LG Innotek LGD521 User manual

User Manual
2CH Front Full HD / Rear HD High Resolution
Front 30FPS / Rear 30FPS
Format free recording
Low battery and high temperature shutdown
Security LED & Audio prompts
Wireless Connectivity
LGD521
All manuals and user guides at all-guides.com
all-guides.com

Non LCD FHD-HD DASHCAM
Do not operate the product while driving. It may cause an accident.
The product must be installed at a point which would not obstruct the driver’s view.
Do not allow unauthorized disassembly or alteration to the product. It may cause
malfunction, and the consequent product damage will not be covered under the
warranty.
If the product is damaged or power is cut off by a serious accident, the product may
not be able to record such event.
Always keep the windshield clean to enable clear recording.
Since the product’s purpose is to record video data during driving, video quality may be
deteriorated when in/out the tunnel, and at night or by contrast and backlight.
Contaminated camera lens may deteriorate the video quality. Keep the lens clean.
Do not place the product under direct sunlight or inside the closed vehicle as it may
cause malfunction.
Do not use chemicals or detergent to clean the product. Clean gently with soft cloth.
Use of the product at temperature below -20℃ or above 70℃ may cause malfunction
or breakdown. (This caution should be applied when product is unused.)
Do not use the product in places in high temperature/humidity.
Do not exert excessive force to the product (especially to buttons and to bracket) as it
may cause breakdown.
Check for correct recording, before each use.
Extended exposure to sunlight and high temperature in the summer may cause
malfunction.
Do not turn off power, or remove the MicroSD card during firmware upgrading as it
may cause malfunction.
Do not touch the cigarette lighter cable with wet hands as it may cause electric shock.
Do not use a damaged cigarette lighter cable as it may cause electric shock or fire.
Do not plug the cigarette lighter cable in near heating devices.
Do not leave the product connected to the cigarette lighter if not in use for a long
period of time. Remove the cable from the product.
Insert the cigarette lighter plug securely.
Do not bend or pull the cigarette lighter cable by excessive force, or place heavy
objects on the cable.
(It may damage the cord and as a result it may cause electric shock or fire.)
The recorded file could be deleted to make an available space for recording even if
the overwriting setting is off
Caution on Operation and Storage
For safety and prevention of any property damage, be sure that user use the product
after reading the following(Operation and Caution) carefully.
1Caution for Safety
2
All manuals and user guides at all-guides.com

Non LCD FHD-HD DASHCAM
For safety and prevention of any property damage, be sure that you use the produc
t after reading the following (Caution on SD Card) carefully.
Caution on SD Card
1Caution for Safety
In order to confirm normal operation of the product, please check the image of
the MicroSD card and format it on a regular basis. (PC format needed one to
two times per month.)
Because the MicroSD card is a consumable, if it is used for a long time, you may
lose the data or may not record due to an error, so please check it periodically.
When the product is recording or the power is on, do not eject the MicroSD
card, as it may cause a failure of the MicroSD card and data loss.
If temperature gets too high in the vehicle, data storing may be disabled, or
data may be damaged. Park your vehicle in the shade in the summer.
When validating an accident or car damage, please remove the MicroSD
card and keep separate. Due to overwrite, important data may be deleted.
When turning off the power of the product and remove the MicroSD card before
LED is turned off, the last recording file may not be saved, so please be careful.
When driving a car, do not remove the MicroSD card. Make sure to remove it
safely when a car is in parking or stop.
After turning on the power, make sure that it is in normal operation.
Please note that the warranty period of the MicroSD card is three (3) months,
and recommend to replace it every (6) months. Please purchase and use
a MicroSD card that meets the manufacturers recommended specification.
The MicroSD card randomly purchased other than the one we provide, shall
be excluded from the warranty, and we shall not take any responsibility for loss
and damage of the data recorded in the MicroSD card in any case.
3
All manuals and user guides at all-guides.com

