LevelOne Infinity IES-0822 User manual

4 x 802.3af + 3 FE+ 1 MM SC Unmanaged Switch
Quick Installation Guide
IES-0822
4 x 802.3af + 3 FE+ 1 MM SC Unmanaged Switch
-
40 to 75C, DIN
rail
Quick Installation Guide
40 to 75C, DIN
-
Quick Installation Guide
v1.00 - 1206
IES-0822 Page 1
Overview
LevelOne IES-0822 Industry Ethernet Switch provides 44 PoE
ports of 10/100Base-TX plus 3 ports of 10/100Base-TX
Ethernet plus 1 port 100FX Multimode SC fiber to enable high
speed network at mission-critical environment. This device is
designed to be mounted on an industry standard DIN-rail, plus
the clearly visible status LEDs provide simple monitoring of port
link activity.
Power over Ethernet
This switch is Power Sourcing Equipment (PSE), and it is fully
complied with IEEE 802.3af PoE standard at maximum 15.4W
power budget per port. It helps to save infrastructure wiring
costs dramatically by eliminating electric wiring and less UPS
needed.
High Reliability
All components are built to withstand harsh environment
applications without compromise where humidity, temperature
variation and even shock vibration are concerns, including
Electric & Utility, Critical Infrastructure, Transportation and
Surveillance Security. This device operates under -40 to 75
Celsius (-40 to 167 Fahrenheit) temperature.
IES-0822 Page 2
Features
•Meets NEMA TS1 & TS2 environmental requirements for traffic control
equipment.
•Meets IEC61000-6-2 EMC Generic Standard Immunity for industrial
environment.
•Supports IEEE802.3af Power over Ethernet (PoE) Power Sourcing
Equipment (PSE).
•Supports IEEE802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps,
Full/Half-duplex, Auto-Negotiation, Auto MDI/MDIX.
•100Base-FX: Multi/Single mode SC or ST type, WDM Single mode SC
type.
•Supports 1024 MAC addresses. Provides 1M bits buffer memory.
•Alarms for power and port link failure by relay output.
•Power Supplies: Redundant 48VDC Terminal Block power inputs and
48VDC DC JACK with 100-240VAC external power supply.
•Operating voltage and Max. current consumption: 1.5A @ 48VDC. Power
consumption: 72W Max.
•-40℃to 75℃(-40℉to 167℉) operating temperature range
•Tested for functional operation @ -40℃to 85℃(-40℉to 185℉)
• Supports DIN-Rail, Panel, or Rack Mounting installation
Package Contents
IES-0822
Quick Installation Guide
CD User Manual
IES-0822
LED Status
LED
Status
PW 1,2,3 Steady
Off
10/100Base
-
TX or 100Base
LNK/ACT
(Green)
Steady
Flashing
LED Status
Status
Description
Power On
Power Off
TX or 100Base
-
FX/BX
Network connection is established
Flashing
Transmitting or Receiving data
Page 3
Description
Network connection is established
Transmitting or Receiving data

IES-0822
Power Input
Terminal Block
PW1
PW2
Earth Ground
Relay Output
1.
The relay contact closes if Power1 and Power2 are both failed but Power3
on.
2.
The relay contact closes if Power3 is failed but Power1 and Power2 are both
on.
PW3: 48VDC
DC Jack
Power Input
+
48VDC
–
Power Ground
+
48VDC
–
Power Ground
Earth Ground
Relay Output
The relay contact closes if Power1 and Power2 are both failed but Power3
The relay contact closes if Power3 is failed but Power1 and Power2 are both
DC Jack
Input
Page 4
The relay contact closes if Power1 and Power2 are both failed but Power3
The relay contact closes if Power3 is failed but Power1 and Power2 are both
IES-0822
DIN Rail Mount
•
Assembly: Place the switch on the
the slot. Push the front of the switch toward the mounting
surface until it audibly snaps into place
•Start-
up: Connect the supply voltage to start up the switch
via the terminal block (or DC JACK)
•
Dismantling: Pull out the lower
switch from the DIN rail.
DIN Rail Mount
Assembly: Place the switch on the
DIN rail from above using
the slot. Push the front of the switch toward the mounting
surface until it audibly snaps into place
up: Connect the supply voltage to start up the switch
via the terminal block (or DC JACK)
Dismantling: Pull out the lower
edge and then remove the
switch from the DIN rail.
Page 5
DIN rail from above using
the slot. Push the front of the switch toward the mounting
up: Connect the supply voltage to start up the switch
edge and then remove the
IES-0822
10/100Base
The following lists the
Pin
PoE
Port
1
Output Transmit Data +
2
Output Transmit Data
3
Input Receive Data +
4 NC
5 NC
6
Input Receive Data
7 NC
8 NC
10/100Base
-
TX Connector
The following lists the
pin-out of 10/100Base-
TX ports.
(1 to 4)
Standard Port (5)
Output Transmit Data +
Input Receive Data +
Output Transmit Data
- Input
Receive Data
Input Receive Data +
Output Transmit Data +
NC
NC
Input Receive Data
-
Output Transmit Data
NC
NC
Page 6
TX Connector
TX ports.
Standard Port (5)
Input Receive Data +
Receive Data
-
Output Transmit Data +
Output Transmit Data
-
IES-0822
100Base
-
WDM 100Base
Connection
-
FX Connection
The Tx
(transmit) port of device I
is connected to the Rx (receive)
port of device II, and the Rx
(receive) port of device I to the
Tx (transmit) port of device II.
WDM 100Base
-BX
Connection
Only one optical fiber is required
to transmit and receive dat
Page 7
FX Connection
(transmit) port of device I
is connected to the Rx (receive)
port of device II, and the Rx
(receive) port of device I to the
Tx (transmit) port of device II.
Only one optical fiber is required
to transmit and receive dat
a