LG Flatron LB700G-GD User manual

MENU
AUTO
SELECT
COLOR MONITOR
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS NO. : CL-42
FACTORY MODEL: LB700G
MODEL: L1710S (LB700G-GU)
L1710S (LB700G-GD)

1. LCD CHARACTERISTICS
Type : TFT SXGA LCD
Size : 17 inch
Pixel Pitch : 0.264 (H) x 0.264 (V)
Color Depth : 6-bit + FRC(16.2M)
Electrical Interface : LVDS
Surface Treatment : Anti-Glare, Polarizer Hardness
Operating Mode : Normally White
Backlight Unit : 4-CCFL (Cold Cathode
Fluorescent Lamp)
2. OPTICAL CHARACTERISTICS
2-1. Viewing Angle by Contrast Ratio
≥
10
(AU Module)
Left : -55° min., -70°(Typ) Right : +55° min., +70°(Typ)
Top :+55° min., +70°(Typ) Bottom : -55°min., -70°(Typ)
(Hydis Module)
Left : -60° min., -65°(Typ) Right : +60° min., +65°(Typ)
Top :+40° min., +45°(Typ) Bottom : -60°min., -65°(Typ)
2-2. Luminance : 200(min), 250(Typ)
2-3. Contrast Ratio : 200(min), 450(Typ)
3. SIGNAL (Refer to the Timing Chart)
3-1. Sync Signal
• Type : Separate Sync,
SOG (Sync On Green)
Composite Sync
3-2. Video Input Signal
1) Type : R, G, B Analog
2) Voltage Level : 0~0.7 V
a) Color 0, 0 : 0 Vp-p
b) Color 7, 0 : 0.35 Vp-p
c) Color 15, 0 : 0.7 Vp-p
3) Input Impedance : 75 Ω
3-3. Operating Frequency
Horizontal : 30 ~ 83kHz (Digital: 71kHz)
Vertical : 56 ~ 75Hz
4
. Max. Resolution
Analog : 1280 x 1024 / 75Hz
5. POWER SUPPLY
5-1. Power : AC 100~240V, 50/60Hz , 1.0A
5-2. Power Consumption
6. ENVIRONMENT
6-1. Operating Temperature: 10°C~35°C (50°F~95°F)
(Ambient)
6-2. Relative Humidity : 10%~80%
(Non-condensing)
6-3. MTBF : 50,000 Hours(Min)
7. DIMENSIONS (with TILT/SWIVEL)
Width : 370 mm (14.57'')
Depth : 222.5 mm (8.76'')
Height : 421 mm (16.57'')
8. WEIGHT (with TILT/SWIVEL)
Net. Weight : 6.0 kg (13.23 lbs)
Gross Weight : 7.6 kg (16.76 lbs)
CONTENTS
SPECIFICATIONS
- 2 -
SPECIFICATIONS ................................................... 2
PRECAUTIONS ....................................................... 3
TIMING CHART ....................................................... 4
OPERATING INSTRUCTIONS ................................ 5
WIRING DIAGRAM ................................................. 6
BLOCK DIAGRAM ................................................... 8
DESCRIPTION OF BLOCK DIAGRAM.....................9
ADJUSTMENT ....................................................... 11
TROUBLESHOOTING GUIDE .............................. 12
PRINTED CIRCUIT BOARD................................... 15
EXPLODED VIEW...................................................18
REPLACEMENT PARTS LIST ...............................20
SCHEMATIC DIAGRAM......................................... 22
MODE
POWER ON (NORMAL)
STAND-BY
SUSPEND
DPMS OFF
POWER S/W OFF
H/V SYNC
ON/ON
OFF/ON
ON/OFF
OFF/OFF
-
POWER CONSUMPTION
less than 40 W
less than 3 W
less than 3 W
less than 3 W
LED COLOR
GREEN
AMBER
AMBER
AMBER
OFF
VIDEO
ACTIVE
OFF
OFF
OFF
-less than 1 W
(@120V AC)

