easy to install and will not require hardware to attach them to the standard glass door
frame. The door includes heavy duty magnet door latches and functional twin-pane doors.
“Crescents”Grille Kits “Sunrise”Grille Kits
TALL ARCH PANE DOORS
Cat. No. Model Description Model Series
H3525 TAPD35C 35”Arch Pane Doors, Charcoal MPD3530
H3527 35”Arch Pane Doors, Satin Pewter
40”Arch Pane Doors, Charcoal
40”Arch Pane Doors, Satin Pewter
45”Arch Pane Doors, Charcoal
45”Arch Pane Doors, Satin Pewter
TAPD35SP
H3529 TAPD40C
H3531 TAPD40SP
H3533 TAPD45C
H3535 TAPD45SP
MPD4035
MPD4540
“Sunrise”Grille Kits
Cat. No. Model Description Model Series
H3565 SUGK35C 35”Sunrise Upper Grille Kit, Charcoal
H3567 35”Sunrise Upper Grille Kit, Satin Pewter
SUGK35SP
H3569 SLGK35C 35”Sunrise Lower Grille Kit, Charcoal
H3571 35”Sunrise Lower Grille Kit, Satin Pewter
SLGK35SP
H3573 SUGK40C 40”Sunrise Upper Grille Kit, Charcoal
H3575 40”Sunrise Upper Grille Kit, Satin Pewter
SUGK40SP
H3577 SLGK40C 40”Sunrise Lower Grille Kit, Charcoal
H3579 40”Sunrise Lower Grille Kit, Satin Pewter
SLGK40SP
H3581 SUGK45C 45”Sunrise Upper Grille Kit, Charcoal
H3583 45”Sunrise Upper Grille Kit, Satin Pewter
SUGK45SP
H3585 SLGK45C 45”Sunrise Lower Grille Kit, Charcoal
H3587 45”Sunrise Lower Grille Kit, Satin Pewter
SLGK45SP
MPD3530
MPD4035
MPD4540
“Crescents”Grille Kits
Cat. No. Model Description Model Series
H3541 CUGK35C 35”Crescents Upper Grille Kit, Charcoal
H3543 35”Crescents Upper Grille Kit, Satin Pewter
CUGK35SP
H3545 CLGK35C 35”Crescents Lower Grille Kit, Charcoal
H3547 35”Crescents Lower Grille Kit, Satin Pewter
CLGK35SP
H3549 CUGK40C 40”Crescents Upper Grille Kit, Charcoal
H3551 40”Crescents Upper Grille Kit, Satin Pewter
CUGK40SP
H3553 CLGK40C 40”Crescents Lower Grille Kit, Charcoal
H3555 40”Crescents Lower Grille Kit, Satin Pewter
CLGK40SP
H3557 CUGK45C 45”Crescents Upper Grille Kit, Charcoal
H3559 45”Crescents Upper Grille Kit, Satin Pewter
CUGK45SP
H3561 CLGK45C 45”Crescents Lower Grille Kit, Charcoal
H3563 45”Crescents Lower Grille Kit, Satin Pewter
CLGK45SP
MPD3530
MPD4035
MPD4540

16 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
LIGHTING INSTRUCTIONS –HONEYWELL AND SIT MILLIVOLT GAS VALVE
FOR YOUR SAFETY READ BEFORE LIGHTING
A. This appliance has a pilot which must be lighted with a piezo
ignitor. When lighting the pilot, follow these instructions
exactly.
B. BEFORE OPERATING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas is
heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
•Extinguish any open flame.
•Open windows.
•Do not light any appliance.
•Do not touch any electrical switches.
TO TURN OFF GAS TO APPLIANCE
1. Turn remote wall switch “OFF.” The pilot will remain lit for
normal service.
2. For complete shutdown, turn remote wall switch to “OFF.”
3. Access the lower control compartment.
4. Depress gas control knob slightly and turn clockwise
to “OFF.” Do not force.
5. Close lower control compartment.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above on this page.
2. Access the lower control compartment.
3. Turn remote wall switch to “OFF.”
4. Verify main line shut-off valve is open.
5. Push in gas control knob slightly and turn clockwise
to “OFF.”
