LG Innotek LGD323 User manual

User Manual
2CH Front HD / Rear HD High Resolution
Front 30FPS / Rear 30FPS
Format free recording
Low battery and high temperature shutdown
Audio prompts
LGD323

Non LCD HD-HD DASHCAM
Do not operate the product while driving. It may cause an accident.
The product must be installed at a point which would not obstruct the driver’s view.
Do not allow unauthorized disassembly or alteration to the product. It may cause
malfunction, and the consequent product damage will not be covered under the
warranty.
If the product is damaged or power is cut off by a serious accident, the product may
not be able to record such event.
Always keep the windshield clean to enable clear recording.
Since the product’s purpose is to record video data during driving, video quality may be
deteriorated when in/out the tunnel, and at night or by contrast and backlight.
Contaminated camera lens may deteriorate the video quality. Keep the lens clean.
Do not place the product under direct sunlight or inside the closed vehicle as it may
cause malfunction.
Do not use chemicals or detergent to clean the product. Clean gently with soft cloth.
Use of the product at temperature below -20℃ or above 70℃ may cause malfunction
or breakdown. (This caution should be applied when product is unused.)
Do not use the product in places in high temperature/humidity.
Do not exert excessive force to the product (especially to buttons and to bracket) as it
may cause breakdown.
Check for correct recording, before each use.
Extended exposure to sunlight and high temperature in the summer may cause
malfunction.
Do not turn off power, or remove the MicroSD card during firmware upgrading as it
may cause malfunction.
Do not touch the cigarette lighter cable with wet hands as it may cause electric shock.
Do not use a damaged cigarette lighter cable as it may cause electric shock or fire.
Do not plug the cigarette lighter cable in near heating devices.
Do not leave the product connected to the cigarette lighter if not in use for a long
period of time. Remove the cable from the product.
Insert the cigarette lighter plug securely.
Do not bend or pull the cigarette lighter cable by excessive force, or place heavy
objects on the cable.
(It may damage the cord and as a result it may cause electric shock or fire.)
The recorded file could be deleted to make an available space for recording even if
the overwriting setting is off
Caution on Operation and Storage
For safety and prevention of any property damage, be sure that user use the product
after reading the following(Operation and Caution) carefully.
1Caution for Safety

Non LCD HD-HD DASHCAM
For safety and prevention of any property damage, be sure that you use the produc
t after reading the following (Caution on SD Card) carefully.
Caution on SD Card
1Caution for Safety
In order to confirm normal operation of the product, please check the image of
the MicroSD card and format it on a regular basis. (PC format needed one to
two times per month.)
Because the MicroSD card is a consumable, if it is used for a long time, you may
lose the data or may not record due to an error, so please check it periodically.
When the product is recording or the power is on, do not eject the MicroSD
card, as it may cause a failure of the MicroSD card and data loss.
If temperature gets too high in the vehicle, data storing may be disabled, or
data may be damaged. Park your vehicle in the shade in the summer.
When validating an accident or car damage, please remove the MicroSD
card and keep separate. Due to overwrite, important data may be deleted.
When turning off the power of the product and remove the MicroSD card before
LED is turned off, the last recording file may not be saved, so please be careful.
When driving a car, do not remove the MicroSD card. Make sure to remove it
safely when a car is in parking or stop.
After turning on the power, make sure that it is in normal operation.
Please note that the warranty period of the MicroSD card is three (3) months,
and recommend to replace it every (6) months. Please purchase and use
a MicroSD card that meets the manufacturers recommended specification.
The MicroSD card randomly purchased other than the one we provide, shall
be excluded from the warranty, and we shall not take any responsibility for loss
and damage of the data recorded in the MicroSD card in any case.

