Lg E2040s User manual

Only

Only for training and service purposes



North/Latin America http://aic.lgservice.com

Europe/Africa http://eic.lgservice.com

Asia/Oceania http://biz.lgservice.com

COLOR MONITOR

SERVICE MANUAL

MODEL:E2040S (E2040S-PNT.A**NAV for

LGD -TLA1)**SalesMarket

CAUTION

BEFORE SERVICING THE UNIT,

READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

*ToapplytheNovatekChip.

Internal Use Only

Only

Only for training and service purposes

CONTENTS

SPECIFICATIONS ..........................................................2

PRECAUTIONS ..............................................................3

TIMING CHART ..............................................................7

DISASSEMBLY ...............................................................8

BLOCK DIAGRAM.........................................................11

DISCRIPTION OF BLOCK DIAGRAM ......................... 13

ADJUSTMENT ............................................................. 15

SERVICE MODE ......................................................... 17

TROUBLESHOOTING GUIDE .................................... 18

WIRING DIAGRAM ...................................................... 24

EXPLODED VIEW........................................................ 25

SCHEMATIC DIAGRAM............................................... 27

SPECIFICATIONS

1. LCD CHARACTERISTICS

Type: matrix-TFT Color LCD Module

ActiveDisplayArea:20inches

Pixel Pitch: 0.2766 x 0.2766 mm

Color Depth: 16.7M colors

Size: 462.8(H) x 272.0(V) x 11.5(D) mm(Typ.)

Interface: LVDS 2Port

Surface Treatment: Hard coating (3H), Anti-glare

treatment of the front polarizer

Operating Mode: Transmissive mode, normally

White

2. OPTICAL CHARACTERISTICS

2-1. Viewing Angle by Contrast Ratio ≥10

Left/Right: 170/150

Top/Bottom: 160/140

2-2. Luminance: 200Cd / m2-6500K;

150Cd / m2-9300K

2-3. Contrast Ratio:

700(Min), 1000(Typ)

3. SIGNAL (Refer to the Timing Chart)

3-1. Sync Signal

Type: Separate Sync, Composite

3-2. Video Input Signal

1) Type: R, G, B Analog

2) Voltage Level: 0.7 Vp-p

3) Input impedance: 75 Ω

3-3. Operating Frequency

Horizontal: 30 ~ 83kHz

Vertical: 56 ~ 75Hz

4. Max. Resolution

D-sub Analog: VESA 1600 x 900 @ 60 Hz

5. POWER SUPPLY

5-1. Power: 12V==2.0A

5-2. Power Consumption

On Mode: 21 W(Typ.)

Sleep Mode: ≤1 W

Off Mode: ≤0.5 W

6. ENVIRONMENT

6-1. Operating

Temperature: 10°C to 35°C

Humidity: 10 % to 80% non-Condensing

6-2. Storage

Temperature: -20°C to 60 °C

Humidity: 5 % to 90 % non-Condensing

6-3. MTBF: ≥187000 Hours before PRM

Lamp Life: > 30000Hrs

7. DIMENSIONS (with Stand)

Width: 49.68 cm (19.56 inches)

Depth: 20.2 cm (7.95 inches)

Height: 39.11 cm (15.40 inches)

8. WEIGHT (excl. packing)

Weight: 2.6 kg (5.73 lbs)



Only for training and service purposes



Only for training and service purposes



Only for training and service purposes



Only for training and service purposes



Only for training and service purposes

TIMING CHART

MODE

CLASSIFI

CATION

Polar

ity

DOT

CLOCK

[MHz]

Frequency

[kHz]/[Hz]

Total

Period

(E)

Display

(A)

Front

Porch

(D)

Sync.