6. Wait five (5) minutes to clear out any gas. If you then smell gas,
STOP! Follow “B” in the safety information above on this page. If you
do not smell gas, go to the next step.
7. Push in gas control knob slightly and turn counterclockwise
to “PILOT.”
8. Push in control knob all the way and hold in.
Immediately light the pilot by triggering the
spark ignitor (pushing the button) until pilot
lights. Continue to hold the control knob in
for about 1 ¹⁄₂ minutes after the pilot is lit.
Release knob and it will pop back up. Pilot
should remain lit. If it goes out, repeat steps
5 through 8.
•If knob does not pop up when released,
stop and immediately call your service
technician or gas supplier.
•If pilot will not stay lit after several tries,
turn the control knob to “OFF” and call
your service technician or gas supplier.
9. Turn gas control knob counterclockwise
to “ON.”
10. Close lower control compartment.
•Do not use any phone in your building.
•Immediately call your gas supplier from a neighbor’s phone.
•If your gas supplier cannot be reached, call the fire depart-
ment.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
do not try to repair it, call a qualified service technician. Force
or attempted repair may result in a fire or an explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
Note: Knob cannot be turned from “PILOT” to “OFF”
unless the knob is pushed in slightly. Do not force.
HONEYWELL
MILLIVOLT
GAS VALVE
SIT
MILLIVOLT
GAS VALVE
O
N
O
F
F
P
I
L
O
T
L
O
H
I
PIEZO IGNITOR
H
I
L
O
W
TPTH TP TH
P
I
L
O
T
P
I
L
O
T
O
N
it
O
F
F
OUT
IN
PIEZO IGNITOR
HONEYWELL
MILLIVOLT PILOT
SIT
MILLIVOLT PILOT
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY
RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

17
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
INSTRUCTIONS D’ALLUMAGE –VANNE GAZ MILLIVOLT HONEYWELL ET SIT
INSTRUCTIONS D'ALLUMAGE
8. Enfoncez le bouton de réglage jusqu’au fond et gardez-le enfoncé.
Allumez immédiatement la veilleuse en déclenchant l’allume-gaz à
étincelle (en poussant le bouton) jusqu’à ce que la veilleuse
s’enflamme. Continuez de tenir le bouton de réglage enfoncé
pendant environ 90 secondes après l’allumage de la veilleuse.
Relâchez le bouton et il sortira
subitement. La veilleuse devrait rester
allumée. Si elle s’éteint, répétez les
étapes 5 à 8 inclusivement.
•Si le bouton ne sort pas
automatiquement après avoir été
relâché, arrêtez immédiatement et
téléphonez à votre technicien de
service ou à votre fournisseur de gaz.
•Si la veilleuse refuse de rester allumée
après plusieurs tentatives, tournez le
bouton de réglage jusqu’à sa position
d’arrêt “OFF” et téléphonez à votre
technicien de service ou à votre
fournisseur de gaz.
9. Tournez le bouton de réglage du gaz en
sens inverse des aiguilles d’une
montre jusqu’à sa position
de marche “ON”.
10. Fermez le compartiment de contrôle du bas.
11. Au besoin, rebrancher l’appareil au courant électrique et remettre
l’interrupteur du brûleur principal à la position “ON” ou régler le
thermostat à la température désirée.
12. Si l’appareil ne fonctionne pas, suivre les instructions intitulées
“Pour fermer le gaz qui alimente l’appareil” et appeler un
technicien ou le fournisseur de gaz.
POUR VOTRE SÉCURITÉ, LISEZ CES INSTRUCTIONS AVANT L’ALLUMAGE
A. Cet appareil est muni d’une veilleuse qui doit être allumée avec un
allumeur piézo-électrique. Lorsque vous allumez la veilleuse, suivre
exactement ces instructions.
B. AVANT L’ALLUMAGE: Assurez-vous que vous ne détectez aucune
odeurdegazautourdel’apareilainsiqueprèsdusol;certainsgaz,étant
plus lourds que l’air, descendent au niveau du sol.
VOICI CE QUE VOUS DEVEZ FAIRE SI VOUS DÉCELEZ UNE ODEUR
DE GAZ:
•Éteignez toute flamme visible.