Non LCD HD-HD DASHCAM
In the parking mode, if the voltage stays below the power cut-off limit for longer than 30
seconds, this product will be automatically turned off to protect batteries of the vehicle.
If you start a car again, the product will start operating normally.
If the temperature inside the vehicle rises during the parking mode, the product will be automatically turned
off to protect itself.
If you do not want the automatic temperature cut-off function, set the temperature cut-off function to 'No'
. If you start a car again, the product will start operating normally.
Item Specifications
CPU ARM Cortex-A7 CPU
Flash Memory 1Gb
RAM 2Gb
Video Recording 2 channels
Camera Front: 1M pixels / Rear: 1M pixels
Recording Resolution
Front : HD (1280 x 720P)
Rear : HD (1280 x 720P)
Memory Device micro SD Card (up to 128GB opt)
View Angle Front : 91.8°(H) X 66.8°(V) X 128.5°(D) : IMX225
Rear : 89.9°(H) X 64.9°(V) X 120.3°(D) :HDX10
GPS External GPS (optional)
Input Power DC 12V~24V
Power Consumption Up to 350 mA@13V
Auxiliary Power Super Capacitor
G-Sensor Triaxial accelerometer G sensor
Video Format AVI
Audio Recording Internal high sensitivity microphone
Audio Guide Internal speaker
Video Codec H.264 / AVC
Audio Codec PCM S16 LE
High Temperature
Cut-off Function Yes
Constant Power Cut
-off
Function Turned off, 11.4V(23.1), 11.6V(23.4), 11.8V(23.7), 12.0V(24.0), 12.2V(24.3)
Operating Temperature -20℃ ~ +70℃
Storage Temperature -30℃ ~ +80℃
2Product Specifications

Non LCD HD-HD DASHCAM
These are the accessories included with the product at the time of purchase.
Bracket
Clip
Main Body(LGD323)
[Consumable]
MicroSD Card & Adapter
Cigarette Lighter Adapter
Power Cord (CLA)
Rear(HD) Camera,
Rear Camera Video Cable
Quick Manual
GPS ModuleHardwire Cable
Manual
3Package
※ According to the product types, CLA, Hardwire Cable or GPS Module Could be included Or
Option Product.
※ The above image may look different from the actual components .
The components of the product mentioned in this Quick Manual are subject to
change without prior notice to improve its performance.

Non LCD HD-HD DASHCAM
Connect the ( ㅡ) shape’s rear camera cable
to a rear camera connection and the ( ㄱ)
shape’s one to the body.
※ Note ※
Please note that the product will not recordif
the cable is connected incorrectly.
4. Connect the Rear Camera Cable
1. Shutdown a car battery and power
▶Rear Camera Installation
2. Attach the Rear Camera.
5. Check an Operation
Please power off the car and ignition
before installation.
(Disconnect the power connection)
Remove the protective tape and attach
the rear camera in proper location in
windshield.
Turn the body on and checka proper
operation by playing the recording files
on the MicroSD card or TV-OUT.
(The video splitter cable has to be
connected when checking TV-OUT.).
After checking recording operation,
well-arrange the cable.
If you embed cable to car wall, please check
cable connection. Also after embedded
double-check if the product can record
properly..
3. Adjust the Rear Camera Angle
6. Arrange the Front/Rear Camera Cable
Adjust the angle with the rear camera
attached.
1. Insert the MicroSD card in the card
slot. (Check the MicroSD card direction)
6. Connect the CLA
to the 12V power
socket.
2. Remove the protective tape from
the bracket.
4. Attach the product in place on
the top of front windshield or
middle, left or right of the mirror.
Adjust up front one level.
3. Connect the cigarette lighter cable
to power connection..
▶Front Camera Installation
5Product Installation
5. Adjust the front camera angle
while attaching the product.
It is recommended that the
adjustment angle be centered
on the horizon.
7. Arrange the power
cable

Non LCD HD-HD DASHCAM
▶How to remove the bracket
Power
Connection
Rear Camera
Connection
GPS
Connection
SD Card Slot
4Product Parts
Power Button
GPS LED
REC LED Mic/Speaker
Front Camera

Non LCD HD-HD DASHCAM
▶Title of Recorded Video Files
6Recorded Video
Title of
recorded file aaab_cccc_dddddd_eeeeee_f.avi
aaa Type of
recording Description Remarks
inf Normal recording inf0_0000_140120_091603_I.avi
evt Impact recording evt0_0000_140120_091603_I. avi
moe Motion recording moe0_0000_140120_091603_P
b channel Description Remarks
0 1 channel Front
1 2 channels Front+rear
cccc index Description Remarks
0000~9999 File order The index starts with 0. The last file index varies
depending on the size of SD card memory.
dddddd
Year, month, and
date created Description Remarks
YYMMDD 140120
eeeeee Time created Description Remarks
hhmmdd 091603
f Recording mode Description Remarks
I Normal recording Turned on when ACC is on
P Parking recording Turned on when ACC is off
▶Properties of Recorded Video
Bitrate (bits per second)
Definition HD Video HD Video
Ultra-high definition 6 Mbps 6 Mbps
High definition 5 Mbps 5 Mbps
Standard definition 4 Mbps 4 Mbps
1ch Recording (bps) 2ch Recording (bps)
Normal Parking Normal Parking
Front Rear Front Rear
Ultra-high
definition 6 6 6 6 6 6
High definition 5 5 5 5 5 5
Standard
definition 4 4 4 4 4 4
FPS (Frame per second)
1ch Recording (FPS) 2ch Recording (FPS)
Normal Parking
Normal Parking
Front Rear Front Rear
Ultra-high
definition 30 30 30 30 30 30

