LevelOne WBR-6804 User manual

1
LevelOne
User Manual
Ver. 1.0
WBR-6804
150Mbps Wireless Dual-WAN 3G Router

2
Safety
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. The user could
lose the authority to operate this equipment if an unauthorized change or
modification is made.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
CE Declaration of conformity
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55022 class B for ITE, the essential protection requirement of
Council Directive 89/336/EEC on the approximation of the laws of the Member
States relating to electromagnetic compatibility.
CE Marking Warning
Hereby, Digital Data Communications, declares that this product is in compliance
with the essential requirements and other relevant provisions of Directive
1999/5/EC.
The CE-Declaration of Conformity can be downloaded at:
http://www.levelone.eu/support.php

3
General Public License
This product incorporates open source code into the software and therefore falls
under the guidelines governed by the General Public License (GPL) agreement.
Adhering to the GPL requirements, the open source code and open source
license for the source code are available for free download at
http://global.level1.com.
If you would like a copy of the GPL or other open source code in this software on a
physical CD medium, LevelOne (Digital Data Communications) offers to mail this
CD to you upon request, for a price of US$9.99 plus the cost of shipping.

4
Table of contents
CHAPTER 1 INTRODUCTION..............................................................................................5
1.1 PACKAGE LIST............................................................................................................5
1.2 HARDWARE INSTALLATION......................................................................................5
CHAPTER 2 GETTING STARTED WITH EASY SETUP UTILITY.......................................8
2.1 EASY SETUP BY WINDOWS UTILITY...............................................................................8
2.2 EASY SETUP BY CONFIGURING WEB PAGES............................................................ 13
YOU CAN ALSO BROWSE WEB UI TO CONFIGURE THE DEVICE.................................. 13
CHAPTER 3 MAKING CONFIGURATION ........................................................................ 17
3.1 BASIC SETTING............................................................................................................... 17
3.2 FORWARDING RULES.................................................................................................... 35
3.2.1 VIRTUAL SERVER........................................................................................................ 36
3.2.2 SPECIAL AP.................................................................................................................. 38
3.2.3 MISCELLANEOUS ........................................................................................................ 39
3.3 SECURITY SETTING........................................................................................................ 40
3.4 ADVANCED SETTING...................................................................................................... 47
3.5 TOOL BOX........................................................................................................................ 56
CHAPTER 4 . TROUBLESHOOTING................................................................................ 61
APPENDIX A. SPEC SUMMARY TABLE.............................................................................. 65
APPENDIX B. LICENSING INFORMATION .......................................................................... 66
Default Settings
IPAddress
192.168.1.1
Password
admin
Wireless Mode
Enable
Wireless SSID
LevelOne
Wireless Security
None

5
Chapter 1 Introduction
The Wi-Fi Combo Router is a high-performance tool that supports wireless networking at home,
work, or in a public place. The Wi-Fi Combo Router supports a USB 3G modem card, either
WCDMAor EVDO and even HSDPA as well, and supports wireless data transfers up to 150M bps,
and wired data transfers up to 100 Mbps. The WiFi Combo Router is compatible with industry
security features.
1.1Package List
WBR-6804
Power Adapter
RJ-45 LAN Cable
Quick Installation Guide
CD Manual/QIG
Antenna
1.2 Hardware Installation
A. Hardware configuration
LED Indicators
Power LED
Antenna
Reset Button
Mobile LED
WAN LED
WiFi LED
LAN LED
WPS Button

6
B. LED indicators
LED Indicator Description
USB 3G Green and Steady On USB 3G connection is established
Green and Blinking Data packet transferred via USB 3G
Ethernet WAN Green and Steady On Ethernet WAN connection is established
Green and Blinking Data packet transferred via Ethernet WAN
WiFi/WPS
Green and Blinking Data packet transferred via WiFi
Green and Blinking In WPS PBC mode
OFF WiFi radio is disabled
Ethernet LAN 1~4 Green and Steady On Ethernet LAN connection is established
Green and Blinking Data packet transferred via Ethernet LAN
Power JACK
WAN PORT
LAN PORT
USB PORT
LED Indicators
Power LED

7
C. Installation Steps
Note:
DO NOT
connect the router to power
before performing the installation steps below.
Step 1.
Plug a USB modem into USB port.
Step 2.
Insert RJ45 cable into LAN Port on the back panel of
the router. Then plug the other end of into computer.
Step 3.
Plug the power jack into the receptor on the back
panel of the router. Then plug the other end into a wall
outlet or power strip.

8
Chapter 2 Getting Started with Easy Setup Utility
There are two approaches for you to set up the Wi-Fi Combo Router quickly and easily. One is
through executing the provided Windows Easy Setup Utility on your PC, and the other is through
browsing the device web pages and configuration.
2.1 Easy Setup by Windows Utility
Step 1
：
Install the Easy Setup Utility
from the provided CD then
follow the steps to configure
the device.
Step 2
：
Select Language then click
“Next” to continue.
Step 3：
Then click the “Wizard” to
continue.

9
Step 4：
Click “Next” to continue.
Step 5
：
Select Wireless Enable, and
then click “Next” to continue.
Step 6：
Enter SSID, Channel and
Security options, and then
click “Next” to continue.

