Lenovo ThinkServer RD120 Type 6444 User manual

ThinkServer RD120 Ty pes 6444, 6445, 6446, and 6447
Installation Guide

ThinkServer RD120 Ty pes 6444, 6445, 6446, and 6447
Installation Guide

Note: Before using this information and the product it supports, read the general information in Appendix B, “Notices,” on page 85
and the Warranty and Support Information document on the Lenovo ThinkServer Documentation DVD.
First Edition (October 2008)
©Copyright Lenovo 2008.
Portions ©Copyright International Business Machines Corporation 2007.
All rights reserved.
LENOVO products, data, computer software, and services have been developed exclusively at private expense and
are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights
to use, reproduction and disclosure.
LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered
pursuant aGeneral Services Administration ″GSA″contract, use, reproduction, or disclosure is subject to restrictions
set forth in Contract No. GS-35F-05925.

Contents
Safety ............................v
Chapter 1. Introduction ......................1
The Lenovo ThinkServer Documentation DVD ..............2
Hardware and software requirements ................2
Notices and statements in this document................3
Features and specifications.....................3
Major components of the server ...................5
Chapter 2. Installing optional devices ................7
Installation guidelines .......................7
System reliability guidelines....................8
Working inside the server with the power on .............8
Handling static-sensitive devices ..................9
Removing the cover .......................9
Installing amemory module ....................10
Memory mirroring .......................13
Online-spare memory .....................14
Installing ahard disk drive.....................16
Installing atape drive ......................17
Installing an additional microprocessor ................18
Installing an adapter .......................24
Installing aRemote Supervisor Adapter II SlimLine............27
Replacing the ServeRAID SAS controller ...............29
Completing the installation.....................30
Installing the cover ......................31
Connecting the cables .....................31
Updating the server configuration .................32
Chapter 3. Server controls, LEDs, and power.............35
Front view ..........................35
Rear view...........................37
Server power features ......................38
Turning on the server .....................39
Turning off the server .....................39
Chapter 4. Configuring the server .................41
Using the ThinkServer EasyStartup program ..............41
Using ThinkServer EasyManage products ..............43
Using the Configuration/Setup Utility program .............43
Configuring the Gigabit Ethernet controllers ..............43
Using the RAID configuration programs ................44
Using the IBM ServeRAID Configuration Utility program .........44
Using ServeRAID Manager ...................45
Using the baseboard management controller ..............47
Enabling and configuring SOL using the OSA SMBridge management utility
program .........................47
Installing the OSA SMBridge management utility program ........56
Using the baseboard management controller utility programs .......58
Chapter 5. Solving problems ...................61
Diagnostic tools overview .....................61
POST beep codes .......................61
©Lenovo 2008. Portions ©IBM Corp. 2007. iii

POST error codes........................63
EasyStartup problems ......................64
Troubleshooting tables ......................65
CD-RW/DVD drive problems ...................65
General problems .......................66
Hard disk drive problems ....................66
Intermittent problems......................67
USB keyboard, mouse, or pointing-device problems ..........68
Memory problems.......................69
Microprocessor problems ....................70
Monitor problems .......................71
Optional-device problems ....................73
Power problems .......................73
Serial port problems ......................75
Software problems ......................76
Universal Serial Bus (USB) port problems ..............77
Video problems........................77
Light path diagnostics ......................77
Diagnosing problems using light path diagnostics ...........78
Light path diagnostics LEDs ...................78
Appendix A. Getting help and technical assistance ..........81
Before you call .........................81
Using the documentation .....................81
Getting help and information from the World Wide Web ..........82
Calling for service........................82
Using other services .......................83
Purchasing additional services ...................83
Lenovo product service......................83
Appendix B. Notices ......................85
Trademarks ..........................86
Important notes.........................86
Waste electrical and electronic equipment (WEEE) notices.........87
Battery return program ......................88
German Ordinance for Work gloss statement..............89
Electronic emissions notices ....................89
Federal Communications Commission (FCC) statement .........89
Industry Canada Class Aemission compliance statement ........90
Avis de conformité àla réglementation d'Industrie Canada ........90
Australia and New Zealand Class Astatement ............90
United Kingdom telecommunications safety requirement.........90
European Union EMC Directive conformance statement.........90
German Class Acompliance statement ...............90
Japanese Voluntary Control Council for Interference (VCCI) statement ...91
Taiwanese Class Awarning statement ...............92
Chinese Class Awarning statement ................92
Korean Class Awarning statement ................92
Index ............................93
iv ThinkServer RD120 Types 6444, 6445, 6446, and 6447: Installation Guide

Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat udit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d’installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
Antes de instalar este producto, lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
©Lenovo 2008. Portions ©IBM Corp. 2007. v

Important:
Each caution and danger statement in this document is labeled with anumber. This
number is used to cross reference an English-language caution or danger
statement with translated versions of the caution or danger statement in the Safety
Information document.
For example, if acaution statement is labeled “Statement 1”, translations for that
caution statement are in the Safety Information document under “Statement 1.”
Be sure to read all caution and danger statements in this document before you
perform the procedures. Read any additional safety information that comes with the
server or optional device before you install the device.
Attention: The information in this document regarding installing and removing
power supplies and connecting and disconnecting power refers to ac power
supplies only. If the server contains dc power supplies, see the documentation that
comes with the dc power supplies. In adc power environment, only trained service
personnel other than Lenovo service technicians are authorized to connect or
disconnect power to the dc power supply and to install and remove adc power
supply.
vi ThinkServer RD120 Types 6444, 6445, 6446, and 6447: Installation Guide

Statement 1:
DANGER
Electrical current from power, telephone, and communication cables is
hazardous.
To avoid ashock hazard:
vDo not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
vConnect all power cords to aproperly wired and grounded electrical
outlet.
vConnect to properly wired outlets any equipment that will be attached to
this product.
vWhen possible, use one hand only to connect or disconnect signal
cables.
vNever turn on any equipment when there is evidence of fire, water, or
structural damage.
vDisconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
vConnect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached
devices.
To Connect: To Disconnect:
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
1. Turn everything OFF.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
Safety vii

Statement 2:
CAUTION:
When replacing the lithium battery, use only the battery recommended by the
manufacturer. If your system has amodule containing alithium battery,
replace it only with the same module type made by the same manufacturer.
The battery contains lithium and can explode if not properly used, handled, or
disposed of.
Do not
vThrow or immerse into water
vHeat to more than 100°C (212°F)
vRepair or disassemble
Dispose of the battery as required by local ordinances or regulations.
viii ThinkServer RD120 Types 6444, 6445, 6446, and 6447: Installation Guide

Statement 3:
CAUTION:
When laser products (such as CD drives, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
vDo not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable
parts inside the device.
vUse of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following.
Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.
Class 1 Laser Product
Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
Appareil A Laser de Classe 1
`
Safety ix

Statement 4:
≥18 kg (39.7 lb) ≥32 kg (70.5 lb) ≥55 kg (121.2 lb)
CAUTION:
Use safe practices when lifting.
Statement 5:
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.
1
2
xThinkServer RD120 Types 6444, 6445, 6446, and 6447: Installation Guide

Statement 8:
CAUTION:
Never remove the cover on apower supply or any part that has the following
label attached.
Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no serviceable parts inside
these components. If you suspect aproblem with one of these parts, contact
aservice technician.
Statement 26:
CAUTION:
Do not place any object on top of rack-mounted devices.
Safety xi

This server is suitable for use on an IT power-distribution system whose maximum
phase-to-phase voltage is 240 Vunder any distribution fault condition.
Important: This product is not suitable for use with visual display workplace
devices according to Clause 2of the German Ordinance for Work with Visual
Display Units.
xii ThinkServer RD120 Types 6444, 6445, 6446, and 6447: Installation Guide

