Lg Mw 71py10 User manual

PLASMA MONITOR

SERVICE MANUAL

CAUTION

BEFORE SERVICING THE CHASSIS,

READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : RF-04FA

MODEL : MW-71PY10

CANADA : http//biz.lgservice.com

USA : http//www.lgservice.com

: http//lgservice.com/techsup.html

http://www.wjel.net

- 2 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in

the Schematic Diagram and Replacement Parts List.

It is essential that these special safety parts should be replaced with the same components as recommended in this manual to

prevent X-RADIATION, Shock, Fire, or other Hazards.

Do not modify the original design without permission of manufacturer.

General Guidance

An lsolation Transformer should always be used during

the servicing of a receiver whose chassis is not isolated from

the AC power line. Use a transformer of adequate power rating

as this protects the technician from accidents resulting in

personal injury from electrical shocks.

It will also protect the receiver and it's components from being

damaged by accidental shorts of the circuitary that may be

inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this monitor is blown, replace

it with the specified.

When replacing a high wattage resistor (Oxide Metal Film

Resistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Due to high vacuum and large surface area of picture tube,

extreme care should be used in handling the Picture Tube.

Do not lift the Picture tube by it's Neck.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source,

connect an electrical jumper across the two AC plug prongs.

Place the AC switch in the on positioin, connect one lead of

ohm-meter to the AC plug prongs tied together and touch other

ohm-meter lead in turn to each exposed metallic parts such as

antenna terminals, phone jacks, etc.

If the exposed metallic part has a return path to the chassis, the

measured resistance should be between 1MΩ and 5.2MΩ.

When the exposed metal has no return path to the chassis the

reading must be infinite.

An other abnormality exists that must be corrected before the

receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check.

Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor

between a known good earth ground (Water Pipe, Conduit, etc.)

and the exposed metallic parts.

Measure the AC voltage across the resistor using AC

voltmeter with 1000 ohms/volt or more sensitivity.

Reverse plug the AC cord into the AC outlet and repeat AC

voltage measurements for each esposed metallic part. Any

voltage measured must not exceed 0.75 volt RMS which is

corresponds to 0.5mA.

In case any measurement is out of the limits sepcified, there is

possibility of shock hazard and the set must be checked and

repaired before it is returned to the customer.

Leakage Current Hot Check circuit

CANADA: LG Electronics Canada, Inc. 550 Matheson

Boulevard East Mississauga, Ontario L4Z 4G3

USA : LG Customer Interactive Center

P.O.Box 240007, 201 James Record Road Huntsville,

AL 35824

Digital TV Hotline 1-800-243-0000

1.5 Kohm/10W

To Instrument's

exposed

METALLIC PARTS

Good Earth Ground

such as WATER PIPE,

CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF

http://www.wjel.net

- 3 -

DESCRIPTION OF CONTROLS...........................................4

SPECIFICATIONS.................................................................7

ADJUSTMENT INSTRUCTIONS ..........................................8

BLOCK DIAGRAM...............................................................13

EXPLODED VIEW...............................................................14

EXPLODED VIEW PARTS LIST.........................................15

REPLACEMENT PARTS LIST............................................16

SCHEMATIC DIAGRAM..........................................................

PRINTED CIRCUIT BOARD ...................................................

TABLE OF CONTENTS

http://www.wjel.net

- 4 -

Controls

INPUT SELECT

MENU

VOL

R

TruSurround XTruSurround XT

Front Panel Controls

MENU Button

INPUT SELECT Button

VOLUME (FF,GG) Buttons

EE, DDButtons

INDEX

Switches

LED Display

on or off.

Remote

Control

Sensor

Power Indicator

Illuminates orange in standby

mode, Illuminates green when

the monitor is turned on.

(If the power indicator is red,

contact your service center.)

Sub power Button

DESCRIPTION OF CONTROLS

http://www.wjel.net

- 5 -

Connection Options

REMOTE

CONTROL

RS-232C INPUT

(CONTROL/SERVICE)

AC INPUT

DVI INPUT

AUDIO INPUT RGB INPUT

AUDIO

COMPONENT

R L

VIDEO

INPUT 1

INPUT 2 VIDEO

INPUT 2

VIDEO

INPUT 1

VIDEO

MONO

AUDIO

R L

S-VIDEO

VIDEO3 VIDEO4

HDMI

R

( )( )

( )

L

EXTERNAL SPEAKER

Back Connection Panel

EXTERNAL SPEAKER

(8 ohm output)

Connect to optional

external speaker(s).

* For further information,

refer to ‘Speaker &

Speaker Stand’ manual.

Audio/Video Input

Connect audio/video output from

an external device to these jacks.

Component Input (1,2)

Connect a component video/audio

device to these jacks.

EURO SCART SOCKET

Connect the euro scart of

the VCR to these sockets.

Remote Control Port

Connect your wired

remote control here.

S-Video Input

Connect S-Video out from

an S-VIDEO device to the

S-VIDEO input.

Power Cord Socket

This TV operates on an AC power. The voltage is indi-

cated on the Specifications page. Never attempt to oper-

ate the TV on DC power.

RS-232C INPUT

(CONTROL/SERVICE) PORT

Connect to the RS-232C port

on a PC.

HDMI

Connect a HDMI

signal to this jack.

DVI Input/Audio Input/RGB Input

Connect the monitor output connector

from a PC to the appropriate input port.

DESCRIPTION OF CONTROLS

http://www.wjel.net

- 6 -

-When using the remote control, aim it at the remote control sensor on the monitor.

- Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press

the key again as necessary.

Remote Control Key Functions

LIGHT

INPUT

MODE

PIP

MUTE SLEEP

VOL CH

WIN. SIZE

WIN. POSITION

SPLIT ZOOM

MENU

PIP INPUT ARC

EXIT

PLAY PAUSE STOP RECORD

VIDEO COM1 RGB

DVI

ENTER

HDMI

KEY LOCK INDEX

REW FF SKIP

POWER

DW

DASP

APC

COM2

LIGHT

Illuminates the remote control buttons.

INPUT

Selects: Video1-2-3-4, Component 1-2,

RGB-DTV (or RGB-PC),

DVI-DTV (or DVI-PC), HDMI input sources.

