LG CM1930 User manual

Getting Started 3
Getting Started
1
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, re or the like.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects lled
with liquids, such as vases, shall be placed on the
apparatus.
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by
the European Directive 2002/96/EC.
2. All electrical and electronic products
should be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or
the local authorities.
3. The correct disposal of your
old appliance will help prevent
potential negative consequences
for the environment and human
health.
4. For more detailed information about
disposal of your old appliance,
please contact your city office,
waste disposal service or the shop
where you purchased the product.
CM1930-DU_AESPLLK_ENG.indd 3 2013-03-15 2:07:15
http:\\www.direcTutor.com

Getting Started4
Getting Started
1
Disposal of waste batteries/accumulators
1. When this crossed-out wheeled
bin symbol is attached to batteries/
accumulators of Your product
it means they are covered by
European Directive 2006/66/EC.
2. This symbol may be combined with
chemical symbols for mercury(Hg),
cadmium(Cd) or lead(Pb) if the
battery Contains more that 0.0005%
of mercury,0.002% of cadmium or
0.004% of lead.
3. All batteries/accumulators should
be disposed separately from
the municipal waste stream via
designated collection facilities
appointed by the government or
the local authorities.
4. The correct disposal of Your old
batteries/accumulators will help
to prevent potential negative
consequences for the environment,
animal and human health.
5. For more detailed information
about disposal of Your old batteries/
accumulators, please contact Your
city office, waste disposal service or
the shop where You purchased the
product.
LG Electronics hereby declares that this/these
product(s) is/are in compliance with the essential
requirements and other relevant provisions of
Directive 2004/108/EC, 2006/95/EC, 2009/125/EC
and 2011/65/EU.
Contact oce forcomplianceof this product
LG Electronics Inc.
EU Representative, Krijgsman 1,
1186 DM Amstelveen, The Netherlands
Please note that this is NOT a Customer Service
contact point. For Customer Service Information,
see Warranty Card or contact the dealer that you
purchased this product.
CM1930-DU_AESPLLK_ENG.indd 4 2013-03-15 2:07:15
http:\\www.direcTutor.com

Table of Contents 5
1
2
3
4
5
Table of Contents
1 Getting Started
2 Safety Information
6 Unique Features
6 Accessories
6 Playable file Requirement
6 – MP3/WMA music file requirement
7 – Compatible USB Devices
7 – USB device requirement
8 Remote Control
9 Front Panel
10 Rear Panel
2 Connecting
11 Connecting to speakers
11 – Attaching the speakers to the unit
11 Antenna Connection
12 Optional Equipment Connection
12 – USB Connection
12 – PORT. IN Connection
13 – PHONES Connection
3 Operating
14 Basic Operations
14 – CD/USB Operations
14 – Selecting a folder
15 Other Operations
15 – Programmed Playback
15 – Displaying file information (ID3 TAG)
15 – Turn off the sound temporarily
15 – Listening to music from your external
device
15 – Auto Power Down
16 Radio Operations
16 – Listening to the radio
16 – Presetting the Radio Stations
16 – Improving poor FM reception
16 – Deleting all the saved stations
17 – Seeing information about a Radio
station
17 Setting the Clock
18 – Setting the alarm
18 – Sleep Timer Setting
18 – Dimmer
19 Sound adjustment
19 – Setting the surround mode
19 Advanced Operations
19 – Recording to USB
19 – Pausing recording
20 – To select recording bit rate and speed
4 Troubleshooting
21 Troubleshooting
5 Appendix
22 Specifications
23 Maintenance
23 – Handling the Unit
23 – Notes on Discs
23 Trademarks and Licenses
CM1930-DU_AESPLLK_ENG.indd 5 2013-03-15 2:07:15
http:\\www.direcTutor.com

