LG Innotek TWFM-B006D User manual

User Manual
PRODUCT NAME : Dual Band 2T2R MIMO Wi-Fi Module
MODEL NAME : TWFM-B00 D
(00)-0073
The information contained herein is the exclusive property of LG Innotek
and shall not be distributed, reproduced or disclosed in whole or no in part
without prior written permission of LG Innotek.

User Manual
PAGE :
REG. DATE : 2012.07.25
MODEL NAME : TWFM-B00 D
REV. DATE : 2012.07.25
REV.NO : 1.0
©2012 LGIT. All righ s reserved.
1 / 8
Table of Contents
No. Descrip ion Page
1 Fea ures 2
2 Module Pho o 2
3 Block Diagram 3
4 S orage Condi ions 4
4 Opera ing Condi ions 4
5 Sof ware Programming 5
6 Pin Descrip ion 6
7 Ou line Drawing 7
8 Packing Informa ion 8

User Manual
PAGE :
REG. DATE : 2012.07.25
MODEL NAME : TWFM-B00 D
REV. DATE : 2012.07.25
REV.NO : 1.0
©2012 LGIT. All righ s reserved.
2 / 8
2. Module Photo
1. Features
TWFM-B006D is he small size and low power module for IEEE 802.11a/b/g/n wireless
LAN. TWFM-B006D is based on Broadcom BCM43236B solu ion.
IEEE 802.11 a/b/g/n Dual Band WLAN infras ruc ure
Size : 48mm x 30mm x 6.7mm
2.4GHz and 5GHz in ernal PA
Two s ream spa ial mul iplexing up o 300Mbps
Ex ernal ANT : EPA(Embedded and Press An enna)
Use on-chip OTP (One-Time Programmable)
USB 2.0
Suppor s drivers for Windows Vis a, 2000, XP, Linux
Securi y : WPA,WPA2,AES(TKIP) ,IEEE 802.1X
• Applica ion: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB

User Manual
PAGE :
REG. DATE : 2012.07.25
MODEL NAME : TWFM-B00 D
REV. DATE : 2012.07.25
REV.NO : 1.0
©2012 LGIT. All righ s reserved.
3 / 8
3. Block Diagram

User Manual
PAGE :
REG. DATE : 2012.07.25
MODEL NAME : TWFM-B00 D
REV. DATE : 2012.07.25
REV.NO : 1.0
©2012 LGIT. All righ s reserved.
4 / 8
Parameter Min Max Unit
S orage Tempera ure -10 +80 ℃
S orage Humidi y (@ 40℃)- 90 %
Caution : The specifica ions above he Table define levels a which permanen damage
o he device can occur. Func ion opera ion is no guaran eed under hese condi ions.
Opera ing a absolu e maximum condi ions for ex end periods can adversely affec he
long- erm reliabili y of he device.
• O her condi ions
1) Do no use or s ore modules in he corrosive a mosphere, especially where chloride
gas, sulfide gas, acid, alkali, sal or he like are con ained.
Also, avoid exposure o mois ure.
2) S ore he modules where he empera ure
and rela ive humidi y do no exceed 5 o 40℃and 20 o 60%.
3) Assemble he modules wi hin 6 mon hs.
Check he soldering abili y in case of 6 mon hs over.
4. Storage Conditions
Parameter Min Typ Max Unit
Opera ing Tempera ure 0 - +60 ℃
Opera ing Humidi y (40℃)- - 85 %
Supply Vol age 3.32 3.5 3.67 Vdc
5. Operating Conditions