•Ouvrez les fenêtres.
•N’allumez aucun appareil.
•Ne touchez à aucun commutateur électrique.
•Ne vous servez d’aucun téléphone dans votre édifice.
•Appelezimmédiatementvotrecompagniedegazenutilisantletéléphone
du voisin.
•S’ilvousestimpossibledecontactervotrecompagniedegaz,appelez
le service des incendies.
C. N’utilisez que votre main pour manipuler le bouton de réglage du gaz.
N’utilisez jamais d’outils. Si le bouton refuse de tourner ou de bouger,
n’essayez pas de le réparer. Communiquez immédiatement avec un
technicien de service qualifié. Toute tentative pour le forcer ou le
réparer, risquerait de provoquer un incendie ou une explosion.
D. Ne vous servez pas de cet appareil si l’un de ses éléments a été
immergé dans l’eau. Appelez immédiatement un technicien compétent
pour faire inspecter l’appareil et remplacer toute pièce du système de
réglage ou commande du gaz qui a été sous l’eau.
1. ARRÊTEZ! Lisez les consignes de sécurité au verso de cette plaque.
2. Ouvrez le compartiment de contrôle du bas.
3. Tournez l’interrupteur mural à la position d’arrêt “OFF”.
4. Assurez-vous que la soupape d’arrêt de la canalisation principale est
ouverte.
5. Enfoncez légèrement le bouton de réglage du gaz et tournez-le dans
le sens des aiguilles d’une montre jusqu’à la position
d’arrêt “OFF”.
Remarque: Il est impossible de tourner le bouton de “PILOT” à “OFF” à
moins qu’il ne soit légèrement enfoncé. Ne le forcez pas.
6. Attendez cinq (5) minutes pour l’evacuation du gaz. Si vous décelez
une odeur de gaz, ARRÊTEZ ! Retournez au point “B” des consignes
de sécurité au verso de cette plaque. Si vous ne remarquez aucune
odeur de gaz, passez à l’étape suivante.
7. Enfoncez légèrement le bouton de réglage du gaz et tournez-le en
sens inverse des aiguilles d’une montre jusqu’à la position de
veilleuse “PILOT”.
1. Tournez l’interrupteur mural à la position d’arrêt “OFF”. La veilleuse
restera allumée jusqu’au retour du service normal.
2. Pour une fermeture complète, tournez l’interrupteur mural à la
position d’arrêt “OFF”.
3. Ouvrez le compartiment de contrôle du bas.
POUR FERMER LE GAZ QUI ALIMENTE L’APPAREIL
4. Enfoncez légèrement le bouton de réglage du gaz et tournez-le dans
le sens des aiguilles d’une montre jusqu’à la position
d’arrêt “OFF”. Ne forcez pas le bouton.
5. Fermez le compartiment de contrôle du bas.
VANNE GAZ
MILLIVOLT
HONEYWELL
VANNE GAZ
MILLIVOLT SIT
HONEYWELL
MILLIVOLT PILOT
SIT
MILLIVOLT PILOT
O
N
O
F
F
P
I
L
O
T
L
O
H
I
PIEZO-ELECTRIQUE
H
I
L
O
W
TPTH TP TH
P
I
L
O
T
P
I
L
O
T
O
N
it
O
F
F
OUT
IN
PIEZO-ELECTRIQUE
AVERTISSEMENT : SI VOUS NE SUIVEZ PAS CES INSTRUCTIONS ÀLA LETTRE, IL POURRAIT S’EN SUIVRE UN INCENDIE OU UNE
EXPLOSION CAUSANT DES DOMMAGES MATÉRIELS, DES BLESSURES CORPORELLES OU MÊME DES PERTES DE VIE.

18 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
A. When lighting the appliance, follow these instructions
exactly.
B. BEFORE OPERATING smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
•Extinguish any open flame.
•Open windows.
•Do not light any appliance.
•Do not touch any electrical switches.
•Do not use any phone in your building.
FOR YOUR SAFETY READ BEFORE LIGHTING
•Immediately call your gas supplier from a neighbor’s
phone.
•If your gas supplier cannot be reached, call the fire
department.
