LG MZ-42PM10 User manual

PLASMA MONITOR
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS : RF-04GA
MODEL : MZ-42PM10/B/14
website:http://biz.LGservice.com
e-mail:http://www.LGEservice.com/techsup.html

- 2 -
CONTENTS
CONTENTS.............................................................................................................2
SAFETY PRECAUTIONS .......................................................................................3
ADJUSTMENT INSTRUCTIONS ............................................................................4
SPECIFICATIONS................................................................................................ 10
ADJUSTMENT INSTRUCTIONS ..........................................................................13
TROUBLE SHOOTING GUIDE.............................................................................15
BLOCK DIAGRAM................................................................................................26
EXPLODED VIEW.................................................................................................28
EXPLODED VIEW PARTS LIST...........................................................................29
REPLACEMENT PARTS LIST..............................................................................30
SCHEMATIC DIAGRAM ...........................................................................................
PRINTED CIRCUIT BOARD .....................................................................................

- 3 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in
the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to
prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during
the servicing of a receiver whose chassis is not isolated from
the AC power line. Use a transformer of adequate power rating
as this protects the technician from accidents resulting in
personal injury from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replace
it with the specified.
When replacing a high wattage resistor (Oxide Metal Film
Resistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Due to high vacuum and large surface area of picture tube,
extreme care should be used in handling the Picture Tube.
Do not lift the Picture tube by it's Neck.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source,
connect an electrical jumper across the two AC plug prongs.
Place the AC switch in the on position, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
ohm-meter lead in turn to each exposed metallic parts such as
antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC
voltmeter with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC
voltage measurements for each exposed metallic part. Any
voltage measured must not exceed 0.75 volt RMS which is
corresponds to 0.5mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
1.5 Kohm/10W
To Instrument's
exposed
METALLIC PARTS
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
AC Volt-meter
IMPORTANT SAFETY NOTICE
0.15uF

DESCRIPTION OF CONTROLS
- 4 -
- When using the remote control aim it at the remote control sensor of the set.
- There's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature.
POWERMUTE
PIP INPUT MULTIMEDIA
EXIT ARC MENU
VOL OK
123
456
7
PSM SSM
8 9
0
VOL
SPLIT ZOOM PIP/DW SLEEP
SCAN-
SKIP-
WIN. SIZE
SCAN+ PLAY
POSITION
SKIP+ STOP
SWAP
POWER PAUSE
INPUT SELECT
MULTIMEDIA
Selects the Component, RGB or DVI
modes.
WIN.SIZE
Adjusts the sub picture size.
POWER
switches the set on from standby or
off to standby.
ARC
Changes the picture format.
MENU
Displays on screen menus one by
one.
Exits the current menu.
Memorizes menu changes.
SSM
To select the sound appropriate to
your viewing programme character.
NUMBER buttons
SLEEP
Sets the sleep timer.
PIP/DW
Switches the sub picture on or off.
Selects PIP or DW modes.
DVD BUTTONS
controls a LG DVD player.
SWAP
Alternates between main and sub pic-
ture.
INPUT SELECT
EXIT
Clears all on-screen displays.
PIP INPUT
Selects the input mode for the sub pic-
ture.
MUTE
Switches the sound on or off.
DD/ EE
Selects a menu option.
FF/ GG(Volume Up/Down)
Increases/decreases sound level.
Adjusts menu settings.
OK
accepts your selection or displays the
current mode.
PSM
Adjusts the factory preset picture
according to the room.
SPLIT ZOOM
Enlarge the screen with regular
ration.
POSITION
Moves the sub picture to DD/ EEor FF/ GG
direction.