Non LCD FHD-HD DASHCAM
In the parking mode, if the voltage stays below the power cut-off limit for longer than 30
seconds, this product will be automatically turned off to protect batteries of the vehicle.
If you start a car again, the product will start operating normally.
If the temperature inside the vehicle rises during the parking mode, the product will be automatically turned
off to protect itself.
If you do not want the automatic temperature cut-off function, set the temperature cut-off function to 'No'
. If you start a car again, the product will start operating normally.
Item Specifications
CPU ARM Cortex-A7 CPU
Flash Memory 1Gb
RAM 2Gb
Video Recording 2 channels
Camera Front: 4M pixels / Rear: 1M pixels
Recording
Resolution
Front : FHD (1920 x 1080P)
Rear : HD (1280 x 720P)
Memory Device micro SD Card (up to 128GB opt)
View Angle Front : 110°(H) X 60°(V) X 130°(D) : OV4689
Rear : 89.9°(H) X 64.9°(V) X 120.3°(D) : HDX10
GPS External GPS (optional)
Input Power DC 12V~24V
Power Consumption Up to 350 mA@13V
Auxiliary Power Super Capacitor
G-Sensor Triaxial accelerometer G sensor
Video Format AVI
Audio Recording Internal high sensitivity microphone
Audio Guide Internal speaker
Video Codec H.264 / AVC
Audio Codec PCM S16 LE
High Temperature
Cut-off Function Yes
Constant Power Cut-
off Function Turned off, 11.4V(23.1), 11.6V(23.4), 11.8V(23.7), 12.0V(24.0), 12.2V(24.3)
Operating Temperature -20℃ ~ +70℃
Storage Temperature -30℃ ~ +80℃
2Product Specifications
4
All manuals and user guides at all-guides.com

Non LCD FHD-HD DASHCAM
These are the accessories included with the product at the time of purchase.
The above image may look different from the actual components .
The components of the product mentioned in this Quick Manual are subject to
change without prior notice to improve its performance.
Bracket
Clip
Main Body(LGD521)
[Consumable]
MicroSD Card & Adapter
Cigarette Lighter Adapter
Power Cord (CLA)
Rear(HD) Camera,
Rear Camera Video Cable
Quick Manual
GPS Module
[Option]]
Hardwire Cable
[Option]
Manual
3Package
5
All manuals and user guides at all-guides.com

Non LCD FHD-HD DASHCAM
Front Camera
▶How to remove the bracket
Security LED
WLAN Button(Multi Key)
Power Button
GPS LED
REC LED Mic/Speaker
Power
Connection
Rear Camera
Connection
GPS
Connection
SD Card Slot
4Product Parts
6
All manuals and user guides at all-guides.com
all-guides.com

Non LCD FHD-HD DASHCAM
Connect the ( ㅡ) shape’s rear camera cable
to a rear camera connection and the ( ㄱ)
shape’s one to the body.
※ Note ※
Please note that the product will not record if
the cable is connected incorrectly.
4. Connect the Rear Camera Cable
1. Shutdown a car battery and power
▶Rear Camera Installation
2. Attach the Rear Camera.
5. Check an Operation
Please power off the car and ignition
before installation.
(Disconnect the power connection)
Remove the protective tape and attach
the rear camera in proper location in
windshield.
Turn the body on and check a proper
operation by playing the recording files
on the MicroSD card or TV-OUT.
(The video splitter cable has to be
connected when checking TV-OUT.).
After checking recording operation,
well-arrange the cable.
If you embed cable to car wall, please check
cable connection. Also after embedded
double-check if the product can record
properly..
3. Adjust the Rear Camera Angle
6. Arrange the Front/Rear Camera Cable
Adjust the angle with the rear camera
attached.
1. Insert the MicroSD card in the card
slot. (Check the MicroSD card direction)
6. Arrange the power cable
2. Remove the protective tape from
the bracket.
4. Attach the product in place on the t
op of front windshield or middle, left
or right of the mirror.
3. Connect the cigarette lighter cable
to power connection..
5. Connect the CLA to the 12V
power socket.
▶Front Camera Installation
5Product Installation
7
All manuals and user guides at all-guides.com