Non LCD HD-HD DASHCAM
7Recorded File
Each recorded file will be saved using the format-free system based on file size.
Normal : 120 MByte
Event : 60 MByte
Motion : 60 Mbyte
▶Size of Recorded File
▶Recording Time by SD Card Size
(Unit: Minute)
Chan
nel
Definition Camera
16GB 32GB 64GB
Normal
(50%)
Motion
(20%)
Event
(30%)
Normal
(50%)
Motion
(20%)
Event
(30%)
Normal
(50%)
Motion
(20%)
Event
(30%)
1
Chan
nel
Ultra-
high
definition
Front 171 35 53 347 72 108 699 145 217
High
definition
Front 205 35 53 416 72 108 838 145 217
Standard
definition
Front 256 35 53 520 72 108 1048 145 217
2
Chan
nels
Ultra-
high
definition
Front/Rear
85 34 51 173 69 104 349 140 210
High
definition
Front/Rear
102 35 53 208 72 108 419 145 217
Standard
definition
Front/Rear
128 35 53 260 72 108 524 145 217
By time : When the memory capacity runs out, recorded files will be automatically deleted beginning with
the oldest one.
By type : The percentage of allowed memory usage is set per recording type. When the memory capacity
for a recording type runs out, recorded files of the recording type will be automatically deleted
beginning with the oldest one. Recordings of an accident can also be deleted.
HD + HD
▶On-Screen Display (OSD) Description
(1) Model name : LG INNOTEK LGD323
(2) F/W Version : V :1.1.053
(3) Date recorded : 2016/11/28 MON 10:07:51
(4) G-Sensor Value : X :-0.2 Y :-0.0 Z :-0.9
(5) Speed (Displayed only when GPS is connected) :
(6) Voltage : Input voltage
(7) INDEX (aaaabbbbcccc)
①aaaa : Normal file index
②bbbb : Event file index
③cccc : Motion file index

Non LCD HD-HD DASHCAM
10
8Recording Scenario
①Recording of an impact event in the driving mode
A buffer video of 10 seconds will be included in the video when an impact event occurs in the driving mode.
If the power supply is cut off immediately after an impact event while driving, the event recording at the end may
not be performed normally. In this case, you can refer to the normal recording of the same timeline.
②Recording of multiple impact events in the driving mode
If another event occurs during impact event recording, the second event can be processed 10 seconds after
occurrence of the first impact event.
After the first impact event file is saved, the second one is saved.
If the second impact event happens after or at the same time with the completion of the first impact event, the
recording of the second impact event will start 10 seconds before the completion of the first impact event.
Once an event happens and a new file is created, the second event will not be recognized for 10 seconds after
occurrence of the first event.
▶Driving Mode
This refers to the recording while the vehicle is parked with ACC off.
Motion event is not recognized within 10 seconds after switching to the parking mode. The product can sense a
motion 10 seconds later.
▶Parking Mode
①Recording of an impact event in the parking mode
A buffer video of 10 seconds will be included in the video when an impact event occurs in the parking mode.
②Recording of multiple impact events in the parking mode
If another event occurs during impact event recording, the second event can be processed 10 seconds after
occurrence of the first impact event. After the first impact event file is saved, the second one is saved.
If the second impact event happens after or at the same time with the completion of the first impact event,
the recording of the second impact event will start 10 seconds before the completion of the first impact event.
Once an event happens and a new file is created, the second event will not be recognized for 10 seconds after
occurrence of the first event.
③Recording of a motion event in the parking mode
A buffer video of 10 seconds will be included in the video when a motion event occurs in the parking mode.
④Recording of multiple motion events in the parking mode
If another motion event occurs during motion event recording, the second event can be processed 10 seconds
after occurrence of the first motion event. After the first motion event file is saved, the second one is saved.
If the second motion event happens after or at the same time with the completion of the first motion event,
the recording of the second motion event will start 10 seconds before the completion of the first motion
event.
⑤Recording overlap of a motion event and an impact event in the parking mode
If an impact event occurs together with a motion event, recording of both events will overlap during the
parking mode.
A buffer video of 10 seconds will be included in the impact event video when an impact event occurs during
motion recording. (This is the same even when a motion event occurs during impact recording.)
If another event occurs during the overlap of an impact event and a motion event, the product follows the
scenario for recording of multiple events for the corresponding event type.
▶Switching the Mode
①Driving mode > Parking mode
Automatic switching: If ACC is cut off in the normal recording mode, the product enters the parking mode
10 seconds later.
②Parking mode > Driving mode
Automatic switching: If ACC power is high, the product automatically switches to the driving mode.