User Manual
PAGE :
REG. DATE : 2012.07.25
MODEL NAME : TWFM-B00 D
REV. DATE : 2012.07.25
REV.NO : 1.0
©2012 LGIT. All righ s reserved.
5 / 8
The module is con rolled by wl command. I is in ended for hose evalua ing
and/or es ing Broadcom’s IC, describes a subse of he commands available in wl,
he Broadcom ® WLAN clien u ili y.
The syn ax is as follows:
wl <adap er> [-h] [-d|u|x] <command> [argumen s]
where
-h his message and command descrip ions
-d ou pu forma signed in eger
-u ou pu forma unsigned in eger
-x ou pu forma hex decimal
The [h,u] op ion is only o prin help.
O her syn ax specifics are as follows:
• En ries wi hin square bracke s, such as [argumen s], are op ional.
In he above example,
swi ches wi hin bracke s, such as –h, are yped as shown. The |symbol should no be
yped, i represen s he word or.
• En ries wi hin angle bracke s, such as <adap er>, are required and indica e ha
a value mus be inser ed in place of he i em con ained wi hin he angle bracke s.
• En ries shown ou side of ei her square or angle bracke s are o be yped as shown.
• CMDS
Syn ax: wl cmds
Purpose: Genera es a lis of available commands.
Parame ers:None
Re urns: All commands available o he a ached 43XX chip.
• VER
Syn ax: wl ver
Purpose: Genera es a lis of available commands.
Parame ers:None
Re urns: All commands available o he a ached 43XX chip.
•Please refer to ‘80211-TI201-R’ technical document of Broadcom to other commands.
. Software Programming
-1. Command syntax
-2. Command List and Version

User Manual
PAGE :
REG. DATE : 2012.07.25
MODEL NAME : TWFM-B00 D
REV. DATE : 2012.07.25
REV.NO : 1.0
©2012 LGIT. All righ s reserved.
6 / 8
7. Pin Description
Pin No. Pin Name I/O Pin Description
1 VCC I VDD 3.5V
2 D- I/O USB Communica ion signal USB_DN
3 D+ I/O USB Communica ion signal USB_DP
4 GND - GND
5 WOW I Wake On WLAN
6 NC I NC
< TOP View >
Note.
1) Recommend a Module ins all sequence for preven USB device failure
- Supply 3.5V power
- Connec o da a signal (USB_DP, USB_DN)
2) If remove he module, proceed in reveres sequence
3) Connec or : (CONN 12507WR-06L, YEONHO ELECTRONICS CO., LTD.)
A
A

User Manual
PAGE :
REG. DATE : 2012.07.25
MODEL NAME : TWFM-B00 D
REV. DATE : 2012.07.25
REV.NO : 1.0
©2012 LGIT. All righ s reserved.
7 / 8
8. Outline Drawing

User Manual
PAGE :
REG. DATE : 2012.07.25
MODEL NAME : TWFM-B00 D
REV. DATE : 2012.07.25
REV.NO : 1.0
©2012 LGIT. All righ s reserved.
8 / 8
9. Packing Information
• 1Tray Package Q’ y : 120EA
• Tray Ma erial : an is a ic PET
• 1Tray Weigh : 0.2kg
(1 Module Weigh : 6.8 ±0.7g)
• 1Box Package Q’ y : 720EA
• Box Size : A x B x C (512 x 377 x 121.5)
• Box Ma erial : Corruga ed Fibreboards
• 1Box Packing Weigh : 6.6 ±0.7kg
• Tray S acking Q’ y :6EA
Corruga ed Fibreboard
Tray
Inner Box
• To al Packing Q’ y : 1,440EA
• To al Packing Weigh : 13.2 ±1.5kg
PP Band
Barcode LabelRoHS Marking
• RoHS Marking :
Label, S amp, Prin ing
• Marking Color :
Gray or Red for S amp, Label,
Prin ing on he board and e c.
Black only for Prin ing on Label.

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could
void your authority to operate this equipment.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum 20 cm
between the radiator and your body.
Remark
■This radio can not be installed in host where co-located or operating in conjunction
with any other antenna or transmitter.
■This radio must be restricted to install in host that is intended for indoor use only for
5150-5250 MHZ band.
■Wi-Fi label is written at the end of the TV.
For label requirement when transmitter module is installed in a host, the host shall have an additional
permanent label referring to the enclosed module.
“Contains Transmitter Module FCC ID: BEJTWFMB006D