Leuze electronic IT 1910i Parts list manual

IT 1910i
Industrial 2D-code hand-held scanner
TECHNICAL DESCRIPTION
EN 50123791 2013/06
We reserve the right to
make technical changes

© 2013
Leuze electronic GmbH + Co. KG
In der Braike 1
D-73277 Owen / Germany
Phone: [phone]
Fax: [phone]
http://www.leuze.com
[email protected]e

Contents
1Scope of delivery............................................................................................................................... 5
1.1 IT 1910i xx ........................................................................................................................................... 5
2Installation ......................................................................................................................................... 6
2.1 Connecting the hand-held scanner ..................................................................................................... 6
2.1.1 Switching off the PC ............................................................................................................................ 6
2.1.2 Connecting the IT 1910i ...................................................................................................................... 6
2.2 How do I scan codes? ......................................................................................................................... 7
2.2.1 Testing the scanner ............................................................................................................................. 7
3Technical Data................................................................................................................................... 8
3.1 Pin assignments of the connection cable ............................................................................................ 8
3.1.1 KB 232-1 IT 190x Part no. 50114517 ................................................................................................ 8
3.1.2 KB 232-1 IT 190x Part no. 50115105 ................................................................................................ 8
3.1.3 KB PS2-1 IT190x Part no. 50114519 ................................................................................................ 8
3.1.4 KB USB-1 IT 190x Part no. 50114521 .............................................................................................. 9
3.1.5 KB USB-2 IT 190x Part no. 50114523 .............................................................................................. 9
3.2 Reading fields ...................................................................................................................................... 9
4Resetting the IT 1910i to factory settings..................................................................................... 10
5Configuration................................................................................................................................... 11
5.1 IT 1910i to the serial PC interface ..................................................................................................... 12
5.1.1 With KB 232-1 IT190x Part no. 50114517 ...................................................................................... 12
5.1.2 With voltage supply via PIN 9 ........................................................................................................... 12
5.1.3 With voltage supply via power supply unit ........................................................................................ 13
5.1.4 Configuration for the Leuze standard protocol .................................................................................. 13
5.2 IT 1910i to MA 200i ........................................................................................................................... 14
5.2.1 Commissioning .................................................................................................................................. 14
5.3 IT 1910i to MA 21 .............................................................................................................................. 16
5.4 IT 1910i to PS2 interface ................................................................................................................... 17
5.5 IT 1910i to USB interface (keyboard emulation) ............................................................................... 18
5.6 IT 1910i to USB interface (COM port emulation) .............................................................................. 19
5.7 Activating the read process ............................................................................................................... 20
5.8 Configuration ..................................................................................................................................... 20
5.9 Troubleshooting ................................................................................................................................. 21
6Type overview.................................................................................................................................. 22
7Accessories/Spare parts ................................................................................................................ 23
Leuze electronic IT1910i 3

7.1 Connecting to Leuze multiNet Plus ................................................................................................... 24
7.2 Connection to various fieldbuses using MA 200i .............................................................................. 24
8Service and support........................................................................................................................ 25
Leuze electronic IT1910i 4

1 Scope of delivery
1.1 IT 1910i xx
1. Hand-held scanner IT 1910i xx
2. Package insert
An overview of the types can be found on page 22.
For accessories, see page 23.
Type designation Information about
standards
Scanner reading field
Leuze electronic IT1910i 5

