LG 49UV760H.AHK User manual

INSTALLATION MANUAL
LED TV*
Please read this manual carefully before operating your
set and retain it for future reference.
www.lg.com
UV76**

ENG
ENGLISH
2TABLE OF CONTENTS
TABLE OF CONTENTS
3 LOCATION AND FUNCTION OF
CONTROLS
3 Parts and Button
4 EZMANAGER
4 INTRODUCTION
4 EZ-MANAGER WIZARD
5 LANGUAGE & COUNTRY SELECTION
6 - Automatically for Setup
9 - Manually for Setup
13 - USB LG Smart Install Utility
16 INSTALLATION MENU
16 INTRODUCTION
17 LG HOTEL MODE
17 - Hotel Mode Operation
17 - Power On Status
18 - Volume
18 - Key Management
19 - Limited Mode
19 - DTV Programme Update
20 - Power On Default
20 - Aux Source Setting
20 - Power Management
20 - Radio Video Blank
20 - Factory Reset
21 NETWORK
21 - MAC Address
21 - Network Setting
22 - LG Connect
22 - Wake On LAN
23 PRO:CENTRIC
23 - Mode
23 - WORF
23 - Room Number Setting
24 - Media Type
24 - Receive Data
24 - Native EPG
25 GENERAL
25 - Configuration Setup
29 - External Speaker
30 - Set ID Setup
30 - Power Saving
30 - HCEC Setup
31 - Clock Setup
32 - Password Change
32 - PreLoaded App
32 - Lock Mode
33 MEDIA SHARE
33 - SmartShare
33 - Screen Share
33 - Media Renderer
34 - DIAL
34 - TV Name
34 - SoftAP
35 TV MANAGER
35 - USB Download Menu
43 KEY CODES
46 EXTERNAL CONTROL DEVICE
SETUP
46 USB to Serial converter with USB Cable
46 RS-232C With RS-232C Cable
47 - Type of connector : D-Sub 9-Pin male
47 - RS-232C Configurations
48 IR OUT Using Guide
49 Communication Parameters
49 Command reference list
50 Transmission / Receiving Protocol

ENGENGLISH
3
LOCATION AND FUNCTION OF CONTROLS
LOCATION AND FUNCTION OF CONTROLS
Parts and Button
Screen
Remote control and
Intelligent1sensors
Power Indicator
1 Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment.
2 Button - This button is located below the TV screen.
NOTE
yYou can set the power indicator light to on or off by selecting General in the main menus.
Button2

ENG
ENGLISH
4EZMANAGER
EZMANAGER
•
• Image shown may differ from your TV.
INTRODUCTION
The Pro:Centric Platform enables you to simply install, manage and use guest-centric solutions.The default Domain“procentric.local”
and IP Server Address are needed to be registered in DNSTV will contact the IP Server using the default Domain “procentric.local”via IP
on server search page. IfTV doesn’t contact the Server, TV will search the pre-defined channel earlier than all channels. (Only DVB-C)
The frequencies of pre-defined channels are below.
Germany:‘51000, 858000, 778000, 698000, 618000, 538000, 458000, 378000, 298000, 218000, 138000 khz’.
Philippines 6Mhz:‘57000, 651000, 591000, 531000, 471000, 411000, 351000, 291000, 231000, 171000, 111000 khz’.
Other Country:‘50000, 842000, 762000, 682000, 602000, 522000, 442000, 362000, 282000, 202000, 122000 khz’.
EZ-MANAGER WIZARD
-If you are using Pro:Centric, this setup wizard till help you easily set up theTV. Select ‘NEXT’to continue.
-Otherwise, if you will not be installing a Pro:Centric Server, select‘X’to quit.

ENGENGLISH
5
EZMANAGER
LANGUAGE & COUNTRY SELECTION
-Please select the Language and Country. Some countries need to select the Time Zone.

