Level Six Eleven Six User manual

OWNER’S GUIDE

2
READ THIS IMPORTANT INFORMATION BEFORE USING
YOUR STANDUP PADDLEBOARD
DISREGARDING ANY OF THE SAFETY PRECAUTIONS AND INSTRUCTIONS CONTAINED IN
THE OWNER’S MANUAL AND/OR ON THE PRODUCT MAY RESULT IN INJURY, INCLUDING
THE POSSIBILITY OF DEATH.
- REVIEW THE WEIGHT CAPACITY LIMITATIONS OF THIS BOARD AND NEVER EXCEED IT.
- ALWAYS WEAR A COAST GUARD APPROVED PERSONAL FLOTATION DEVICE (PFD).
- NEVER GO PADDLEBOARDING IN SEVERE WEATHER OR WATER CONDITIONS THAT
MIGHT AFFECT YOUR ABILITY TO STEER THE BOARD OR RETURN TO SHORE.
- NEVER ALLOW MINORS TO USE THIS BOARD WITHOUT ADULT SUPERVISION.
- NEVER CONSUME ALCOHOL OR ANY OTHER SUBSTANCES THAT MAY IMPAIR YOUR
COORDINATION, JUDGEMENT, OR ABILITY TO SAFELY PADDLE THE BOARD.
- NEVER USE THIS BOARD BEYOND YOUR SKILLS OR ABILITY.
- NEVER USE THIS PRODUCT AFTER SUNSET, BEFORE DAWN OR AT ANY TIME IN POOR
LIGHTING.
- CHECK LOCAL LAWS AND REGULATIONS REGARDING PROPER AND SAFE USE OF THIS
PRODUCT.
- NEVER USE THE VALVE WRENCH TO DEFLATE AN INFLATED BOARD.
- PRESSURE GAUGE WILL ONLY REGISTER PRESSURE ABOVE 10 PSI.
- DO NOT INFLATE SUP ABOVE 15 PSI.
- KEEP CLEAR OF SHARP OBJECTS AND/OR HEAT PRODUCING OBJECTS.

SECTION 1:
IDENTIFYING PARTS
& ACCESSORIES PAGES 4  6
SECTION 2:
CARE & MAINTENANCE PAGES 8  9
SECTION 3:
INFLATION
& DEFLATION PAGES 10  11
SECTION 4:
FIN INSTALLATION PAGE 12
SECTION 5:
REPAIRS PAGE 13
SECTION 6:
TRANSPORTATION TIPS PAGE14
SECTION 7:
LIMITED LIFETIME
WARRANTY PAGE 15
3
QUESTIONS | WARRANTY | PARTS & ACCESSORIES:
1-877-2LEVEL6
[email protected]OM
TABLE OF CONTENTS

4
A.
B.
C.
D.
E.
F.
TEN-SIX
INFLATABLE
SECTION 1 | IDENTIFYING PARTS & ACCESSORIES
G.
STANDUPPADDLEBOARD
BUNGEE RINGS & CORDS
DECK TRACTION PAD
CARRY HANDLE
AIR VALVE
LEASH DRING
FIN CLAMP
FIN
VALVE WRENCH
BOARD TOTE
HIGH PRESSURE PUMP
AIR HOSE
REPAIR KIT
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
K.
H.
M.
I.
J.
L.

5
A.
B.
C.
D.
E.
F.
ELEVEN-SIX
INFLATABLE
QUESTIONS | WARRANTY | PARTS & ACCESSORIES:
1-877-2LEVEL6
[email protected]OM
G.
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
K.
H.
M.
I.
J.
L.
STANDUP PADDLEBOARD
BUNGEE RINGS & CORDS
DECK TRACTION PAD
CARRY HANDLE
AIR VALVE
LEASH DRING
FIN CLAMP
FIN
VALVE WRENCH
BOARD TOTE
HIGH PRESSURE PUMP
AIR HOSE
REPAIR KIT

6
SECTION 1 | IDENTIFYING PARTS & ACCESSORIES
A.
B.
C.
D.
E.
F.
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
TWELVE-SIX
INFLATABLE
K.
H.
M.
I.
J.
L.
G.
STANDUP PADDLEBOARD
BUNGEE RINGS & CORDS
DECK TRACTION PAD
CARRY HANDLE
AIR VALVE
LEASH DRING
FIN CLAMP
FIN
VALVE WRENCH
BOARD TOTE
HIGH PRESSURE PUMP
AIR HOSE
REPAIR KIT

