LevelOne WPS-0104 User manual

L
Le ev ve el l O On ne e
P
Pr ri in nt t S Se er rv ve er r
WPS-0104
U
Us se er r G Gu ui id de e
Copyright 2004. ALL RIGHTS RESERVED.
Document Version: 1.2 (April, 2004)
P/N: 9560NT00A0
All trademark and trade names are the properties of their respective owners.

Table of Contents
Chapter 1 Introduction 1
Features......................................................................................................................... 1
Safety Instructions ........................................................................................................ 2
Package Contents.......................................................................................................... 2
Physical Details ............................................................................................................ 3
Chapter 2 LAN Installation 5
Procedure...................................................................................................................... 5
Chapter 3 Wireless Print Server Configuration 7
Overview ...................................................................................................................... 7
Using the Windows Wizard.......................................................................................... 7
Chapter 4 Client PC Configuration 10
Overview .................................................................................................................... 10
Windows Peer-to-peer Printing .................................................................................. 12
Windows SMB Printing.............................................................................................. 19
Windows with Server-based Print Queues ................................................................. 21
Macintosh (AppleTalk)............................................................................................... 22
Macintosh OS X ......................................................................................................... 23
Chapter 5 BiAdmin Management Utility 24
Requirements.............................................................................................................. 24
Installation .................................................................................................................. 24
Operation .................................................................................................................... 24
Chapter 6 Web-Based Management 39
Overview .................................................................................................................... 39
Preparation.................................................................................................................. 39
Connecting to the WPS-0104 LevelOne Wireless Printer Server............................... 40
Configuration Screens ................................................................................................ 40
Chapter 7 Special Features 47
Overview .................................................................................................................... 47
Internet Printing Protocol (IPP) .................................................................................. 47
Internet Mail Printing ................................................................................................. 52
Printing through the Internet....................................................................................... 56
Page i

Chapter 8 Troubleshooting 57
Overview .................................................................................................................... 57
Hardware & Connection Problems............................................................................. 57
AppleTalk (Macintosh)............................................................................................... 58
Windows Printing Problems ....................................................................................... 60
Unix Troubleshooting................................................................................................. 65
Appendix A Specifications 66
General Specifications ................................................................................................ 66
Protocol Support ......................................................................................................... 66
Feature Support........................................................................................................... 66
Regulatory Approvals................................................................................................. 67
Appendix B Windows Server Configuration 69
Windows NT4.0 Server .............................................................................................. 69
Windows 2000/2003 Server ....................................................................................... 70
Appendix C Unix Systems 71
Overview .................................................................................................................... 71
WPS-0104 LevelOne Wireless Printer Server IP Address Configuration .................. 71
Other WPS-0104 LevelOne Wireless Printer Server Configuration........................... 72
LPD Configuration ..................................................................................................... 73
Appendix D NetWare 78
Overview .................................................................................................................... 78
Creating an NDPS Manager Object............................................................................ 78
Creating an NDPS Printer Agent ................................................................................ 79
Page ii