10
Step 7：
Click” Let me select WAN
service by myself” to select
WAN service manually.
Step 8：
Select 3G Service by clicking
3G icon to continue.
Step 9-1：
Select “Auto-Detection” and
the Utility will try to detect and
configure the required 3G
service settings automatically.
Click “Next” to continue.

11
Step 9-2：
Or you can select “Manual”
and manually fill in the
required 3G service settings
provided by your ISP.
Click “Next” to continue.
Step 10:
Click “Next” to save your
setting.
Step 11：
The Wi-Fi Combo Router is
rebooted to make your entire
configuration take effect.

12
Step 12：
Click “Next” to test the
Internet connection or you
can ignore test.
Step 13
：
Click “Next” to test WAN
Networking service.
Step 14
：
Setup is completed.

13
2.2 Easy Setup by Configuring Web Pages
You can also browse web UI to configure the device.
Browse to Activate the Setup Wizard
Type in the IP Address
(http://192.168.1.1)
Type in the default password
“admin” in the System
Password and then click
‘login’ button.
Select your language.
Select “Wizard” for basic
settings with simple way.
Press “Next” to start the Setup
Wizard.

14
Configure with the Setup Wizard
Step 1
:
Change System
Password.
Set up your system password.
(Default：admin)
Step 2: Select Time Zone
.
Step 3: Select WAN Type.
Choose Auto-Detecting or
Manually to set WAN Type.

15
Step 4: Select Wan Type.
If you want to use 3G service
as the main internet access,
please set the WAN interface
as “Wireless WAN” and the
WAN type as “3G”.
Step 5: 3G Mode.
Select Auto-Detection then
click “Next” to continue.
Step 6: Set up your Wireless
Network.
Set up your SSID.

16
Step 7: Setup your Encryption
Key here, then click”Next” to
continue.
Step 8: Apply your Setting.
Then click Apply Setting.
Step 9:
Click Finish to complete it.

17
Chapter 3Making Configuration
Whenever you want to configure your network or this device, you can access the Configuration
Menu by opening the web-browser and typing in the IPAddress of the device. The default IP
Address is: 192.168.1.1
Enter the default password “admin” in the System Password and then click ‘login’ button.
Then, you can browse the “Advanced” configuration pages for configuring this device.
3.1 Basic Setting

18
3.1.1. Network Setup
1. LAN IP Address: The local IP address of this device. The computers on your network
must use the LAN IP address of this device as their Default Gateway. You can change it
if necessary.
2. Subnet Mask: Input your Subnet mask. (All devices in the network must have the same
subnet mask.) The default subnet mask is 255.255.255.0.
3. Combo WAN Status: Display status of combo WAN. With Combo WAN feature, you
can choose one primary WAN connection, and set another WAN connection for backup.
The combo WAN status will be showed here. Press “Settings” button to configure this
feature.
4. WAN Interface: Select Ethernet WAN or Wireless WAN to continue.
5. WAN Type: WAN type of your Internet connection. You can choose a correct one from
the following options.

19
A. 3G

20
1. WAN Type:Choose 3G for WAN connection.
2. Dial-Up Profile: Please select Auto-Detection or Manual. You can choose “Auto-Detection”,
and the router will try to detect and configure the required 3G service settings automatically.
Otherwise, you can select “Manual”, and manually fill in the required 3G service settings
provided by your carrier or ISP.
3. Country*: select your country.
4. Telecom*: select your telecom.
5. 3G Network*: select the 3G network
6. APN*: APN information for your 3G data card. It will show a value after you choose country
and telecom. You can also change it manually.
7. PIN Code: Enter the PIN Code for your SIM card if required. (Optional)
8. Dialed Number*: It will show a value after you choose country and telecom. You can also
change it manually.
9. Account*: The user name for 3G connection. It will show a value after you choose country
and telecom. You can also change it manually.
10. Password*: The password for 3G connection. It will show a value after you choose country
and telecom. You can also change it manually.
11. Authentication*: Choose authentication of 3G connection. You can leave it as “Auto” if you
are not sure.
12. Primary DNS*: You can assign a Primary DNS server if required. (Optional)
13. Secondary DNS*: You can assign a Secondary DNS server if required. (Optional)
14. Connection Control: There are 3 options to start connection:
Auto Reconnect (Always-on): The device will always try to link to Internet.
Connect-on-demand: The device won’t try to connect to Internet until LAN PCs or
devices try to go to Internet. Once Internet connection is established, this
device will drop the connection if maximum idle time is reached.
Manually: The device won’t try to connect to Internet until users press “connect” button
at Status page. Once Internet connection is established, this device will drop
the connection if maximum idle time is reached.
15. Keep Alive: There are three options for keep alive feature as below.
Disable: Disable keep alive feature.
LCP Echo Request: The device will constantly send LCP packets for keeping alive.Enter the
time interval and the maximum failure count.
Ping Remote Host: Enter the Remote host IP address and the time interval to send the ping
packets for keeping alive.
16. NAT Disable: You can disable NAT feature if required.
Note. The items with * above are only available when choosing Manual for Dial-up Profile.