2 Installation
2.1 Connecting the hand-held scanner
The individual steps for installing the cable on the scanner are shown in
the adjacent figure.
2.1.1 Switching off the PC
NOTICE
Make sure that the PC is switched off before connecting the
scanner.
2.1.2 Connecting the IT 1910i
1. To secure the connection cable to the scanner, proceed as follows:
Insert the RJ 41 connector into the socket on the bottom of the
hand-held scanner, close the cord grip and secure it using the
screw.
2. Connect the other end of the connection cable to the appropriate
connection socket on the PC.
3. You may need a power supply unit for supplying voltage; alternatively, you can use a cable which
supplies voltage from the computer system. Use the pin assignments (see page 8) to select the
appropriate cable for your application.
4. Connect the power supply unit to the power socket (not necessary if voltage is supplied from the
computer).
5. Check the operational readiness of the scanner by pointing the scanning surface towards a flat surface
and pulling the trigger. A red laser pattern as well as the red illumination should now be visible. Now scan
a sample label. The scanner emits an audible signal to confirm that the label has been read; if necessary,
the data are now passed on to the PC.
Cable latch
Leuze electronic IT1910i 6

2.2 How do I scan codes?
This section explains the best way to scan codes:
The scanner must be held at a slight angle to the
bar code. (Do not hold the scanner at a right angle
to the bar code.)
The red scanning pattern which serves as an
alignment aid should be positioned at the center of
the code. This ensures that the center point of the
camera is aligned with the code.
(The scanner will not be able to detect the label
correctly if it is not fully captured by the camera.)
The red scanning pattern is smaller when the
scanner is held closer to the code. Small codes
should be read at a smaller reading distance. With
larger codes, the reading distance must be large
enough so that the camera can capture the
complete code.
2.2.1 Testing the scanner
The adjacent bar code can be used for testing the scanner, the module
size is 0.5 mm (20 mil)
Code 39 bar code sample
Leuze electronic IT1910i 7

3 Technical Data
The technical data can be found in the data sheet for the IT 1910i.
3.1 Pin assignments of the connection cable
3.1.1 KB 232-1 IT 190x Part no. 50114517
Helix cable, maximum length 3 m. Signal level 0 and +5 volts TTL
Pin assignments of the 9-pin D-sub socket (female) for cable CBL-020-300-C00
Pin number
Signal
Designation
1
nc
Not used
2
TX
Transmit data
3
RX
Receiving line / Receive Data
4
nc
Not used
5
GND
Ground connection
6
DTR
Data set ready (+5 volt connected to output)
7
CTS
Clear to send
8
RTS
Request to send
9
VCC IN
4.5 – 5.5 V DC (if no power supply unit is
connected to the power supply unit connection)
Pin at power supply unit connection
Signal
Designation
Inside
VCC IN
4.5 - 5.5 V DC
Outside
GND
Ground connection
For the suitable power supply unit for IT 190x (100 - 230 V/50 – 60 Hz), see chapter 7.
3.1.2 KB 232-1 IT 190x Part no. 50115105
As with part number 50114517, but True RS 232 variant available with -12 to +12 volt signal level. Cable
designation: CBL-120-300-C00.
3.1.3 KB PS2-1 IT190x Part no. 50114519
Helix cable, maximum length 3 m.
Pin assignments of the Mini DIN socket or connector for cable CBL-720-300-C00
Pin connector
Pin socket
Signal
Designation
1
-
PC Data
PC data line
2
2
NC
Not used
3
3
GND
Ground connection
4
4
VCC IN
5 Volts DC
5
-
PC Clock
PC clock line
6
6
NC
Not used
-
1
KB data
Keyboard data line
-
2
KB clock
Keyboard clock line
Leuze electronic IT1910i 8

3.1.4 KB USB-1 IT 190x Part no. 50114521
Straight cable, maximum length 3 m.
Pin assignments of USB type A connector for cable CBL-500-300-S00
USB type A connector
Signal
Designation
1
VCC IN
5 Volts DC
2
Data -
Data line -
3
Data -
Data line +
4
GND
Ground connection
3.1.5 KB USB-2 IT 190x Part no. 50114523
Pin assignments of USB type A connector for cable CBL-500-500-C00:
as with part no. 50114521, but helix cable, maximum length 5 m.
3.2 Reading fields
IT 1910i ER-3
Code 39
5 mil
(0.127 mm)
UPC
13 mil
(0.330 mm)
Code 39
20 mil
(0.508 mm)
PDF
417
6.7 mil
(0.170 mm)
Data Matrix
10 mil
(0.254 mm)
QR Code
20 mil
(0.508 mm)
Typ. reading distance 1) [mm]
1) Dependent on code module
Leuze electronic IT1910i 9