Chapter 1. Introduction
This Installation Guide contains instructions for setting up your Lenovo®
ThinkServer™RD120 Types 6444, 6445, 6446, and 6447 server and basic
instructions for installing some optional devices. More detailed instructions for
installing optional devices are in the User Guide on the ThinkServer Documentation
DVD, which comes with the server. This document contains information about:
vSetting up and cabling the server
vStarting and configuring the server
vInstalling some optional devices
vSolving problems
Attention: The information in this document regarding installing and removing
power supplies and connecting and disconnecting power refers to ac power
supplies only. If the server contains dc power supplies, see the documentation that
comes with the dc power supplies. In adc power environment, only trained service
personnel other than Lenovo service technicians are authorized to connect or
disconnect power to the dc power supply and to install and remove adc power
supply.
The server has two model styles, which are based on the size and number of hard
disk drive bays:
vThe 3.5-inch models have six 3.5-inch hot-swap hard disk drive bays. Install only
3.5-inch drives in these models. If you intend to install atape drive, the tape
drive will occupy two of the six 3.5-inch drive bays.
vThe 2.5-inch models have eight 2.5-inch hot-swap hard disk drive bays and one
3.5-inch tape drive bay. Install only 2.5-inch hard disk drives and an optional
3.5-inch tape drive in these models.
Throughout this documentation, the terms 2.5-inch models and 3.5-inch models are
used to distinguish between the server styles.
If firmware and documentation updates are available, you can download them from
the Lenovo Web site. The server might have features that are not described in the
documentation that comes with the server, and the documentation might be updated
occasionally to include information about those features, or technical updates might
be available to provide additional information that is not included in the server
documentation. To check for updates, complete the following steps:
Note: Changes are made periodically to the Lenovo Web site. The actual
procedure might vary slightly from what is described in this document.
1. Go to: http://www.lenovo.com/support.
©Lenovo 2008. Portions ©IBM Corp. 2007. 1

2. Enter your product number (machine type and model number) or select Servers
from the Select your product list.
3. Select Servers from the Brand list.
4. From Family list, select ThinkServer RD120,and click Continue.
The server comes with an ThinkServer EasyStartup DVD to help you configure the
hardware, install device drivers, and install the operating system.
The server comes with alimited warranty. You can obtain up-to-date information
about the server and other Lenovo products at http://www.lenovo.com/thinkserver.
Record information about the server in the following table. You will need this
information when you register the server with Lenovo.
Product name ThinkServer RD120
Machine type 6444, 6445, 6446, and 6447
Model number _____________________________________________
Serial number _____________________________________________
The model number and serial number are on the ID label 1 on the bezel, as
shown in the following illustration.
Note: This illustration shows amodel with 3.5-inch serial-attached SCSI (SAS)
hot-swap hard disk drives. Models with 2.5-inch SAS hot-swap hard disk drives are
also available. The location of the ID label is the same on both model styles. This
illustration might differ slightly from your hardware.
For alist of supported optional devices for the server, see http://www.lenovo.com/
accessories.
See the Rack Installation Instructions document for complete rack installation and
removal instructions.
The Lenovo ThinkServer Documentation DVD
The Lenovo ThinkServer Documentation DVD contains documentation for the
server in Portable Document Format (PDF).
Hardware and software requirements
The Lenovo ThinkServer Documentation DVD requires the following minimum
hardware and software:
2ThinkServer RD120 Types 6444, 6445, 6446, and 6447: Installation Guide

