LevelOne WBR-6022 User manual

LevelOne
WBR-6022
HomeGuard 22 Residential Router
Quick Installation Guide
English Português
Deutsch Svenska
Français Slovenščina
Español 繁體中文
Nederlands 한국어
Dansk Русский
Italiano Polski
Ελληνικά

2
Table of Contents
English .......................................................................................... 3
Deutsch ....................................................................................... 19
Français ...................................................................................... 35
Español ....................................................................................... 51
Nederlands.................................................................................. 67
Dansk .......................................................................................... 83
Italiano......................................................................................... 99
Ελληνικά.................................................................................... 115
Português.................................................................................. 131
Svenska .................................................................................... 147
Slovenščina............................................................................... 163
繁體中文.................................................................................... 179
한국어........................................................................................ 195
Русский..................................................................................... 211
Polski......................................................................................... 227
Default Settings
IP Address 192.168.0.1
Username admin
Password password
Wireless Mode Enable
Wireless SSID LevelOne
Security None
This guide covers only the most common situations. All detailed
information is described in the user manual.

3
Installation
1. Connect your ADSL/Cable modem’s internet line to
WBR-6022’s WAN port.
2. Connect LevelOne IP Cameras, FNS-1020v2 and your PC to
WBR-6022’s LAN ports.
3. Plug-in the Power Adapter.
English
WAN
LAN
Power
FNS-1020v2 IP Camera IP Camera
PC
ADSL/Cable Modem
* If you want to use WPS (WiFi Protected Setup) function for wireless
devices, please refer to page 57 on CD User Manual.

4
Check Your Network Settings
1. Please make sure your PC can get IP address automatically
so the WBR-6022 can communicate with your PC during
configuration.
Select “Control Panel” > “Network Connections”.
Right click the “Local Area Connection” and choose
“Properties”.
Select the TCP/IP protocol for your network card.
Click on the Properties button. You should then see the
following screen and make sure you have selected
“Obtain IP address automatically”
2. Reboot computer to make sure you have received the IP
address correctly form the Router.
1.
2.
3.
4.
5.

5
Easy Setup Wizard
Insert the CD into your CD-ROM drive of your computer.

6
Select Easy Setup Language.
The “Quick” wizard will guide you through the setup in few easy
steps. Details read Page.14 (chart 4) of User Manual.
1.
2.

7
Make sure that your hardware connections are all correct.
Adjust the Router’s time zone.
1.
2.

8
Setup the Power Management schedule.
Click to “enable” the Smart Schedule then click “next” to continue.
Set wireless enable or disable.
1.
2.
2.
1.

9
Configure the wireless setting.
Auto detect Router’s WAN Service.

10
There are 2 examples for WAN service.
Example 1: Auto Detect WAN Setting“PPPoE” or “Dynamic IP”
Step1: Type in your PPPoE account.
Please check your PPPoE account from your ISP, then type in the
data.
Notice: If you use “Dynamic IP”, please ignore Step1.
1.
2.

11
Step 2: Confirm your settings.
Step 3: Save Settings.

12
Step 4: WAN Service Test.
Step 5: Setup Completed.

13
Example 2: if you using another WAN service, please click “Let me
select WAN service by myself”.
Please check your WAN service from your ISP, then type in the
data.
1.
2.

14
Setup HomeGuard
1. Open IE Browser, type in the IP address http://192.168.0.1.
2. Default username and password is “admin” and
“password”.
1.
2.
1.
2.

15
3. Click “Search New Device”.
4. Model Name & Default username / password.
Model Name Username / Password
FCS-0010 / WCS-0010 “administrator” / *blank
FCS-0020 / WCS-0020 “administrator” / *blank
FCS-1030v2 / WCS-2030v2 “root” / *blank
FCS-1060 / WCS-2060 “root” / *blank
FCS-1081A / FCS-1101 “root” / **MAC address
FCS-1091 / WCS-1090 “administrator” / *blank
FCS-0030 / WCS-0030 “admin” / “admin”
*blank: leave the password by blank
**MAC address: Camera’s MAC in capital letters

16
5. “Register” will guide you through few steps to register your
camera(s) and NVR(s).
1. Open “Save as” and choose IPCam 1/2/etc. 2. Insert
Username & password 3. Open “Save as” and choose
NVR1/2/etc. 4. Click “Register”.
Adjust Home Guard’s Time Zone and Save.
1.
4.
3.
2.
2.
1.
Step 2
Step 1

17
6. Set Level1DNS Domain Name.
Click “System” “DDNS Alias”.
You can use a preferred name as Alias, then you can use new
Level1DNS name through the internet anywhere.
The format is “Alias name“.level1dns.net
1. Input Alias name 2. Test alias 3. Save/Modify alias.
2.
1.
3.
2.
Step 3
1.

18
7. View the camera’s live video.
Step 1: Click the IP Camera on the left list.
Step 2: Show the Camera live Video.
Details setup please read Page.22 (chart 4.2) of User Manual.
Notice: if you don’t see the video, please install the Active-X
plug-in for the IP Camera first.
1.
2.

19
Installation
1. Verbinden Sie das Internetkabel Ihres ADSL/Kabel-Modem
mit dem WAN-Port des WBR-6022.
2. Verbinden Sie die LevelOne IP-Kamera(s), FNS-1020 und
den Computer mit den LAN-Ports des WBR-6022.
3. Schliessen Sie das Netzteil an.
Deutsch
WAN
LAN
Power
FNS-1020v2 IP-Kamera IP-Kamera
PC
ADSL/Kabel Modem
* Wenn Sie die WPS (WiFi Protected Setup) - Funktion für drahtlose Geräte
verwenden möchten, lesen Sie bitte auf Seite 60 des CD-Benutzerhandbuch
nach.

20
Prüfen Sie Ihre Netzwerk-Einstellungen
1. Bitte stellen Sie sicher, dass Ihr PC die IP-Adresse
automatisch empfangen kann, so dass der WBR-6022 mit
Ihrem PC während der Konfiguration kommunizieren kann.
Wählen Sie “Control Panel” > “Network Connections”.
Rechter Mausklick auf “Local Area Connection” und
wählen Sie bitte “Properties”.
Wählen Sie “TCP/IP protocol” für Ihre Netzwerk-Karte.
Klicken Sie auf die “Properties”-Taste. Sie sollten dann
den folgenden Bildschirm sehen. Stellen Sie bitte sicher,
dass Sie “Obtain IP address automatically” ausgewählt
haben.
2. Starten Sie Ihren Rechner neu, um sicherzustellen, dass Sie
die IP-Adresse vom Router korrekt empfangen haben.
1.
2.
3.
4.
5.