(C)

Back

Porch

(B)

Resolution

1

H(Pixels) -

28.321

31.468 900 720 18 108 54

720 X 400

V(Lines) + 70.08 449 400 12 2 35

2

H(Pixels) -

25.175

31.469 800 640 16 96 48

640 x 480

V(Lines) - 59.94 525 480 10 2 33

3

H(Pixels) -

31.5

37.5 840 640 16 64 120

640 x 480

V(Lines) - 75 500 480 1 3 16

4

H(Pixels) +

40.0

37.879 1056 800 40 128 88

800 x 600

V(Lines) + 60.317 628 600 1 4 23

5

H(Pixels) +

49.5

46.875 1056 800 16 80 160

800 x 600

V(Lines) + 75.0 625 600 1 3 21

6

H(Pixels) -

65.0

48.363 1344 1024 24 136 160

1024 x 768

V(Lines) - 60.0 806 768 3 6 29

7

H(Pixels) -

78.75

60.123 1312 1024 16 96 176

1024 x 768

V(Lines) - 75.029 800 768 1 3 28

8

H(Pixels) +/-

108.0

67.500 1600 1152 64 128 256

1152 x 864

V(Lines) +/- 75.000 900 864 1 3 32

9

H(Pixels) +

108

60 1800 1600 24 80 96

1600 x 900

V(Lines) + 60 1000 900 1 3 96



Only for training and service purposes

DISASSEMBLY-Set

#1

Put the monitor on a soft flat.

#2

Press the release button.

#3

Consequently, pull the base directly.

#4



The base.

#5

Use tool to open all latches.

#6

Put the front face down, disassembly back

cover.



Only for training and service purposes

#7

Pull the key board out of bezel.

#8

Disassembly the LVDS cable.

#9

Disassemble the FFC cable and converter board

to converter board cables.

#10

Unscrew the 2 screws on the converter board.

#11

Unscrew the 4 screws on the main board.

#12

Remove the main board and the power board.

#13

Removethebezel.

#14

Thepanel.

Optional



Only for training and service purposes

#15

Rear cover and hinge ASS’Y.

#16

Disassemble the rear cover and the hinge ASS’Y.

#17

Disassemble the hinge and stand.

#18

Hinge top, hinge and stand.



Only for training and service purposes

BLOCK DIAGRAM

DDC-DSUB PORT

SCALAR NT68168FG/B

U401

DSUB

CN101

Crystal 12MHZ

X401

CN401 to Keyboard

A

/D in

p

ut control

RGB, H/V SYN

SCL, SDA, WP

Serial Flash

U402

To Inverter Block

Brightness control

CN302 to Panel

LVDS out

p

ut

Panel Power

sequence

control circuit

Block Q302

Q301

Power input

CN702

LDO

U701

3.3V



Only for training and service purposes

BLOCK DIAGRAM-CONVERTER

Converter

Boost Circuit Ignition LED bar

ON/OFF circuit

Current balance

Control IC ta9690 Feedback

circuit

OVP circuit

Current

Feedback

DIM circuit

12V

ON/OFF

DIM



Only for training and service purposes

DESCRIPTION OF BLOCK DIAGRAM

1. Video Controller Part.

This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the

digital video signal using a pixel clock.

The pixel clock for each mode is generated by the PLL.

The range of the pixel clock is from 25MHz to 108MHz.

This part consists of the Scalar, ADC converter, TMDS receiver and LVDS transmitter.

The Scalar gets the video signal converted analog to digital, interpolates input to 1600 X 900 resolution signal and

outputs 8-bit R, G, B signal to transmitter.

2. Power Part.

This part consists of the one 3.3V regulators to convert power which is provided 5V in Power board.

12V is provided for inverter board, 5V is provided for LCD panel.

Also, 5V is converted 3.3V by regulator. Converted power is provided for IC in the main board.

The inverter operates back-light lamps of module.

3. MICOM Part.

This part is including video controller part. And this part consists of Reset IC and the Micom.

The Micom distinguishes polarity and frequencies of the H/V sync are supplied from signal cable.

The controlled data of each mode is stored in scalar.



Only for training and service purposes

Converter Board Block Diagram

1. Boost circuit: Boost converter, the function is to convert 12V to the turn-on voltage of LED.

2. On/Off circuit: Main board provides ENA signal to make the converter system On or Off.

3. DIM circuit: Main board provides PWM signal to make the light LED On or Off.

4. IC ta9690: Converter controls IC, the function: provide PWM driver signal to Boost converter, balance the LED

current, set the maximum output voltage of OVP.