Page 1
Chapter 1
Introduction
This chapter provides an overview of your WPS-0104 LevelOne Wireless Printer
Server's features.
1
Features
Congratulations on the purchase of your new WPS-0104 LevelOne Wireless Printer Server.
Your WPS-0104 LevelOne Wireless Printer Server was designed to provide a simple and
efficient network printing solution. It is packed with features, including:
 Wireless LAN Support. Wireless stations supporting the IEEE 802.11b or IEEE
802.11g standard can interoperate with the WPS-0104 LevelOne Wireless Printer Server.
Both LAN and WLAN users can print to the attached printer or printers.
 Versatility. The WPS-0104 LevelOne Wireless Printer Server supports up to four
protocols: TCP/IP, SMB (Service Message Block), AppleTalk (EtherTalk), and NetBEUI.
It features an Ethernet interface port and operating system support includes Unix, NetWare
(NDPS LPR printing), and Microsoft Windows.
 Easy Installation. The WPS-0104 LevelOne Wireless Printer Server makes adding
printers or plotters to your network simple.
 Easy Setup. A number of utility programs are supplied to simplify setup. For Windows
98SE/Me/NT/2000/XP/2003 Server users, the BiAdmin program makes it easy to
configure the WPS-0104 LevelOne Wireless Printer Server for a variety of network and
server configurations.
 Web-based Interface. The Web-based interface provides an easy method of
configuration in TCP/IP networks, regardless of your client platform.
 Compact Size. This allows the WPS-0104 LevelOne Wireless Printer Server to be used
even where space is limited.
 Remote Management Tools. A variety of software tools are provided. In most
environments, both the WPS-0104 LevelOne Wireless Printer Server and attached bi-
directional printers can be configured remotely.
 Internet Printing Protocol (IPP) Support. The WPS-0104 LevelOne Wireless Printer
Server can act as an IPP (Internet Printing Protocol) Server, allowing clients, suppliers,
colleagues and others to print to your printer from anywhere on the Internet. Windows IPP
Client software is also supplied.

Safety Instructions
For your own safety, and to protect your WPS-0104 LevelOne Wireless Printer Server, please
observe the following safety advice.
1. Unplug this device from its power source before cleaning. Use only a slightly dampened
cloth for cleaning. Do not use liquid or aerosol cleaners.
2. Avoid using this product near water. Exposure to water poses an electric-shock hazard.
3. Do not place the WPS-0104 LevelOne Wireless Printer Server on an unstable surface. The
device may fall causing serious damage to the device.
4. This device should only be used with the power supply type specified on the marking
label. If you are not sure of type of your local power supply, consult your dealer or the
local power company.
5. Do not pinch, crimp or otherwise damage the power cord. If exposed to foot traffic,
ensures that the cable is properly shielded and does not pose a tripping hazard.
6. If using an extension cord, makes sure the total ampere rating of the products using the
cord does not exceed the extension cord's ampere rating.
7. Do not attempt to service this device, as opening or removing casing may expose you to
dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
8. The WPS-0104 LevelOne Wireless Printer Server should be serviced by qualified service
personnel under the following conditions:
• The power cord is damaged or frayed.
• Liquid has been spilled onto the product.
• The product has been exposed to rain or water.
• The product does not operate normally in accordance with the operating instructions.
• The device has been dropped or the casing has been damaged.
Package Contents
You should find the following items packaged with your WPS-0104 LevelOne Wireless Printer
Server. If any items are missing, contact your dealer immediately.
• The WPS-0104 LevelOne Wireless Printer Server.
• Power Adapter.
• One CD-ROM containing all support programs and this manual.
• Quick Install Guide.
Page 2

Physical Details
This section has details of the LEDs and connectors. Further details are contained in Appendix
A - Specifications.
WPS-0104 LevelOne Wireless Printer Server
• 1 x USB 2.0 Printer Port
• IEEE 802.11g/802.11b Wireless Station
• 10/100BaseT LAN connection
Figure 1: WPS-0104
Item Description
1 Error LED
2 Status LED
3 USB Connector
4 10/100BaseT Connector.
5 Power input
6 Diagnostic button, see page 4 for details.
Page 3

LED Indicators
There are two (2) LED indicators on the top panel - Status (Green, right) and Error (Red, left).
The LED indicator modes are described in the following table.
Status LED Error LED Status Description
Off Off No Power
On On Hardware error
On Off Normal operation (idle)
Blinking Off Normal operation - data is being transmitted or
received on the USB Printer Port.
Blinking Blinking During a Firmware Upgrade, both LEDs will blink.
Diagnostic Push Button
The WPS-0104 LevelOne Wireless Printer Server is fitted with a Diagnostic Push Button. The
button is recessed; a pin or paper clip can be used to press it. This button has 2 functions:
• Restore the factory default settings
• Print a test page containing all current settings.
To restore the factory default settings:
1. Turn the WPS-0104 LevelOne Wireless Printer Server OFF.
2. Press and hold the diagnostic button. While pressing the button, switch the WPS-0104
LevelOne Wireless Printer Server ON.
3. If you continue pressing the button for 10 seconds, a diagnostic page will be printed,
showing the new (default) settings.
To generate a Diagnostic print out
1. Ensure that both the WPS-0104 LevelOne Wireless Printer Server and the printer attached
to port 1 are ON.
2. Press the diagnostic button, and hold it in for 2 seconds.
3. The test page, containing the current settings, will be printed.
Note:
PostScript printers are unable to print this page. If you have a PostScript printer on Port 1,
the test page will not be printed.
Page 4

