Leunig ePowerSwitch 8M+R2 User manual

ePowerSwitch 8M+R2
User guide
Version 03 2011

1
© Copyright by LEUNIG GmbH – Wilhelm-Ostwald-Straße 17 – D 53721 Siegburg - Germany
Printed in Germany
All rights reserved. No part of this documentation, accompanying software or other components of the
described product may be reproduced or transmitted in any form or by any means, electronic or mechanical,
including photocopying and recording, for any purpose other than the personal use of the purchaser without
the express written permission of LEUNIG GmbH
This documentation, the ePowerSwitch 8M+R2, its peripherals, accessories and accompanying software were
produced with great care, yet errors are possible.
LEUNIG GmbH assumes no responsibility for errors within the documentation, the hardware or the software.
LEUNIG GmbH reserves the right to change programs or the documentation from time to time without
informing the user, errors and omissions excepted.
Trademarks
All brand names and product names used in this book are trade names, service marks,
trademarks, or registered trademarks of their respective owners.

2
CONTENTS
SAFETY INSTRUCTIONS: To be read before use!...................................................................................... 3
1. DESCRIPTION.......................................................................................................................................... 4
1.1 Diagram............................................................................................................................................... 4
1.2 Package list......................................................................................................................................... 5
2. INSTALLATION......................................................................................................................................... 6
3. CONFIGURATION .................................................................................................................................... 7
3.1. Configuration through the LAN using the Finder program ................................................................. 7
3.2. Configuration through an RS232 Terminal connection...................................................................... 9
3.2.1. Serial port configuration ......................................................................................................... 10
3.2.2. Restore to default factory settings.......................................................................................... 10
3.2.3. Restore to default administrator password ............................................................................ 10
3.3. Configuration through the LAN using a standard Browser............................................................... 11
3.3.1. General / IP configuration ...................................................................................................... 12
3.3.2. General / System time............................................................................................................ 13
3.3.3. General / SNMP..................................................................................................................... 14
3.3.4. General / Tools....................................................................................................................... 15
3.3.5. Settings / Accounts................................................................................................................. 16
3.3.5.1 Settings / Accounts.................................................................................................... 16
3.3.5.2 Settings / Accounts / Hidden Page account............................................................... 18
3.3.6. Settings / Groups.................................................................................................................... 21
3.3.7. Settings / Peripherals............................................................................................................. 23
3.3.7.1. Settings / Peripherals - ePowerSwitch 8M+R2 .......................................................... 26
3.3.7.2. Settings / Peripherals - ePowerSwitch Satellite........................................................ 28
3.3.7.3. Settings / Peripherals - Analog inputs....................................................................... 31
3.3.7.3.1. Temperature, temp. and humidity, temp. and ambient light sensors....... 31
3.3.7.3.2. AC Current probe ..................................................................................... 34
3.3.7.3.3. EnergyMeter............................................................................................. 36
3.3.7.4. Settings / Peripherals - Digital Inputs........................................................................ 38
3.3.7.4.1. Digital Input Modules................................................................................ 38
3.3.7.4.2. Temperature and proximity sensors......................................................... 41
3.3.7.4.3. Push Button.............................................................................................. 43
3.3.8. Settings / Rules...................................................................................................................... 45
3.3.8.1. Settings / Rules - Schedule Rule.............................................................................. 47
3.3.8.2. Settings / Rules - Timer Rule.................................................................................... 50
3.3.8.3. Settings / Rules - Ping Monitoring Rule.................................................................... 52
3.3.8.4. Settings / Rules - Scan Monitoring Rule................................................................... 54
3.3.8.5. Settings / Rules - Power Supply Monitoring Rule..................................................... 56
3.3.8.6. Settings / Rules - Digital Input Monitoring Rule........................................................ 58
3.3.8.7. Settings / Rules - Analog Input Monitoring Rule....................................................... 60
3.3.9. Settings / Shutdowns.............................................................................................................. 63
3.3.10. Misc / Control Panel............................................................................................................. 65
3.3.11. Misc / Rule Panel ................................................................................................................. 66
3.3.12. Misc / Log............................................................................................................................. 67
3.3.13. Misc / Log Settings............................................................................................................... 68
4. POWER OUTLET CONTROL AND PERIPHERALS STATUS............................................................... 69
4.1. Command the Power Outlets through an Ethernet connection........................................................ 69
4.2. Command the Power Outlets through a serial connection............................................................... 70
4.3. Command the Power Outlets through the network using simple commands in your own program 71
5. APPENDIX............................................................................................................................................... 74
5.1. Sending status information and sensor values using rules.............................................................. 74
5.2. Ping and Scan Methods......................................................................................................... 75
5.3. Technical Data.................................................................................................................................. 76
5.4. Commonly used Ports...................................................................................................................... 76
5.5. Syslog Messages: Severity Level Definitions................................................................................... 77
Statement of Conformity.............................................................................................................................. 78