C. Use only your hand to turn the gas control lever. Never
use tools. If the lever will not turn by hand, do not try to
repair it, call a qualified service technician. Force or
attempted repair may result in a fire or an explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
LIGHTING INSTRUCTIONS —ELECTRONIC
1. For complete shut-down, turn remote wall switch to
“OFF.”
2. Open lower control compartment door.
3. Turn the ON/OFF switch to “OFF”. Do not force.
4. Close the main line shut-off valve.
5. Close lower control compartment door.
TO TURN OFF GAS TO APPLIANCE
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above on this page.
2. Turn remote wall switch to “OFF.”
3. Open lower control compartment door.
4. Verify main line shut-off valve is open.
5. Turn the ON/OFF switch to “OFF”. Do not force.
6. Wait five (5) minutes to clear out any gas. If you then
smell gas, STOP! Follow “B” in the safety information
above on this page. If you do not smell gas, go to the
next step.
7. Turn the ON/OFF switch to “ON”. Do not force.
8. Turn “ON” all electrical power to appliance (remote wall
switch).
9. Close lower control compartment door.
TO SHUT OFF
1. Turn off all electrical power to the appliance (remote wall
switch).
ON/OFF Switch
OFF
IN
PSI
ON
CONTROL
IGNITER
Front View
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY
RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

19
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
INSTRUCTIONS D’ALLUMAGE —ELECTRONIC
INSTRUCTIONS D’ALLUMAGE
POUR VOTRE SÉCURITÉ, LISEZ CES INSTRUCTIONS AVANT L’ALLUMAGE
A. Lorsquevousallumezl’appareil,suivezexactementcesinstruc-
tions.
B. AVANT L’ALLUMAGE: Assurez-vous que vous ne détectez
aucune odeur de gaz autour de l’apareil ainsi que près du sol;
certainsgaz,étantpluslourdsquel’air,descendentauniveaudu
sol.
VOICI CE QUE VOUS DEVEZ FAIRE SI VOUS DÉCELEZ UNE
ODEUR DE GAZ
•Éteignez toute flamme visible.
•Ouvrez les fenêtres.
•N’allumez aucun appareil.
•Ne touchez à aucun commutateur électrique.
•Ne vous servez d’aucun téléphone dans votre édifice.
•Appelezimmédiatementvotrecompagniedegazenutilisant
le téléphone du voisin.
•S’il vous est impossible de contacter votre compagnie de
gaz, appelez le service des incendies.
C. N’utilisez que votre main pour manipuler linterrupteur “ON/
OFF” de la valve à gaz. N’utilisez jamais d’outils. Si
l’interrupteur ne bouge pas manuellement, n’essayez pas de le
réparer. Communiquez immèdiatement avec un technicien de
service qualifié. Toute tentative pour forcer l’interrupteur ou le
réparer, risquerait de provoquer un incendie ou une explosion.
D. Nevousservezpas decet appareilsi l’unde sesélémentsaété
immergé dans l’eau. Appelez immédiatement un technicien
compétent pour faire inspecter l’appareil et remplacer toute
piècedusystèmederéglageoucommandedugazquiaétésous
l’eau.
1. ARRÊTEZ ! Lisez les consignes de sécurité au verso de cette
plaque.
2. Tournez l’interrupteur mural à la position d’arrêt “OFF”.
3. Ouvrez la porte du compartiment de contrôle du bas.
4. Assurez-vousquelasoupaped’arrêtdelacanalisationprincipale
est ouverte.
5. Tournezlamanettederéglagedugazàlapositiond’arrêt“OFF”.
6. Attendez cinq (5) minutes pour l’evacuation du gaz. Si vous
décelezuneodeurdegaz ARRÊTEZ! Retournezaupoint“B”des
consignes de sécurité au verso de cette plaque. Si vous ne
remarquez aucune odeur de gaz, passez à l’étape suivante.
7. Tournezlamanettederéglagedugazjusqu’àlapositiondemarche
“ON”. Ne la forcez pas.
8. Ouvrez le courant électrique (“ON”) qui alimente l’appareil
(interrupteurmural).
9. Fermez la porte du compartiment de contrôle du bas.
10. Au besoin, rebrancher l’apareil au courant électrique et
remettre l’interrupteur principal du brûleur à la position “ON”
ou régler le thermostat à la température désirée.