Non LCD FHD-HD DASHCAM
▶Title of Recorded Video Files
6Recorded Video
8
Title of
recorded file aaab_cccc_dddddd_eeeeee_f.avi
aaa Type of
recording Description Remarks
inf Normal recording inf0_0000_140120_091603_I.avi
evt Impact recording evt0_0000_140120_091603_I. avi
moe Motion recording moe0_0000_140120_091603_P
b channel Description Remarks
0 1 channel Front
1 2 channels Front+rear
cccc index Description Remarks
0000~9999 File order The index starts with 0. The last file index varies
depending on the size of SD card memory.
dddddd
Year, month, and
date created Description Remarks
YYMMDD 140120
eeeeee Time created Description Remarks
hhmmdd 091603
f Recording mode
Description Remarks
I Normal recording Turned on when ACC is on
E Event recording It can be set in Menu> Storage Setting> Normal
Recording/Event Recording.
P Parking recording Turned on when ACC is off
▶Properties of Recorded Video
Bitrate (bits per second)
Definition FHD Video HD Video
Ultra-high definition 11 Mbps 6 Mbps
High definition 9 Mbps 5 Mbps
Standard definition 7 Mbps 4 Mbps
1ch Recording (bps) 2ch Recording (bps)
Normal Parking Normal Parking
Front Rear Front Rear
Ultra-high
definition 11 11 11 6 11 6
High definition
9 9 9 5 9 5
Standard
definition 7 7 7 4 7 4
FPS (Frame per second)
1ch Recording (FPS) 2ch Recording (FPS)
Normal Parking
Normal Parking
Front Rear Front Rear
Ultra-high
definition 30 30 30 30 30 30
All manuals and user guides at all-guides.com

Non LCD FHD-HD DASHCAM
9
7Recorded File
Each recorded file will be saved using the format-free system based on file size.
Normal : 120 MByte
Event : 60 MByte
Motion : 60 Mbyte
▶Size of Recorded File
▶Recording Time by SD Card Size
(Unit: Minute)
Chan
nel
Definition
Camera
16GB 32GB 64GB
Normal
(50%)
Motion
(20%)
Event
(30%)
Normal
(50%)
Motion
(20%)
Event
(30%)
Normal
(50%)
Motion
(20%)
Event
(30%)
1
Chan
nel
Ultra-
high
definition
Front 96 39 58 196 78 117 394 158 236
High
definition
Front 118 47 71 239 96 143 482 193 289
Standard
definition
Front 151 61 91 307 123 184 619 248 372
2
Chan
nels
Ultra-
high
definition
Front/Rear
62 25 37 127 51 76 255 102 237
High
definition
Front/Rear
72 30 45 154 61 92 310 124 290
Standard
definition
Front/Rear
96 39 58 196 78 117 394 158 373
By time : When the memory capacity runs out, recorded files will be automatically deleted beginning with
the oldest one.
By type : The percentage of allowed memory usage is set per recording type. When the memory capacity
for a recording type runs out, recorded files of the recording type will be automatically deleted
beginning with the oldest one. Recordings of an accident can also be deleted.
FHD + HD
▶On-Screen Display (OSD) Description
(1) Model name : LG INNOTEK LGD521
(2) F/W Version : V :1.0.772
(3) Date recorded : 2016/11/28 MON 10:07:51
(4) G-Sensor Value : X :-0.2 Y :-0.0 Z :-0.9
(5) Speed (Displayed only when GPS is connected) :
(6) Voltage : Input voltage
(7) INDEX (aaaabbbbcccc)
①aaaa : Normal file index
②bbbb : Event file index
③cccc : Motion file index
All manuals and user guides at all-guides.com