vMicrosoft®Windows®XP, Windows 2000, or Red Hat Linux
v100 MHz microprocessor
v32 MB of RAM
vAdobe®Acrobat®Reader 3.0 (or later) or xpdf, which comes with Linux operating
systems
Notices and statements in this document
The caution and danger statements that appear in this document are also in the
multilingual Safety Information document, which is on the Lenovo ThinkServer
Documentation DVD. Each statement is numbered for reference to the
corresponding statement in the Safety Information document.
The following notices and statements are used in this document:
vNote: These notices provide important tips, guidance, or advice.
vImportant: These notices provide information or advice that might help you avoid
inconvenient or problem situations.
vAttention: These notices indicate potential damage to programs, devices, or
data. An attention notice is placed just before the instruction or situation in which
damage could occur.
vCaution: These statements indicate situations that can be potentially hazardous
to you. Acaution statement is placed just before the description of apotentially
hazardous procedure step or situation.
vDanger: These statements indicate situations that can be potentially lethal or
extremely hazardous to you. Adanger statement is placed just before the
description of apotentially lethal or extremely hazardous procedure step or
situation.
Features and specifications
The following information is asummary of the features and specifications of the
server. Depending on the server model, some features might not be available, or
some specifications might not apply.
Racks are marked in vertical increments of 4.45 cm (1.75 inches). Each increment
is referred to as aunit, or “U.” A1-U-high device is 1.75 inches tall.
Notes:
1. Power consumption and heat output vary depending on the number and type of
optional features that are installed and the power-management optional features
that are in use.
2. The sound levels were measured in controlled acoustical environments
according to the procedures specified by the American National Standards
Institute (ANSI) S12.10 and ISO 7779 and are reported in accordance with ISO
9296. Actual sound-pressure levels in agiven location might exceed the
average values stated because of room reflections and other nearby noise
sources. The declared sound-power levels indicate an upper limit, below which
alarge number of computers will operate.
Chapter 1. Introduction 3

Table 1. Features and specifications
Microprocessor:
vIntel®Xeon™FC-LGA 771 dual-core
with 4MB Level-2 cache or
quad-core with 8MB (2x4 MB)
Level-2 cache
vSupport for up to two
microprocessors
vSupport for Intel Extended Memory
64 Technology (EM64T)
Note:
vUse the Configuration/Setup Utility
program to determine the type and
speed of the microprocessors.
Memory:
vTwelve DIMM connectors
vMinimum: 1GB
vMaximum: 48 GB
vType: Fully buffered DIMM (FBD)
PC2-5300 DIMMs only
vSizes: 512 MB, 1GB, 2GB, or
4GB (when available), in pairs
vChipkill™supported
Drives:
CD/DVD: IDE 24x CD-RW/ 8x DVD
combination
Expansion bays:
vHot-swap hard disk drive bays:
SAS only. Number and size depend
on the server model. One of the
following configurations:
–Six 3.5-inch drive bays (optional
tape drive [SATA or SCSI]
requires two of these bays)
–Eight 2.5-inch drive bays and
one tape-drive (SATA or SCSI)
bay
v
One 5.25-inch Ultrabay Enhanced
bay (CD-RW/DVD drive installed)
Expansion slots:
vTwo PCI Express x8 slots (x4
lanes) on system board (low profile)
vSupport for either of the following
optional riser cards:
–Riser card with two PCI Express
x8 slots (x8 lanes) (standard)
–Riser card with two 133
MHz/64-bit PCI-X slots
Hot-swap fans:
vStandard: Five
vMaximum: Ten -provide
redundant cooling
Hot-swap power supplies:
835 watts (100 -240 Vac)
vMinimum: One
vMaximum: Two -provide
redundant power
Size (2 U):
vHeight: 85.4 mm (3.36 in.)
vDepth: 705 mm (27.8 in.)
vWidth: 443.6 mm (17.5 in.)
vWeight: approximately 21.09 kg
(46.5 lb) to 29.03 kg (64 lb)
depending upon configuration
Integrated functions:
vBaseboard management controller
vTwo Broadcom 10/100/1000
Ethernet controllers with Wake on
LAN®support and TCP/IP Offload
Engine (TOE) support
vOne RAID controller, active only
when a8k or 8k-l SAS controller
is installed
vOne serial port
vOne serial-attached SCSI (SAS)
controller
vSeven Universal Serial Bus (USB)
ports (two on front and four on
rear of server, plus one internal),
v2.0 supporting v1.1
vTwo video ports (one on front and
one on rear of server)
vOne internal serial ATA (SATA)
connector for tape
vSupport for Remote Supervisor
Adapter II SlimLine
Note: In messages and
documentation, the term service
processor refers to the baseboard
management controller or the
optional Remote Supervisor Adapter
II SlimLine.
Video controller:
vATI RN50 video on system board
vCompatible with SVGA and VGA
v16 MB DDR video memory
ServeRAID SAS controller:
vServeRAID™-8k-l SAS Controller that
supports RAID levels 0, 1, 10
(standard)
vUpgradeable to ServeRAID-8k SAS
Controller, 256 MB with battery
backup, that supports RAID levels 0,
1, 1E, 5, 6, and 10
Environment:
vAir temperature:
–Server on: 10° to 35°C (50.0° to
95.0°F); altitude: 0to 914.4 m
(3000 ft). Decrease system
temperature by 0.75°C for every
1000-foot increase in altitude.
–Server off: 10° to 43°C (50.0° to
109.4°F); maximum altitude: 2133
m(7000 ft)
–Shipment: -40° to +60°C (-40° to
140°F); maximum altitude: 2133
m(7000 ft)
v
Humidity:
–Server on/off: 8% to 80%
–Shipment: 5% to 100%
Acoustical noise emissions:
vDeclared sound power, idle: 6.8 bel
vDeclared sound power, operating:
6.8 bel
Heat output:
Approximate heat output in British
thermal units (Btu) per hour:
vMinimum configuration: 1230 Btu per
hour (360 watts)
vMaximum configuration: 3390 Btu
per hour (835 watts)
Electrical input with hot-swap ac
power supplies:
vSine-wave input (50-60 Hz) required
vInput voltage range automatically
selected
vInput voltage low range:
–Minimum: 100 Vac
–Maximum: 127 Vac
v
Input voltage high range:
–Minimum: 200 Vac
–Maximum: 240 Vac
v
Input kilovolt-amperes (kVA)
approximately:
–Minimum: 0.29 kVA
–Maximum: 1.00 kVA
4ThinkServer RD120 Types 6444, 6445, 6446, and 6447: Installation Guide