Page 5
Chapter 2
LAN Installation
This chapter describes how to install the WPS-0104 LevelOne Wireless Printer Server
in your Local Area Network.
2
Procedure
1. Preparation
• Ensure the power is OFF. Do not connect the WPS-0104 LevelOne Wireless Printer
Server while power is On.
• Find the Default Server Name for your WPS-0104 LevelOne Wireless Printer Server. The
Default Server Name is shown on a sticker on the base of the device. It consists of 8 letters
and/or digits. Record this name; it may be needed during configuration.
2. Connect the Printer or Printers
Connect the printer or plotter cable(s) to the appropriate port(s) on the WPS-0104 LevelOne
Wireless Printer Server unit.
3. Connect to your Network
Wired Network Interface
Connect the network cable to the 10/100BaseT LAN connector on the WPS-0104 LevelOne
Wireless Printer Server.
• To use the LAN interface, the LAN cable needs to be inserted
BEFORE powering ON
• In the default Wireless "Infrastructure" mode, connecting a LAN cable
will disable the Wireless interface. To use both the LAN and Wireless
interfaces, the Wireless mode must be changed to "Ad-hoc".
Wireless Network Interface
Ensure that your Access Point is compatible with the WPS-0104 LevelOne Wireless Printer
Server's default settings:
SSID Null (blank)
The WPS-0104 LevelOne Wireless Printer Server will adopt the SSID used by
the Access Point, unless the Access Point is configured not to broadcast its
SSID.
WEP Disabled.
Because the default Wireless mode is "Infrastructure", you cannot
configure the WPS-0104 LevelOne Wireless Printer Server via the
Wireless interface unless you have an Access Point.

LAN Installation
4. Power Up
Plug in the power adapter cable and power up. Start-up will take only a few seconds.
Use only the Power Supply unit provided with the device. Power Supply units for
different models are not interchangeable.
5. Check the LEDs
Once start-up is complete:
• The Status LED should be On.
• The Error LED should be Off.
Page 6

Page 7
3
Chapter 3
Wireless Print Server
Configuration
This chapter provides an overview of the configuration process.
Overview
The WPS-0104 LevelOne Wireless Printer Server is designed to support many different
platforms, and the configuration required would depend upon the environment in which it is
installed.
• The WPS-0104 LevelOne Wireless Printer Server usually requires configuration, but if
there's a DHCP server on your network, then the device is just plug-and-play. A Windows-
based setup Wizard is also provided on the CD-ROM to simplify this task.
• PCs wishing to use the printer attached to the WPS-0104 LevelOne Wireless Printer
Server always require configuration. See Chapter 4- Client Configuration for details.
• If you wish to use a queue-based printing system using Windows NT Server/Windows
2000/Windows XP, the Network Server must be configured as detailed in Appendix B -
Windows Server Configuration. However, it is not necessary to use a Network Server-
based queue; client PCs can print directly to the WPS-0104 LevelOne Wireless Printer
Server using the Peer-to-peer Printing installed by the User setup option on the CD-ROM.
Configuration Methods
The following methods are available to perform the required Print Server configuration:
• Windows-based Wizard - see below for details.
• BiAdmin management utility program - see Chapter 5 for details.
• Web-based setup - see Chapter 6 for details.
Advanced Configuration and Management
The BiAdmin management utility is provided for advanced configuration and management.
This program is installed by default when the Administrator install option is chosen. See
Chapter 5 for details on using BiAdmin.
Using the Windows Wizard
The Windows-based Wizard is supplied on the CD-ROM, and runs on Windows 98SE, NT4.0,
ME, Windows 2000, Windows XP and Windows Server 2003.
Using this Wizard is the recommended method to configure the Print Server.
It can be used configure the WPS-0104 LevelOne Wireless Printer Server for your Network
environment, even if the Print Server does not have a valid IP address.
Procedure
1. Insert the supplied CD-ROM into your drive. If the setup program does not start
automatically, run SETUP.exe in the root folder.
2. On the first screen, shown below, click Setup Wizard.