3
SAFETY INSTRUCTIONS: To be read before use!
NOTE
•The ePowerSwitch devices can only be installed by qualified people with the following installation and
use instructions. The manufacturer disclaims all responsibility in case of a bad utilization of the
ePowerSwitch devices and particularly any use with equipments that may cause personal injury or
material damage.
•This equipment is designed to be installed on a dedicated circuit that must have a circuit breaker or fuse
protection.
•The electrical power sockets used to plug the power cords of the ePowerSwitch devices must be close
to the ePowerSwitch devices and easily accessible.
•Check that the power cords, plugs and sockets are in good condition.
•The ePowerSwitch devices can only be connected to three-wire 230 VAC (50-60Hz) sockets.
•Always plug the ePowerSwitch devices into properly grounded power sockets (two poles plus ground).
•Never exceed 10 Amp total load for each group of 4 power outlets of an ePowerSwitch device.
•The ePowerSwitch devices are intended for indoor use only. Do NOT install them in an area where
excessive moisture or heat is present.
•Always disconnect the 2 (two) power cords of the ePowerSwitch device if you want to intervene on the
ePowerSwitch device or on the equipment powered from the ePowerSwitch device.
•The power outlets of the ePowerSwitch devices are not circuit breakers! If you want to intervene on
equipments connected to an ePowerSwitch device you must disconnect these equipments from the
ePowerSwitch device.
•Do NOT attempt to disassemble the ePowerSwitch devices, they contain potentially hazardous voltages.
•The ePowerSwitch devices contain no user serviceable parts and repairs are to be performed by factory
trained service personnel only.
•Always use a shielded cable for the Ethernet connection.

4
1. DESCRIPTION
ePowerSwitch*8M+R2 is a power distribution and control unit that enables remote power control over IP
or locally through an RS-232 Terminal connection.
Its serial interface can be used to control the power outlets over a Terminal connection (KVM Switch,
console server...) or to trigger a soft shutdown of a server with shutdown capabilities. An internal Real
Time Clock enables to trigger scheduled actions and timestamp all events (logs, SNMP traps and
Syslog events).
ePowerSwitch 8M+R2 is more than a simple power switch, it's also a modular Remote Monitoring
System which enables to increase the security of your facilities and reduces unforeseen downtimes of
your equipment. It offers environmental control functions and IP device monitoring with automatic reboot
function in case of lock-up.
It supports up to 4 peripherals (temperature/humidity/ambient light sensors, current probes, I/O
modules, Power Switches…).
Supported protocols: HTTP, DHCP, Syslog, SNMP and SNTP.
1.1 Diagram
The front panel of the ePowerSwitch 8M+R2
A 1 2 3 4 (LEDs)
A Green. Lights up when power applied on group A
1 Red. Status of power outlet 1 (On/Off)
2 Red. Status of power outlet 2 (On/Off)
3 Red. Status of power outlet 3 (On/Off)
4 Red. Status of power outlet 4 (On/Off)
10/100 (RJ45 Connector)
Network connection 10/100 Mbits/sec
Link (LED)
Off = Network connection not detected
On = Network connection detected
Flashing = the device is sending or receiving data over this port
5 LEDs (group A)
A = power supply A
1 - 4 = Status of outlets 1 - 4
RJ45 connecto
r
Ethernet Network
SUB-D9F connector
Terminal connection
A-xBus RJ45 connector
xBus Peripheral Connection
5 LEDs (group B)
B = power supply B
5 - 8 = Status of outlets 5 - 8