Getting Started 7
Getting Started
1
Compatible USB Devices
yMP3 Player : Flash type MP3 player.
yUSB Flash Drive :
Devices that support USB 2.0 or USB 1.1.
yThe USB function of this unit does not support
all USB devices.
USB device requirement
yDevices which require additional program
installation when you have connected it to a
computer, are not supported.
yDo not extract the USB device while in operation.
yFor a large capacity USB, it may take longer than
a few minute to be searched.
yTo prevent data loss, back up all data.
yIf you use a USB extension cable or USB hub, the
USB device is not recognized.
yUsing NTFS le system is not supported.
(Only FAT(16/32) le system is supported.)
yThis unit is not supported when the total
number of les is 1 000 or more.
yExternal HDD, Card readers, Locked devices, or
hard type USB devices are not supported.
yUSB port of the unit cannot be connected to PC.
The unit cannot be used as a storage device.
ySome USB may not work with this unit.
CM1930-DU_AESPLLK_ENG.indd 7 2013-03-15 2:07:16
http:\\www.direcTutor.com

Operating14
Operating
3
Basic Operations
CD/USB Operations
1. Insert the disc by pressing Bor connect the
USB device to the USB port.
2. Select the CD or USB function by pressing
FUNCTION on the remote control or FUNC. on
the unit.
3. Select a track/file you want to play by pressing
C/V on the remote control or Y/U
on the unit.
To Do this
Stop Press ZENTER on the remote
control or Ion the unit.
Playback Press d/Mon the remote control
or Ton the unit.
Pause During playback, press d/Mon the
remote control or T on the unit.
Skip to the
next/previous
track/le
During playback, press Von the
remote control or Uon the unit
to go to the next track/le.
Playing less than 2 seconds, press
Con the remote control or Y
on the unit to go to the previous
track/le.
Playing after 3 seconds, press C
on the remote control or Yon
the unit to go to the beginning of
the track/le.
Search for
a section
within a track
Press and hold C/Von the
remote control or Y/U on
the unit during playback and
release it at the point you want to
listen to.
Play
repeatedly or
randomly
Press REPEAT(MENU) on the
remote control repeatedly, the
display will be changed in the
following order.
RPT1 -> RPT ALL -> RANDOM ->
OFF
Selecting a folder
1. In stop status,press PRESET/FOLDER W/Son
the remote control repeatedly until a desired
folder appears.
2. Press
d/Mto play it. The first file of folder will
be played. (During playback, if you selecting a
folder you want, this step is not necessary.)
yFolders/Files on the CD or USB are
recognized as below.
*ROOT
File_01
: File
: Folder
File_02
File_03
File_04
File_05
File_06
File_07
File_09
File_10
Folder_01
Folder_02
Folder_03
Folder_04
File_08
yFiles and folders will be presented in order
recorded and may be presented dierently
according to the record circumstances.
yFolders and les will be presented as the
following order :
Folder : Folder_01 Folder_03
Folder_02 Folder_04
File : File_01 File_02 File_03 File_04
File_05 File_08 File_09 File_06
File_07 File_10
y*ROOT : It is “ROOT” which is the rst screen
you can see when a computer recognizes
the storage device.
yThe DTS is not supported.
, Note
CM1930-DU_AESPLLK_ENG.indd 14 2013-03-15 2:07:18
http:\\www.direcTutor.com