Figure 2: WPS-0104 LevelOne Wireless Printer Server Screen
3. Click Next on the first screen of the Wizard, to view a list of WPS-0104 LevelOne
Wireless Printer Servers on your LAN.
4. Select your new WPS-0104 LevelOne Wireless Printer Server, then click Next to continue.
5. Enter the required data on the following screen.
• Name of the Print Server can be changed if you wish.
• Comment is optional.
• Select or enter the Workgroup name for this WPS-0104 LevelOne Wireless Printer
Server.
6. Click Next to configure the TCP/IP Screen:
• Select Obtain IP Address automatically if your LAN has a DHCP Server, otherwise
select Fixed IP Address.
• For Fixed IP Address, enter an unused address from the range used on your LAN, or
click the Suggest New Values Button.
Use the same Network Mask and Gateway as PCs on your LAN.
7. On the Wireless Screens, the settings should be set to match your other Wireless Stations.
For details about each setting, refer to the following section Wireless Configuration.
8. Click Finish to save the data to the WPS-0104 LevelOne Wireless Printer Server.
Note: To install the Wizard on your PC, use the "Installation" option.
If the desired WPS-0104 LevelOne Wireless Printer Server is not listed:
• Check all cables to the WPS-0104 LevelOne Wireless Printer Server.
• Check that the WPS-0104 LevelOne Wireless Printer Server's Error LED is Off. If it is
On, restart the Print Server.
• Check that your PC and the WPS-0104 LevelOne Wireless Printer Server are on the same
LAN segment. (If you don't have a Router or Gateway on your LAN, you only have 1
segment.)
• Check that your PC has either the TCP/IP or NetBEUI network protocols installed. See
Checking your Network Protocols in Chapter 4for details.
Page 8

Wireless Configuration
Wireless Mode
The WPS-0104 LevelOne Wireless Printer Server is a Wireless station, NOT an access point.
Like other Wireless stations, they have 2 modes:
• Ad-Hoc mode - no Access Point is used, Wireless stations communicate directly with
each other. Each Wireless station should be set to use the same Channel, although some
Wireless stations will scan all channels to find compatible ad-hoc groups they can join
• Infrastructure (Default) - all Wireless stations connect to the Access Point. This allows
connection to both other Wireless stations and the wired LAN.
To use both the LAN and Wireless interfaces, the Wireless mode
must be set to "Ad-hoc".
In "Infrastructure" mode, connecting a LAN cable will disable the
Wireless interface.
Required Configuration
Ad-hoc Mode Infrastructure Mode
SSID The 802.11g Wireless Print Server will
join any group with the same SSID.
If there's no Ad-Hoc group available,
the 802.11g Wireless Print Server will
create the group using the SSID
assigned to it.
Must match the Access Point.
Channel The 802.11g Wireless Print Server will
join any group with the same Channel
number.
If there is no existing Ad-Hoc group
available, the 802.11g Wireless Print
Server will create the group using its
own Channel number.
Access Point sets the Channel
used.
Wireless stations
automatically locate the
correct channel.
WEP Settings Must match the other Wireless stations. Must match the Access Point.
Page 9