PIP

Selects the PIP mode.

NUMBER buttons

Dosen’t work for monitor mode.

APC

Adjusts the factory preset picture according

to the room.

MUTE

Switches the sound on or off.

VCR/DVD BUTTONS

Control some video cassette recorders or

DVD player ("RECORD" button is not avail-

able for DVD player).

SPLIT ZOOM

Enlarges the picture.

MODE

Selects the remote operating mode: MNT,

VCR, DVD, CABLE, HDSTB or AUDIO.

Select other operating modes, for the

remote to operate external devices.

POWER

Turns your monitor or any other pro-

grammed equipment on or off, depending

on mode.

DW

Selects the DW mode.

SLEEP

Sets the Sleep Timer.

XD

Switches the XD on or off.

DASP

To select the sound appropriate to your

viewing program character:

Flat,Music, Cinema,Sports, or User

THUMBSTICK

(Up/Down/Left/Right/ENTER)

Allows you to navigate the on-screen

menus and adjust the system settings to

your preference.

CHANNEL UP/DOWN

Selects available channels found with Auto

program. Dosen’t work for monitor mode.

EXIT

Clears all on-screen displays and returns to

monitor viewing from any menu.

ARC

Changes the picture format.

VOLUME UP/DOWN

Increases/decreases the sound level.

WIN.POSITION

Moves the sub picture.

MENU

Brings up the main menu to the screen.

WIN. SIZE

Adjusts the sub picture size.

PIP INPUT

Selects the input source for

the sub picture. VIDEO/COM1/COM2/RGB/DVI/HDMI

Selects: Video1-2-3-4, Component 1-2,

RGB-DTV (or RGB-PC), DVI-DTV (or DVI-

PC), HDMI input sources.

KEY LOCK

Switches the key lock on or off.

INDEX

Switches LED Display on or off.

DESCRIPTION OF CONTROLS

http://www.wjel.net

- 7 -

•The specifications shown above may change without notice for quality improvement.

MODELS

Width (inches / mm)

Height (inches / mm)

Depth (inches / mm)

Weight (pounds / kg)

Power requirement

Resolution

Color

Viewing Size (mm)

Operating Temperature Range

Operating Humidity Range

MW-71PY10

68.9 / 1750

38.7 / 982

3.9 / 98

183.6 / 83.3

AC110-240V ~ 50/60Hz

1920 x 1080 (Dot)

16,770,000 (256 steps of each R, G and B)

1512.26

32 ~ 104°F (0 ~ 40°C)

Less than 80%

SPECIFICATIONS

http://www.wjel.net

- 8 -

ADJUSTMENT INSTRUCTIONS

1. Application Object

These instructions apply to the RF-04FA(MN/MW-71PY10

Monitor) Chassis.

2. Specification

(1) Because this is not a hot chassis, it is not necessary to

use an isolation transformer. However, the use of isolation

transformer will help protect test equipment.

(2) Adjustment must be done in the correct order.

(3) The adjustment must be performed in the circumstance of

25±5°C of temperature and 65±10% of relative humidity.

(4) The input voltage of the receiver must keep 100~220V,

50/60Hz.

(5) The receiver must be operated for about 15 minutes prior

to the adjustment.

OAfter RGB Full white HEAT-RUN Mode, the receiver must

be returned to normal operation prior to adjustment.

OEnter into HEAT-RUN MODE

1) Press the POWER ON KEY on R/C for adjustment.

2) OSD display and screen display 100% full WHITE

PATTERN.

[Set is activated HEAT-RUN without a signal generator in

this mode.

[Single color pattern(RED/BLUE/GREEN) of HEAT-RUN

mode is used to test the PANEL.

Caution) If you turn on a still screen more than 20 minutes

(Especially digital pattern, cross hatch pattern), an

afterimage may be occur in the black level part of the

screen.

3. HDCP Download

3-1. LGIDS Setting Method

(1) Click on ‘setup’ to install in your directory.

(2) After installation has completed, check if the file shown on

(Fig. 4) has been created.

(3) Copy the KEY from source CD into the HDCP directory

which was installed just now.

(DVI_orderNo_2003_data)

(4) After running HDCP(application program) which is inside

the HDCP directory, setup the Communication.

Port : COM1(modification possible)

BaudRate : 115200

3-2. KEY Generation

(1) Click on ‘Key Generation (G)’.

(2) Input the quantity of keys to be generated.

ex) If 100 Keys are required, then just register 100 and

next time it will automatically get 101.

(3) Input file : When installing the program for the first time,

you must find the original KEY that you copied and open it.

It is crucial that you copy the original KEY into this

directory.

When you use Generation, the information is recorded in

Config.ini.

(Fig. 1)

(Fig. 2)

http://www.wjel.net

- 9 -

ADJUSTMENT INSTRUCTIONS

(4) Click on ‘Generation’ ———————————————(1)

If it is done correctly, you will see “Job is Success.”——(2)

Click on ‘close’——————————————————(3)

Check the Generation Data(Confirmation it’s possible

within HDCP\CreatedKeyFile)

(5) It is possible to check how many Generations are created

at this point.

(Fig. 4) shows that you have created 130 Generations and

you will start from 131 next time.

3-3. HDCP Download Method

(1) Input power of Stand-By 5V.

(Download must be executed only when the unit is in

Stand-by)

(2) The RS-232C(9PIN) must be connected to the COM1 on

the PC.

(3) If all the preparation is completed, click on ‘Download’.

(4) If abnormal state (Fig. 7) display then (3) execute.

(Fig. 3)

(Fig. 4)

(Fig. 5)

(Fig. 6) Normal State

(Fig. 7) Abnormal State

http://www.wjel.net

- 10 -

4. POWER PCB Assy Voltage

Adjustments (Va, Vs, 5V Vcc Voltage Adjustments)

4-1. Test Equipment :D.M.M. 1EA

4-2. Diagram for Measuring

Refer to (Fig 8).

4-3. Adjustment Method

(1) Va Adjustment

1) Connect + terminal of D.M.M to Va pin of P805, connect

- terminal to GND pin of P805.

2) Turn RV501, to adjust the Va voltage to match the value

marked on the label on the right/top of the panel.