5
100 (LED)
Off = 10 Mbits/sec connection
On = 100 Mbits/sec connection
RS232 (SUB-D 9F Connector)
Serial port RS232 with DB-9 female connector
Pinout
2 = TxD
3 = RxD
5 = Gnd
A-xBus
The RJ45 connector is used for cascading up to 4 peripherals
Maximal TOTAL line length: 200 meters
B 5 6 7 8 (LEDs)
B Green. Lights up when power applied on group A
5 Red. Status of power outlet 5 (On/Off)
6 Red. Status of power outlet 6 (On/Off)
7 Red. Status of power outlet 7 (On/Off)
8 Red. Status of power outlet 8 (On/Off)
The back of the ePowerSwitch 8M+R2
1.2 Package list
The following items are included:
1 ePowerSwitch 8M+R2
2 power cable, 230 V / 10 Amp, length 1.80 Meters
1 RJ45 M/M cable, 2 Meters
1 serial cable SUB-D 9 points M/F, 1.80 Meters
1 quick installation guide
1 CD with User Guide, Quick Start Guide and Windows configuration program
Power input B
230 VAC – 10 Amp
Power outlets (Group B)
Power outlets 5 – 8
230 VAC max 10 Am
p
Power outlets (Group A)
Power outlets 1 – 4
230 VAC max 10 Am
p
Power input A
230 VAC – 10 Amp

6
2. INSTALLATION
Remark:
Make sure that the ePowerSwitch 8M+R2 is powered off.
Connection instructions
1. Use a shielded RJ45 network cable to connect your ePowerSwitch 8M+R2 to the network.
2. Use appropriated three-wire power cords (two poles plus ground) to connect your electrical devices to
the ePowerSwitch 8M+R2 unit.
3. Plug each power cable into a grounded socket. The power supply LEDs light on to confirm that power
is on.
4. You can now configure the ePowerSwitch 8M+R2 by following the indications of the chapter
"Configuration of the ePowerSwitch 8M+R2".

7
3. CONFIGURATION
To use the ePowerSwitch 8M+R2 on your network, you must first configure its network parameters. Ask
your network administrator for the parameters to use.
There are three methods to configure the network parameters of the ePowerSwitch 8M+R2:
3.1. Configuration through the LAN using the Finder program
It is the simplest and fastest configuration method if you use Windows as operating system. It allows to
configure your ePowerSwitch 8M+R2 through your local network even if its network parameters are not
compatible with those of your PC.
1. Start the Finder.exe program contained on the CD-ROM.
2. Open the File menu and choose SCAN (or click on the first left button in the tool bar) to discover the
ePowerSwitch 8M+R2 connected on your LAN.
3. Open the File menu and choose CONFIGURE (or click on the second left button in the tool bar) to
configure the network parameters.
This page enables to define all IP parameters of the ePowerSwitch 8M+R2 device and displays the
version of the Firmware. The HTTP protocol is enabled and the Finder program is authorized at factory
settings.
!!! To achieve the highest security level we suggest to disable the configuration using the
Finder program after the first installation.