- 3 -
WARNING FOR THE SAFETY-RELATED COMPONENT.
• There are some special components used in LCD
monitor that are important for safety. These parts are
marked on the schematic diagram and the
replacement parts list. It is essential that these critical
parts should be replaced with the manufacturer’s
specified parts to prevent electric shock, fire or other
hazard.
• Do not modify original design without obtaining written
permission from manufacturer or you will void the
original parts and labor guarantee.
TAKE CARE DURING HANDLING THE LCD MODULE
WITH BACKLIGHT UNIT.
• Must mount the module using mounting holes arranged
in four corners.
• Do not press on the panel, edge of the frame strongly
or electric shock as this will result in damage to the
screen.
• Do not scratch or press on the panel with any sharp
objects, such as pencil or pen as this may result in
damage to the panel.
• Protect the module from the ESD as it may damage the
electronic circuit (C-MOS).
• Make certain that treatment person’s body are
grounded through wrist band.
• Do not leave the module in high temperature and in
areas of high humidity for a long time.
• The module not be exposed to the direct sunlight.
• Avoid contact with water as it may a short circuit within
the module.
• If the surface of panel become dirty, please wipe it off
with a softmaterial. (Cleaning with a dirty or rough cloth
may damage the panel.)
WARNING
BE CAREFUL ELECTRIC SHOCK !
• If you want to replace with the new backlight (CCFL) or
inverter circuit, must disconnect the AC adapter
because high voltage appears at inverter circuit about
650Vrms.
• Handle with care wires or connectors of the inverter
circuit. If the wires are pressed cause short and may
burn or take fire.
PRECAUTION
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.

TIMING CHART
- 4 -
VIDEO
SYNC
B
D
CFE
A
<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >>
H + 31.469 800 640 16 96 48
V–70.8Hz 449 350 37 2 60
H–31.469 840 640 16 96 48
V–59.94 525 480 10 2 33
H–37.5 840 640 16 64 120
V–75 500 480 1 3 16
H–31.468 900 720 18 108 54
V + 70.09 449 400 12 2 35
H + 37.879 1056 800 40 128 88
V + 60.317 628 600 1 4 23
H + 46.875 1056 800 16 80 160
V + 75.0 625 600 1 3 21
H+/–49.725 1152 832 32 64 224
V+/–74.55 667 624 1 3 39
H–48.363 1344 1024 24 136 160
V–60.0 806 768 3 6 29
H–60.123 1312 1024 16 96 176
V–75.029 800 768 1 3 28
H+/–68.681 1456 1152 32 128 144
V+/–75.062 915 870 3 3 39
H+/–61.805 1504 1152 18 134 200
V+/–65.96 937 900 2 4 31
H + 63.981 1688 1280 48 112 248
V + 60.02 1066 1024 1 3 38
H + 79.976 1688 1280 16 144 248
V + 75.035 1066 1024 1 3 38
Mode H/V
Sort
1
2
3
4
5
6
7
8
9
10
11
12
13
25.175
28.321
25.175
31.5
40.0
49.5
57.283
65.0
78.75
100.0
92.978
108.0
135.0
640x350
70Hz
640x480
60Hz
640x480
75Hz
720x400
70Hz
800x600
60Hz
800x600
75Hz
832x624
75Hz
1024x768
60Hz
1024x768
75Hz
1152x870
75Hz
1152x900
65Hz
1280x1024
60Hz
1280x1024
75Hz
Sync
Polarity Frequency
Dot
Clock Total Period
(E)
Video Active Time
(A)
Sync Duration
(D)
Back Porch
(F)
Front Porch
(C)
Resolution

- 5 -
FRONT VIEW
Front Control Panel
REAR VIEW
OPERATING INSTRUCTIONS
MENU
AUTO
SELECT
See Front Control Panel
Power Connect
213 46 5
1. Power ON/OFF Button
Use this button to turn the monitor on or off.
2. Power Indicator
This indicator lights up green when the monitor
operates normally. If the display is in DPM(Energy
Saving)mode, this indicator color change to amber.
3. MENU Button
Use these buttons to enter or exit the On Screen Display.
4. ▼▲◀▶ Button
Use these buttons to choose or adjust items in the On
Screen Display.
5. SELECT Button
Use this button to enter a selection in the On Screen Display.
Use this button to scanning auto adjust.
6. AUTO Button
Use this button to enter a selection in the on screen
display.
D-Sub Signal
Connect
* AUTO adjustment function
TO the AUTO button before
using OSD menu. This button is
for the automatic adjustment of the screen position, clock
and phase.
Note: Some signal from some graphics boards may not
function properly. If the results are unsatisfactory, adjust
your monitor’s Position, Clock and Phase manually.
PROCESSING
AUTO CONFIGURATION

