LG 32LS350S.ABG User manual

User Guide
This is a 「User Guide」 installed on the TV.
The contents of this guide are subject to change without prior notice for quality
improvement.

GP2

 
 
 

 
 

 




GP2
eng
❐Automatically Setting Up Programme
SETTINGS ➾ SETUP ➙Auto Tuning
Automatically tunes the programmes.
1 Select Country where the TV is used. Programme settings change depending
on the country you choose.
2 Initiate Auto Tuning.
3 Select Input Source of your choice.
4 Set Auto Tuning following screen instructions.
✎If Input Source is not connected properly, programme registration may not
work.
✎Auto Tuning only finds programmes that are currently broadcasting.
✎If Lock System is turned on, a pop-up window will appear asking for
password.

GP2
eng
❓Cable DTV Setting option
When searching for programmes using FULL setting it can take a long time. The
following values are needed in order to search all available programmes quickly
and correctly. The commonly used values are provided as “default”.
• Frequency : Enter a user-defined frequency.
• Symbol rate : Enter a user-defined symbol rate (Symbol rate: Speed at which
a device such as modem sends symbols to a channel).
• Modulation : Enter a user-defined modulation. (Modulation: Loading of audio
or video signals onto carrier).
• Network ID : Unique identifier allocated for each user.
• Start Frequency : Enter a user-defined start frequency range.
• End Frequency : Enter a user-defined end frequency range.

GP2
eng
❓Satellite Setting Option
• Satellite : Select your desired Satellite.
• LNB Frequency : Select one value from 9750/10600, 9750/10750, 9750,
10600,10750, 5150. If you select 9750/10600, 9750/10750(MHz), 22KHz Tone is
disabled. If you cannot find the LNB frequency value from the list, select User
and manually enter the frequency.
• Transponder : Select the transponder you want to tune.
• 22KHz Tone : When using 22KHz Tone switch, select A or B. If you use 22KHz
Tone, Unicable and Motor Type are disabled.
• LNB Power : To enable the power supply for the LNB, select On. If you select
Off, Motor Type is disabled.

GP2
eng
• DiSEqC : When using DiSEqC, select one option from A~D/ToneA~B. If you
use DiSEqC, Unicable and Motor Type are disabled.
• Unicable Settings : Select On to use Unicable and set the Unicable in the
Unicable Setting menu. When Unicable is enabled, 22KHz Tone, DiSEqC,
Motor Type are disabled.
• Motor Type : Select Motor Type to use Motor and set the Motor in the Motor
Setting menu. When Motor is enabled, 22KHz Tone, DiSEqC, Unicable are
disabled.
✎If you set satellite to others, you must add a transponder using Manual
Tuning.
✎When selecting 22KHz Tone and DiSEqc, you must connect them in the same
position as displayed on the OSD.
✎If you delete a Satellite, all programmes stored in the Satellite are deleted.

GP2
eng
❓Motor Setting Option
• DiSEqC 1.2 : Control motor to change satellite dish position.
Drive Direction : Select the direction in which you want to move the motor.
Drive Mode : Two modes are available: Step and Continuous.
-Step: The motor moves based on the value you ente r (from 1 to 128).
-Continuous: The motor moves continuously until you press the Stop.
Test TP : Select the test TP you want to tune.
Set Limit : Set the motor movement to east or west to have the motor move
only within the direction set.
-On: You can limit the movement to the current direction by selecting the
West/East.
-Off: You can cancel the limit you set.

GP2
eng
Go To Zero: You can move the motor to Zero
Store: You can save the motor’s current direction.
• USALS : Set your current location(Longitude/Latitude).

GP2
eng
❐Cable DTV Setting
SETTINGS ➾ SETUP ➙ Cable DTV Setting
[In Cable, Cable & Satellite mode only]
When Channel Auto Update is On, you can update information for all the
programmes that can be updated, including the programme currently being
watched. When Channel Auto Update is Off, you can only update information for
the programme currently being watched.
✎The range that a user can select from the Service Operator menu differs
depending on number of Service Operator supported by each country.
✎If number of supported Service Operator for each country is 1, corresponding
function becomes inactive.
✎You can not select the Cable DTV Setting when the service operator is set to
“Ziggo”.

GP2
eng
❐Satellite Setting
SETTINGS ➾ SETUP ➙ Satellite Setting
[In Satellite, Antenna & Satellite, Cable & Satellite mode only]
You can add/delete/set the satellite you want.