LevelOne CamCon FCS-4020 User manual

LevelOne
Installation Guide
FCS-4020
Day & Night
Speed Dome Network Camera
Ver 1.0

1
Warning Before Installation
Contact your distributor in the
event of occurrence.
Refer to your user’s manual for the
operating temperature.
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Do not touch the Network Camera
during a lightning storm.
Do not disassemble the Network
Camera.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.
Do not manually pan and tilt the
Network Camera when the power is
on.

2
Package Contents
1
Power Adapter
or
Software CD
FCS-4020
Warranty Card
Black Cover / Dome Cover
Wall Mount Bracket
RJ45 Female/Female Coupler Quick Installation Guide
O-ring and Screws /
Alignment Sticker
Silica Gel / Metal Ring
Silica gel
Silica gel

3
Inner View
Reset Button
Lens
Outer View
Physical Description
2
Status LED
Ethernet 10/100
RJ45 Plug
Audio Out (green)
Microphone In (pink)
Power Cord Socket (black)
General I/O
Terminal Block
Ground
SD Card Slot

4
Hardware Installation
3
Mounting the Network Camera
1. Attach the alignment sticker to the wall.
2. Drill four pilot holes into the wall.
3. Attach the black cover to the Network Camera using the supplied four black
screws.
4. Stick the supplied two pieces of silica gel symmetrically to the inner side of the
dome cover. Then place the metal ring into the dome cover to x the silica gel.
5. Fix the dome cover to the Network Camera and secure it by rotating it clockwise.
6. Loosen the three screws on the front opening of the wall mount bracket.
7. Place the O-ring on the front opening of the wall mount bracket.
8. Feed the cables through the front opening of the wall mount bracket and pull them
from wall outlet.
9. Attach the Network Camera to the wall mount bracket by tightening the three
screws on the front opening of the wall mount bracket.
10. Fasten the wall mount bracket to the wall.
1
2
3
5
6
7
8
9
10
Silica gel
Silica gel
4

5
Network Deployment
4
P
OWE
RC
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
1. If you have external devices such as
sensors and alarms, connect them to
the general I/O terminal block.
2. Use the supplied RJ45 female/female
coupler to connect the Network Camera
to a switch.
Use Category 5 Cross Cable when
Network Camera is directly connected
to PC.
3. Connect the power cable from the
Network Camera to a power outlet.
GND: Ground
DI4: Digital Input
DI3: Digital Input
DI2: Digital Input
DI1: Digital Input
GND: Ground
N.O. : RELAY_NO
COM. : RELAY_COM
+12V : Power, 12V DC
(AC 24V 2A)

6
1. Install "Installation Wizard " from the Software Utility directory on the software CD.
2. The program will search for LevelOne Network Cameras on the same LAN.
3. After searching, the main installer window will pop up. Click on the MAC that matches
the one labeled on the side of the camera lens or S/N number on the label of carton
to connect the Internet Explorer to the Network Camera.
Assigning IP Address
5
Power : AC24V/2A
FCS-4020 H/W Ver:1.0
MAC:00116B80F13E
S/N:YYMMDDXXXXX
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
00-11-6B-80-F1-3E 192.168.3.143 FCS-4020
00116B80F13E
N18085
Power : AC24V/2A
FCS-4020 H/W Ver:1.0
MAC:XXXXXXXXXXXX
S/N:YYMMDDXXXXX
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.

7
For further setup, please refer to the user's manual on the software CD.
Ready to Use
6
1. Access the Network Camera from the Internet.
2. Retrieve live video through web browsers or recording software.