Non LCD FHD-HD DASHCAM
10
8Recording Scenario
①Recording of an impact event in the driving mode
A buffer video of 10 seconds will be included in the video when an impact event occurs in the driving mode.
If the power supply is cut off immediately after an impact event while driving, the event recording at the end may
not be performed normally. In this case, you can refer to the normal recording of the same timeline.
②Recording of multiple impact events in the driving mode
If another event occurs during impact event recording, the second event can be processed 10 seconds after
occurrence of the first impact event.
After the first impact event file is saved, the second one is saved.
If the second impact event happens after or at the same time with the completion of the first impact event, the
recording of the second impact event will start 10 seconds before the completion of the first impact event.
Once an event happens and a new file is created, the second event will not be recognized for 10 seconds after
occurrence of the first event.
▶Driving Mode
This refers to the recording while the vehicle is parked with ACC off.
Motion event is not recognized within 10 seconds after switching to the parking mode. The product can sense a
motion 10 seconds later.
▶Parking Mode
①Recording of an impact event in the parking mode
A buffer video of 10 seconds will be included in the video when an impact event occurs in the parking mode.
②Recording of multiple impact events in the parking mode
If another event occurs during impact event recording, the second event can be processed 10 seconds after
occurrence of the first impact event. After the first impact event file is saved, the second one is saved.
If the second impact event happens after or at the same time with the completion of the first impact event,
the recording of the second impact event will start 10 seconds before the completion of the first impact event.
Once an event happens and a new file is created, the second event will not be recognized for 10 seconds after
occurrence of the first event.
③Recording of a motion event in the parking mode
A buffer video of 10 seconds will be included in the video when a motion event occurs in the parking mode.
④Recording of multiple motion events in the parking mode
If another motion event occurs during motion event recording, the second event can be processed 10 seconds
after occurrence of the first motion event. After the first motion event file is saved, the second one is saved.
If the second motion event happens after or at the same time with the completion of the first motion event,
the recording of the second motion event will start 10 seconds before the completion of the first motion
event.
⑤Recording overlap of a motion event and an impact event in the parking mode
If an impact event occurs together with a motion event, recording of both events will overlap during the
parking mode.
A buffer video of 10 seconds will be included in the impact event video when an impact event occurs during
motion recording. (This is the same even when a motion event occurs during impact recording.)
If another event occurs during the overlap of an impact event and a motion event, the product follows the
scenario for recording of multiple events for the corresponding event type.
▶Switching the Mode
①Driving mode > Parking mode
Automatic switching: If ACC is cut off in the normal recording mode, the product enters the parking mode
10 seconds later.
②Parking mode > Driving mode
Automatic switching: If ACC power is high, the product automatically switches to the driving mode.
9Channel Switching Scenario
▶Scenario for Switching between 1-Channel and 2-Channel
Automatic Recording
If the rear camera is removed when the product is set to 2 channels, the 2-channel recording
continues and the rear screen shows black frames.
The rear connection alarm sounds once and repeats every 10 seconds. This can be stopped by
changing the rear connection or the channel settings.
At this time, the recording may be stopped for 1 - 3 seconds.
All manuals and user guides at all-guides.com

Non LCD FHD-HD DASHCAM
11
10 LED Operation
▶Front Security LED and User Notice LED
Item
Status
GPS
(Blue)
Security
(White) Remark
2 Channel 1 Channel
WLAN ON
(Green)
WLAN OFF
(Red)
WLAN ON
(Green) WLAN OFF (Red)
Booting Blink alternately
Recordin
g
SC card not
inserted OFF ON
Normal Green ON Red ON
Green 3
seconds /Red
1 second
Red 3 seconds
/Green 1 second Blinks (1 sec.)
Event WLAN ON Green/ WLAN OFF Red blink (1 sec.) Blinks (50 m)
Normal
Parking
Motion WLAN ON Green/ WLAN OFF Red blink (500 msec.) Blinks (500
msec.)
Parking
Motion
Parking Green ON Red ON Green ON Red ON ON Not
recorded
Not installed OFF
Not Fixed Blinks (1 sec.)
Fixed ON
Front Security LED operates only when the language is set to Korean or Chinese (refer to the table above).
If the language is set to others (Japanese, English, Spanish, and French), the Security LED is turned off.
If you change the LED settings through WLAN or PC Viewer, the changed settings apply.
Note 1) If you select "1 Channel" in the settings when 2 channels are connected, the product follows the
scenario for 2-channel connection.
▶Power Management
11 Low Voltage Cut-off
You can set the constant power cut-off voltage to Disable (11V) or 11.4 - 12.2 (23.1 - 24.3) V on the Viewer.
If an event occurs (and the event file is saved) with the voltage remaining below the cut-off limit and if the
voltage does not rise above the cut-off limit for 30 seconds or more, this product is turned off.
The constant power cut-off function is not enabled in the driving mode. It is enabled only in the parking mode.
▶Display on the Viewer
The Viewer displays as follows:
Disable is set to 11.0 (23.0) V.
0 Disable
1 11.4(23.1)V
2 11.6(23.4)V
3 11.8(23.8)V
4 12.0(24.0)V
5 12.2(24.3)V
All manuals and user guides at all-guides.com
all-guides.com

