LevelOne FCS-1081 User manual

LevelOne
FCS-1081 / FCS-1081A
PoE IP Camera
User Manual
Ver:2.3.0-0812
Copyright (c) 2008 Digital Data Communications Co., Ltd. All Rights Reserved.

Before You Use This Product
The use of surveillance devices may be prohibited by law in your country. The Network
Camera is not only a high-performance web-ready camera but also can be part of a
flexible surveillance system. It is the user’s responsibility to ensure that the operation of
such devices is legal before installing this unit for its intended use.
It is important to first verify that all contents received are complete according to the list in
the "Package Contents" chapter. Take notice of the warnings in “Quick installation
guide” before the Network Camera is installed, then carefully read and follow the
instructions in the “Installation” chapter to avoid damages due to faulty assembly and
installation. This also ensures the product is used properly as intended.
The Network Camera is a network device and its use should be straightforward for those
who have basic network knowledge. The “Troubleshooting” chapter in the Appendix
provides remedies to the most common errors in set up and configuration. You should
consult this chapter first if you run into a system error.
The Network Camera is designed for various applications including video sharing, general
security/surveillance, etc. The “How to Use” chapter suggests ways to best utilize the
Network Camera and ensure proper operations.
For paragraphs preceded by the reader should use caution to understand completely the
warnings. Ignoring the warnings may result in serious hazards or injuries.

ATTENTION
1. All operation please refer to the instruction.
2. Please don’t place the product on unstable desk or bracket.
3. Please avoid any liquid permeate inside of the machine in case damage the product.
4. Before wiring, please follow all electronic safety standards, and using the
recommendable power supply adapter.
5. Do not let the camera aim at sun or other lighting objects no matter the camera is
operating or not, otherwise it might damage the CCD camera permanently.
6. When the product is out of order, please do not try to fix it by yourself, please refer to
the trouble shooting section of this instruction to figure out the problems in advance.
If the problem is not found, please contact us or our authorized dealers directly.
7. All the features and functions are subject to change without notice. Please visit
www.level1.com for the latest ones.

Table of Contents
Before You Use This Product .......................................................................... 2
Package Contents............................................................................................2
Hardware Installation .......................................................................................2
Software Installation.........................................................................................4
Install “IP CamLocator” ................................................................................... 4
Install “IP CamSecure” .................................................................................... 5
How to Use IP CamLocator..............................................................................7
Initial use IP Cam Locator............................................................................... 7
Configuration of Main Console........................................................................ 7
How to Access to the Network Camera..........................................................30
Initial accessing the network camera .............................................................30
Setting............................................................................................................34
Trouble shooting sheet...................................................................................69
Technical Parameters ....................................................................................70
Streaming Video/Audio Solution.....................................................................71
GNU GENERAL PUBLIC LICENSE...............................................................72

Package Contents
FCS-1081 / FCS-1081A
Fixed Lens
Camera Stand
CD Manual/Utility
Quick Installation Guide
Hardware Installation
Depending on the user’s application, an Ethernet cable may be needed.
The Ethernet cable should meet the specs of UTP Category 5 and not
exceed 100 meters in length.
Connect the power adapter jack to the Network Camera before
plugging in to the power socket. This will reduce the risk of accidental
electric shock.
Since FCS-1081/FCS-1081A is a PoE IP camera, it could work without attaching to power outlet as long as
it connects to PoE switch.
The Network Camera will first detect Ethernet. Until the Network Camera is connected to Network, the LED
will become green and flash. Operating in the Network mode, the green LED will flash every second as
heartbeat to indicate alive.
To install in Ethernet
Make sure the Ethernet is firmly connected to a switch hub. After attaching the Ethernet cable plug in the
power adapter if users want to have a redundant power. If the LED turns out to be steady green after
self-test, go to next paragraph “Software Installation”.

To adjust the camera setting
Consult with the dealer of the peripherals for correct installation.
The Network Camera provides the auto iris lens connector. If the
auto iris lens is used, the dip should be adjusted to AI option. And
you also have to select VIDEO drive or DC drive lens by select
correct iris mode. The pin assignment of the auto iris lens connector
is as follows.
Video Drive DC Drive
1. 12V, Power Source 1. DAMP -
2. Not used 2. DAMP +
3. IRIS 3. DRIVE +
4. Ground 4. DRIVE -
BLC / OFF Back Light Control
AES / AI Auto Electronic Shutter or Auto-Iris lens
DD / VD DC drive or VIDEO drive auto-iris lens
LEVEL Brighten or darken the video image
To adjust the lens
There is a fixed lens free bundled. Whereby revolving the lens, it can be focused on. However, users shall
loosen or tighten the gray loop by using the wrench attached in the package.
1.Unscrew it first
2. Loosen or tighten
the gray loop.