Non LCD HD-HD DASHCAM
Low Voltage Cut-off
11
LED Operation
▶Front Security LED and User Notice LED
Item
Status GPS
(Blue) Remark
2 Channel 1 Channel
Green Red
Booting Blink alternately
Recording
SC card not
inserted OFF
Normal Green ON Red 3 seconds /Green
1 second
Event Green/ Red blink (1 sec.) Normal Parking
Motion Green/ Red blink (500 msec.) Parking Motion
Parking Blink alternately Not recorded
Not installed OFF
Not Fixed Blinks (1 sec.)
Fixed ON
Front Security LED operates only when the language is set to Korean or Chinese (refer to the table above).
If the language is set to others (Japanese, English, Spanish, and French), the Security LED is turned off.
If you change the LED settings through WLAN or PC Viewer, the changed settings apply.
Note 1) If you select "1 Channel" in the settings when 2 channels are connected, the product follows the scenario
for 2-channel connection.
▶Power Management
11
You can set the constant power cut-off voltage to Disable (11V) or 11.4 - 12.2 (23.1 - 24.3) V on the Viewer.
If an event occurs (and the event file is saved) with the voltage remaining below the cut-off limit and if the
voltage does not rise above the cut-off limit for 30 seconds or more, this product is turned off.
The constant power cut-off function is not enabled in the driving mode. It is enabled only in the parking mode.
▶Display on the Viewer
The Viewer displays as follows:
Disable is set to 11.0 (23.0) V.
0 Disable
1 11.4(23.1)V
2 11.6(23.4)V
3 11.8(23.8)V
4 12.0(24.0)V
5 12.2(24.3)V
Channel Switching Scenario
10
9
▶Scenario for Switching between 1-Channel and 2-Channel
Automatic Recording
If the rear camera is removed when the product is set to 2 channels, the 2-channel recording
continues and the rear screen shows black frames.
The rear connection alarm sounds once and repeats every 10 seconds. This can be stopped by
changing the rear connection or the channel settings.
At this time, the recording may be stopped for 1 - 3 seconds.

Non LCD HD-HD DASHCAM
Using Multi-Key
12 High Temperature Cut-off
The temperature cut-off function is used to protect the product from high temperature.
The high temperature cut-off function is not enabled in the normal mode.
The temperature cut-off function is enabled only if the "Use temperature cut-off" option is set to "Yes" in the
black box viewer.
If the product stops operation due to high temperature, recording stops and the product turns off.
The cut-off temperature is based on the temperature outside the product (inside the vehicle) and is 76±5℃.
The temperature detected by the internal temperature sensor is 110℃. (Room temperature 71 - 75℃)
If the temperature cut-off function is activated, recording and motion detection stop, and the front/rear LEDs
turn off with a voice message "Turning off".
▶G Sensor Operation
Based on events while driving (5: most sensitive, 1: least sensitive)
Viewer OFF 5 4 3 2 1
Gravity 4.0 1.1 0.9 0.7 0.5 0.3
Based on events when parked (5: most sensitive, 1: least sensitive)
Viewer OFF 5 4 3 2 1
Gravity 12.0 0.35 0.28 0.22 0.17 0.13
▶Motion Event Activation
You can set the sensitivity of a motion event activation.
If you set the sensitivity too high, a motion event is activated by very small changes, creating too many
motion events.
Stage 0 1 2 3 4 5
Sensitivity OFF Very
Sensitive Sensitive Normal Insensiti ve
Very
Insensitive
14
▶Resetting the Product
Press and hold the multi-key button for 5 seconds until the product rings three times. If you release the
button when it rings two times, the product repeats ringing three times for 20 seconds. If you press the
multi-key button once again within 20 seconds, the product is reset with a message "Turning off". If you
do not press the button again within 20 seconds, the product rings once differently and the reset is
cancelled.
▶Changing the Language
If you press and hold the multi-key button for 7 seconds or more, you can hear a voice message changing
according to different languages. Release the button when you hear the language you want. Then, the
language changes to the one you want.
The language switches in the order of English > French > Japanese > Chinese > Korean.
▶Microphone On/Off
If you press and hold the multi-key button for 3 seconds, the product rings once. If you release the button
when it rings, the microphone turns on with a message "The microphone is turned on". If you repeat the
above procedure, the microphone turns off with a message "The microphone is turned off".
Sensor Operation
13