Power Board
Main Board
LCD Module
Control Board
CN1
CN3
J702 J705 J710
CN2
J1
- 6 -
WIRING DIAGRAM
(AU Module)
Connector Ass’y P/N:
6631T12002L
Connector Ass’y P/N:
6631T25008V
Connector Ass’y P/N:
6631T11012W
Connector Ass’y P/N:
6631T12002M

- 7 -
WIRING DIAGRAM
(Hydis Module)
Power Board
Main Board
LCD Module
Control Board
CN1
CN3
J702 J705 J710
CN2
J1
Connector Ass’y P/N:
6631T12002L
Connector Ass’y P/N:
6631T25008V
Connector Ass’y P/N:
6631T11012W
Connector Ass’y P/N:
6631T12002M

- 8 -
B
)
R,G,B
differential
LVDS
(Low Voltage
Differential Signaling)
Data 8 Bit
Address
5V
AVDD 3.3V
DVDD 3.3V
5V
AC Inpu t
AVDD 2.5V
DVDD 2.5V
AVDD3.3V
DVDD3.3V AVDD2.5V
DVDD2.5V
5V 5V
12V
R,G,B, H/V Sync
..
BLOCK DIAGRAM

- 9 -
DESCRIPTION OF BLOCK DIAGRAM
1. Video Controller Part & Display Data Transmitter Part.
This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the
digital video signal using a pixel clock.
The pixel clock for each mode is generated by the PLL.
The range of the pixel clock is from 25MHz to 135MHz.
This part consists of the Scaler, Flash-ROM IC which stores program data, Reset IC.
The Scaler gets the video signal converted analog to digital, interpolates input to 1280 x 1024 resolution signal and
outputs 8-bit R, G, B signal to transmitter.
Especially pre-amp / ADC / Video controller/ Transmitter are merged to one chip ‘Gm2121’by Genesis.
This part transmit digital signal from the Scaler to the receiver of module.
2. Power Part
This part consists of the one 3.3V and one 2.5 regulators to convert power which is provided 5V in LIPS Board.
5V is provided for LCD Panel.
Also, 5V is converted 3.3V and 2.5V by regulator. Converted power is provided for IC in the main board.

- 10 -
EMI
COMPONENTS
LINE
100 ~ 240V
INPUT RECTIFIER
AND FILTER ENERGY TRANSFER OUTPUT RECTIFIER AND FILTER
12V
5V
GND
SIGNAL
COLLENTI
ON
PHOTO-
COUPLER
ISOLATION
PWM
CONTROL
CIRCUIT
HVDC 100KHz
PRIMARY SECONDARY
50 ~ 60Hz
INVERTER CIRCUIT
12V High Voltage output
Operation description_LIPS
LIPS Board Block Diagram
1. EMI components.
This part contains of EMI components to comply with global marketing EMI standards like FCC, VCCI CISPR, the
circuit included a line-filter, across line capacitor and of course the primary protection fuse.
2. Input rectifier and filter.
This part function is for transfer the input AC voltage to a DC voltage through a bridge rectifier and a bulk capacitor.
3. Energy Transfer.
This part function is transfer the primary energy to secondary through a power transformer.
4. Output rectifier and filter.
This part function is to make a pulse width modulation control and to provide the driver signal to power switch, to
adjust the duty cycle during different AC input and output loading condition to achive the dc output stablize, and also
the over power protection is also monitor by this part.
5. Photo-Coupler isolation.
This part function is to feed back the dc output changing status through a photo transistor to primary controller to
achieve the stabilized dc output voltage.
6. Signal collection.
This part function is to collect the any change from the dc output and feed back to the primary through photo
transistor.
7. Inverter
The inverter converts from DC12V to AC 700V and operate back-light lamp of module.