(Deviation; ±0.5V)

(2) Vs Adjustment

1) Connect + terminal of D.M.M to Vs pin of P805, connect

– terminal to GND pin of P805.

2) Turn RV401, to adjust the Vs voltage to match the value

marked on the label on the right/top of the panel.

(Deviation; ±0.5V)

(3) 5V Voltage Adjustment

1) Connect + terminal of D.M.M to 5V Vcc pin of P804,

connect – terminal of D.M.M to GND pin of P804 on the

left PSU.

Turn RV601, to adjust the voltage value of D.M.M to be

5.3V. (Deviation; ±0.05V)

2) Connect + terminal of D.M.M to 5V Vcc pin of P804,

connect – terminal of D.M.M to GND pin of P804 on the

right PSU.

Turn RV601, to adjust the voltage value of D.M.M to be

5.3V. (Deviation; ±0.05V)

3) Connect + terminal of D.M.M to 5V Vcc pin of P804,

connect – terminal of D.M.M to GND pin of P804 on the

left PSU.

Turn RV601, to adjust the voltage value of D.M.M to be

5.6V. (Deviation; ±0.05V)

4) Connect + terminal of D.M.M to 5V Vcc pin of P804,

connect – terminal of D.M.M to GND pin of P804 on the

right PSU.

Turn RV601, to adjust the voltage value of D.M.M to be

5.6V. (Deviation; ±0.05V)

* Caution 1) Because there are two units in PSU, one of

them fixes to 5.3V voltage and then the other

adjusts to 5.3V voltage. After adjusting 5.3V

voltage with each other, one of them and the

other adjust to 5.6V voltage accordingly.

* Caution 2) Make small adjustments. Great differences

can cause the unit to shutdown.

5. DDC Data Input

5-1. Required Test Equipment

(1) A jig for adjusting PC, DDC (PC serial to D-sub

Connection equipment)

(2) S/W for writing DDC (EDID Data Write & Read)

(3) D-sub 15P Cable, DVI Cable, DVI to HDMI Connector

(HDMI EDID Down load)

5-2. Setting of Device

ADJUSTMENT INSTRUCTIONS

Each PCB assembly must be checked by Check JIG Set

before assembly. (Take special note of the Power PCB, which

can easily damage the PDP module)

(Fig. 8) Connection Diagram for measuring Power Adjustments

(Fig. 9)

http://www.wjel.net

- 11 -

ADJUSTMENT INSTRUCTIONS

5-3. Preparation for Adjustment

(1) Set devices as above and turn the PC and jig on.

(2) Put S/W for writing DDC (EDID data Write & Read) into

operation. (operated in DOS mode.)

5-4. Sequence of Adjustment

(1) DDC Data Input for Analog-RGB

1) Put the set on the table and turn the power on.

2) Connect PC Serial to D-sub 15P Cable of jig for DDC

adjustment to RGB terminal (D-Sub 15Pin).

3) Operate S/W for DDC record and select DDC

data(GT_HD_(8691).ana) for Analog RGB in Model

Menu.

4) Operate EDID Write command.

5) Operate EDID Read command and check whether

Check Sum is 86(1page), 91(2page).

6) If Check Sum is not 86(1page), 91(2page) repeat 3) ~

4).

7) If Check Sum is 86(1page), 91(2page), DDC data for

Analog-RGB input is completed.

(2) DDC Data input for Digital-DVI

1) Connect PC Serial to DVI Cable of jig for DDC

adjustment to DVI terminal (DVI Jack).

2) Operate S/W for DDC record and select DDC data

(GT_HD_(1D8F).dvi) for Digital-DVI in model menu.

3) Operate EDID Write command.

4) Operate EDID Read command and check whether

Check sum is 1D(1page), 8F(2page).

5) If Check sum is not 1D(1page), 8F(2page), repeat 3) ~

4).

6) If Check sum is 1D(1page), 8F(2page), DDC data for

Digital-DVI input is completed.

(3) DDC Data input for Digital-HDMI

1) Connect PC Serial to DVI to HDMI Cable of jig for DDC

adjustment to HDMI terminal (HDMI Jack).

2) Operate S/W for DDC record and select DDC data

(GT_HD_HDMI_(418F).dvi) for Digital-HDMI in model

menu.

3) Operate EDID Write command.

4) Operate EDID Read command and check whether

Check sum is 41(1page), 8F(2page).

5) If Check sum is not 41(1page), 8F(2page), repeat 3) ~

4).

6) If Check sum is 41(1page), 8F(2page), DDC data for

Digital-HDMI input is completed.

6. Adjustment of COLOR

6-1. Required Equipment

Color Analyzer (CA-100 or similar product)

Pattern Generator(VG-828)

6-2. Connection Diagram of Equipment for

Measuring Color

6-3. Adjustment Method of Auto RGB

Color Balance

(1) Input 16 Gray Scale Pattern(RGB output Level : 0.7Vp-p)

at the D-SUB input terminal using PC Pattern Generator.

(2) Press ADJ KEY on the S R/C.

(3) Press Vol. + KEY and operate To SET.

(4) Auto-RGB OK means completed adjustment.

6-4. Adjustment Method of Auto Video

Color Balance

(1) Input 16 Gray Scale Pattern(RGB output Level : 0.7Vp-p)

at the Video 1 input terminal using PC Pattern Generator.

(2) Press ADJ KEY twice on the S R/C.

(3) Press Vol. + KEY and operate To SET.

(4) Auto-RGB OK means completed adjustment.

6-5. Adjustment Method of Auto Video

Color Balance

(1) Input Pattern(Fig. 12) at the Component 1 input terminal

using PC Pattern Generator.

(2) Press ADJ KEY three time on the S R/C.

(3) Press Vol. + KEY and operate To SET.

(4) Auto-RGB OK means completed adjustment.

VG-828 CA-100

PDP SET

(Fig. 10)

(Fig. 11) Auto RGB Color Balance Test Pattern

http://www.wjel.net

- 12 -

6-6. Adjustment of White Balance

OOperate the Zero-calibration of the CA-100, then stick

sensor to PDP module surface when you adjust.

(1) Select white pattern of heat-run mode by pressing power

key on the Service Remote Control (S R/C) then allow to

heat run at least 15 minutes.