4 Resetting the IT 1910i to factory settings
To reset all parameters to factory settings, scan the bar code shown below.
Attention!
All settings are lost!
Leuze electronic IT1910i 10

5 Configuration
Usually, bar codes are used to configure the hand-held scanner. Select the desired bar code and scan it
(see chapter 2.2). The configuration is then immediately accepted and executed.
A second option is to configure the hand-held scanner with the USB and RS 232 interfaces with the aid of the
VisualXpress PC program. You can download and install this program from our homepage at
www.leuze.com. The program can be used to make settings and transfer them to the hand-held scanner. The
configuration can also be stored so that it can be reused at a later time.
The standard applications are described and summarized below.
Leuze electronic IT1910i 11

5.1 IT 1910i to the serial PC interface
5.1.1 With KB 232-1 IT190x Part no. 50114517
For pin assignments, see chapter 3.1.1.
5.1.2 With voltage supply via PIN 9
Please connect the IT 1910i acc. to the adjacent figure.
Required parts:
1x 50122436 IT 1910i ER-3
1x 50114517 KB 232-1 IT190x
RS 232 transmission with 115200 baud, 8 data bits, 1 stop bit, no parity, no prefix and suffix.
Leuze electronic IT1910i 12

5.1.3 With voltage supply via power supply unit
Please connect the IT 1910i acc. to the figure below.
Required parts:
1x 50122436 IT 1910i ER-3
1x 50114517 KB 232-1 IT 190x
1x 50114525 Power supply unit
RS 232 transmission with 115200 baud, 8 data bits, 1 stop bit, no parity, no prefix and suffix.
5.1.4 Configuration for the Leuze standard protocol
Leuze standard protocol:
RS 232 with 9600 baud, 8 data bits, 1 stop bit, no parity, prefix STX and suffix CR/LF
Leuze standard protocol
Leuze electronic IT1910i 13

5.2 IT 1910i to MA 200i
RS 232 transmission with 9600 baud, 8 data bits, 1 stop bit, no parity, suffix CR/LF.
Required parts:
1x 50122436 IT 1910i ER-3
1x 50114517 KB 232-1 IT 190x
1x 50113397 KB JST-HS-300
1x 50112893 MA 204i Profibus gateway
or 50112892 MA 208i Ethernet gateway
or 50112891 MA 248i Profinet gateway
5.2.1 Commissioning
• Open the MA 200i
• Guide KB JST-HS-300 with the PG cable gland through the threaded hole and insert
the 12-pin JST connector
• Connect the IT 1910i with the RS 232 cable
• Connect the cable to the 9-pin D-sub connector
• Set the address using the address switch
• Insert the field bus connection cable
• Apply the voltage supply.
Leuze electronic IT1910i 14

IT1910i
KB JST-HS-300
approx. 0.3 m
9-pol. D-sub
18 to 30 V DC
Details on connecting the MA 200i can be found in "Technical description MA 200i".
5.2.1.1 Configuration
Data transmission to MA 200i
Leuze electronic IT1910i 15

5.3 IT 1910i to MA 21
RS 232 transmission with 9600 baud, 7 data bits, 1 stop bit, even parity, suffix CR/LF.
Required parts:
1x 50122436 IT 1910i ER-3
1x 50114517 KB 232-1 IT190x
1x 50035421 KB 021 Z
1x 50030481 MA 21 100
5.3.1.1 Pin assignments KB021 Z
Core color
Signal
Terminal assignments MA 21
brown
(RXD)
26
white
(TXD)
27
blue
(GND)
28
red
(VCC)
30
black
(GND)
31
bare (shield)
(PE)
21
5.3.1.2 Configuration
Connection to MA 21 with standard setting
Leuze electronic IT1910i 16