ENG
ENGLISH
6EZMANAGER
Automatically for Setup
1 From theTV Conguration Options screen, you can choose how to proceed with the conguration of this TV. Whether you will
congure theTV for Pro:Centric operation via the wizard or use a USB memory device to congure theTV, you may rst wish to set
the Room Number on the TV.
-If you intend to set Room Number as part of the TV configuration, use the Room Number option to assign the Room # for
this TV before you continue with additional configuration.
-In the Label field, use the Left/Right arrow keys to specify a North, South, East, orWest designation for thisTV.
-In the Room Number field, you can use the number keys on the Installer Remote to direct enter a room number or use the
virtual keyboard on the TV screen.
-To continue, move and select‘NEXT’.

ENGENGLISH
7
EZMANAGER
2 This step automatically searches for the Pro:Centric Server. If was found the Pro:Centric data channel, select the‘NEXT’.

ENG
ENGLISH
8EZMANAGER
3 Downloading the Pro:Centric application les takes few minutes.
4 After the installation is completed, the following screen will be displayed.

ENGENGLISH
9
EZMANAGER
Manually for Setup
1 Select a Label and/or enter the Room Number using the numeric keypad on the remotes or using the virtual keyboard on the TV
screen.To continue, move and select ‘NEXT’.

ENG
ENGLISH
10 EZMANAGER
2 Please select the‘MANUAL PRO:CENTRIC’.
3 Congure the appropriate Pro:Centric settings in theTV. (Depending on model)

ENGENGLISH
11
EZMANAGER

ENG
ENGLISH
12 EZMANAGER
4 Downloading the Pro:Centric application les takes few minutes.
5 After the installation is completed, the following screen will be displayed.

ENGENGLISH
13
EZMANAGER
USB LG Smart Install Utility
1 Select the ‘USB CONFIGURATION’ → ‘TV MANAGER’.
-If you have USB Memory for“LG_DTV”or“lg_dtv”folder, this step shows the USB file list for downloading the items.

ENG
ENGLISH
14 EZMANAGER
-Detail information is described in TV Manager chapter of Installation Menu.
2 Downloading the les takes few minutes.
3 After the installation is completed, the following screen will be displayed.

ENGENGLISH
15
EZMANAGER
-

ENG
ENGLISH
16 INSTALLATION MENU
INSTALLATION MENU
•
• Image shown may differ from your TV.
INTRODUCTION
The abundant functions for HotelTV linked with software installation can be projected on OSD as‘Installation Menu’.
The wide range of hotel features can be performed simply on additional window to enhance the LG hotelTV’s easy installation and
convenient operation for Hotelier and System Integrators.
TV
1 Press the Setting button for more than 5 seconds using the user remote control, programme
information will appear at top left on the screen.
2 Enter a four digit password and press‘OK’ button.
-TheTV is set with the initial password“1-1-0-5”.
3 Use the button to select the desired menu.

ENGENGLISH
17
INSTALLATION MENU
LG HOTEL MODE
1 Use the button to select the LG HOTEL MODE SETUP.
2 Use the‘OK’button and then button to select Hotel Mode Operation.
-When‘Hotel Mode Operation’is set to On (Work), all functions of Hotel Mode apply.
Hotel Mode Operation
-Decide to work all functions of‘Hotel Mode Operation’or not by setting‘Hotel Mode Operation’as On(Work) or Off(Do Not
Work)
-When‘Hotel Mode Operation’is set to On(Work), all functions of Hotel Mode apply.
-When‘Hotel Mode Operation’is set to Off(Do Not Work), all functions of Hotel Mode Do Not apply.
-When it is set to‘On’, all items reserved at the Schedule list are deleted and the reservation function is not supported.(applied
for the model offering the reservation function)
-TheTV triggered by the external device (ex: SIMPLINK, TVLink-Tuner, etc.) operates separately from the Hotel mode.
-When it is set to‘On’, User Menu →General →‘Reset to Initial Settings and Home/Store Mode’are disabled.
-When‘Hotel Mode Operation’is set to On(Work), all skipped programs are not tuned by number keys.
-When‘Hotel Mode Operation’is set to On(Work), Detailed Information about the programme is not available in the EPG.
-When‘Hotel Mode Operation’is set to On(Work), User Menu ->Timer->’Auto Power Off’is disabled.
-When‘Hotel Mode Operation’is set to On(Work), User Menu ->Timer->’2 Hour Auto Power Off’is disabled.
Power On Status
-Decide to select working status ofTV Set when turn on main power.
-You can set with PWR, STD, LST.
-PWR always make TV set On status when turn on main power .
-STD make Stand-by status when turn on main power.
-LST makeTVSet work like previous power status. As same concept as Power Backup mode; If main power were turned off
in Power On status,TVSet would work in On status. If main power were turned off in Stand-by status, TVSet would work in
Stand-by status.
-If there Block All is both IR Operation and Local Key Operation from Key Management, In order to provide the Option
that must be able to turn on theTV in theTV turned off situation, change the value of the PWR. (Reference the Key
Management)