5. OVP circuit: set the maximum output voltage of OVP, through this voltage IC can neglect the OPEN’s string.

6. Current feedback: LED feedback current detection.



Only for training and service purposes

ADJUSTMENT

Windows EDID V1.0 User Manual

Operating System: DOS, windows98, 2000, XP

1. Parallel port setting

Enter your bios, and do as followings.

a) Integrated peripheral

b) Super IO Device

c) Parallel port mode

you should set the” parallel port mode” to SPP for using the DOS EDID tool surely.

2. EDID Write

1、Connect the signal line of monitor with DDC recorder.

2、Choose the DDC RECORD program, and it shows on the screen, the choose the correct source base on the

monitor.

3、Click “LoadFile” ,then key in the manufacturer name, model name, product code, then choose the correct

model name base on the monitor.(as Fig.2)

4、Scan serial No. to DDC recorder by Bar Reader, then read again in the Verify SN.

5、According to the message of DDC program, when the picture as fig.1 appears, it show DDC record has finished.

Fig.1



Only for training and service purposes

Please check Manufacturer Name, Vendor Assigned Code, Monitor Name, Serial Number：

*****[????????******] (it must be the same as Bar Code)、Week of Manufacture：**, Year of Manufacture：****,

Checksum：** (It must be the same as the last byte of data table, as follows picture shows). Above of all must be

right, then if it shows the green “PASS”, it means record succeeds ,the red “Fail” means record fails; Then check

the power supply and signal line, and ensure they are connected well ,then do DDC record again from the third

step.



Fig.2



Only for training and service purposes



1) Turn off the power switch at the front side of the display.

2) Wait for about 5 seconds and press MODE, POWER switch with 1 second interval, press MENU.

3) The SVC OSD menu contains additional menus that the User OSD menu as described below.

a) CLEAA ETI: NO

b) Auto Color: NO

c) AGING: Select Aging mode (on/off).

d) PANEL: Used panel type

e) NVRAM INIT: NO

f) R/G/B-9300K: Allows you to set the R/G/B-9300K value manually.

g) R/G/B-6500K: Allows you to set the R/G/B-6500K value manually.

h) R/G/B-Offset: Allows you to set the R/G/B-Offset value manually. (Analog Only)

i) R/G/B-Gain: Allows you to set the R/G/B-Gain value manually. (Analog Only)

e) R/G/B-sRGB: Allows you to set the R/G/B- sRGB value manually.

Figure 1 Cable Connection for Micom uploading

SERVICE MODE

Connect to

the PC Connect to

the monitor



Only for training and service purposes

TROUBLESHOOTING GUIDE

No Power

(Power Indicator Off)

Please reinsert and

make sure the AC of

100-240V is normal

Measure

U701 PIN2=3.3V



Check the Adapter/Inverter

section

Check CN702 or replace

U701

NO

YES

1. NO POWER

Check X401 oscillate

waveforms are normal

Replace X401



Replace U401



NO

YES



Only for training and service purposes

2. NO RASTER (OSD IS NOT DISPLAY)-LIPS

LIPS

YES

Check CN702

PIN 8 =5V?

NO Check BL ON/OFF pulse as

contacting scope

No Raster

(OSD Is Not Displayed)

Check U701

PIN 2 =3.3V?

Check CN702

PIN 8 =5V?

Check power board and find out a

short point as penning each power

line

1. Check U701

2. Check C706,C707,C708,C709

NO



Only for training and service purposes

3. NO RASTER (OSD IS NOT DISPLAY)-MSTAR

1. Check C416 C417

2. Check X401

3. Trouble in Scaler IC

Scaler pin 63, 64

oscillates as

12MHz?

No Raster

(OSD Is Not Displayed)

Check connection line from

D-SUB to Scaler

Trouble in cable or LCD

module

NO

YES

NO

Scaler IC

pin 14 H Sync ?

pin 15 V Sync?

LG E2040S User manual

Popular Monitor manuals by other brands