QUESTIONS | WARRANTY | PARTS & ACCESSORIES:
1-877-2LEVEL6
[email protected]OM
7

8
SECTION 2 | CARE & MAINTENANCE
Direct sunlight can damage a board if left exposed for a period of time. Heat can
cause the air inside the board to expand beyond the internal pressure limits
of the board. Keep your board in an area with good air ow and circulation.
Leaving your board in a vehicle during the day (closed or open) elevates the
risk for heat related damages.
KEEP IN A WELL VENTILATED, SHADED
AREA WHEN NOT IN USE.
Max pressure is 15 psi. Do not overinate. If inated in cooler early morning
temperatures, inate closer to the lower end of optimal ination range. Inating
at a lower psi will allow for pressure expansion as the outside temperature warms
during the course of the day.
OPTIMAL INFLATION IS 1215 PSI.
MAX PRESSURE IS 15 PSI.
OVERINFLATING YOUR PADDLE BOARD
OR IMPROPER INFLATION/DEFLATION IS
NOT COVERED UNDER WARRANTY!
RINSE SAND AND SALTWATER DEPOSITS
FROM YOUR BOARD AFTER USE.
Sun, sand and saltwater will degrade any man-made material over time. Rinse
o sand and saltwater deposits from your paddle board with fresh water and
store in a cool, dry environment after each use.

9
QUESTIONS | WARRANTY | PARTS & ACCESSORIES:
1-877-2LEVEL6
[email protected]OM
Board bags are intended for transportation protection, not full time storage.
Prolonged storage of a wet board in a wet board bag will have adverse eects on
the nish of your board, leading to the possibility of mold, and osmotic blisters.
Storing your board in a board bag is not the same as placing it in the shade.
Board bags will collect heat and potentially overheat your board.
REGULARLY MAINTAIN THE
HIGH PRESSURE PUMP.
Unscrew the top of the pump and lubricate top edge and
inside of tube.
CLOSE THE VENT BEFORE EACH USE
OPEN THE VENT AFTER EACH USE.
The DUAL-ACTION pump has a volume of capacity of 2000 cm3 and can exert 2
BAR (29 PSI) of air pressure per pump. For added eciency, engage the action
selector to “DOUBLE ACTION” and exert an equal volume of air on both up and
down strokes of the pump.
HIGH PRESSURE PUMP
ACTION
SELECTOR
PRESSUREGAUGE
LUBRICATE
TOP EDGE &
INSIDE OF TUBE

10
SECTION 3 | INFLATION & DEFLATION
Fasten air hose to pressure gauge.
Locate the air valve on tail section of the
board deck and open valve cap.
Turn the colored valve pin counter-clockwise
to the“UP” position. The valve pin will prevent
air from escaping when in the“UP” position.
Connect air hose to air valve and twist 90oto
secure the connection.
Inate to 12-15 psi.
Disconnect air hose from valve and close valve
cap.
Open valve cap.
Depress colored valve pin and turn clockwise
to lock the pin in the“DOWN” or open
position.
Allow air to freely escape Inatable SUP for a
few minutes.
Beginning at the nose, tightly roll up Inatable
SUP to force remaining air through the air
valve.
SUP INFLATION
SUP DEFLATION
DOWN
FOR
DEFLATION
UP
FOR
INFLATION
1.
2.
3.
4.
1.
2.
3.
4.
5.
6.

11
QUESTIONS | WARRANTY | PARTS & ACCESSORIES:
1-877-2LEVEL6
[email protected]OM
Verify the valve pin is in the“UP” position. “UP” keeps air in. “DOWN”allows air out.
Verify the air hose is securely fastened to the air valve.
The air valve may be loose. Refer to“VALVE TIGHTENING”below.
Check for tears and/or cracks. This is best performed in water. Submerge the sup and
look for streams of air bubbles. If a large body of water is not available, try a spray bottle
lled with water and dish soap. Spray the board along the seams and look for billowing
soap bubbles. If a tear/hole is located, refer to“INFLATABLE SUP REPAIRS”in this manual.
If none of these tips resolve the issue, contact us at [email protected].
SUP NOT INFLATING or AIR ESCAPING SUP WHILE INFLATING
TROUBLE SHOOTING LEAKING SUPS
VALVE TIGHTENING
Occasionally, the valve on your inatable SUP may
become loose. If the valve ange freely spins when
opening the valve cover or you detect air leaking from
the valve area, tightening may be required. Using the
included valve wrench, tighten valve in a clockwise
motion until hand tight.
NEVER USE THE VALVE
WRENCH WHEN SUP
IS PRESSURIZED.
VALVE WRENCH

12
SECTION 4 | FIN INSTALLATION
LEVEL SIX INFLATABLE SUPS include a
center stabilizer n and a screw set. We
recommend removing ns after each use
to prevent damage to the n and board.
FINS AND HARDWARE
FIN INSTALLATION
STABILIZER FINSCREW SET
SCREW KEY
1. 2.
3. 4.