(2) Supply 216 Level 50% Window signal to RGB input using

Pattern Generator.

(3) Press ADJ KEY four time on the S R/C. (White Balance)

Select the adjustment mode(Red Gain or Blue Gain) using

D, Ekey on the S R/C and press VOL +, - keys to adjust

until color coordination matches below.

X; 0.280±0.005, Y; 0.290±0.005

Color Temperature; 10,000°K±500°K

(4) Exit adjustment mode using AKey.

ADJUSTMENT INSTRUCTIONS

(Fig. 12)

(Fig. 13)

http://www.wjel.net

- 13 -

BLOCK DIAGRAM

http://www.wjel.net

- 14 -

EXPLODED VIEW

301

305 306

307

101

102

200

212

211

210

209

203

204

213

600

214

215 208

207

206

205

202

201

580 400

401

520

501

540 590

591

530

560

561 310

302

304

570

303

550

http://www.wjel.net

- 15 -

EXPLODED VIEW PARTS LIST

101 5900V12003C FAN,G1225S12B2-FS DONGYANG DC AXIAL 12V 120MM 1250 PRM 3P 280MM HOUSING

102 4980V00B53A SUPPORTER,FAN EGI DN-71PY10

200 6348Q-J001G PDP,71 1920*1080 16-9 PDP71H10000.AKLGG

201 6871QDH076A PCB ASSEMBLY,DISPLAY YDRV ASSY 71X1 4LAYER(TOP)

202 6871QDH077A PCB ASSEMBLY,DISPLAY YDRV ASSY 71X1 4LAYER(BTM)

203 6871QCH047A PCB ASSEMBLY,DISPLAY CTRL ASSY 71 71X1 TMDS 8LAYER

204 6871QEH017A PCB ASSEMBLY,DISPLAY ETC PDP50X20000 TEMP. SENSOR B/D

205 6871QFH004A PCB ASSEMBLY,DISPLAY XRLB ASSY 71X1

206 6871QHH002A PCB ASSEMBLY,DISPLAY XRCB ASSY 71X1_XCLB

207 6871QHH003A PCB ASSEMBLY,DISPLAY XRCB ASSY 71X1_XCRB

208 6871QGH005A PCB ASSEMBLY,DISPLAY XRRB ASSY 71X1

209 6871QLH041A PCB ASSEMBLY,DISPLAY XRLT ASSY 71X1

210 6871QXH026A PCB ASSEMBLY,DISPLAY XRCT ASSY 71X1_XCLT

211 6871QXH027A PCB ASSEMBLY,DISPLAY XRCT ASSY 71X1_XCRT

212 6871QRH047A PCB ASSEMBLY,DISPLAY XRRT ASSY 71X1

213 6871QYH001B PCB ASSEMBLY,DISPLAY YSUS ASSY A31 LG PCB OBU

214 6871QZH037A PCB ASSEMBLY,DISPLAY ZSUS ASSY 71X1 4LAYER

215 6871QPH009A PCB ASSEMBLY,SUB DCDC ASSY 71H1 DC-DC B/D ASSY

301 3210V00267A FRAME,FRONT UPPER AL MN-71PY10 TOP

302 3210V00277A FRAME,FRONT SIDE AL MN-71PY10 LEFT

303 3210V00268A FRAME,FRONT LOWER AL MN-71PY10 BOTTOM

304 3210V00276A FRAME,FRONT SIDE AL MN-71PY10 RIGHT

305 5230V00024A FILTER(MECH),GLASS FILTER PDP 71 LG CHEMICAL GLASS LG LOGO

306 4980V00D29A SUPPORTER,FILTER AL TOP, BOTTOM MN-71PY10

307 4980V00D30A SUPPORTER,FILTER AL SIDE R,L MN-71PY10

310 5020V00995A BUTTON,CONTROL DU-50PY10 ABS, AF-303S 7KEY .

400 3809V00559B BACK COVER ASSEMBLY,MW-71PY10

401 3300V00392A PLATE,AV AL . COVER VSC TUNER DN-71PY10

501 3301V00040D PLATE ASSEMBLY,3300V00390A, 3300V00391D MW-71PY10 A/V PLATE

520 6871VMMT32A PCB ASSEMBLY,MAIN RF-04FA 71 DIGITAL VSC

530 6871VSMJ35A PCB ASSEMBLY,SUB RF04FA 71 ANALOG VSC

540 6871VSMZ98A PCB ASSEMBLY,SUB RF04FA SPK_TERMINAL 71

550 6871VSMG26A PCB ASSEMBLY,SUB RF04FA FAN CTRL

560 6871VSMZ99A PCB ASSEMBLY,SUB KEYBOARD RF03LA LOCAL KEY 71

561 4980V00B54A SUPPORTER,PCB AL CONTROL BOX MN-71PY10

570 6871VSMJ03A PCB ASSEMBLY,SUB RF04FA MN-71PY10 INDEX B/D

580 6709900007A POWER SUPPLY ASSEMBLY,71INCH PDP SANKEN RF-04FA NEW VER. 1H257WI-1

590 3141VSNJ23A CHASSIS ASSEMBLY,SUB RF04FA NOISE FILTER ASSY.