8
DHCP:
Check this box is you want to obtain the IP address, the subnet mask and the default gateway for your
ePowerSwitch 8M+R2 via DHCP.
Use of DHCP (Dynamic Host Configuration Protocol) requires a DHCP host to be set up on the
network.
IP Address:
IP address of the ePowerSwitch 8M+R2, default is 192.168.100.200.
Subnet Mask:
Subnet Mask of the ePowerSwitch 8M+R2, default is 255.255.255.0.
Gateway:
Generally the address of your router, default is blank.
DNS 1:
Primary DNS (Domain Name Server), default is blank.
DNS 2:
Secondary DNS, default is blank.
Version:
Firmware version of the ePowerSwitch 8M+R2
Port Number:
Port number: default is 80 (HTTP).
Finder authorized:
The Network parameters of the ePowerSwitch 8M+R2 can be configured through a Local Area Network
using the provided Finder Program. It is a simple and fast configuration method if you use Windows as
operating system.
!!! The Finder Program is enabled as default value. For security reasons we suggest to disable the
Finder program after the first configuration.

9
3.2. Configuration through an RS232 Terminal connection
1. Use the provided RS232 cable to connect the ePowerSwitch to an available serial port of your PC.
2. Run a Terminal program such as Windows HyperTerminal or the Micro Terminal program on the CD.
3. Configure the appropriate serial port @ 9.600, n, 8, 1 and no flow control. If you use the MicroTerminal
program on the CD (folder miscellaneous) you only have to choose the used serial port, this program is
already configured at 9600,n,8,1.
4. On your computer, press <ENTER> until the menu appears on your screen.
5. Press the “M” on your keyboard and follow the menu to configure the network parameters of your
ePowerSwitch 8M+R2. ------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.100.200
LAN interface's subnet mask is 255.255.255.0
IP address of default gateway to other networks is 0.0.0.0
IP address of primary DNS server is 0.0.0.0
IP address of secondary DNS server is 0.0.0.0
MISCELLANEOUS:
HTTP Port is 80
Finder program is enabled
HARDWARE PARAMETERS:
MAC Address is nn.nn.nn.nn.nn.nn
------------------------------------------------------------ Configuration menu
Special commands (type /? or /Help)
/viewlog Displays the log file
/initlog Clears the log file
/initadminaccount Restores default administrator password
/restorefactconf Restores to factory default settings
/help /? Displays this help

10
3.2.1. Serial port configuration
Connector: SUB-D9 female connector
Pin configuration RS232 parameters
Pin 2 = TxD (transmit data to the PC) Speed: 9600 bauds
Pin 3 = RxD (receive commands) Parity: No
Pin 5 = GnD Format: 8 bits
Stopbit: 1
Flowcontrol: no
The serial cable provided with the ePowerSwitch-is a standard straight extension cable with DB9
connectors. This cable is intended to connect the serial port of the ePowerSwitch to a serial port of a PC.
3.2.2. Restore to default factory settings
If you want to restore the ePowerSwitch to factory settings, you can reset it to default value using following
procedure:
1. Use the supplied RS232 cable to connect the ePowerSwitch-to an available serial port of your PC.
2. Run a terminal program such as Windows HyperTerminal or the Micro Terminal program on the CD.
3. Configure the appropriate serial port with the following settings @ 9.600, n, 8, 1 and no flow control. If
you use the MicroTerminal program on the CD (folder miscellaneous) you only have to choose the
used serial port, this program is already configured at 9600,n,8,1.
4. On your computer, press <ENTER> until the menu appears on your screen.
5. Type in following command:
/restorefactconf (the command MUST be preceded with a slash).
Now you can log in using admin as Login name and password.
The login values are case sensitive.
3.2.3. Restore to default administrator password
If you have forgotten your administrator password, you can reset it to default value using following
procedure:
1. Use the supplied RS232 cable to connect the ePowerSwitch-to an available serial port of your PC.
2. Run a terminal program such as Windows HyperTerminal or the Micro Terminal program on the CD.
3. Configure the appropriate serial port with the following settings @ 9.600, n, 8, 1 and no flow control.If
you use the MicroTerminal program on the CD (folder miscellaneous) you only have to choose the
used serial port, this program is already configured at 9600,n,8,1.
4. On your computer, press <ENTER> until the menu appears on your screen.
5. Type in following command:
/initadminaccount (the command MUST be preceded with a slash).
The system answers:
System is restarting...
System Started
Now you can log in using admin as Login name and password.
The login values are case sensitive.