Page 10
Chapter 4
Client PC Configuration
The chapter details the client configuration required on LAN clients to use the printer
or printers attached to the WPS-0104 LevelOne Wireless Printer Server.
4
Overview
Before performing client configuration, the WPS-0104 LevelOne Wireless Printer Server must
be installed on your LAN, and configured as described in Chapter 3. Both the WPS-0104
LevelOne Wireless Printer Server and the attached printer must be powered ON.
Printing Methods
The WPS-0104 LevelOne Wireless Printer Server supports a number of printing methods:
• Peer-to-peer Printing means that the print jobs are stored (queued) on your PC, and sent
directly to the WPS-0104 LevelOne Wireless Printer Server when it is available.
• Server-based Print Queue means that all print jobs are stored (queued) on the Network
Server (e.g. Windows NT/2000) and then sent to the WPS-0104 LevelOne Wireless
Printer Server. This allows the Network Administrator to modify the Print Queue. For
example, an important job can be moved to the head of the queue.
• Windows SMB printing is a Microsoft standard for using a "Network Printer". No
additional software needs to be installed on your Windows PC, and printing from MS-
DOS programs is supported. However, because the WPS-0104 LevelOne Wireless Printer
Server can not store files, large print jobs may cause problems.
• AppleTalk is also supported, and normally no configuration of the WPS-0104 LevelOne
Wireless Printer Server is required. See the Macintosh section of this chapter for details of
client configuration.
Which printing method should I use?
• If using Windows 98SE, NT, Me, 2000, or XP, the easiest method to use is Peer-to-peer
Printing.
• If using Windows, and you need to print from MS-DOS programs, or you don't wish to
install additional software, use SMB.
However, SMB is not suitable for large, complex documents, so if you need this as well as
MS-DOS printing, you should install BOTH Peer-to-peer Printing and SMB printing. MS-
DOS programs can use the SMB printer, Windows programs should use Peer-to-peer
Printing.
• If your LAN has Network Servers (e.g. Windows NT, Windows 2000 Server) use the
method advised by your Network Administrator. The WPS-0104 LevelOne Wireless
Printer Server can print via a queue located on a Network server, if desired.
• Unix users - refer to Appendix C.
• Macintosh users - refer to the Macintosh section of this chapter.

Checking your Network Protocols (Windows 9x)
Your PC must have EITHER the TCP/IP or NetBEUI protocols installed.
• If using the Peer-to-peer Printing, the installation program will check this for you.
• If using other methods, you must check manually, as follows:
1. Select the Settings - Control Panel - Network option on the Start Menu. You should see a
screen like the one following:
Figure 3: Network Configuration
• The top line in the list (NetBEUI -> PCI Fast Ethernet Adapter) indicates that the
NetBEUI protocol is installed on this PC. Your PC will show the name of the your
Network card rather than "PCI Fast Ethernet Adapter".
• The highlighted line (TCP/IP -> PCI Fast Ethernet Adapter) indicates that TCP/IP is
installed. Your PC will show the name of the your Network card rather than "PCI Fast
Ethernet Adapter".
2. If neither line is present:
• Install the NetBEUI protocol by selecting Add - Protocol - Microsoft - NetBEUI - OK.
You may be prompted for your Windows CD-ROM.
This protocol requires no configuration.
• If required, you can also install TCP/IP. However, depending on your LAN
environment, TCP/IP may require further configuration.
3. If either protocol is already installed, proceed with installation.
Page 11

Windows Peer-to-peer Printing
With this printing method, print jobs are stored (queued) on your PC, and then sent to the
WPS-0104 LevelOne Wireless Printer Server when it is available.
Figure 4: Peer-to-Peer Printing
Windows 2000 & XP require no additional software.
For other versions of Windows, the supplied PTP (Peer-to-Peer) Printer Port software must be
installed on each PC.
Windows 2000/XP Setup
The recommended printing method is to use LPR, as follows:
1. Open your Printers folder, right-click the desired printer and select Properties.
2. Select the Ports tab and click the Add Port button.
Figure 5: Printer Ports Screen
Page 12