Non LCD FHD-HD DASHCAM
12 High Temperature Cut-off
The temperature cut-off function is used to protect the product from high temperature.
The high temperature cut-off function is not enabled in the normal mode.
The temperature cut-off function is enabled only if the "Use temperature cut-off" option is set to "Yes" in the
black box viewer.
If the product stops operation due to high temperature, recording stops and the product turns off.
The cut-off temperature is based on the temperature outside the product (inside the vehicle) and is 76±5℃.
The temperature detected by the internal temperature sensor is 110℃. (Room temperature 71 - 75℃)
If the temperature cut-off function is activated, recording and motion detection stop, and the front/rear LEDs
turn off with a voice message "Turning off".
▶G Sensor Operation
13 Sensor Operation
Based on events while driving (1: most sensitive, 5: least
sensitive)
Viewer OFF 5 4 3 2 1
Gravity 4.0 1.1 0.9 0.7 0.5 0.3
Based on events when parked (1: most sensitive, 5: least
sensitive)
Viewer OFF 5 4 3 2 1
Gravity 12.0 0.35 0.28 0.22 0.17 0.13
▶Motion Event Activation
You can set the sensitivity of a motion event activation.
If you set the sensitivity too high, a motion event is activated by very small changes, creating too many
motion events.
Stage 0 1 2 3 4 5
Sensitivity OFF Very
Sensitive Sensitive Normal Insensiti ve
Very
Insensitive
14 Using Multi-Key
▶Resetting the Product
Press and hold the multi-key button for 9 seconds until the product rings three times. If you release the
button when it rings three times, the product repeats ringing three times for 20 seconds. If you press the
multi-key button once again within 20 seconds, the product is reset with a message "Turning off". If you
do not press the button again within 20 seconds, the product rings once differently and the reset is
cancelled.
▶Changing the Language
If you press and hold the multi-key button for 9 seconds or more, you can hear a voice message changing
according to different languages. Release the button when you hear the language you want. Then, the
language changes to the one you want.
The language switches in the order of English > French > Japanese > Chinese > Korean.
▶Microphone On/Off
If you press and hold the multi-key button for 3 seconds, the product rings once. If you release the button
when it rings, the microphone turns on with a message "The microphone is turned on". If you repeat the
above procedure, the microphone turns off with a message "The microphone is turned off".
▶WLAN Function On/Off
WLAN is always off when the product boots. You can use the multi-key to set it to "On".
To turn it on manually, press and hold the multi-key button for 6 seconds until the product rings twice. If
you release the button when it rings twice, WLAN is turned on with a message "Wi-Fi is turned on": If you
repeat the above procedure, WLAN turns off with a message "Wi-Fi is turned off".
If the outside temperature stays above 55℃ for 30 seconds or more, WLAN automatically turns off to
protect the WLAN module. WLAN stays turned off even if the outside temperature falls below 55℃.
12
All manuals and user guides at all-guides.com