ENG
ENGLISH
18 INSTALLATION MENU
Volume
-Decide to apply volume policy of‘StartVolume’, ‘Maximum Volume’and ‘Minimum Volume’as On(Work) or Off(Do Not
Work).
-(0 ≤ Min ≤ Start ≤ Max ≤ 100)
Start Volume
yThis entry sets the start volume level when is power on.
-The level is specified as a number between minimum volume to maximum value. (Min ≤ Start ≤ Max)
-The default setting is‘Off’(disabled).
-When enabled, if the value is lower then the minimum specified in the minimum volume entry, the minimum volume
entry must be used.
-When enabled, if the value is larger then the maximum specified in the maximum volume entry, the maximum volume
value must be used.
-Access to a volume in‘On Timer’must be fixed to start volume when‘Hotel Mode Operation’(On) and‘Start Volume’(Off, 0
~ 100) were set simultaneously.
Maximum Volume
yThis entry sets the maximum volume level the set. The level is specied as a number between‘Minimum Volume’to 100. (Min ≤
Max ≤ 100).
-If the command volume up to higher than maximum volume’is received, that should be ignored.
-The default value is 100.
Minimum Volume
yThis entry sets the minimum volume level the set will produce.
-The level is specified as a number between 0 to‘Maximum Volume’. (0 ≤ Min ≤ Max)
-If the command volume down to lower than minimum volume is received, that should be ignored.
-The default value is 0.
Key Management
-Manage key usability of Local(Front) Key and Remote Control. When selected to‘On’, following‘IR Operation’and‘Local Key
Operation’will be worked by below.
IR Operation
yDecide whether work the LG remote control or not.
-When‘IR Operation’is set to 'Normal', all remote keys are available.
-'Use PWR Only' makes block all remote keys except power key.
-When‘IR Operation’is set to 'Block All', all normal remote keys don’t work.
Local Key Operation
yDecide to operate 'Local/Front Key' working behavior by setting‘Local Key Operation’as 'Normal', 'Use PWR Only' and 'Block All'.
-When‘Local Key Operation’is set to 'Normal', all local keys are available.
-'Use PWR Only' makes block all local keys except power key.
-When‘Local Key Operation’is set to 'Block All', all local keys don’t work.

