LevelOne WBR-6803 User manual

1
LevelOne
User Manual
Ver. 1.0
WBR-6803
150Mbps Wireless 3G Travel Router

2
Safety
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. The user could
lose the authority to operate this equipment if an unauthorized change or
modification is made.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
CE Declaration of conformity
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55022 class B for ITE, the essential protection requirement of
Council Directive 89/336/EEC on the approximation of the laws of the Member
States relating to electromagnetic compatibility.
CE Marking Warning
Hereby, Digital Data Communications, declares that this product is in compliance
with the essential requirements and other relevant provisions of Directive
1999/5/EC.
The CE-Declaration of Conformity can be downloaded at:
http://www.levelone.eu/support.php

3
General Public License
This product incorporates open source code into the software and therefore falls
under the guidelines governed by the General Public License (GPL) agreement.
Adhering to the GPL requirements, the open source code and open source
license for the source code are available for free download at
http://global.level1.com.
If you would like a copy of the GPL or other open source code in this software on a
physical CD medium, LevelOne (Digital Data Communications) offers to mail this
CD to you upon request, for a price of US$9.99 plus the cost of shipping.

4
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION ..................................................................................................5
1.1 PACKAGE LIST.................................................................................................5
1.2 HARDWARE INSTALLATION...........................................................................5
CHAPTER 2 GETTING STARTED WITH EASY SETUP UTILITY...........................................9
2.1 EASY SETUP BY WINDOWS UTILITY.............................................................9
2.2 EASY SETUP BY CONFIGURING WEB PAGES.......................................... 13
CHAPTER 3 MAKING CONFIGURATION............................................................................. 18
3.1 BASIC SETTING............................................................................................. 18
3.2 FORWARDING RULES.................................................................................. 34
3.2.1 VIRTUAL SERVER .................................................................................. 34
3.2.2 SPECIAL AP ............................................................................................ 36
3.2.3 MISCELLANEOUS................................................................................... 37
3.3 SECURITY SETTING...................................................................................... 38
3.4 ADVANCED SETTING ................................................................................... 39
3.5 TOOL BOX...................................................................................................... 53
CHAPTER 4 TROUBLESHOOTING ...................................................................................... 49
APPENDIX A. SPEC SUMMARY TABLE.............................................................................. 61
APPENDIX B. LICENSING INFORMATION .......................................................................... 62
Default Settings
IPAddress
192.168.1.1
Password
admin
Wireless Mode
Enable
Wireless SSID
LevelOne
Wireless Security
None

5
USB
Reset
WPS
RJ-45
ON/OFF
Power
Power LED
Battery lid
Wireless
3G USB
Ethernet
Chapter 1 Introduction
Congratulations on your purchase of this outstanding product: WBR-6803 WiFi Mobile Router.
This product is specifically designed for mobile user who needs to have the internet access
beyond his home and office. It provides a complete solution for Internet surfing and broadband
sharing. Instructions for installing and configuring this product can be found in this manual. Before
you install and use this product, please read this manual carefully for fully exploiting the functions
of this product.
1.1Package List
WBR-6803
Power Adapter
RJ-45 LAN Cable
Quick Installation Guide
CD Manual/QIG
Li-Ion Battery
1.2 Hardware Installation
A. Hardware configuration
LED Indicators
Power LED

6
B. LED indicators
Power LED indicator:
Power Source ON/OFF Switch LED Status Description
Battery Only
ON Green in flash Device ON, and Battery is in use.
ON Red Device ON, and Battery is low.
OFF N/A Device OFF
Power Adapter
ON Green Device ON, and Battery is fully
charged.
ON Amber
Device ON, and Battery is
charging, or no Battery installed.
OFF Amber Device OFF, and Battery is
charging.
OFF N/A Device OFF
Other LED indicator:
LED Status Description
Ethernet LED Green
RJ45 cable is plugged, and Ethernet connection
is established.
Green in flash Data access
USB LED
Green
3G/3.5G is on
Green in flash Data access
WiFi LED Green WLAN is on
Green in flash Data access
C. Installation Steps
Step 1. Install the battery:
Turn OFF the power switch, open the battery lid, and
then insert the Li-ion battery into the battery holder.
DO NOT insert or remove the Li-ion
battery while the power switch is at
ON position.
Step 2.
Close the battery lid