- 5 -
<Front Panel Controls>
MT/MZ-42/50PM10 series
MT/MZ-42/50PM20 series
ON/OFF
VOL
MENU
INPUT SELECT
ON/OFF
-Shown is a simplified representation of the set.
- Here shown may be somewhat different from your set.
1. Main Power Button
2. Remote Control Sensor
3. Power Standby Indicator
Illuminates red in standby mode, Illuminates green when the
set is turned on
4. INPUT SELECT Button
5. MENU
Displays on screen menus one by one.
Exits the current menu.
Memorizes menu changes.
6. DD/ EE
Selects a menu option.
FF/ GG(Volume Up/Down)
Increases/decreases sound level.
Adjusts menu settings.
1 2 3 4 5 6
1
4
5
6
23

- 6 -
<Back Panel>
RLRL
AC INPUT AUDIO INPUT
AUDIO INPUT
AUDIO INPUT VIDEO INPUT AUDIO INPUT S-VIDEO
RGB OUTPUTRGB INPUTDVI INPUT
RS-232C INPUT
(CONTROL/SERVICE)
REMOTE
CONTROL
YP B P R
AUDIO (MONO)
COMPONENT INPUT
RL
EXTERNAL SPEAKER
Connection to PC Connection to AV equipment
MZ-42PM10

- 7 -
<Back Panel>
AV1AV1
AC INPUT AUDIO INPUT RGB OUTPUTRGB INPUTDVI INPUT
RS-232C INPUT
(CONTROL/SERVICE)
REMOTE
CONTROL
RL
EXTERNAL SPEAKER
RCA Type
Scart Type
5
R
R
L
LRL
EXTERNAL SPEAKER
AC INPUT AUDIO INPUT
AUDIO INPUT
AUDIO INPUT VIDEO INPUT AUDIO INPUT S-VIDEO
RGB OUTPUTRGB INPUTDVI INPUT
RS-232C INPUT
(CONTROL/SERVICE)
REMOTE
CONTROL
Y P B P R
AUDIO (MONO)
COMPONENT INPUT
1 2 3 645
1. CONTROL LOCK / REMOTE CONTROL
2. RS-232C INPUT(CONTROL/SERVICE) PORT
Connect to the RS-232C port on a PC.
3. DVI INPUT / AUDIO INPUT / RGB INPUT SOCKETS
Connect the monitor output socket of the PERSONAL COM-
PUTER to this socket.
RGB OUTPUT SOCKET
You can watch the RGB signal on another monitor, connect
RGB OUTPUT to another monitor’s PC input port.
4. EXTERNAL SPEAKER OUTPUT (8 ohm)
Connect to optional external speaker(s).
*For further information, refer to ‘Speaker & Speaker Stand’
manual.
5. AUDIO / COMPONENT INPUT / S-VIDEO / VIDEO INPUT /
AUDIO INPUT SOCKETS
EURO SCART SOCKET
Note: The interface board (AP-42PM10/11) is not equipped
on MT/MZ-42PM10/12X/20 series / MT/MZ-50PM10/20
series models. Contact your dealer for buying this optional
item.
6. POWER CORD SOCKET
This Monitor operates on an AC power. The voltage is indi-
cated on the Specifications page. Never attempt to operate
the Monitor on DC power.
MZ-42PM10

- 8 -
Location and Function of Controls
Location and Function of Controls
<Back Panel>
RLRL
AC INPUT AUDIO INPUT
AUDIO INPUT VIDEO INPUT AUDIO INPUT S-VIDEO
RGB OUTPUTRGB INPUTDVI INPUT
RS-232C INPUT
(CONTROL/SERVICE)
REMOTE
CONTROL
Y P B P R
(MONO)
COMPONENT INPUT
RL
EXTERNAL SPEAKER
AV2
AV1
Connection to PC Connection to AV equipment
MZ-42PM14