Software Installation
In this manual, "User" refers to whoever has access to the Network Camera, and
"Administrator" refers to the person who can configure the Network Camera and grant user
access to the camera.
At the end of the hardware installation, the Administrator must place the product software CD
into the CD-ROM drive of the PC running in MS Windows. An auto-run program will pop up (If
the program is not on auto-run, go to the root directory of the software CD and click on
“autorun.exe”).
Install “IP CamLocator”
Click on “Install Software” item, after the window contains changed, click on “IP
CamLocator” to run installation program.

Upon IP CamLocator’s start up, this program searches for LevelOne’s products on the same
LAN. After searching, LevelOne Video Servers or Network cameras will be located by the IP
CamLocator. There may be several entries shown in the window. The Administrator may
differentiate the Network cameras with the model number and MAC address.
The IP addresses shown in the "IP Address" field reflect those on the local network. They
may be from the DHCP server. If there is no DHCP server, the camera will try to find a free
IP address (this takes from 15 second to 3 minutes, depending on the LAN status). The
method of finding IP address is seeking from 192.168.0.2, to 192.168.0.254. If any of the
address inside this range is free, the Network Camera will be assigned to this IP address, and
its subnet mask would be 255.255.255.0.
Install “IP CamSecure”
Click”Install Software”
Click”IP CamSecure” and follow the onscreen instruction or refer to the user’s manual to
complete installation.

Custom Setup Type:
You may install the system to the directory of your
preference and choose which feature(s) you want to
install to the PC.
Hint: You may, for instance, install only Playback
and/or LiveView on the PC at home or other remote
site from which you do not install the camera but are
going to watch them remotely.

How to Use IP CamLocator
This chapter introduces how to monitor the image from the camera using IP CamLocator.
The LevelOne video server and Network camera can be used with Microsoft web browsers
and IP CamLocator in Windows operation systems. This document focuses on introducing IP
CamLocator.
Initial use IP Cam Locator
Click Start -> Program Files -> LevelOne -> IP Cam Locator -> IP Cam Locator.
Configuration of Main Console
Main Menu

Main Menu
Camera
Click this button to get into common information of all Network cameras in network. You can
connect the specific Network cameras to get life video and to optimize video setting.
User
Click this button to get into user basic setting information of all Network cameras in network.
You can connect the specific Network cameras to get and set basic values. This section
includes Info, User, Date Time, TCP/IP, PPPoE and DDNS.
Note: Only the administrator has access to the Settings.
About
Click this button to get into information of IP CamLocator.
Camera
The Camera page provides you LevelOne network cameras in the network with information,
including product name, IP address, MAC address, model name and model ID. Click on
specific network cameras to optimize Video Setup including brightness, contrast, saturation
and hue.
Search：Click it to search Network Cameras in the network, it displays Network Cameras information
including Name, IP Address, MAC, Mod. Name and Mod. ID.
Note:
If the camera is not located in local network, it will appear in red text. Some information is not available
when the IP camera is not in local network.
The IP addresses shown in the "IP Address" field reflect those on the local network. They may be from
the DHCP server. If there is no DHCP server, the video server will try to find a free IP address (this
takes from 15 second to 3 minutes, depending on the LAN status). The method of finding IP address is

seeking from 192.168.0.2, to 192.168.0.254. If any of the address inside this range is free, the Network
Video server will be assigned to this IP address, and its subnet mask would be 255.255.255.0.
Link to IE：After searching Network Cameras in network, you can click to specific Network Cameras in
search area and press Link to IE to use IP cameras with Microsoft web browses.
Setup
Choose a network camera, click on Setup to change the configurations. You
have to key in the username and password of the administrator to enter the setup page.
The following screen will display:
Note:
For IP cameras not in local network area (which appears in red in the search screen), you can still use
setup to change the configurations of these cameras.
System Information: The system information is displayed.
Press “Next” to continue, “Previous” to go back, “Cancel” to go to the main page.

Account settings: The account setting is displayed. You can change the account setting here.
Press “Next” to continue, “Previous” to go back, “Cancel” to go to the main page.

Date/Time settings: You can set the date/time of the network camera here. See ”Hint” for details.
Press “Next” to continue, “Previous” to go back, “Cancel” to go to the main page.

Network settings: You can change the network settings of the network camera here. See “Hint” for details.
Press “Next” to continue, “Previous” to go back, “Cancel” to go to the main page.

PPPoE settings: You can change the PPPoE settings here. See “Hint” for details.
Press “Next” to continue, “Previous” to go back, “Cancel” to go to the main page.

DDNS settings: You can change the DDNS settings here.
Press “Next” to continue, “Previous” to go back, “Cancel” to go to the main page.

Apply settings: Click on “Apply” to use the new settings.
Choose “Reboot system to apply new (network) settings” to reboot after the settings are applied.

Upgrade
Choose a network camera, click on Upgrade to upgrade the firmware. You have to
key in the username and password of the administrator to enter the upgrade page.
The following screen will display:
Choose the firmware image file you want to upgrade and press “Upgrade” to start. The device will
automatically reboot after upgrade.

Factory Default
Choose a network camera, click on Factory default to reset the configurations to
default. You have to key in the user name and password to use the factory default function.
Click on “OK” to continue. The device will automatically reboot after the configurations set to default.