7
Step 3. Plug in power:
Connect with the power adapter to the receptor on the
back panel of it.
Step 4. Start to Charge the Battery:
Then plug the other end of the power adapter into a
wall outlet.
If it is the first time to put the battery
in, the power LED will show amber
which means the battery is been
charging. It will take about 3 hours
to fully charge the battery, and
when the battery is fully charged,
the power LED will show green.
Step 5. Power ON:
Turn ON the power switch.
Step 6. Connect with a USB 3G modem:
Plug your USB modem which is with activated SIM
card that is provided by your 3G service provider.
ON

8
Step 7. Connect with Ethernet Cable
Insert the Ethernet cable into RJ45 Ethernet Port on
the back panel. And then plug the other end of RJ45
into the computer or Laptop computer. The Ethernet
LED will show green color if the Ethernet connection is
normally connected.
Step 8. Start to configure
the device:
You can start to configure the
device via the Easy Setup
Utility.
(see Easy Setup Utility)

9
Chapter 2Getting Started with Easy Setup Utility
There are two approaches for you to set up the WiFi Mobile Router quickly and easily. One is
through executing the provided Windows Easy Setup Utility on your PC, and the other is through
browsing the device web pages and configuration.
2.1 Easy Setup by Windows Utility
Step 1：
Install the Easy Setup Utility
from the provided CD then
follow the steps to configure
the device.
Step 2
：
Select Language then click
“Next” to continue.
Step 3
：
Then click the “Wizard” to
continue.

10
Step 4：
Click “Next” to continue.
Step 5：
Select SSID, Chanel,
Security, and then click “Next”
to continue.

11
Step 6：
Enter SSID, Channel and
Security options, and then
click “Next” to continue.
Step 7：
Select 3G Service by clicking
3G icon to continue.

12
Step 8-1：
Select “Auto-Detection”, and
the Utility will try to detect and
configure the required 3G
service settings automatically.
Click “Next” to continue.
Step 8-2：
Or you can select “Manual”
and manually fill in the
required 3G service settings
provided by your ISP.
Click “Next” to continue.

13
Step 9：
The WiFi Mobile Router is
rebooted to make your entire
configuration take effect.
Step 10：
Setup is completed.
2.2 Easy Setup by Configuring Web Pages
You can also browse web UI to configure the device.
Browse to Activate the Setup Wizard
Type in the IP Address
(http://192.168.1.1)

14
Type in the default password
“admin” in the System
Password and then click
‘login’ button.
Select your language.
Select “Wizard” for basic
settings with simple way.
Press “Next” to start the Setup
Wizard.

15
Configure with the Setup Wizard
Step 1
:
Change System
Password.
Set up your system password.
(Default：admin)
Step 2: Select Time Zone
.
Step 3: Select Wan Type.
If you want to use 3G service
as the main internet access,
please set the WAN interface
as “Wireless WAN” and the
WAN type as “3G”.

16
Step 4: Set up 3G profile.
Select “Auto Detection”.
Step 5: Set up your Wireless
Network.
Set up your SSID.
Step 6: Set up Wireless
Security.
Set up your Authentication
and Encryption.

17
Step 7: Apply your Setting.
Then click Apply Setting.
Step 8:
Click Finish to complete it.

18
Chapter 3Making Configuration
Whenever you want to configure your network or this device, you can access the Configuration
Menu by opening the web-browser and typing in the IP Address of the device. The default IP
Address is: 192.168.1.1
Enter the default password “admin” in the System Password and then click ‘login’ button.
Then, you can browse the “Advanced” configuration pages for configuring this device.
3.1 Basic Setting

19
3.1.1. Network Setup
1. Ethernet port Configuration:
Off: Disable the Ethernet port.
LAN: The Ethernet port is as LAN port.
WAN: The Ethernet port is as LAN port.
Auto: It will be WAN Port if a DHCP server can be detected on the Ethernet port.
Otherwise, it will be LAN port.
2. LAN IP Address: The local IP address of this device. The computers on your network
must use the LAN IP address of this device as their Default Router. You can change it if
necessary.
3. Subnet Mask: Input your Subnet mask. (All devices in the network must have the same
subnet mask.) The default subnet mask is 255.255.255.0.
4. WAN Interface: Select Ethernet WAN or Wireless WAN to continue.
5. WAN Type: WAN connection type of your ISP. You can click WAN Type combo button
to choose a correct one from the following options:

20
A. 3G