11
3.3. Configuration through the LAN using a standard Browser
During the first installation, change temporarily the network settings of your PC according to the default
network settings of the ePowerSwitch 8M+R2.
Factory network settings of the ePowerSwitch 8M+R2:
IP Address: 192.168.100.200 - Port: 80
Gateway: 255.255.255.0
1. Open your Web browser and type following IP address:
http://192.168.100.200/sysadmin.htm
2. Enter the administrator name and password (default for both = admin)
3. The home page appears, allowing you to configure all settings of your ePowerSwitch 8M+R2.

12
3.3.1. General / IP configuration
This page enables you to define all the IP parameters of the ePowerSwitch 8M+R2.
DHCP Client enabled:
Check this box if you want to obtain the IP address, the subnet mask and the default gateway for your
ePowerSwitch 8M+R2 via DHCP. Factory default setting for this option is disabled.
Use of DHCP (Dynamic Host Configuration Protocol) requires a DHCP host to be set up on the
network.
IP Address:
IP address of the ePowerSwitch 8M+R2, default is 192.168.100.200.
Subnet Mask:
Subnet Mask of the ePowerSwitch 8M+R2, default is 255.255.255.0.
Default Gateway:
Generally the address of your router, default is blank.
Primary DNS Address:
Primary DNS (Domain Name Server), default is blank
Secondary DNS Address:
Secondary DNS, default is blank
Finder Program enabled:
The Network parameters of the ePowerSwitch 8M+R2 can also be configured through a Local Area
Network using the provided Finder Program. It is a very simple and fast configuration method if you use
Windows as operating system.
The Finder Program is enabled as default value.
!!!For security reasons we suggest to disable the Finder program after the first configuration.
HTTP Port:
Port number: default is 80.
LOGOUT:
Click "Logout" at the bottom of the page to exit the session without saving changes.
DISCARD CHANGES:
Click "Discard Changes" at the bottom of the page to discard all the changes you have made on this page.
APPLY CHANGES:
Click "Apply Changes" at the bottom of the page to save changes.

13
3.3.2. General / System time
The system time of the ePowerSwitch 8M+R2 is used for synchronizing scheduling actions and to
timestamp SNMP traps, Syslog information and internal logs. The system time can be set manually with
the browser time of the connected computer or can be automatically synchronized with one or two NTP
timeservers.
Current System Time:
This field shows the current system time of the ePowerSwitch 8M+R2.
As the system time is displayed through the browser, a small difference (1 to 2 sec) can appear as
compared to the exact hour. The system time is nevertheless correct.
Use Browser Time:
If you want to set the system time using the current Browser time of your PC, select this option and click
on the "Set System Time" button.
Use NTP Server:
If you want to set the system time using an NTP timeserver, select this option, choose a refresh interval
and enter the IP address of the timeserver you wish to use in the "Primary" field. The address of a second
timeserver can be specified in the "Secondary" field. The secondary timeserver is optional and is used
only if the primary timeserver is not available.
You can enter either the hostname (in that case you must have specified a DNS server on the IP
configuration page) or the IP address of an NTP server.
NTP uses port 123/UDP.
Time Zone:
Set the time zone corresponding to your location. The system clock will subsequently show local time.
Without setting this, the system clock will show UTC/GMT time. Setting a time zone is only relevant if you
are synchronizing with an NTP server.
Daylight Saving Time:
If you want to set Daylight Saving dates, check this box and specify the date you want to use.
LOGOUT:
Click "Logout" at the bottom of the page to exit the session without saving changes.
DISCARD CHANGES:
Click "Discard Changes" at the bottom of the page to discard all the changes you have made on this page.
APPLY CHANGES:
Click "Apply Changes" at the bottom of the page to save changes.