- 11 -
ADJUSTMENT
All adjustment are thoroughly checked and corrected
when the monitor leaves the factory, but sometimes
several minor adjustment may be required.
Adjustment should be following procedure and after
warming up for a minimum of 10 minutes.
•Alignment appliances and tools.
- IBM compatible PC
- Programmable Signal Generator.
(eg. VG-819 made by Astrodesign Co.)
- E(E)PROM with each mode data saved.
1. Adjustment Start
1) Display any pattern at any Mode.
2) Run alignment program for LB700G on the IBM
compatible PC.
3) Select EEPROM →Init →Initialize command and
Enter.
4) This will make all data to default state.
5) Select COLOR→PRESET START command
and Enter.
2. Adjustment for White Balance
1) Display Black pattern at SXGA/60Hz.
2) Select COLOR → BIAS CALIBRATION command
and Enter.
3) No attempt to manually adjust, BIAS data is auto-
matically adjusted and saved to the EEPROM.
4) Display Full White pattern at SXGA/60Hz.
5) Select GAIN CALIBRATION command and Enter.
6) 6500K and 9300K are automatically adjusted and
saved to the EEPROM.
7) Select COLOR → PRESET END command and
Enter.
3. Adjustment for EDID
1) Use this procedure only when there is some
probelm on EDID data.
2) Connect the D-sub cable.
3) Select EDID →Write EDID[A0] command and
Enter.
220
IBM
Compatible PC
Video Signal
Generator
PARALLEL PORT
Power inlet (required)
Power LED
ST Switch
Power Select Switch
(110V/220V)
Control Line
Not used
RS232C
PARALLEL
V-SYNC POWER
ST
VGS MONITOR
E
E
V-Sync On/Off Switch
(Switch must be ON.)
F
F
A
A
B
B
C
C
1510
5
569
1
1
1
14
13
25
6
5V
5V
5V
4.7K
4.7K
4.7K
74LS06
74LS06
OFF ON
OFF
ON
11
Figure 1. Cable Connection

- 12 -
TROUBLESHOOTING GUIDE
1. NO POWER
TROUBLE IN
LIPS (POWER)
CHECK J702
5V VOLTAGE
(5V) ?
NO
NO POWER
(POWER INDICATOR OFF)
TROUBLE
SOMEWHERE ELSE
TROUBLE IN
LIPS (POWER)
CHECK J702
INPUT VOLTAGE
(12V) ?
NO
TROUBLE IN
U203 or X201
NO
YES
YES
YES
CHECK
U203’s PIN 103.
IS THIS PIN
OSCILLATED?

- 13 -
2. NO RASTER
TROUBLE IN
U804
CHECK
J705 PIN 1, 2, 3
(5V) ?
NO
NO RASTER
TROUBLE IN
LIPS
CHECK
J702 PIN 5, 6
(5V) ?
NO
TROUBLE IN
U801
CHECK
U801
(3.3V)?
NO
TROUBLE IN
U203
CHECK
U203(GM2121) ? NO
YES
YES
YES
YES
TROUBLE IN
LCD MODULE

- 14 -
3. NO CLOCK (CLOCK GENERATOR)
NO DOT CLOCK
TROUBLE IN
X201
CHECK
X201 20MHz ? NO
YES
4. TROUBLE IN DPM
TROUBLE IN DPM
TROUBLE IN PC
CHECK PC
PC IS NOT GOING
INTO DPM OFF MODE
NO
TROUBLE IN
X201
NO
TROUBLE IN
SIGNAL CABLE
NO
YES
YES
YES
CHECK
U203 PIN 102
WAVEFORM
(20MHz) ?
CHECK
R713, R715
(SYNC) ?
CHECK
U203 PIN 34
(0V) ?