591 4980V00B63A SUPPORTER,MOUNTING EGI LINE FILTER & SPK TERMINAL MN-71PY10

600 6871VPMA93A PCB ASSEMBLY,POWER SMPS RF-04FA POWER INTERFACE MN-71PY10 ALL PDP

No. Part No. Description

http://www.wjel.net

- 16 -

REPLACEMENT PARTS LIST

LOCA. NO PART NO DESCRIPTION

IC2507

IC2508

IC2509

IC2601

IC2602

IC301

IC302

IC401

IC402

IC5001

IC5002

IC5003

IC5004

IC5005

IC5006

IC501

IC502

IC503

IC504

IC505

IC601

IC602

IC603

IC681

Q101

Q102

Q103

Q104

Q105

Q106

Q107

Q108

Q109

Q110

Q1101

Q1102

Q1103

Q1104

Q111

Q112

Q113

Q114

Q1201

Q1202

Q1203

Q1204

Q1205

0IPRPML001A

0IPMGNS032A

0IMCRFA010A

0IMCRRH001A

0IMMRNE002B

0IMCRET003A

0IMMRNE002B

0IMCRET003A

0IKE780500Q

0ISH092100B

0ISH122100B

0IMI623200B

0IDS162100B

0IMCRMN028B

0IMCRNL001B

0IKE704200J

0IMCRTI028C

0IPRPJR017A

0IMCRSH001A

0IPRPML001A

0IMCRFA010A

0IPMGNS032A

0TR387500AA

0TR830009BA

0TR387500AA

0TR104009AF

0TR387500AA

0TR150400BA

0TR387500AA

MIC39100 MICREL 3P SOT223

LM2611AMFX 5P/SOT23-5

KA7809R, FAIRCHILD 2P

BA033FP-E2 3P-SOP,TO252-3

UPD64083GF3BA-A 100

EL5261ISZ-T7 ELANTEC 8P

UPD64083GF3BA-A 100

EL5261ISZ-T7 8P

KIA7805API 3P TO-220

PQ09RD21 4SIP

PQ12RD21 4SIP

M62320FP 16P

DS1621V 8P

MSP4410K 80P

NSP-6241A 64P

KIA7042AF SOT-89 TP 4.2V

TAS5122DCARG4 56P

NJU26901E2 JRC 8P

PQ05DZ1U SHARP 5

MIC39100 MICREL 3P SOT223

KA7809R, FAIRCHILD 2P

LM2611AMFX 5P/SOT23-5

CHIP 2SC3875S(ALY) BK KEC

BSS83

CHIP 2SC3875S(ALY) BK KEC

CHIP KRC104S SOT-23 TP KEC

CHIP 2SC3875S(ALY) BK KEC

CHIP 2SA1504S(ASY) BK KEC

CHIP 2SC3875S(ALY) BK KEC

LOCA. NO PART NO DESCRIPTION

IC101

IC102

IC105

IC1102

IC1103

IC1104

IC1201

IC1202

IC1203

IC1204

IC1301

IC1303

IC1401

IC1411

IC1421

IC1451

IC1452

IC1471

IC1472

IC1501

IC1502

IC1601

IC1701

IC1801

IC1901

IC2001

IC201

IC202

IC2051

IC2101

IC2151

IC2201

IC2202

IC2203

IC2204

IC2206

IC221

IC2301

IC2401

IC2402

IC2451

IC2501

IC2502

IC2503

IC2504

IC2505

IC2506

0IMI623200B

0IMCRFA015A

0IMMRAL014B

0IPRPMX014A

0IFA742530B

0IDS232000A

0ISTLSG009A

0IMCRS5005A

0IMMRAL014B

0IPRPIS003A

0IFA742530B

0IPH741400E

0IMCRPH018A

0IPRPXI002A

0IPRPMX014A

0IIT323000E

0IPRPOK004A

0IMCRGN002D

0IPRPMX014A

0IMCRET003A

0IMMRHY033A

0IMCRGN002D

0IMMRHY033A

0IPRPGN017A

0IKE703300E

0IMMRAL025A

0IMI623200B

0IPRPMX014A

0IMMRHY020B

0ICTMLG018A

0IMCRRH001A

0IS5160000A

0IMCRRH001A

0IMCRSJ001A

0IPRPML001A

0IMCRSH001A

M62320FP 16P

KA7805R 2P D-PAK R/TP 500MA

AT24C02N-10SI-2.7 8P

MAX4572EAI-T 28P

74ACT253SC 16P

DS232AS 16P RS-232

M74HC123RM13TR 16P

SIL9993CTG100 100P

AT24C02N-10SI-2.7 8P

HA4314BCBZ96 14P

74ACT253SC 16P

74HC14D 14SOP

74LVC126AD 14P

X98017L128-3.3-Z 128P

MAX4572EAI-T 28P

VPC3230D C5 80P

ML87V2105TBZ03A OKI 100P

FLI2300BD-LF 208P

MAX4572EAI-T MAXIM 28P

EL5261ISZ-T7 ELANTEC 8P

HY57V643220C(L)T-6 HYNIX 86P

FLI2300BD-LF 208P

HY57V643220C(L)T-6 HYNIX 86P

GM1601H-LF-BD 416P

KIA7033AF 3P SOT-89

AT24C32AN-10SI-2.7 8PIN SOP TP 32K 3.3V

M62320FP 16P

MAX4572EAI-T 28P

HY5DU283222AQP-5 100P

LGDP4410 LG IC 176P

BA033FP-E2 ROHM 3P-SOP,TO252-3

SIL160CT100 SILICON IMAGE 100

BA033FP-E2 3P-SOP,TO252-3

SC1565IST-1.8 3P SOT223

MIC39100 MICREL 3P SOT223

PQ05DZ1U SHARP 5

IC

TRANSISTOR

RUN DATE : 2005.10.28

For Capacitor & Resistors, the

charactors at 2nd and 3rd digit

in the P/No. means as follows;