- 9 -
<Back Panel>
RLRL
AC INPUT AUDIO INPUT
AUDIO INPUT VIDEO INPUT AUDIO INPUT S-VIDEO
RGB OUTPUTRGB INPUTDVI INPUT
RS-232C INPUT
(CONTROL/SERVICE)
REMOTE
CONTROL
Y P B P R
(MONO)
COMPONENT INPUT
RL
EXTERNAL SPEAKER
AV2
AV1
1 2 3 645
1. CONTROL LOCK / REMOTE CONTROL
2. RS-232C INPUT(CONTROL/SERVICE) PORT
Connect to the RS-232C port on a PC.
3. DVI INPUT / AUDIO INPUT / RGB INPUT SOCKETS
Connect the monitor output socket of the PERSONAL COMPUTER to this socket.
RGB OUTPUT SOCKET
You can watch the RGB signal on another monitor, connect RGB OUTPUT to another monitor’s PC input
port.
4. EXTERNAL SPEAKER OUTPUT (8 ohm)
Connect to optional external speaker(s).
* For further information, refer to ‘Speaker & Speaker Stand’ manual.
5. COMPONENT / AUDIO INPUT SOCKETS
S-VIDEO / AUDIO (L/MONO) INPUT SOCKETS
VIDEO / AUDIO (L/MONO) INPUT SOCKETS
EURO SCART SOCKET
Note: If you want to use your external hi-fi stereo system, turn off the internal speakers of the set.
6. POWER CORD SOCKET
This Monitor operates on an AC power. The voltage is indicated on the Specifications page. Never
attempt to operate the Monitor on DC power.
MZ-42PM14

- 10 -
SPECIFICATIONS
NOTE : Specifications and others are subject to change without notice for improvement .
VApplication Range
This spec is sheet is applide to the 42”,50” PDP TV used RF-04GA chassis.
V Specification
Each part is tested as below without special appointment.
1) Temperature : 25¡5°C (77¡9°F)
2) Relative Humidity: 65¡10%
3) Power Voltage: Standard Input voltage (100V-240V~, 50/60Hz)
* Standard Voltage of each product is marked by models.
4) Specification and performance of each parts are followed each drawing and specification by part number in
accordance with BOM.
5)
The receiver must be operated for about 20 minutes prior to the adjustment .
VTest and Inspection Method
1) Performance : LGE TV test method followed.
2) Demanded other specification
Safety: CE, IEC specification
EMC : CE, IEC
Remark
Safety : IEC60065
EMI : EN55022
EMS : EN55024
Safety : IEC60065,IE60950
EMI : EN55022
Remark
TEST
Model Name
MZ-42PM10
MZ-42PM12X
MZ-50PM10
MZ-50PM20
MT-42PM10
MT-42PM20
MT-42PM12X
MT-50PM10
MT-50PM20
Market
EU
Non-EU
Market Place
EU
Non-EU
Chassis
RF-04GA
Model Name
MZ-42PM10
MZ-42PM12X
MZ-50PM10
MZ-50PM20
MT-42PM10
MT-42PM20
MT-42PM12X
MT-50PM10
MT-50PM20
Brand
LG
LG

VGeneral Specification
1. General Specification (42” VGA MODULE)
2. General Specification (42” XGA MODULE)
3. General Specification (50” XGA MODULE)
- 11 -
Remark
PDP
LGE
Maker : NBK / Mitsui / LG Chemical
LGE SPEC
Maker : SONY / Murata / Sanken
Specification
42 inch wide Color Display Module
16:9
PDP42V6000
45% Total light transmittance (E- Mesh)
1) Temp : 0~40 deg
2) Humidity : 0~85%
1) Temp : -20~60 deg
2) Humidity : 0~85%
AC100 ~ 240V, 50/60Hz
No
1
2
3
4
5
6
7
Item
Display Screen Device
Aspect Ratio
PDP Module
Screen Filter
Operating Environment
Storage Environment
Input Voltage
Remark
PDP
Maker : NBK / Mitsui / LG Chemical
LGE SPEC
Maker : SONY / Sanken
Specification
42 inch wide Color Display Module
16:9
PDP42X1A###, RGB Closed Type
45% Total light transmittance (E- Mesh)
1) Temp : 0~40 deg
2) Humidity : 0~85%
1) Temp : -20~60 deg
2) Humidity : 0~85%
AC100 ~ 240V, 50/60Hz
No
8
9
10
11
12
13
14
Item
Display Screen Device
Aspect Ratio
PDP Module
Screen Filter
Operating Environment
Storage Environment
Input Voltage
Remark
PDP
LGE
Maker : NBK / Mitsui / LG Chemical
LGE SPEC
Maker : SONY / Sanken
Specification
50 inch wide Color Display Module
16:9
PDP50X2###, RGB Closed Type
45% Total light transmittance (E- Mesh)
1) Temp : 0~40 deg
2) Humidity : 0~85%
1) Temp : -20~60 deg
2) Humidity : 0~85%
AC100 ~ 240V, 50/60Hz
No
15
16
17
18
19
20
21
Item
Display Screen Device
Aspect Ratio
PDP Module
Screen Filter
Operating Environment
Storage Environment
Input Voltage