Non LCD HD-HD DASHCAM
To insert or remove a SD card to and from the product, you need to turn off the product first.
▶Automatic Formatting
Update is performed only when you insert a SD card with the update firmware and restart the product by turning it
off/on.
When booting, if the SD card has an unsupported file system, a voice message is heard asking whether to format the
card. If you want to format the card, press the multi-key button once.
Even if the SD card contains the setup.cfg file, if the card is not formatted in the black box (if it is formatted in the
PC), the black box asks whether to format the card.
▶Manual Formatting
To manually format the SD card, turn on the product while pressing and holding the multi-key button. Press and
hold the button until booting is completed.
When you hear a voice message asking whether to format the card, release the multi-key button. Then press the
button once again to format the card. To exit the format mode without formatting the card, turn off the power
switch.
15 SD Card
▶Setting the Time Zone (GPS connected)
You can change the time zone in the Time Zone option under System Settings of your smartphone app. The
changed time zone is a time zone relative to GMT/UTC and is applied when the GPS is connected.
▶Setting the Current Time (GPS not connected)
If you connect the product to your smartphone, the smartphone time is applied as the time of the black box.
In the Viewer, change the time under the Default Settings menu and change "Apply Time Settings" to "Yes". Insert
the SD card with the saved settings to the black box and boot it to set the time of the black box. When you set the
time using the Viewer, you must consider the time needed to insert the SD card and boot the black box.
Using Multi-Key
Time Settings
16

Non LCD HD-HD DASHCAM
17 Using the PC Windows Viewer
▶Screen Organization
<Windows PC Viewer>
- LG Innotek recommends above
Windows7(32/64bit)/Intel core i3/RAM 2GB/Display 1920x1080
8
2 3 4 5 6 7
10
1
9
28
13 14 15 16 17 18 19 20 21 22
23 24 25 26 27
11
12
Item Description Item Description
1Front channel/Front&rear channels 15 Play the previous file
2Viewer settings
16 Move 5 seconds backward
3Black box settings 17 Play or pause
4Print the video 18 Stop
5Capture the video 19 Move 5 seconds forward
6Zoom 20 Play the next file
7Separate the files 21 Adjust voice volume
8
Switch between the video list and the map
screen
22 Total file duration/play time
9Find file location
23 Brightness/Saturation
10 Screenfor switching between the video
list and the map screen 24 GPS signal strength
11 Play bar 25 Driving speed
12 Switchto full screen 26 Latitude/Longitude
13 Flip horizontally 27 G sensor information
14 Flip vertically 28 Play screen

Non LCD HD-HD DASHCAM
Item Description
JPEG Storage Path Set the storage path of captured screen image files.
Select Language Select user language.
Play Mode Set the number of channels.
Repeated Play Set whether to play the video repeatedly.
Always at the Top Set whether to display the viewer window always at the top.
Flip Video Set the vertical/horizontal flip of a video.
Product Model Select the product model.
Video Adjustment Show the brightness/contrast/saturation of the Viewer play screen.
Volume Show the video volume of the Viewer play screen.
▶Viewer Settings
15
- In the PC viewer (or Mac viewer), the language setting of the viewer setup is a menu to change the languag
e of the viewer
The language setting of the Dashcam configuration is the menu for changing the language of Dashcam.
- In PC Viewer, set the Product model to LGD323 in Viewer setup.
(Mac Viewer automatically imports model information from SD card)
17 Using the PC Windows Viewer