Major components of the server
Blue on acomponent indicates touch points, where you can grip the component to
remove it from or install it in the server, open or close alatch, and so on.
Orange on acomponent or an orange label on or near acomponent indicates that
the component can be hot-swapped, which means that if the server and operating
system support hot-swap capability, you can remove or install the component while
the server is running. (Orange can also indicate touch points on hot-swap
components.) See the instructions for removing or installing aspecific hot-swap
component for any additional procedures that you might have to perform before you
remove or install the component.
The following illustrations show the major components in the server.
Note: The illustrations in this document might differ slightly from your hardware.
1 Cover 11 CD/DVD drive
2 Power-supply filler 12 Operator information panel
3 Power supply 13 Optional tape drive
Chapter 1. Introduction 5

4 Power backplane 14 Tape drive space filler
5 2.5-inch drive cage with hard disk
drive backplane
15 Tape drive filler
6 2.5-inch hard disk drive 16 CD/DVD media backplane
7 2.5-inch filler panel 17 Microprocessor air baffle
8 3.5-inch cage divider 18 3.5-inch hard disk drive backplane
9 3.5-inch hard disk drive 19 Fan bracket assembly
10 3.5-inch filler panel 20 Fans (5 or 10)
1 Riser-card assembly 8 VRM
2 Full-height adapter 9 Microprocessor
3 DIMM air baffle 10 Heat sink
4 DIMM 11 Heat sink filler
5 ServerRAID SAS controller 12 Remote Supervisor Adapter II
SilmLine
6 system board 13 Low-profile adapter
7 Heat sink retention module
6ThinkServer RD120 Types 6444, 6445, 6446, and 6447: Installation Guide