11. Si l’appareil ne se met pas en marche, suivre les instructions
intitulées “Pour fermer le gaz qui alimente l’appareil” et appeler
un technicien ou le fournisseur de gaz.
POUR ÉTEINDRE L’APPAREIL
1. Coupeztoutlecourantélectriquequialimentel’appareil(interrupteur
mural).
POUR FERMER LE GAZ QUI ALIMENTE L’APPAREIL
3. Tournezlamanettederéglagedugazàlapositiond’arrêt“OFF”.
Ne la forcez pas.
4. Fermez la soupape d’arrêt de la canalisation principale.
5. Fermez la porte du compartiment de contrôle du bas.
1. Pourunefermeturecomplète,tournezl’interrupteur mural à la
position d’arrêt “OFF”.
2. Ouvrez la porte du compartiment de contrôle du bas.
Interrupteur
ON/OFF
OFF
IN
PSI
ON
CONTROL
IGNITER
Vue de face
AVERTISSEMENT: SI VOUS NE SUIVEZ PAS CES INSTRUCTIONS ÀLA LETTRE, IL POURRAIT S’EN SUIVRE UN INCENDIE OU
UNE EXPLOSION CAUSANT DES DOMMAGES MATÉRIELS, DES BLESSURES CORPORELLES OU MÊME DES PERTES DE VIE.

20 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
TROUBLESHOOTING THE MILLIVOLT GAS CONTROL SYSTEM
1. Spark ignitor will not light
pilot after repeated
triggering of ignitor button.
2. Pilot will not stay lit after
carefully following the
lighting instructions.
3. Pilot burning, no gas to
burner, Valve knob “ON,”
Wall Switch “ON.”
4. Frequent pilot/burner outage
problem.
CORRECTIVE ACTIONSYMPTOM
A. Defective ignitor
(no spark at electrode).
B. Defective or misaligned electrode
at pilot (spark at electrode).
C. Gas supply pressure errant.
D. Pilot orifice plugged.
A. Defective pilot generator
(thermocouple).
A. Wall switch or wires defective.
B. Thermopile may not be generating
sufficient millivoltage.
C. Plugged burner orifice.
A. Pilot flame may be too low or
blowing (high) causing the pilot/
valve safety to drop out.
Check for spark at electrode and pilot; if no spark and
electrode wire is properly connected, replace ignitor.
POSSIBLE CAUSES
Note: Before troubleshooting the gas control system, be sure external gas shut off valve (located at gas supply inlet) is in
the “ON” position.
Important: Valve system troubleshooting should only be accomplished by a qualified service technician.
Clean and/or adjust pilot flame for maximum flame im-
pingement on thermocouple
(Figure 10, page 8 - SIT and
Figure 11, page 8 - Honeywell)
.
Check burner orifice for stoppage and remove.
Checkthermopilewithmillivoltmeter.Takereadingatthermo-
pile terminals of gas valve. Should read 325 millivolts mini-
mum with optional wall switch “OFF.” Replace faulty thermo-
pile if reading is below specified minimum.
Check wall switch and wires for proper connections. Jumper
wire across terminals at wall switch, if burner comes on,
replacedefectivewallswitch.Ifokay,jumperwiresacrosswall
switch wires at valve, if burner comes on, wires are faulty or
connections are bad.
Check pilot flame, it must impinge on thermocouple
(Figure 10, page 8 - SIT and Figure 11, page 8 - Honeywell) .
Clean and/or adjust pilot for maximum flame impinge-
ment on thermocouple. Ensure that the connection be-
tween the valve and thermocouple are tight and secure.
Clean or replace pilot orifice.
Check inlet gas pressure. It should be within the limits as
marked on the rating plate.
Using a match, light pilot. If pilot lights, turn off pilot and
triggertheignitorbuttonagain.Ifpilotlights,animpropergas
mixture caused the bad lighting and a longer purge period is
recommended. If pilot will not light – check gap at electrode
and pilot – should be ¹⁄₈" to have a strong spark. If gap
measures¹⁄₈",replacepilot
(Figure10,page8-SITand Figure
11, page 8 - Honeywell)
.