PRINTED CIRCUIT BOARD
- 15 -
1. MAIN BOARD (Component Side)
J704
ZD718
R713 U270
C717
R717 R714
MODEL:LB700G
P/N :6870T562A12
DATE :2002.09.27
ZD719
R741
R716
R715
C718
R211
R213
U202
R233
R234
R705 R703
R704 ZD720
A
D701
R749 R750
R711
R712
R740
R235 R236
R262
R266
A
R261 R232
R214
R216
C715
C714
R752
R751
R230
R221
R204
R203
C206
C205
R748
C725
D703D704
R210
D702
R702
D710
R733R734
D709
R277
C703
R276 R267
R268 R269 R270 R272 R271
R273 R274
ZD711
U702
R275
ZD703
ZD704
R265
R263
R258
R229 R222
30
C203
R255
C724
C723
R747
R745
C219
C213 R207 R208 R215 R250 R218
C214
C211 R227
R228
R225
R226
R224
C280
C210
C281
C204
C221
R223C282
R212 R238
C239
510
U201
25
C722 C721
R744 R743
5
160
R209
150
140 130
120
J710
C720
C209
R742
10
110
R202
15
R264
R259
R243
R242
20
R201 R251 R241 R244 R245 R240 R253
C217
J705
20
100
C201
C232
Q202
X201
R248
R257
R256
R254
R252
R249
R239
R247 R246
30
R220
90
C202
C218
C215
R280
C806
C241 C237 C242
40
C212
50
60
C231
C235
70
C238
80
U203
C208
C224 C220 C244 C216
C805
C807
C804
C808
C234
C704
C706
R701
R205
C810
C811
C812
C813
C802
C803
L823
U804
C818
C860
R219
L803
C809
L804 U801
L802
L801
C819
R809
R206
C207
C840
U803
C801
C817
R821
R217
R231
J702
L811
2. MAIN BOARD (Solder Side)
C905
C911
C906
C907
C225
C236
C240
C901
C902
C908
C904
C903
C910
C909
R810
R830
R746
R811
R814
R825
R812 R813 R815
R817
R819 R818 R820
R816

- 16 -
3. ADAPTER B OARD (Component Side)
4. ADAPTER B OARD (Solder Side)
To apply the AU Module.

- 17 -
5. ADAPTER B OARD (Component Side)
6. ADAPTER B OARD (Solder Side)
To apply the HYDIS Module.

- 18 -
EXPLODED VIEW
1
2
4
7
3
10
5
6
9
8
11
c
b
a

- 19 -
EXPLODED VIEW PARTS LIST
Ref. No.
1
2
3
4
5
6
7
8
9
10
11
a
b
c
Part No.
3091TKL053B
6304FHD005A
6304FAU005A
3809TKL035B
3043TKK091E
4814TKK231A
4951TKS094D
4951TKS094B
6634B00055B
6634B00055A
3313TL7008A
6631T11012W
6871TST321A
6850TD9001A
1SZZTMF008A
332-113S
332-105G
Description
CABINET ASSEMBLY, LB700G BRAND 3090TKL053A HF350U
LCD(LIQUID CRYSTAL DISPLAY) HT17E12-100 HYUNDAI TFT COLOR LVDS TYPE SSM
LCD(LIQUID CRYSTAL DISPLAY) M170EN05 AU TFT COLOR 17.0" SXGA LVDS SMM
BACK COVER ASSEMBLY, LB700G 3808TKL039A HF350U
TILT SWIVEL ASSEMBLYLM805L -HIPS NO USB
SHIELD INVERTER LAMP WIRE,LB700K
METAL ASSEMBLY, FRAME LB700G (HYUNDAI) (LB700G-GD)
METAL ASSEMBLY, FRAME LB700G(AU) (LB700G-GU)
ADAPTER,AC-DC, PWI1504FG-A 5V/12A 1A/1.2A LIPS FOR HYDIS LB700K (LB700G-GD)
ADAPTER,AC-DC, PWI1504FG 5V/12A 1A/1.2A POWERNET LIPS FOR LB700K (LB700G-GU)
MAIN TOTAL ASSEMBLY LB700G.ASRDG BRAND CL-43
CONNECTOR ASSEMBLY, 30P H-H 200MM UL20276 LG708G
PWB(PCB) ASSEMBLY,SUB, LB800K CONTROL TOTAL BRAND CL-42
CABLE,D-SUB UL 2990-9C(7.5) DT 1870MM GRAY(85964) BRAND DM
SCREW,DRAWING, D3.0 L6.0 MSWR/FZMY
SCREW,DRAWING, D3.0 L12.0 MSWR/BK
SCREW,DRAWING, PVS+4*10(MSWR/BK)