VModel Specification
1. MZ-42PM10 / 42PM12X / 50PM10 / 50PM20
2. MT-42PM10 / 42PM20 / 42PM12X / 50PM10 / 50PM20
- 12 -
Remark
4 System : PAL, B/G/I/D/K, SECAM L/,
NTSC4.43, PAL60
4 System : PAL, B/G/I/D/K, SECAM L/,
NTSC4.43, PAL60
Up to UXGA@60Hz/480P
Up to UXGA@60Hz/480P
DVI-D
L/R Input
Specification
EU
PAL, SECAM
PAL, SECAM, NTSC
Y/ Cb/ Cr, Y/ Pb/ Pr
RGB-PC/DTV
RGB-PC/DTV
DVI-PC/DTV
PC Audio, Component,S-VHS, CVBS
Discrete IR
No
22
23
24
25
26
27
28
29
30
Item
Market
Scart Jack (2EA )
S-AV Input (1EA )
Component Input (1EA )
RGB Input (1EA )
RGB Outpu t (1EA )
DVI Input (1EA )
Audio Input (4EA )
Wired Control
Remark
4 System : PAL, B/G/I/D/K, SECAM L/,
NTSC4.43, PAL60
4 System : PAL, B/G/I/D/K, SECAM L/,
NTSC4.43, PAL60
Up to UXGA@60Hz/480P
Up to UXGA@60Hz/480P
DVI-D
L/R Input
Specification
Non-EU
PAL, SECAM, NTSC
PAL, SECAM, NTSC
Y/ Cb/ Cr, Y/ Pb/ Pr
RGB-PC/DTV
RGB-PC/DTV
DVI-PC/DTV
PC Audio, Component,S-VHS, CVBS
Discrete IR
No
31
32
33
34
35
36
37
38
39
Item
Market
Scart Jack (2EA )
S-AV Input (1EA )
Component Input (1EA )
RGB Input (1EA )
RGB Outpu t (1EA )
DVI Input (1EA )
Audio Input (4EA )
Wired Control