14
3.3.3. General / SNMP
The ePowerSwitch 8M+R2 provides a built-in SNMP (Simple Network Management Protocol) agent, which
enables you to manage the ePowerSwitch 8M+R2 through SNMP-based network management systems.
The ePowerSwitch 8M+R2 MIB file enables to remotely read out the status of all power outlets and the
values of all sensors (temperature, humidity, ambient light). It also enables to control individually all power
outlets and all groups of power outlets. The MIB file is stored on the ePowerSwitch 8M+R2 and can be
downloaded from the General / Tools Page.
SNMP enabled:
Check this box if you want to enable the SNMP protocol.
Contact:
In this field, enter the name you want to give to the Contact field. The name can be from 1 to 64
characters long, and can contain alphanumeric characters. Default name is "contact".
Do not use quotes or special characters in labels!
Name:
In this field, enter the name you want to give to the Name field. The name can be from 1 to 64 characters
long, and can contain alphanumeric characters. Default name is "name".
Do not use quotes or special characters in labels!
Location:
In this field, enter the name you want to give to the Location field. The name can be from 1 to 64
characters long, and can contain alphanumeric characters. Default name is "location".
Read Community:
In this field, enter the name you want to give to the Read Community field. The name can be from 1 to 64
characters long, and can contain alphanumeric characters. Default name is "public".
Write Community:
Check this box if you want to be able to control the power outlets through a MIB browser. In the following
field, enter the name you want to give to the Write Community. The name can be from 1 to 64 characters
long, and can contain alphanumeric characters. Default name is "private".
Trap Community:
Check this box if you want to configure the ePowerSwitch 8M+R2 SNMP agent to send traps to a
community. In the following field, enter the name you want to give to the Trap Community. The name can
be from 1 to 64 characters long, and can contain alphanumeric characters. Default name is "trap".
Trap Destination 1:
Check this box and enter the primary SNMP Server address the traps will be sent to.
Trap Destination 2:
Check this box and enter the secondary SNMP Server address the traps will be sent to.
LOGOUT:
Click "Logout" at the bottom of the page to exit the session without saving changes.
DISCARD CHANGES:
Click "Discard Changes" at the bottom of the page to discard all the changes you have made on this page.
APPLY CHANGES:
Click "Apply Changes" at the bottom of the page to save changes.

15
3.3.4. General / Tools
This page enables you to:
- download and save the current settings of your ePowerSwitch 8M+R2 on your PC,
- upload an existing configuration file to your ePowerSwitch 8M+R2,
- restore the factory settings,
- download the ePowerSwitch 8M+R2 MIB file on your PC.
Save:
Click this button to save the current system settings onto your local hard drive.
Load:
Click this button and select a settings file you want to download to the ePowerSwitch 8M+R2.
Restore:
Click this button if you want to restore the factory default settings.
Save MIB:
Click this button if you want to download the ePowerSwitch 8M+R2 MIB file onto your local hard drive.
LOGOUT:
Click "Logout" at the bottom of the page to exit the session without saving changes.

16
3.3.5. Settings / Accounts
3.3.5.1 Settings / Accounts
This page is used to create, activate, deactivate, modify and delete up to 40 accounts.
- To activate or deactivate an account, check or uncheck the corresponding checkbox.
- To modify an account, click on "Edit" next to the corresponding account.
- To delete an existing account, click on "Delete" next to the corresponding account.
- To create an account, click on "Add a New Account" on the right side of the page.
A new page appears, allowing you to set all the parameters of the account.
User Name:
In this field, enter the name you want to give to the user. The name can be from 1 to 32 characters long,
and can contain alphanumeric characters.
Do not use quotes or special characters in labels!
Password:
In this field, enter the password you want to give to the user. The password can be from 4 to 32 characters
long, and can contain alphanumeric characters.
Confirm Password:
In this field, enter the password again.
IP Address Control:
Check this checkbox and specify an IP address or a range of IP address if you want to restrict the access
of this account.
Groups:
This field is used to add or remove groups to the current account.
To add Groups to the current account, press the Ctrl key and click on the displayed Groups. The selected
Groups are marked dark blue and their IDs are listed at the right side of the Groups field.
This field appears only if you have already created at least one group (Settings/Groups Tab).