Non LCD FHD-HD DASHCAM
13
To insert or remove a SD card to and from the product, you need to turn off the product first.
▶Automatic Formatting
Update is performed only when you insert a SD card with the update firmware and restart the product by turning it
off/on.
When booting, if the SD card has an unsupported file system, a voice message is heard asking whether to format the
card. If you want to format the card, press the multi-key button once.
Even if the SD card contains the setup.cfg file, if the card is not formatted in the black box (if it is formatted in the
PC), the black box asks whether to format the card.
▶Manual Formatting
To manually format the SD card, turn on the product while pressing and holding the multi-key button. Press and
hold the button until booting is completed.
When you hear a voice message asking whether to format the card, release the multi-key button. Then press the
button once again to format the card. To exit the format mode without formatting the card, turn off the power
switch.
15 SD Card
16 Time Settings
▶Setting the Time Zone (GPS connected)
You can change the time zone in the Time Zone option under System Settings of your smartphone app. The
changed time zone is a time zone relative to GMT/UTC and is applied when the GPS is connected.
▶Setting the Current Time (GPS not connected)
If you connect the product to your smartphone, the smartphone time is applied as the time of the black box.
In the Viewer, change the time under the Default Settings menu and change "Apply Time Settings" to "Yes". Insert
the SD card with the saved settings to the black box and boot it to set the time of the black box. When you set the
time using the Viewer, you must consider the time needed to insert the SD card and boot the black box.
All manuals and user guides at all-guides.com

Non LCD FHD-HD DASHCAM
14
17 Linking the Viewer with the Smartphone
App
▶PC Viewer System Requirements
①Windows PC Viewer
OS : Windows 7 (32/64 bit) or higher
CPU : Intel core i3 or higher
RAM : 2 GB or higher
Display : 1920x1080 or higher
②MAC PC Viewer
OSX : 10.11.x (OS X El Capitan) or higher
▶Operating Conditions and Specifications of Smartphone App
①Android phone : Android 4.4 or higher recommended
Galaxy S3 or later or an equivalent model supported
LG Optimus G or later or an equivalent model supported
②iPhone : OS 10.0.2 or higher recommended
iPhone 5 or higher supported
18 Applying Variable Bitrate for Smartphone
WLAN
* wifi bitrate : Front 4M / Rear 2M
* Ultra quality bitrate : Front 11M / Rear 6M
* Recording definition :
- Front : Ultra-high definition (11M)/high definition (9M)/
standard definition (7M)
- Rear : Ultra-high definition (6M)/high definition (5M)/
standard definition (4M)
Mode Action Remarks
Recording
mode
Entering the live view Wi-Fi bitrate applied with a ringing sound
Switching live view channels
Wi-Fi bitrate maintained
live view exit After 30 seconds, bitrate switches to the standard bitrate with a ringing
sound.
Re-entering the live view
within 30 seconds Wi-Fi bitrate maintained
Entering the
parking mode in the
live view
Live view ends without switching to the parking mode. Bitrate
switches to the standard bitrate 30 seconds later. After
additional 10 seconds, the product switches to the parking
mode.
Entering the parking
mode within 30
seconds after ending
the live view
Live view ends without switching to the parking mode. Bitrate
switches to the standard bitrate 30 seconds later. After
additional 10 seconds, the product switches to the parking
mode.
Entering the parking
mode 30 seconds or
more after ending the
live view
Bitrate switches to the standard bitrate. 10 seconds later, the product
switches to the parking mode.
Parking
mode
Entering the live view
The product re-enters the parking mode after applying the Wi-Fi bitrate.
The product rings once and produces a voice message related to parking
recording.
live view exit
After 30 seconds, the product switches to the standard bitrate and re-
enters the parking mode. The product rings once and produces a voice
message related to parking recording.
1) If you use the live view function with an Wi-Fi app, the bitrate decreases to 4 Mbps.
2) If you exit the live view, the bitrate returns to the original setting 30 seconds later.
3) When the bitrate is changed, recording stops temporarily and restarts with a ringing sound.
All manuals and user guides at all-guides.com