Operating 15
Operating
3
Other Operations
Programmed Playback
The program function enables you to store your
favorite les from any disc or USB device.
A program can contain 64 tracks/les.
1. Insert a CD or a USB and wait for it to be
ordered.
2. Press PROGRAM/MEMORY on the remote
control in stop status.
3. Press
C/Von the remote control or Y/
Uon the unit to select a track/file.
4. Press PROGRAM/MEMORY on the remote
control again to save and select a next track/file.
5. Press
d/Mon the remote control or Ton the
unit to play the programmed music tracks/files.
6. To clear your selection, press ZENTER on the
remote control or Ion the unit twice.
The programs are also cleared when the disc
or USB device is removed, the unit is powered
o or the function is switched to others.
, Note
Displaying file information
(ID3 TAG)
While playing an MP3 le containing le
information, you can display the information by
pressing INFO.
Turn off the sound temporarily
Press @on the remote control to mute your
sound.
You can mute your sound, for example, to answer
the telephone,“MUTE ON” will appear for a while in
the display window.
To cancel it, press @again or change the volume
level. Then "MUTE OFF" will appear.
Listening to music from your
external device
The unit can be used to play the music from many
types of external device.
(Refer to the page 12)
1. Connect the external device to the PORT. IN
connector of the unit.
2. Turn the power on by pressing 1/!.
3. Select the PORTABLE function by pressing
FUNCTION on the remote control or FUNC. on
the unit.
4. Turn the external device and start playing
music.
Auto Power Down
This unit will be o itself to save electronic
consumption in the case main unit is not
connected to external device and is not used for 25
minutes. So does this unit after 6 hours since Main
unit has been connected to other device using
analog input.
CM1930-DU_AESPLLK_ENG.indd 15 2013-03-15 2:07:18
http:\\www.direcTutor.com

Operating16
Operating
3
Radio Operations
Listening to the radio
1. Press FUNCTION on the remote control or
FUNC. on the unit until FM appears in the
display window.
The last received station is tuned in.
2. Auto tuning : Press TUN.-/+ on the remote
control or Y/U on the unit for about 2
seconds until the frequency indication starts
changing, then release. scanning stops when
the unit tunes in a station.
Manual tuning: Press TUN.-/+ on the remote
control or Y/U on the unit repeatedly.
3. Adjust the volume by using VOL+/- on the
remote control or VOLUME-/+ on the unit
repeatedly.
Presetting the Radio Stations
You can preset 50 stations for FM.
Before tuning, make sure to turn down the volume.
1. Press FUNCTION on the remote control or
FUNC. on the unit until FM appears in the
display window.
2. Select the desired frequency by pressing
TUN.-/+ on the remote control or Y/U
on the unit.
3. Press PROGRAM/MEMORY. A preset number
will blink in the display window.
4. Press PRESET/FOLDER W/Son the remote
control to select the preset number you want.
5. Press PROGRAM/MEMORY. The station is
stored.
6. Repeat steps 2 to 5 to store other stations.
7. To listen a preset station, press PRESET/FOLDER
W/S.
Improving poor FM reception
Press d/Mon the remote control or Ton the
unit. This will change the tuner from stereo to
mono. Then the reception will be better than
before.
Deleting all the saved stations
1. Press and hold PROGRAM/MEMORY for
two seconds. “ERASE”will blink in the display
window.
2. Press PROGRAM/MEMORY to erase all saved
radio stations.
CM1930-DU_AESPLLK_ENG.indd 16 2013-03-15 2:07:18
http:\\www.direcTutor.com

Operating 17
Operating
3
Seeing information about a
Radio station
The FM tuner is supplied with the RDS (Radio Data
System) facility. This shows information about the
radio station being listened to. Press SET/RDS
repeatedly to cycle through the various data types. :
PS (Programme Service Name)
The name of the channel will appear in
the display
PTY (Programme Type Recognition)
The programme type (e.g. Jazz or News)
will appear in the display.
RT (Radio Text)
A text message contains special
information from the broadcast station.
This text may scroll across the display.
CT (Time controlled by the channel)
This shows the time and date as
broadcast by the station.
You can search the radio stations by programme
type by pressing SET/RDS. The display will show
the last PTY in use. Press PTY one or more times to
select your preferred programme type. Press and
hold TUN.-/+. The tuner will search automatically.
When a station is found, the search will stop.
Setting the Clock
1. Turn the unit on.
2. Press and hold CLOCK.
3. Choose time mode by pressing C/V.
- 12:00(for an AM and PM display) or 0:00(for a
24hour display)
4. Press SET/RDS to confirm your selection.
5. Select the hours by pressing C/V.
6. Press SET/RDS.
7. Select the minutes by pressing C/V.
8. Press SET/RDS.
9. If you want to reset the clock, repeat steps 2-8.
CM1930-DU_AESPLLK_ENG.indd 17 2013-03-15 2:07:18
http:\\www.direcTutor.com