- 20 -
DATE: 2002. 10. 16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C201 0CC120CK41A 12PF 1608 50V 5% R/TP NP0
C202 0CC120CK41A 12PF 1608 50V 5% R/TP NP0
C203 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C204 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C205 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C206 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C207 0CH8106F611 10UF 16V M 85STD(CYL) R/TP
C208 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C209 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C210 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C211 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C212 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C213 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C214 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C215 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C216 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C217 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C218 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C219 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C220 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C221 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C224 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C225 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
C231 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C232 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C234 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C235 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C236 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
C237 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C238 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C239 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C240 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
C241 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C242 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C244 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C280 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C281 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C282 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C703 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C704 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C706 0CC221CK41A 220PF 1608 50V 5% R/TP NP0
C714 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C715 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C717 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C718 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C720 0CC471CK41A 470PF 1608 50V 5% R/TP NP0
C721 0CC471CK41A 470PF 1608 50V 5% R/TP NP0
C722 0CC471CK41A 470PF 1608 50V 5% R/TP NP0
C723 0CC471CK41A 470PF 1608 50V 5% R/TP NP0
C724 0CC471CK41A 470PF 1608 50V 5% R/TP NP0
C725 0CC471CK41A 470PF 1608 50V 5% R/TP NP0
C801 0CE107EF638 100UF KMG 16V M FM5 TP 5
DATE: 2002. 10. 16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C802 0CH8107D611 100UF 10V 20% 85STD (CYL) R/TP
C803 0CH8107D611 100UF 10V 20% 85STD (CYL) R/TP
C804 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C805 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C806 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C807 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C808 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C809 0CH8476F611 47UF 16V 20% 85STD (CYL) R/TP
C810 0CH8476F611 47UF 16V 20% 85STD (CYL) R/TP
C811 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C812 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C813 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C817 0CH8107F611 100UF 16V M 85STD(CYL) R/TP
C818 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C819 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P
C840 0CE477EH618 470UF KMG 25V M FL TP 5
C860 0CK105CD56A 1UF 1608 10V 10% R/TP X7R
C911 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
D701 0DS226009AA KDS226 TP KEC SOT-23 80V 300M
D702 0DS226009AA KDS226 TP KEC SOT-23 80V 300M
D703 0DS226009AA KDS226 TP KEC SOT-23 80V 300M
D704 0DS226009AA KDS226 TP KEC SOT-23 80V 300M
D709 0DS301109AA MMBD301LT1 TP MOTOROLA SOT23 3
D710 0DS301109AA MMBD301LT1 TP MOTOROLA SOT23 3
ZD703 0DZ560009DA UDZ S 5.6B TP ROHM-K SOD323 20
ZD704 0DZ560009DA UDZ S 5.6B TP ROHM-K SOD323 20
ZD711 0DZ560009DA UDZ S 5.6B TP ROHM-K SOD323 20
ZD718 0DZ560009DA UDZ S 5.6B TP ROHM-K SOD323 20
ZD719 0DZ560009DA UDZ S 5.6B TP ROHM-K SOD323 20
ZD720 0DZ560009DA UDZ S 5.6B TP ROHM-K SOD323 20
U201 0IZZTSZ213A ATMEL/STM 32PIN ST OTP LB700G
U202 0IMMRSS040C S524A60X51(SCT0) SAMSUNG ELECT
U203 0IPRPGN004A GM2121 GENESIS 160P,PQFP TRAY
U270 0ISTLFA058A 74F14SCX FAIRCHILD 14P,SOIC R/
U702 0ISS524202B S524A40X21(SCT0) SAMSUNG ELECT
U801 0IRH033200A BA033FP-E2 MOLD-3 TP REGULATOR
U803 0IPMGON007A NCP1117ST25T3 ON SEMI SOT223 R
U804 0TFVI80023A VISHAY SI3865DV R/TP TSOP-6 8V
L801 6210TCE001G HH-1M3216-501 CERATEC 3216MM R
L802 6210TCE001G HH-1M3216-501 CERATEC 3216MM R
L803 6210TCE001G HH-1M3216-501 CERATEC 3216MM R
L804 6210TCE001G HH-1M3216-501 CERATEC 3216MM R
L811 6210TCE001G HH-1M3216-501 CERATEC 3216MM R
L823 6210TCE001G HH-1M3216-501 CERATEC 3216MM R
REPLACEMENT PARTS LIST
CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS,
READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL.
* NOTE : S SAFETY Mark
AL ALTERNATIVE PARTS
MAIN BOARD
CAPACITORS
DIODEs
ICs
COILs & COREs