ENGENGLISH
19
INSTALLATION MENU
Limited Mode
-Configure TV function’s limitation. When selected to‘On’, following sub-menus will be worked by below.
Setup Menu
-Permit to tune and manage programmes as 'On'(permitted) or 'Off'(not permitted).
Programme Change
yDecide to change channel or not by setting‘Program Change' as‘On’(Change Possible) or‘Off’(Change Impossible) when present
source is TV.
-When‘Programme Change' is set to Off (Change Impossible)
»Program Key, Numeral Key, List Key, Q.View Key don't work and entering 'Channel Menu' in the Main Menu OSD is
impossible.
»‘Programme' item in 'On Time' menu will be fixed.
»Entering 'Programmes' in the 'Main Menu’OSD is impossible regardless of 'Programmes' item.
-When 'Program Change’is set to On(Change Possible),‘Program Key’,‘Numeric Key’,‘List Key’,‘Q.View’Key, 'TV/RAD Key'
does work and entering‘Channel Menu' in the Main Menu OSD is possible.
Menu Display
yFunction to decide whether work with menu (including relevant menus too) of control key (On – Enter possible) or not (O – Enter
Impossible).
-Although select Off(Enter impossible), the action that press a Menu button for 5 seconds to enter‘Installation Menu’is
available.
-When select On(Enter possible), Menu works.
OSD Display
yDecide to display OSD or not by setting‘OSD Display’ as On(Display) or O(Do not Display).
-When‘OSD Display’is set to‘Off’(Do not Display), all OSD is not displayed except some exception.
-Although select‘Off’(Do not Display), the action that press a Menu button for 5 seconds to enter‘Installation Menu’and
entering service menu are available. (In-Start, Power-Only, Adjust, Installation Menu…)
System Provider Mode
y‘System Provider Mode’allows access to the menu system from the front panel or remote control but access is controlled as follows:
-When value is‘On’, Accessible Items on the menu system, others are not permissible.
»Input select screens
»Sleep timer
»Aspect Ratio
»Subtitles
»Programmes (Except for Programme Tuning & Settings and Programme Manager)
»‘Safety’/ 'Photo & Video' / 'Music' /‘Network’/‘Bluetooth’Menu
-If the channel map is empty,‘Auto-tuning’guide dialog should be blocked by pressing‘List’,‘CH+’,‘CH-’keys.
DTV Programme Update
-It is a mode to set whether to update dtv Programme automatically or not.
-When DTV Programme Update is set to‘Auto’, the function to update TV’s programme map according to dtv programme’s
stream information.
-DTV Programme Update is set to‘Manual’, the function to keep TV’s programme map even though dtv programme’s
information is changed.

ENG
ENGLISH
20 INSTALLATION MENU
Power On Default
-Set the channel to display andVolume Level, etc. when turn on power in AC Power On or Stand-by status.
-Set to On(Work) or Off(Do Not Work).
-When‘Power On Default’is set to Off, it is not applied to the subordinate Input, Programme, A/V Setting, Aspect Ratio
menu.
-When Power On Default is set to On, it can set by entering the subordinate menu.
Input
-Set whether it is turned on by the set input source or by the last stored input source.
Programme
-Select start channel number if Input source’s value is TV.
A/V Setting
-If‘A/V Setting’is changed from‘Off’to‘On’, A/V parameters that are set before entering‘Installation Menu’are applied
whenever turn on power.
Aspect Ratio
-The aspect ratio determines the default aspect ratio that the set returns to on power up.
Aux Source Setting
-Set to On(Work) or Off(Do Not Work).
-The Auxiliary (Input) Source Setting feature will enable or disable for each external input.
-User cannot disable the current input’s‘Aux Source Setting’.
Power Management
yThe Power Management feature will turn o the television receiver if no input control command is received from either the Local
or IR Key within a selected hours.
-Activity on either of these inputs shall reset the‘Power Management’timer and prevent interruption of TV viewing.
-This entry can be set to a value which is corresponding to the desired hours (1Hour to 7Hours).
-Default value is‘Off(disabled)’.
Radio Video Blank
-Set to On(Work) or Off(Do Not Work).
-Programme that is set to‘Radio Programme’and only has Sound should decide whether to set‘Video Blank’or not.
-When‘Radio Video Blank’is set to On(Work),‘Video Blank’works only in case of Radio Programme.
-Although set to On(Work), if there are Video signal,‘Video Blank’wouldn’t work. In consideration of case that display
background screen and broadcast only with Radio,‘Video Blank ’works only when there is noVideo signal.
-When set to Off(Do Not Work),‘Video Blank’do not work although it is the Radio Programme.
-This operates only in the Analog TV Mode.
Factory Reset
-Change all settings to their default values.