Non LCD FHD-HD DASHCAM
▶Before use
LG Innotek Smart Manager Application
▶Smartphone Wireless Setting (iOS)
1. Turn on wireless on the Smartphone
configuration menu.
2. Select ‘LGD 5series’ network on the
wireless list.
3. Press ‘Connect’ after enter the password
[00000000]
LGD5series
15
Real time video and playback can be delayed depending on the type of Smartphone.
Do not use the application during driving. It may cause accident.
(Please use it always during parking or stop.
Please check wireless signal or the setting if the application can’t be connected to the product
for the first connection.
When [Internet Service Check] menu is ‚On‛ on wireless setting, try again after changing to ‚Off‛.
Try again after all setting on wireless ‚Signal Sensitivity Setting‛
Wireless disconnection can occur depending on a receiving sensitivity and interference
Stable wireless connection can be used in the vehicle.
During wireless connection, FPS can be different depending on the type of Smartphone.
Auto recovery will be operated when wireless is disconnected.
Android phone : LG Innotek recommends above Android version 4.4
Ex) Samsung Galaxy S3/LG Optimus G or equivalent specification
Apple : LG Innotek recommends above iOS version 10.0.2 (iPhone 5)
Application is available for both Android and iOS.
Search ‚LG Innotek‛ in Google Play Store or Apple iOS App Store..
Google Play Store App Store
19 Smartphone APP Download
All manuals and user guides at all-guides.com

Non LCD FHD-HD DASHCAM
16
20 Using the Smartphone App
▶Home Screen
1) Version: Displays the version of the app.
2) Reset the password : Resets the WLAN password saved in your phone (not the black box password) to 00000000.
(This function is supported only in an Android phone and not in an iPhone.)
※ When the black box is reset in the factory, the black box WLAN password is set to 00000000.
※ Changing the password using the smartphone app will change both the smartphone and black box passwords.
If the passwords saved in your smartphone and black box do not match, you need to reset the black box to the factory
default and reset the password in the smartphone for synchronization.
※ Since iPhone does not save the black box password, it does not have the "Reset the password" button.
3) START : Connects the black box to WLAN.
※ If the connection is carried out successfully, the black box rings once and sets the system time of your phone to the
black box time, and the screen changes to the menu screen.
※ Since an iPhone starts the app after connecting to WLAN manually, iPhone does not display the connection screen and
the list of connected access points (AP) and goes to the main menu screen directly.
1) Connect instantly if a recently connected black box AP is displayed.
2) If a recently connected black box is not found and if there are two or more black boxes available for
connection, the list of black boxes appears so that you can choose one.
3) If the connection screen does not move to the next step, connect to WLAN directly from the WLAN settings
of your phone.
※ If the Smart Network Switching function is selected, the connection may be lost repeatedly.
So, it is recommended to deselect the function.
(The menu for setting this function varies depending on the mobile phone manufacturer.)
Select a menu to go to the relevant screen.
▶Main Menu Screen
All manuals and user guides at all-guides.com
all-guides.com

17
▶Live View
※ Touch "Live View" to start live view with a ringing sound in the black box. The screen definition of the recording saved
in the black box switches to 4 Mbytes for front and 2 Mbytes for rear.
※ 30 seconds after the live view ends, the screen definition switches back to the standard definition with a ringing
sound. This applies to both parking and normal modes.
1) Touch the screen to display the control menu at the bottom.
2) R : Switch to the rear view (F : Switch to the front view).
3) VOD : Move to the VOD list.
▶VOD View
1) To play a stored video, select a video and press the Play button.
2) Select a channel to play (front/rear) to start playing.
3) Touch the VOD Play screen to display the control menu at the bottom.
4) When playing a VOD video, you cannot adjust the seek bar using the control menu.
The total time will be displayed as 5 minutes if the video is currently being recorded or ended abnormally.
5) Press the Download button to download the selected video to your smartphone.
▶Download View
1) It displays videos downloaded to your smartphone. You can play the video in the same way as VOD play.
2) When playing a downloaded video, you can adjust the seek bar using the control menu.
The total time will be displayed based on the actual video duration even for abnormally recorded videos.
All manuals and user guides at all-guides.com