17
Device:
In this drop-down list, choose a device from which you want to add Inputs or Outputs to the current
account.
Inputs/Outputs:
This field is used to add/remove Inputs or Outputs to/from the current account.
To add Inputs or Outputs to the current account, press the Ctrl key and click on the Inputs/Outputs of the
device selected in the previous field. The selected Inputs/Outputs are marked dark blue and their IDs are
listed at the right side of the Input/Output field.
The ePowerSwitch 8M+R2 supports number of peripherals which are clearly identified by specific ID
Codes.
LOGOUT:
Click "Logout" at the bottom of the page to exit the session without saving changes.
DISCARD CHANGES:
Click "Discard Changes" at the bottom of the page to discard all the changes you have made on this page.
APPLY CHANGES:
Click "Apply Changes" at the bottom of the page to save changes.

18
3.3.5.2 Settings / Accounts / Hidden Page account
This account is intended for developers who want to implement the power outlet control in own programs.
If activated, they can access to a special page named hidden.htm and control individually the power
outlets using simple commands.
- To activate or deactivate this account, check or uncheck the corresponding checkbox.
- To modify the Hidden page account, click on "Edit" next to the corresponding account.
A new page appears, allowing you to set all the parameters of the account.
Activated
This check box must be checked to activate the Hidden Page Account. It enables to deactivate temporarily
this account while keeping all its settings for a later use. The Hidden Page Account cannot be deleted.
User Name
In this field, enter the name you want to give to the Hidden Page Account.
The user name can be up to 32 characters long and contain alphanumeric characters.
Do not use quotes or special characters in labels!
Password
In this field, enter the password you want to give to the Hidden Page Account.
The password can be up to 32 characters long and contain alphanumeric characters.
Confirm Password
In this field, enter the password again for confirmation.
IP Address Control
Network security can be increased by IP address filtering. Check this checkbox and specify an IP address
or a range of IP addresses which has the right to access to the Hidden Page Account.

19
Groups
This field appears only if at least one group has already been created. To create a group, go to the
Settings/Groups Page.
- To add an existing group of Power Outlets to the current account, select the group you want to add in the
left field and click on the Arrow button, the group will then appear in the right field.
- To remove a Group from the current account, select the group you want to remove in the right field and
click on the Arrow button, the group will then appear in the left field.
Each group is clearly identified by its own ID (G1, G2, G3...) followed by the name given during the
configuration. If the symbol "!" appears between brackets behind the ID Code that means that the
Group is not activated. To activate it, go to the "Settings/Groups" page.
Device
In this drop-down list, choose the device from which one you want to add Inputs or Outputs to the current
account.
- Only properly connected devices or devices which already have been connected to the Power
Switch appears in this field.
- Each peripheral is clearly identified by its own ID followed by the name given during the
configuration. Behind the ID can appear a character between brackets which has following
meaning:
- "!" means that the corresponding device is properly connected to the Power switch but not
activated. To activate it, go to the "Settings/Peripherals" page.
- "X" means that the corresponding device has already been connected to the Power switch but
is currently no longer connected to the Power Switch.
Inputs/Outputs
- This field is used to add/remove Inputs or Outputs to/from the current account.
- To add an Input or Output to the current account, select the Input / Output you want to add in the left field
and click on the Arrow button, the selected Input / Output will then appear in the right field.
- To remove an Input or Output from the current account, select the Input / Output you want to remove in
the right field and click on the Arrow button, the selected Input / Output will then appear in the left field.
Accessing to the Hidden Page Account
To be able to access to the Hidden Page, you must have configured the Hidden Page Account and
activated it. For the first tests, simply check the Activated check box, start your browser and type into your
browser's address bar the IP address of your power switch followed by the name of the hidden page.
Example: if the IP address of your Power Switch is 192.168.100.200, type in:
http://192.168.100.200/hidden.htm followed by <ENTER>.
Your Web browser will now display:
Hidden Page
21 Dec 2010 01:50:03
ePowerSwitch 8M+ R2
Version: 2.1.0.0