- 13 -
ADJUSTMENT INSTRUCTIONS
1. Application Object
This spec sjeet os applied all of the 42”, 50”, RF-04GA
chassis bymanufacturing LG TV Plant or sort plant.
2. Specification
(1) Because this is not a hot chassis, it is not necessary to
use an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.
(4) The input voltage of the receiver must keep 100-220V~,
50/60Hz.
(5) The receiver must be operated for about 15 minutes prior
to the adjustment.
OAfter RGB Full white HEAT-RUN Mode, the receiver must
be operated prior to adjustment.
OEnter into HEAT-RUN MODE
1) Press the POWER ON KEY on R/C for adjustment.
2) OSD display and screen display 100% full WHITE
PATTERN.
[Set is activated HEAT-RUN without signal generator in
this mode.
[Single color pattern(RED/BLUE/GREEN) of HEAT-RUN
mode uses to check pannel.
Caution) If you turn on a still screen more than 20 minutes
(Especially digital pattern, cross hatch pattern), a after
image may be occur in the black level part of the
screen
.
3. POWER PCB Assy Voltage
Adjustments (Va, Vs Voltage Adjustments)
3-1. Test Equipment :D.M.M. 1EA
3-2. Connection Diagram for Measuring
Refer to [Fig 1]
3-3. Adjustment Method for
(1) Va Adjustment
1) After receiving 100% Full White Pattern, HEAT RUN.
2) Connect + terminal of D.M.M to Va pin of P805, connect
- terminal to GND pin of P805.
3) After turningVR351, voltage of D.M.M adjustment as
same as Va voltage which on lable of panel right/top
(Deviation; ±0.5V)
(2) Vs Adjustment
1) Connect + terminal of D.M.M to Vs pin of P805, connect
– terminal to GND pin of P805.
2) After turning RV551, voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top.
(Deviation; ±0.5V)
4. Auto RGB Color balance
4-1 Pattern Equipment :
PC Pattern Generator( 801F or VG828 )
(16Gray Scale Pattern output(RGB output Level: 0.7Vp-p))
4-2 Method of Auto RGB Color Balance
(1) Input RGB Source: 16Gray Scale Pattern output
(RGB output Level: 0.7Vp-p)
(2) Press ADJ KEY on R/C for adjustment.
(3) Press Vol. +KEY and Operate To Set.
(4) Auto-RGB OK means completed adjustment.
P805
P804
P806
P803
P802
P801
VR351
GND
GND
Va
Va
Vs
Vs
Vs
Vs ADJ
VR551
VR5
Vs ADJ
[Fig. 1] Connection Diagram of Power Adjustment for Measuring
[Fig. 2] Auto RGB Color Balance Test Pattern

- 14 -
4-3 Adjustment of White Balance
(1) Required Equipment
Color Analyzer( CA-100 or same product)
(2) Connecting diagram of equipment for measuring.
If you are adjusting a MZ Model, Use the RCA to SCART(Out)
cable to input a AV signal.
(3) Adjustment of White Balance
O Operate the zero-calibration of the CA-100, then stick sensor
to PDP module surface when you adjust..
O For manual adjustment, It is also possible by the following
sequence.
1) Select white pattern of heat-run mode by pressing power
on key on remote control for adjustment then operate
heat run more than 15 minute.
2) Supply Gray Pattern(216 Gray full window) signal to
VIDEO input.(RZ-42PM10: AV4 input) refer to [fig3]
3) To adjust High Light, stick sensor to 216 Gray level
pattern, press ADJ key twice(White Balance) on remote
control.
For adjustment and D/Eon remote control for adjustment
mode to select Red Gain and Blue Gain, press Vol +.-key
and adjust it until color coordination becomes as below.
[RF-04GA:RZ-42PM10]:
X; 0.283¡¡
æ
0.003, Y; 0.297¡¡
æ
0.003,
Color Temperature;9,300 °K¡¡
æ
500°K
4) Exit adjustment mode using VKey.
4-4 Auto Adjustment Map(RS-232C)
5. DDC Data Input
5-1. Required Test Equipment
(1) A jig for adjusting PC, DDC (PC serial to D-sub
Connection equipment)
(2) S/W for writing DDC (EDID Data Write & Read)
(3) D-sub 15P Cable, D-Sub to DVI Connector (Connect to
DVI Jack)
5-2. Setting of Device
5-3. Preparation for Adjustment
(1) Set devices as above and turn the PC, jig on.
(2) Put S/W for writing DDC (EDID data Write & Read) into
operation. (operated in DOS mode.)
5-4. Sequence of Adjustment
(1) DDC Data Input for Analog-RGB
1) Put the set on the table and turn the power on.
2) Connect PC Serial to D-sub 15P Cable of jig for DDC
adjustment to RGB terminal (D-Sub 15Pin).
3) Operate S/W for DDC record and select DDC data for
Analog RGB in Model Menu.
4) Operate EDID Write command.
5) Operate EDID Read command and check whether
Check Sum is OK.
6) If Check Sum is NG, repeat 3) ~ 4).
7) If Check Sum is OK, DDC data for Analog-RGB input is
completed.
(2) DDC Data input for Digital-RGB(DVI)
1) Connect PC Serial to DVI Cable of jig for DDC
adjustment to DVI terminal (DVI Jack).
2) Operate S/W for DDC record and select DDC data for
digital RGB in model menu.
3) Operate EDID Write command.
4) Operate EDID Read command and check whether
Check sum is OK
5) If Check sum is NG, repeat 3) ~ 4).
6) If Check sum is OK, DDC data for Analog-RGB input is
completed.
PC
JIG
PDP
SET
[Fig. 3] White Balance Adjustment
Window
Pattern
AV Signal Input
COLOR
ANALYZER
TYPE; CA-100
High Light Adjustor
(216gray pattern)
MSPG-2100or
MSTG-5200
RS-232C Serial Communication
Type
Baud Rate
115200
Index
R Gain
G Gain
B Gain
R Offse t
G Offse t
B Offset
Data bit
8
Cmd1 Cmd2
j a
j b
j c
j d
j e
j f
Stop bit
1
Parity
NONE
Protocol
Setting
Data Min Value
00(00)
00(00)
00(00)
00(00)
00(00)
00(00)
Max Value
255(FF)
255(FF)
255(FF)
255(FF)
255(FF)
255(FF)
RF-043B_PDP42