18
▶Configuration
1) You can fetch the values set in the black box and change the basic settings or system settings.
You need to press the Transmit button to apply the settings to the black box.
2) Transmit : Press the Transmit button at the top after changing values to transmit the changed values to the black box
and reboot the black box.
Rebooting turns off WLAN in the black box, so you need to turn it on to reconnect.
3) Reset : Resets the changed values to the default settings.
Reset the changed values to the default settings and transmit them to apply them to the black box. To fetch the
settings from the black box, go back to the main menu and re-enter the Settings screen to read the black box settings.
4) Format SD Card : Formats the SD card in the black box and restarts normal recording.
After formatting, the connection between the app and the black box is lost and the app switches to the home screen.
After formatting, the black box restarts recording without rebooting.
5) WLAN Settings
(1) You can set or reset the password to connect to the black box via WLAN.
It changes both passwords saved in the black box and the smartphone.
(2) The password needs to be composed of 8 characters, combining English alphabets (case sensitive) and numbers.
(e.g.12345678, qwer1234)
(3) After the setting is completed, the black box reboots and the WLAN app switches to the home screen.
(4) After the black box reboots, you need to turn on WLAN in the black box again to reconnect.
(5) The changed password is saved in the smartphone, and you can reconnect to the black box without re-entering the
password.
(6) You can reset the black box password without using the WLAN app by resetting the black box to the factory
default. In this case, you need to reset the smartphone password in the home screen of your WLAN app in order to
synchronize with the black box.
▶F/W Update
Performing Update Using the App
1) Download the latest firmware from the server.
http://www.lginnotek.com > Customer Support > Black Box > Firmware Download
2) Copy the downloaded firmware file to the /LGInnotek/firmware/ folder in your smartphone.
(In the case of an iPhone, copy it to the Documents/mmc/ folder in the app.)
3) Start the smartphone app to connect to the black box.
4) The firmware copied to your smartphone is displayed under the New F/W Version menu.
5) Press the upload button to upload the latest firmware to the black box.
6) After uploading the firmware, the WLAN app switches to the home screen, and the black box reboots to start
the update automatically.
7) The black box reboots after the update is complete.
8) After the black box reboots, you need to turn on WLAN again in the black box to reconnect.
Performing Update Using the PC
1) To update using a SD card, save the firmware for update in the SD card.
2) Then turn off and on the black box with the SD card inserted to start the update.
All manuals and user guides at all-guides.com

Non LCD FHD-HD DASHCAM
21 Using the PC Viewer
▶Screen Organization
<Windows PC Viewer>
- LG Innotek recommends above
Windows7(32/64bit)/Intel core i3/RAM 2GB/Display 1920x1080
< MAC PC Viewer>
- LG Innotek recommends above OSX : 10.11.x (OS X El Capitan)
19
8
2 3 4 5 6 7
10
1
9
28
13 14 15 16 17 18 19 20 21 22
23 24 25 26 27
11
12
Item Description Item Description
1Front channel/Front&rearchannels 15 Play the previous file
2Viewer settings
16 Move 5 seconds backward
3Black box settings 17 Play or pause
4Print the video 18 Stop
5Capture the video 19 Move 5 seconds forward
6Zoom 20 Play the next file
7Separate the files 21 Adjust voice volume
8
Switch between the video list and the map
screen
22 Total file duration/play time
9Find file location
23 Brightness/Saturation
10 Screenfor switching betweenthe video
list and the map screen 24 GPS signal strength
11 Play bar 25 Drivingspeed
12 Switchto full screen 26 Latitude/Longitude
13 Flip horizontally 27 G sensorinformation
14 Flip vertically 28 Play screen
All manuals and user guides at all-guides.com

Non LCD FHD-HD DASHCAM
Item Description
JPEG Storage Path Set the storage path of captured screen image files.
Select Language Select user language.
Play Mode Set the number of channels.
Repeated Play Set whether to play the video repeatedly.
Always at the Top Set whether to display the viewer window always at the top.
Flip Video Set the vertical/horizontal flip of a video.
Product Model Select the product model.
Video Adjustment Show the brightness/contrast/saturation of the Viewer play screen.
Volume Show the video volume of the Viewer play screen.
▶Viewer Settings
20
21 Using the PC Viewer
Video Adjustment
Brightness Contrast Saturation
Volume
JPEG Storage Path
Select Language
Play Mode
Repeated Play
Always at the Top Yes
Yes No
No
Flip Vertically Flip Horizontally
Flip Horizontally
Flip Vertically
Rear Camera
Front Camera
Flip Video
Product Model
Version/Build Date
Device Information
DLL Version
Reset OK Cancel
All manuals and user guides at all-guides.com