13
QUESTIONS | WARRANTY | PARTS & ACCESSORIES:
1-877-2LEVEL6
[email protected]OM
1.
2.
3.
4.
5.
6.
7.
REPAIR KIT
CONTAINER
CEMENT
PVC/POLYESTER
PATCHES X 2
DIRECTIONS FOR USE
BEFORE YOU START
Completely deate paddle board.
Thoroughly clean the surface around the leak and the matte side of the PVC/
Polyester patch with rubbing alcohol. Both surfaces must be free of moisture, oil
and debris.
Open the cement tube by breaking the tube seal using the outside of the tube cap.
Apply cement carefully and evenly to both paddle board surface and matte side
patch surface. Avoid contact with skin & eyes. Avoid breathing cement vapors.
Allow cement on both board and patch to dry to the touch. Once dry, reapply a very
thin layer of cement around the perimeter of the patch.
Once cement on both board and patch becomes tack-free, apply patch to board and
rmly work out any trapped air bubbles.
Allow 8 hours for cement to cure before inating paddleboard.
Prepare the following items:
Latex Gloves (Pair)
Isopropyl Alcohol (Rubbing Alcohol)
Clean Cloth
Cement Applicator (Brush, Popsicle® stick, etc.)
Emergency Repair Kit Contents (Cement + Patches)
WEAR LATEX GLOVES TO AVOID
SKIN IRRITATION.
SECTION 5 | REPAIRS

14
SECTION 6 | TRANSPORTATION TIPS
Inatable SUPs are designed to compact for convenient storage & travel.
Due to a lack of weight when inated, they will travel poorly if strapped to a
vehicle rooftop. Damages incurred by improper transport are not covered by
the manufacturer’s warranty!
When transporting, be sure to clear any sharp objects. Punctures are not
covered by the manufacturer’s warranty!
Keep clear of any heat producing items such as camp stoves, propane lamps,
etc. Damages resulting from heat are not covered by the manufacturer’s
warranty!
Allow your Inatable SUP to completely dry before tightly rolling for packing.
Excess moisture may cause mildew and/or mold damage.
DO NOT TRANSPORT AN INFLATED STAND
UP PADDLE BOARD ON TOP OF A VEHICLE.
The included board tote is intended for Inatable SUP and Inatable SUP
accessories only. Additional items added to the board tote may exceed
weight capacity and result in damages to the tote, shoulder straps and/or
carry handle.
When completely packed, an inatable SUP and its accessories can get rather
heavy. Make sure to never carry more than is comfortable for you in one trip.
Always use proper lifting and carrying techniques to avoid straining muscles.
For maximum comfort when carrying the board tote, wear both shoulder
straps to evenly distribute the carry weight. Tighten the shoulder straps to
reduce slack and to avoid tote contents from resting on the back of the legs.
NEVER CARRY MORE THAN YOU CAN
HANDLE COMFORTABLY.

15
LEVEL SIX OFFERS A LIMITED 365 DAY
WARRANTY AGAINST DEFECTS IN MATERIALS
AND WORKMANSHIP.
TERMS OF WARRANTY:
Your LEVEL SIX product is guaranteed to be free of defects in material and workmanship for a period
of no more than 365 days from the date of purchase. If the product does not conform to the warranty,
LEVEL SIX, at its discretion will issue a new, like new, or similar model product, excluding any shipping
charges.Warranty extends to original purchaser only and is non-transferable. Sales receipt and original
packaging materials are required.
WARRANTY:
LEVEL SIX will make every eort to produce boards to the highest quality and standards in the industry.
We do quality checks in our factories and in our warehouses in North America in an eort to guarantee
each board’s quality before shipping. Because of the nature of surng and paddle boarding we cannot
warranty the performance of any board or shape for individual riders and varying levels of skills and
abilities. Furthermore, we cannot guarantee against damage or breakage and cannot protect or
warranty against circumstances outside of our control. In the event of a new board being removed
from a box and not in good condition please contact the oce for resolution. You will be asked for a
copy of your sales receipt and photos of the damage in question, as well as original packaging material
to verify if damage was due to shipping. If it is deemed a manufacturing or material aw, we will issue
an RMA number. This number along with the damaged product will need to be returned to the closest
warehouse at customer’s expense. Upon physical review, LEVEL SIX will make its nal determination as
to the nature of the damage or aw and issue a replacement product (model depends on availability),
or store credit. Shipping will be the responsibility of the customer. We are not responsible for damage
or defects once the board has been used. Damage is dened as impact with any object or material,
damage due to dropping, loading, unloading, or transport, alterations or modications, repairs, natural
disasters, res, temperatures below 4.4 oC (40 oF), or above 43 oC (110 oF), any further use of a board
once a claim has been reported, transport or storage of a board with a closed air valve, use of a board
in the water with a loose or removed air valve, failure to clean and service air vent valve, storage of a
board in extremely hot or humid conditions including a wet or damp board bag.
RETURNS AND EXCHANGES:
LEVEL SIX will exchange any new, unused product for company credit providing it is accompanied
by an original sales receipt and all original packaging. This will not include any shipping charges or
expenses. Product must be in new condition and will be subject to the inspection of sta.
QUESTIONS | WARRANTY | PARTS & ACCESSORIES:
1-877-2LEVEL6
[email protected]OM
SECTION 7 | LIMITED LIFETIME WARRANTY

www.levelsix.com