5.4 IT 1910i to PS2 interface
The operation of the IT 1910i in keyboard-wedge mode is described in this chapter. A PC keyboard is
emulated in this operating mode. The data which are read in are written directly to the currently activated
program. Thus, the data can be processed further in all standard programs.
Required parts:
1x 50122436 IT 1910i ER-3
1x 50114519 KB PS2-1 IT190x
Please connect the IT 1910i acc. to the adjacent figures.
To do this, proceed as follows:
1. Switch off the PC.
2. Unplug the keyboard.
3. Plug in the IT 1910i hand-held scanner
between the keyboard and the PC.
4. Switch the PC back on.
5. Scan the code shown below.
5.4.1.1 Configuration
PS2 keyboard emulation with CR LF
Disconnect
Leuze electronic IT1910i 17

5.5 IT 1910i to USB interface (keyboard emulation)
The operation of the IT 1910i in keyboard-wedge mode on a USB port is described in this chapter. A PC
keyboard is emulated in this operating mode. The data which are read in are written directly to the currently
activated program. Thus, the data can be processed further in all standard programs.
Required parts:
1x 50122436 IT 1910i ER-3
1x 50114521 KB USB-1 IT190x
or 50114523 KB USB-2 IT190x
Please connect the IT 1910i acc. to the adjacent figure.
To do this, proceed as follows:
1. Plug the IT 1910i hand-held scanner into a free USB port.
2. The scanner acknowledges this connection with an acoustic
signal.
3. Scan the code shown below.
4. The standard keyboard driver is then installed.
5.5.1.1 Configuration
USB keyboard emulation with CR LF
Leuze electronic IT1910i 18

5.6 IT 1910i to USB interface (COM port emulation)
The operation of the IT 1910i as a serial interface on a USB port is described in this chapter. A COM interface
is emulated in this operating mode. The data which are read in are sent to a new COM interface. The driver
with which you emulate this COM interface can be downloaded from our homepage at www.leuze.com. Thus,
the data can be processed further in programs which expect data via COM interfaces.
Required parts:
1x 50122436 IT 1910i ER-3
1x 50114521 KB USB-1 IT190x
or 50114523 KB USB-2 IT190x
Please connect the IT 1910i acc. to the figures shown below.
To do this, proceed as follows:
1. Install the USB serial driver for the 1910i. To do so, copy the driver
from the CD-ROM or from our homepage to the PC. Unpack the
file and start INSTALL.BAT. This requires administrator privileges
on the PC!
2. Plug the IT 1910i hand-held scanner into a free USB port.
3. The scanner acknowledges this connection with an acoustic
signal.
4. Scan the code shown below.
5. Open a terminal program or your program for the serial interface,
select the new COM port, and make the following settings: baud
rate 115200, 8 data bits, 1 stop bit and no parity. A CR is
transmitted as suffix (or terminator).
Leuze electronic IT1910i 19

5.6.1.1 Configuration
COM port emulation on the next free COM address with 38400 baud,
8 data bits, 1 stop bit, no parity and a CR as suffix.
5.7 Activating the read process
To activate the read process, a trigger signal is to be sent via the serial RS 232 interface or USB interface
(COM port emulation only). The command is to be sent at the set baud rate, parity, and data and stop bits.
The activation command is:
SYN T CR
ASCII decimal values: 022; 084; 013
To cancel read readiness, send a deactivation.
The deactivation command is:
SYN U CR
ASCII decimal values: 022; 085; 013
Following a successful read operation, the IT 1910i deactivates itself.
The second option is to use the trigger button to establish read readiness.
5.8 Configuration
Further details on configuration, such as parameters for code type release, number of digits, etc., can be
found in the User's Guide IT 1910i/1911i.
Leuze electronic IT1910i 20