CC, CX, CK, CN : Ceramic

CQ : Polyestor

CE : Electrolytic

RD : Carbon Film

RS : Metal Oxide Film

RN : Metal Film

RF : Fusible

http://www.wjel.net

- 17 -

LOCA. NO PART NO DESCRIPTION

Q1206

Q1207

Q1208

Q1209

Q1210

Q1301

Q1302

Q1341

Q1501

Q1502

Q201

Q202

Q203

Q204

Q221

Q222

Q2501

Q2502

Q2503

Q301

Q302

Q303

Q304

Q305

Q306

Q307

Q308

Q309

Q310

Q311

Q312

Q401

Q402

Q403

Q404

Q405

Q406

Q407

Q408

Q409

Q410

Q411

Q412

D101

D102

D103

D104

D105

D106

D107

0TR104009AF

0TR387500AA

0TR150400BA

0TR387500AA

0TR830009BA

0TR387500AA

0TR830009BA

0TR387500AA

0TR150400BA

0TR387500AA

0TR150400BA

0TR387500AA

0TR150400BA

0TR387500AA

0TR150400BA

0TR387500AA

0TR150400BA

0TR387500AA

0TR150400BA

0TR387500AA

0TR150400BA

0TR387500AA

0TR150400BA

0TR387500AA

0TR150400BA

0DD226239AA

CHIP KRC104S SOT-23 TP KEC

CHIP 2SC3875S(ALY) BK KEC

CHIP 2SA1504S(ASY) BK KEC

CHIP 2SC3875S(ALY) BK KEC

BSS83

CHIP 2SC3875S(ALY) BK KEC

BSS83

CHIP 2SC3875S(ALY) BK KEC

CHIP 2SA1504S(ASY) BK KEC

CHIP 2SC3875S(ALY) BK KEC

CHIP 2SA1504S(ASY) BK KEC

CHIP 2SC3875S(ALY) BK KEC

CHIP 2SA1504S(ASY) BK KEC

CHIP 2SC3875S(ALY) BK KEC

CHIP 2SA1504S(ASY) BK KEC

CHIP 2SC3875S(ALY) BK KEC

CHIP 2SA1504S(ASY) BK KEC

CHIP 2SC3875S(ALY) BK KEC

CHIP 2SA1504S(ASY) BK KEC

CHIP 2SC3875S(ALY) BK KEC

CHIP 2SA1504S(ASY) BK KEC

CHIP 2SC3875S(ALY) BK KEC

CHIP 2SA1504S(ASY) BK KEC

CHIP 2SC3875S(ALY) BK KEC

CHIP 2SA1504S(ASY) BK KEC

KDS226 TP KEC

LOCA. NO PART NO DESCRIPTION

D108

D109

D110

D1101

D1102

D1103

D1104

D1105

D1106

D1107

D111

D1118

D1119

D112

D1120

D1121

D1122

D1123

D1124

D113

D114

D115

D116

D117

D118

D119

D1301

D2502

D2503

D2504

D2505

D2506

D2507

D2508

D2509

D2510

D2601

D2602

D5001

D601

D602

D603

D681

D8201

D8202

IC103

IC104

L2501

L2503

L2506

L2510

LED301

0DD226239AA

0DD184009AA

0DD226239AA

0DD184009AA

0DD226239AA

0DR340009AA

0DD226239AA

0DD100009AM

0DD226239AA

0DR340009AA

0DR360000BA

6301V00003A

0DL233309AC

KDS226 TP KEC

KDS184 TP KEC - 85V - 300MA

KDS226 TP KEC

KDS184 TP KEC - 85V - 300MA

KDS226 TP KEC

MBRS340 40V 3A 80A .SEC

KDS226 TP KEC

EU1ZV(1) 200V 0.25A 15A 0.4US

KDS226 TP KEC

MBRS340 40V 3A 80A .SEC

FMB-36M FM80 18W 0.62V

LED ASSEMBLY,UEX-LD-048

LED,SAM2333

REPLACEMENT PARTS LIST

DIODE

http://www.wjel.net

- 18 -

LOCA. NO PART NO DESCRIPTION

LED401

LED601

LED602

LED603

LED604

ZD101

ZD102

ZD1105

ZD1111

ZD1112

ZD1113

ZD1114

ZD501

C1122

C1124

C1138

C115

C118

C1207

C121

C1212

C1217

C1218

C1223

C1226

C1227

C1251

C1252

C1253

C1254

C1255

C1256

C1301

C1308

C1313

C1315

C1318

C1324

C1326

C1344

C1405

C1415

C1425

C1452

C1461

C1473

C1502

C1522

C1537

C1548

0DL233309AC

0DZRM00178A

0DR050008AA

0DZ820009AH

0CE476SF6DC

0CE107SF6DC

0CE477VF6DC

0CE475WJ6DC

0CE107SF6DC

0CE475WJ6DC

0CE106SF6DC

0CE105SK6DC

0CE106SF6DC

0CE105SK6DC

0CE476SF6DC

0CE105SK6DC

0CE226VF6DC

0CE106SF6DC

0CE226VF6DC

0CE107SF6DC

0CE226VF6DC

0CE476SF6DC

0CE106SF6DC

0CE226VF6DC

0CE107SF6DC

0CE106SF6DC

0CE476SF6DC

0CE107SF6DC

LED,SAM2333

ZENERS,UDZS TE-17 5.1B

SD05.TC SOD323 5V 5A 15A

ZENERS,MTZJ8.2B

47UF MVG 16V 20% SMD R/TP

100UF MVG 16V 20% SMD R/TP

470UF MV 16V 20% R/TP(SMD) SMD

4.7UF MVK 35V 20% R/TP(SMD) SMD

100UF MVG 16V 20% SMD R/TP

4.7UF MVK 35V 20% R/TP(SMD) SMD

10UF MVG 16V 20% R/TP(SMD) SMD

1UF MVG 50V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

1UF MVG 50V 20% SMD R/TP

47UF MVG 16V 20% SMD R/TP

1UF MVG 50V 20% SMD R/TP

22UF MV 16V 20% R/TP(SMD) SMD

10UF MVG 16V 20% R/TP(SMD) SMD

22UF MV 16V 20% R/TP(SMD) SMD

100UF MVG 16V 20% SMD R/TP

22UF MV 16V 20% R/TP(SMD) SMD

47UF MVG 16V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

22UF MV 16V 20% R/TP(SMD) SMD

100UF MVG 16V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

47UF MVG 16V 20% SMD R/TP

100UF MVG 16V 20% SMD R/TP

LOCA. NO PART NO DESCRIPTION

C1550

C1607

C1616

C1618

C1621

C1623

C1629

C1632

C1633

C1707

C1716

C1718

C1721

C1723

C1729

C1732

C1733

C1808

C1908

C202

C2021

C203