- 15 -
TROUBLE SHOOTING GUIDE
1. Power Board
1-1. The whole flowchart which it follows in voltage output state
Start check
Manufacture enterprise
meaning of a passage
1. Check the Power Off
condition.
Doesn't the
screen whole come
out?
It is identical
with Power Off
condition?
Yes
Yes
No
No
No
No
No
2. Check the Interface
signal condition.
Is the Interface
signal operated?
Yes
3. Check the St-by 5V
signal circuit.
Doesn't the
low pressure output
come out?
Doesn't the
St-by 5V signal
come out?
Yes
Yes
No
4. Check the 5V Monitor
signal circuit.
Doesn't the
5V Monitor signal
come out?
Yes
7. Check the VSC Vs-ON
signal
Doesn't the
high tension output
come out?
Doesn't the
VSC signal Vs-ON
come out?
Yes
Yes
High tension
output voltage Drop
it occurs?
When
remove the
Y B/D Module
Input Connector, output
voltage Drop
it occurs?
When remove
the Y, Z B/D Module
Input Connector, Power
Board high tension output
voltage Drop
it occurs?
Yes No No
9. Check the Power
Board Output high
tension circuit
Yes
10. Check the Z B/D
Module Coutput circuit
Yes
When
remove the
Z B/D Module
Input Connector, output
voltage Drop
it occurs?
11. Check the Y B/D
Module Coutput circuit
Yes
No
8. Check the Vs, Va
voltage output circuit.
Doesn't the
Vs, Va voltage output
come out?
Yes
No
No
5. Check the VSC RL-ON
signal.
Doesn't the
VSC signal RL-ON
come out?
Yes
6. Check the VSC low
pressure output
Doesn't the
VSC low pressure
output come out?
Yes

- 16 -
1-2. Sony Power Board Structure
T502: Vs Trans
T702: Va Trans
T101: St-by Trans
T103: Low Voltage Trans
1 2 3

- 17 -
1-3. Sanken Power Board Structure
T221: Vs Trans
T271: Va Trans
T121: St-by Trans
T201: Low Voltage Trans
1 2 3

- 18 -
2. No Power
(1) Symptom
¯Does’t minute discharge at module.
¯Non does not come in into the front LED.
(2) Check follow
Is plug in power cord? Plug in power cord.
Yes
No
Is connect the Line Filter and Power
Switch Cable? Connect Cable.
Yes
No
Is connect the Power Switch and
Power Board Cable? Connect Cable.
Yes
No
Is normal the Fuse(F101) on Power
Board? Replace Fuse.
Yes
No
Is connect the Power Board and 7P
of VSC Board Cable? Connect Cable.
Yes
No
Is connect the Power Switch and
Power Board Cable?
After remove the cable connect to
Power Board(except the CN101
connection cable), authorizes the
AC voltage marking on manual.
When ST-BY 5V does not operate,
replace Power Board.
Connect Cable.
Yes
No

