LesDiy 3128738 User manual

Lighting Kit LEGO 10274
Package contents：
2 x 30cm Red Dot Lights
2 x 30cm White Dot Lights
14 x 15cm White Dot Lights
3 x 15cm Red Dot Lights
2 x 15cm Yellow Dot Lights
2 x 15cm Green Strip Lights (with 7 lights)
2 x Warm White Strip Lights
3 x 6-port Expansion Boards
1 x 8-port Expansion Board
1 x 12-port Expansion Board
4 x 5cm Connecting Cables
1 x 10cm Connecting Cable
1 x 30cm Connecting Cable
2 x 50cm Connecting Cables
1 x Acousto-optic Control Switch Board
1 x Flicker Effects Board
1 x USB Cable
Extra pieces
Note:
Place wires on the surface or under the building blocks.
The wire can be place between the building blocks or under the block, but they should be placed

between the studs correctly.
Insert the connectors to the ports.
Be careful when you are operating, there’s only one correct way to insert, make sure the expansion
board is upward, find the soldered “=” sign on the left of the port. When you are inserting, the side
which the wires can be seen should be faced to the “=” sign and if you feel hard to insert, please stop,
and don’t force it, for that may result in bent pins inside the port or overheating of the expansion board.
At this point, use the tweezers to straighten the bent pins.
When installing dot lights, make sure they are correctly placed (Yellow LED package is exposed). You
can put they either on the top of the studs or between studs.

Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted
only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed
is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the
plug and the connector.
Finally, please pay attention to the positive and negative terminals of the battery when installing the
battery case.

Instructions for installing this kit：
Ghostbusters, ECTO-1 Acousto-optic Control Version, Lighting Kit, 16 bags in total.
Power supply： USB cable (self-contained power bank or mobile phone charger).
Firstly, take the power source (power bank or mobile phone charger), connect it to the USB
cable, connect the other end of the USB cable to the expansion board to verify all the lights
one by one.
After the verification, disconnect the lights and put them back to the bags.
（note: put the lights back to the bags when verification of the lights from the same bag
is done, then, continue to verify the lights in another bag.）
OK, Let’s Begin! （you can use the tweezer if necessary.）
（Tips: the tweezer is sharp, you should be careful when using it, do not hurt yourself or
scratch the pieces; be gentle and do not wear the cables.）

Instructions for installing this kit：
Take the car.
Turn to the head, open the engine.
Remove the lights from both sides.
Disconnect the trans pieces from the lights.

Take 4 white 15cm dot lights.
With lighting part facing up, reconnect the trans piece.
Install the other 3 lights in the same way.

Place the cables as per below, reconnect the lights.
Remove the following gray pieces from both sides.
Disconnect the black pieces from the blue pieces.

Take 2 red 15cm dot lights, 2 trans white 1x1 round plates.
Disconnect the gray round plates.
With lighting part facing up, connect the trans white round plate over as per below.

Install the other light in the same way.
Thread the cable through the gray piece and reconnect the black piece.
Reconnect the gray pieces.

Disconnect the following gray piece.
Remove the following 2 trans white round plates.
Take 2 yellow 15cm dot lights.

With lighting part facing up, thread the cable through the following hole and pull it out.
Install the other light in the same way.
Reconnect the 2 trans white round plates.

Remove the following 2 gray plates.
Stuck the cable between the gray pieces as per below.
Reconnect the gray plate.

Place the other cable similarly.
As per below.
Take a 30cm connecting cable, a 12-port expansion board, assemble them as per below.

Connect all the cables from the head to the expansion board.
Take 2 adhesive squares.
Stick them to the back of the expansion board, and stick the expansion board to the following
place.

Thread the cable from the expansion board through the following hole, and pull it out from
the bottom.
Reconnect the gray piece.
Tuck the cables with the tweezer.

Close the engine cover.
Turn to the side, and turn the car over.
Thread the cable through the following hole and pull it out.

Continue to thread it through the following hole.
Finally thread the cable through the following hole and pull it out.
Turn to the other side, and turn the car over.

Open the door.
Take a 10cm connecting cable, a 50cm connecting cable,2 warm white strip lights, assemble
them as per below.
Stick the strip lights to the following places.

Turn to the tail, open the door.
Turn to the side.
Thread the cable from the strip light through the following space to the tail, and pull it
out.