Non LCD HD-HD DASHCAM
Item Description
Mode setting Set the recording mode.
Front Video quality Set the definition of the front recording video.
Rear Video quality Set the definition of the rear recording video.
Motion Sensitivity Set the motion detection sensitivity in the parking mode.
Driving Mode G-Sensor Set the G-Sensor event sensitivity in the driving mode.
Parking Mode G-
Sensor
Set the G-Sensor event sensitivity in the parking mode.
Voice Volume Set the guide voice volume.
Recording Volume Set the voice recording volume.
OSD Output Set the OSD output for video.
Speed Unit Set the speed unit.
Language settings Set the guide voice language..
Cut-off Voltage Set the cut-off voltage when using the constant power.
Recording Channel Set the recording channels.
Apply Time Settings
Apply the time changed in the Time Settings option. (You must select Yes to apply the
changed time.)
Time configuration Set the time of the recorded file.
High temp shutdown Set the High temp. shutdown.
16
▶Settings 1
17 Using the PC Windows Viewer

Non LCD HD-HD DASHCAM
Item Description
Camera
Sensor Set the brightness, contrast, and saturation. Press the Reset button to reset the
sensor to the default settings.
SD Card
Percentage
setting Set the storage percentage for each recording file type.
Standard time
Zone If GPS is used, it automatically synchronizes with the time zone for the region.
Daylight
Saving Time
Set whether to apply the daylight saving time.
17
▶Settings 2
17 Using the PC Windows Viewer

Non LCD HD-HD DASHCAM
▶Screen Organization
< MAC PC Viewer>
- LG Innotek recommends above OSX : 10.11.x (OS X El Capitan)
6
2 2 3 4 5
8
1
7
26
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25
9
10
Item Description Item Description
1Front channel/Front&rear channels
15 Play or pause
2Viewer settings
16 Stop
3Black box settings 17 Move 5 seconds forward
4Print the video 18 Play the next file
5Capture the video 19 Adjust voicevolume
6
Switch between the video list and the map
screen
20 Total file duration/play time
7Find file location 21 Brightness/Saturation
8Screenfor switchingbetween the video
list and the map screen
22 GPS signal strength
9Play bar 23 Driving speed
10 Switchto full screen 24 Latitude/Longitude
11 Flip horizontally 25 G sensor information
12 Flip vertically 26 Play screen
13 Play the previous file
14 Move 5 seconds backward
18 Using the PC Mac Viewer

Non LCD HD-HD DASHCAM
Item Description
Path of saving Set the storage path of captured screen image files.
Language selection Select user language.
Playback Mode Set the number of channels.
Always at the Top Set whether to display the viewer window always at the top.
Reverse video Set the vertical/horizontal flip of a video.
Color Show the brightness/contrast/saturation of the Viewer play screen.
▶Viewer setup
19
- In the PC viewer (or Mac viewer), the language setting of the viewer setup is a menu to change the languag
e of the viewer
The language setting of the Dashcam configuration is the menu for changing the language of Dashcam.
- Mac Viewer automatically imports model information from SD card.
18 Using the PC Mac Viewer

Non LCD HD-HD DASHCAM
Item Description
Mode setting Set the recording mode.
Front Video quality Set the definition of the front recording video.
Rear Video quality Set the definition of the rear recording video.
Motion
detec. s
ensitivity
Set the motion detection sensitivity in the parking mode.
Driving Mode G-Sensor Set the G-Sensor event sensitivity in the driving mode.
Parking Mode G-
Sensor
Set the G-Sensor event sensitivity in the parking mode.
Audio guide Volume Set the guide voice volume.
Recording Volume Set the voice recording volume.
OSD Output Set the OSD output for video.
Speed Unit Set the speed unit.
Cut-off Voltage setting Set the cut-off voltage when using the constant power.
Recording Channel Set the recording channels.
Apply Time conf.
Apply the time changed in the Time Settings option. (You must select Yes to apply the
changed time.)
Time configuration Set the time of the recorded file.
Language selection Set the guide voice language..
High temp shutdown Set the High temp. shutdown.
20
18 Using the PC Mac Viewer
▶Basic settings