- 19 -
3. Protect Mode
(1) Symptom
¯After once shining, it does not discharge minutely
from module
¯The Rely falls(The sound is audible “click”)
¯It is converted with the color where the front LED
is red from green.
(2) Check follow
Is normal the Power
Board? Replace Power Board.
Is output the normality Low/High
voltage except Stand-by 5V?
Yes
No No
Is normal the each
connector? Replace connector.
Replace
Y-Board.
After connecting well each connector,
the normality it operates?
Yes
No No
Is normal the
Ctrl Board? Replace X-Board.
Is normal the output voltage after
remove P1, 2, 101, 300, 701, 702
connector of Ctrl-B/D?
Yes
No Yes
Is normal the
Y- Board?
Is normal the output
voltage after remove
P5, P6 connector of
Y-B/D?
Is normal the Fuse(F52) on Y-B/D?
(In case of open is replace)
Yes
No Yes Yes
Replace
Z-Board.
Is normal the
Z- Board?
Is normal the output
voltage after remove
P1 connector of
Z-B/D?
Is normal the Fuse(FS1, FS2) on Z-
B/D? (In case of open is replace)
Yes
No Yes
Is normal the
X- Board?
Is normal the output voltage after
remove P1, 2, 3, 4, 6, 7 connector of
X-B/D?
After remove P1, P2, P3, P4 output voltage
normality: Replace Right X-B/D
After remove P6, P7 output voltage
normality: Replace Left X-B/D
Yes
No Yes
Is normal the
VSC Board? Is normal the output voltage after remove P1000, P1200?
After crisis COF of each board, check the normality operates.
If in case normality operates, correspondence COF Fail is
replace the module.
After remove P1000 normal operation:
Replace Analog Board
After remove P1200 normal operation:
Replace Digital Board
Yes
No
Is normal the
COF of X, Y, Z?
No
Yes
Yes

- 20 -
4. No Raster
(1) Symptom
¯Does’t minute discharge at module.
¯It maintains the condition where the front LED is green.
(2) Check follow
Is normal the Power
Board? Replace Power Board.
Is output the normality Low/High
voltage except Stand-by 5V?
Yes
No No
Is normal the each
connector? Replace connector.
Replace
Y-Board.
After connecting well each connector,
the normality it operates?
Yes
No No
Is normal the
Ctrl Board? Replace X-Board.
Is normal the output voltage after
remove P1, 2, 101, 300, 701, 702
connector of Ctrl-B/D?
Yes
No Yes
Is normal the
Y- Board?
Is normal the output
voltage after remove
P5, P6 connector of
Y-B/D?
Is normal the Fuse(F52) on Y-B/D?
(In case of open is replace)
Yes
No Yes Yes
Replace
Z-Board.
Is normal the
Z- Board?
Is normal the output
voltage after remove
P1 connector of
Z-B/D?
Is normal the Fuse(FS1, FS2) on Z-
B/D? (In case of open is replace)
Yes
No Yes
Is normal the
X- Board?
Is normal the output voltage after
remove P1, 2, 3, 4, 6, 7 connector of
X-B/D?
After remove P1, P2, P3, P4 output voltage
normality: Replace Right X-B/D
After remove P6, P7 output voltage
normality: Replace Left X-B/D
Yes
No Yes
Is normal the
VSC Board? Is normal the output voltage after remove P403, P1300?
After crisis COF of each board, check the normality operates.
If in case normality operates, correspondence COF Fail is
replace the module.
After remove P403 normal operation:
Replace AV Fix Board
After remove P1300 normal operation:
Replace Digital Board
Yes
No
Is normal the
COF of X, Y, Z?
No
Yes
Yes