C2033

C2036

C2039

C204

C2042

C2045

C2048

C205

C206

C207

C208

C209

C211

C2121

C2133

C2136

C2139

C214

C2142

C2145

C2148

C216

C217

C218

C219

C2204

C222

C223

C224

C225

0CK105DF64A

0CE107SF6DC

0CE106SF6DC

0CE107SF6DC

0CE106SF6DC

0CE107SF6DC

0CE106SF6DC

0CK684DF56A

0CE107SF6DC

0CE106SF6DC

0CE107SF6DC

0CE106SF6DC

0CE107SF6DC

0CE106SF6DC

0CK684DF56A

0CE226VF6DC

0CE107SF6DC

0CE105SK6DC

0CE476SF6DC

0CE226VF6DC

0CE476SF6DC

0CE226VF6DC

0CE106SF6DC

0CE476SF6DC

0CE106SF6DC

0CE105SK6DC

0CE226VF6DC

0CE107SF6DC

0CE226VF6DC

0CE106SF6DC

0CE476SF6DC

0CE335SK6DC

0CE107SF6DC

0CE476SF6DC

1UF 2012 16V 20% F(Y5V) R/TP

100UF MVG 16V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

100UF MVG 16V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

100UF MVG 16V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

0.68UF 2012 16V 10% R/TP X7R

100UF MVG 16V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

100UF MVG 16V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

100UF MVG 16V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

0.68UF 2012 16V 10% R/TP X7R

22UF MV 16V 20% R/TP(SMD) SMD

100UF MVG 16V 20% SMD R/TP

1UF MVG 50V 20% SMD R/TP

47UF MVG 16V 20% SMD R/TP

22UF MV 16V 20% R/TP(SMD) SMD

47UF MVG 16V 20% SMD R/TP

22UF MV 16V 20% R/TP(SMD) SMD

10UF MVG 16V 20% R/TP(SMD) SMD

47UF MVG 16V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

1UF MVG 50V 20% SMD R/TP

22UF MV 16V 20% R/TP(SMD) SMD

100UF MVG 16V 20% SMD R/TP

22UF MV 16V 20% R/TP(SMD) SMD

10UF MVG 16V 20% R/TP(SMD) SMD

47UF MVG 16V 20% SMD R/TP

3.3UF MVG 50V 20% SMD R/TP

100UF MVG 16V 20% SMD R/TP

47UF MVG 16V 20% SMD R/TP

REPLACEMENT PARTS LIST

CAPACITOR

http://www.wjel.net

- 19 -

LOCA. NO PART NO DESCRIPTION

C226

C2261

C227

C228

C229

C230

C231

C232

C233

C235

C237

C2417

C2424

C2452

C2456

C2458

C2460

C2471

C2474

C2477

C2501

C2506

C2507

C2512

C2515

C2516

C2521

C2522

C2525

C2526

C2531

C2536

C2539

C2542

C2544

C2547

C2550

C2553

C2554

C2557

C2558

C2561

C2562

C2565

C2566

C2569

C2572

C2573

C2576

C2579

C2580

0CE476SF6DC

0CE107SF6DC

0CE476SF6DC

0CE107SF6DC

0CE106SF6DC

0CE476SF6DC

0CE107SF6DC

0CE226VF6DC

0CE477SF6DC

0CE227VF6DC

0CE477SF6DC

0CE227VF6DC

0CE477SF6DC

0CE227VF6DC

0CE477SF6DC

0CE476SF6DC

0CE477SF6DC

0CE476SF6DC

0CE477SF6DC

0CK106EF56A

0CE476SF6DC

0CE477SF6DC

0CE476SF6DC

0CE477SF6DC

0CE227VF6DC

0CE476SF6DC

0CE107SF6DC

47UF MVG 16V 20% SMD R/TP

100UF MVG 16V 20% SMD R/TP

47UF MVG 16V 20% SMD R/TP

100UF MVG 16V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

47UF MVG 16V 20% SMD R/TP

100UF MVG 16V 20% SMD R/TP

22UF MV 16V 20% R/TP(SMD) SMD

470UF MVG 16V 20% R/TP(SMD) SMD

220UF MV 16V 20% R/TP(SMD) SMD

470UF MVG 16V 20% R/TP(SMD) SMD

220UF MV 16V 20% R/TP(SMD) SMD

470UF MVG 16V 20% R/TP(SMD) SMD

220UF MV 16V 20% R/TP(SMD) SMD

470UF MVG 16V 20% R/TP(SMD) SMD

47UF MVG 16V 20% SMD R/TP

470UF MVG 16V 20% R/TP(SMD) SMD

47UF MVG 16V 20% SMD R/TP

470UF MVG 16V 20% R/TP(SMD) SMD

10UF 3216 16V 10% X7R R/TP

47UF MVG 16V 20% SMD R/TP

470UF MVG 16V 20% R/TP(SMD) SMD

47UF MVG 16V 20% SMD R/TP

470UF MVG 16V 20% R/TP(SMD) SMD

220UF MV 16V 20% R/TP(SMD) SMD

47UF MVG 16V 20% SMD R/TP

100UF MVG 16V 20% SMD R/TP

LOCA. NO PART NO DESCRIPTION

C2581

C2582

C2585

C2589

C2592

C2593

C2601

C2604

C2607

C2610

C2613

C2616

C2619

C2620

C2623

C2626

C2629

C2632

C2635

C302

C308

C314

C317

C329

C334

C339

C341

C349

C351

C402

C408

C414

C417

C429

C434

C439

C441

C449

C451

C5007

C5009

C501

C5016

C5017

C5018

C5019

C5023

C506

0CK105DF64A

0CE226VF6DC

0CE227VF6DC

0CE107SF6DC

0CK105DF64A

0CE477SF6DC

0CK106EF56A

0CE476SF6DC

0CK106EF56A

0CE476SF6DC

0CK106EF56A

0CE476SF6DC

0CE477SF6DC

0CE476SF6DC

0CK106EF56A

0CE476SF6DC

0CE106SF6DC

0CK473CH56A

0CE106SF6DC

0CE105SK6DC

0CE106SF6DC

0CE476SF6DC

0CE105SK6DC

0CE476SF6DC

0CE106SF6DC

0CK473CH56A

0CE106SF6DC

0CE105SK6DC

0CE106SF6DC

0CE476SF6DC

0CE105SK6DC

0CE476SF6DC

0CE1074F618

0CE226SF6DC

0CE227DF618

0CE105CK636

0CE106SF6DC