3. Choose Standard TCP/IP Port, then click New Port.
Figure 6: Add Port Screen
4. On the Add Standard TCP/IP Printer Port screen above, enter the IP Address of the Print
Server in the Printer Name or IP Address field, then click Next.
Figure 7: Additional Port Information Screen
5. On this screen, select Custom, and click the Settings button.
Page 13

Figure 8: Port Settings Screen
6. On the Port Settings screen, shown above:
• Select LPR in the Protocol section
• Enter a Queue name (L1 for the USB Port)
• Ensure the LPR Byte Counting Enabled setting is Enabled.
• Click OK to confirm your changes and close this screen.
7. Follow the prompts to complete the Wizard.
Page 14

Windows 9x/ME Setup
Before performing the following procedure, the WPS-0104 LevelOne Wireless Printer Server
must be installed on your LAN, and configured as described in Chapter 3. Both the WPS-0104
LevelOne Wireless Printer Server and the attached printer should be powered ON.
1. Insert the supplied CD-ROM into your drive. If the setup program does not start, run
SETUP.exe in the root folder.
2. Click Installation button, then select the User Install.
Figure 9: Installation Screen
3. Follow the prompts to complete the installation of the Peer-to-peer Printer Port Driver.
(Refer to the Windows section of Chapter 8 - Troubleshooting if there is a problem with
the installation.)
4. The Print Driver Setup will then run.
In future, you can use Start - Programs - PrintServer Driver - Printer Port Setup to run the
program again.
PTP Printer Port Setup
1. The program will search for Printer Servers on the network, and a screen like the
following will be displayed.
• If desired, click Refresh.
• The name of the attached printer will be displayed if possible. If "No printer" is
displayed, check that the printer is properly connected and powered on.
Page 15

Figure 10: Print Port Setup (Peer-to-peer Printing)
If your WPS-0104 LevelOne Wireless Printer Server is not
listed:
• Click the "Refresh" button.
• Check that both the WPS-0104 LevelOne Wireless Printer Server and the
printer are properly connected, and powered on.
• Check that the WPS-0104 LevelOne Wireless Printer Server has been
configured. (Use the Setup Wizard on the CD-ROM.)
• If using TCP/IP, try installing the NetBEUI protocol. (See the earlier section
Checking your Network Protocols for details.). Then try again.
2. Select the desired port on a WPS-0104 LevelOne Wireless Printer Server, then click Next.
A pop-up message will inform you if the port has been created successfully.
If you see the following error message, either install Internet
Explorer 4 or later, or follow the procedure in the "Trouble
Shooting - Windows" section of Chapter 8.
3. The printer port will be created, then a screen like the following will be displayed.
Page 16

Figure 11: Configure Printer Port
4. Select the correct Windows printer in the Existing Printers list, and click the Connect
button.
If the correct printer type is not listed, click "Add New Printer" to run the Windows Add
Printer wizard. Step through the Wizard and install the required printer:
• Select the correct Printer Manufacturer and Model, or use the "Have Disk" option if
appropriate.
• We recommend changing the Printer name to indicate which device is on.
(e.g. HP2100 on SCA43600_P1)
• If prompted about Sharing the printer, do NOT enable Sharing.
• When the Printer installation is finished, it will be listed in the Configure Printer Port
screen above. Select it and click Connect.
5. Installation is now complete. You can now print using this printer.
• To install additional Printers, repeat steps 4.
• Use the Start menu to run this program in future. The default installation is Start -
Programs - PrintServer Driver - Print Driver Setup.
Note:
If using the Epson Spooler Manager, this program must be disabled, as follows:
1. Run the Epson Spooler Manager.
2. Select "Queue Setup" from the menu.
3. Click "Use Print Manager for this port".
4. Click "OK" to exit.
Management
• Print jobs can be managed like any Windows printer. Open the Printers folder (Start -
Settings - Printers) and double-click any printer to see the current print jobs.
• If the printer attached to the WPS-0104 LevelOne Wireless Printer Server is changed, just
run this program again, and select the correct printer.
• To delete a port created by this setup program, use the Windows Delete Port facility:
• Right-click any printer in the Printers folder, and select Properties.
Page 17