1UF 2012 16V 20% F(Y5V) R/TP

22UF MV 16V 20% R/TP(SMD) SMD

220UF MV 16V 20% R/TP(SMD) SMD

100UF MVG 16V 20% SMD R/TP

1UF 2012 16V 20% F(Y5V) R/TP

470UF MVG 16V 20% R/TP(SMD) SMD

10UF 3216 16V 10% X7R R/TP

47UF MVG 16V 20% SMD R/TP

10UF 3216 16V 10% X7R R/TP

47UF MVG 16V 20% SMD R/TP

10UF 3216 16V 10% X7R R/TP

47UF MVG 16V 20% SMD R/TP

470UF MVG 16V 20% R/TP(SMD) SMD

47UF MVG 16V 20% SMD R/TP

10UF 3216 16V 10% X7R R/TP

47UF MVG 16V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

0.047UF 1608 25V 10% R/TP X7R

10UF MVG 16V 20% R/TP(SMD) SMD

1UF MVG 50V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

47UF MVG 16V 20% SMD R/TP

1UF MVG 50V 20% SMD R/TP

47UF MVG 16V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

0.047UF 1608 25V 10% R/TP X7R

10UF MVG 16V 20% R/TP(SMD) SMD

1UF MVG 50V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

47UF MVG 16V 20% SMD R/TP

1UF MVG 50V 20% SMD R/TP

47UF MVG 16V 20% SMD R/TP

100UF SRA,SS 16V 20% FL TP 5

22UF MVG 16V 20% SMD R/TP

220UF STD 16V 20% FL TP 5

1UF SHL,SD 50V 20% FM5 BP(D) TP

10UF MVG 16V 20% R/TP(SMD) SMD

REPLACEMENT PARTS LIST

http://www.wjel.net

- 20 -

LOCA. NO PART NO DESCRIPTION

C507

C509

C511

C513

C515

C517

C519

C521

C523

C525

C527

C530

C531

C533

C541

C546

C548

C556

C558

C559

C562

C565

C568

C576

C583

C601

C606

C607

C612

C613

C618

C619

C624

C625

C628

C631

C634

C637

C643

C646

C649

C650

C653

C656

C659

C662

C665

C668

C669

C672

C675

C681

0CE106SF6DC

0CE107SF6DC

0CE335SK6DC

0CK474DH56A

0CE335SK6DC

0CE476SF6DC

0CE226SF6DC

0CE107SF6DC

0CE226SF6DC

0CE106SF6DC

0CE107SF6DC

0CK105DF64A

0CE106SK6DC

0CE108DH618

0CF4741L438

0CE477DK618

0CE477VF6DC

0CE227VF6DC

0CE477VF6DC

0CE227VF6DC

0CE477VF6DC

0CE227VF6DC

0CE477VF6DC

0CE107SF6DC

0CE476SF6DC

0CE107SF6DC

10UF MVG 16V 20% R/TP(SMD) SMD

100UF MVG 16V 20% SMD R/TP

3.3UF MVG 50V 20% SMD R/TP

0.47UF 2012 25V 10% R/TP X7R

3.3UF MVG 50V 20% SMD R/TP

47UF MVG 16V 20% SMD R/TP

22UF MVG 16V 20% SMD R/TP

100UF MVG 16V 20% SMD R/TP

22UF MVG 16V 20% SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

100UF MVG 16V 20% SMD R/TP

1UF 2012 16V 20% F(Y5V) R/TP

10UF MVG 50V 20% SMD R/TP

1000UF STD 25V 20% FL TP 5

0.47UF D 63V 5% TP 5 M/PE NI

470UF STD 50V 20% FL TP 5

470UF MV 16V 20% R/TP(SMD) SMD

220UF MV 16V 20% R/TP(SMD) SMD

470UF MV 16V 20% R/TP(SMD) SMD

220UF MV 16V 20% R/TP(SMD) SMD

470UF MV 16V 20% R/TP(SMD) SMD

220UF MV 16V 20% R/TP(SMD) SMD

470UF MV 16V 20% R/TP(SMD) SMD

100UF MVG 16V 20% SMD R/TP

47UF MVG 16V 20% SMD R/TP

100UF MVG 16V 20% SMD R/TP

LOCA. NO PART NO DESCRIPTION

C682

C684

C685

C686

C687

C8102

C8103

R1119

R1122

R1531

R1532

L2502

L2504

L2507

L2509

L510

L511

L512

L513

L601

L603

L605

L607

C27

CN107

CN108

CN1107

CN1108

CN1110

CN1111

CN1112

CN1601

CN1602

CN1701

CN2101

CN2451

CN2501

CN2502

CN301

CN302

CN401

CN501

CN502

CN601

CN602

CN603

CN604

CN605

0CK105DF64A

0CE226SF6DC

0CE227VF6DC

0CK105DF64A

0CZZVSB015A

0CK105DF64A

6140VB0004B

6140VB0024A

6140VB0004B

366-036B

6630VE00731

366-932C

366-921G

366-921L

366-932E

366-932C

6602T11001A

366-921L

366-921H

366-932E

366-932C

366-932B

366-921L

366-932C

366-932B

366-921J

1UF 2012 16V 20% F(Y5V) R/TP

22UF MVG 16V 20% SMD R/TP

220UF MV 16V 20% R/TP(SMD) SMD

1UF 2012 16V 20% F(Y5V) R/TP

PCK2 337 1.0UF 275V 10% BULK X-CAP

1UF 2012 16V 20% F(Y5V) R/TP

COIL,CHOKE 26UH

COIL,CHOKE LPK-1322A 22UH +-10%

COIL,CHOKE 26UH

CONNECTOR,WAFER STAPLE

CONNECTOR,WAFER 10022HS-31A02

CONNECTOR,WAFER IL-G-04P

CONNECTOR,WAFER 8PIN 2.54MM

CONNECTOR,WAFER 12PIN 2.54MM

CONNECTOR,WAFER 6PIN 2.54MM

CONNECTOR,WAFER IL-G-04P

WAFER,FI-TWE21P-VF JAE 21P

CONNECTOR,WAFER 12PIN 2.54MM

CONNECTOR,WAFER 9PIN 2.54MM

CONNECTOR,WAFER 6PIN 2.54MM

CONNECTOR,WAFER IL-G-04P

CONNECTOR,WAFER IL-G-03P

CONNECTOR,WAFER 12PIN 2.54MM

CONNECTOR,WAFER IL-G-04P

CONNECTOR,WAFER IL-G-03P

CONNECTOR,WAFER 10PIN 2.54MM

REPLACEMENT PARTS LIST

WAFER

COIL

http://www.wjel.net

LG MW 71PY10 User manual

Popular Monitor manuals by other brands