Operating18
Operating
3
Setting the alarm
You can use the unit as an alarm clock.
You have to set the clock before setting the alarm.
1. Turn the unit on.
2. Press and hold TIMER.
3. Each of functions will blink. Press SET/RDS
to select a sound source you want. (CD/USB/
TUNER)
If you select FM function, select a preset station
by pressing C/V.
4. “ON TIME” will be displayed. This is your desired
time to the unit turns on.
Press C/Vto change the hours and
minutes and press SET/RDS to save.
5. “OFF TIME” will be displayed. This is your desired
time to the unit turns off.
Press C/Vto change the hours and
minutes and press SET/RDS to save.
6. Press
C/Vto change the volume and
press SET/RDS to save.
7. You can check the setting status.
8. If you want to reset the alarm, repeat steps 2-6.
yIf you set the clock time and alarm, you
can check the time and alarm by pressing
CLOCK even when the unit is turned o.
yIf the alarm is already set, press TIMER once
to cancel the alarm. To activate the alarm,
press TIMER once again.
yIf the clock time or the alarm is already set,
press and hold CLOCK or TIMER for at least
2 seconds to reset the clock timer or the
alarm.
yAlarm function only works when the unit is
turned o.
yIf the time you set is up, the unit will be
turned on automatically.
yIf you unplug the cord from an outlet, the
clock setting you set won’t be stored.
, Note
Sleep Timer Setting
Press SLEEP repeatedly to select delay time
between 10 and 180 minutes. After the delay
time, the unit will be turned o. (You can see the
following order, 180 ->150 -> 120 -> 90 -> 80 -> 70
-> 60 -> 50 -> 40 -> 30 -> 20 -> 10)
To cancel the sleep function, press SLEEP
repeatedly until the display window get bright.
•Press SLEEP. The remaining time appears in
the display window.
•Sleep function will work after dimmer
function.
, Note
Dimmer
Press SLEEP once. The display window will
be darkened by half. To cancel it, press SLEEP
repeatedly until the display window get bright.
CM1930-DU_AESPLLK_ENG.indd 18 2013-03-15 2:07:18
http:\\www.direcTutor.com

Operating 19
Operating
3
Sound adjustment
Setting the surround mode
This system has a number of pre-set surround
sound elds. You can select a desired sound mode
by using EQ.
The displayed items for the Equalizer may be
dierent depending on sound sources and eects.
On Display Description
AUTO EQ
Sets the sound equalizer on the
mode that is the most similar to
the genre which is included in
the MP3 ID3 tag of song les.
MP3 -- OPT
This function is optimized for
compressible MP3/WMA le. It
improves the treble sound.
POP
CLASSIC
ROCK
This program lends an
enthusiastic atmosphere to the
sound, giving you the feeling
you are at an actual pop, classic
or rock concert.
BASS Reinforce the treble, bass and
surround sound eect.
BYPASS You can enjoy the sound
without equalizer eect.
Maybe you need to reset the surround mode,
after switching the input, sometimes even
after the sound track changed.
, Note
Advanced Operations
Recording to USB
You can record a various sound sources to USB.
1. Connect the USB device to the unit.
2. Select a function by pressing FUNCTION on the
remote control or FUNC. on the unit.
One track/file recording - You can record to USB
after playing a track/file you want.
All tracks/files recording - You can record to USB
after stop.
Program list recording - After showing the
programmed list, you can record it to USB.
(Refer to the page 15)
3. Start the recording by pressing REC on the
remote control.
4. To stop recording, press ZENTER on the
remote control or Ion the unit.
Pausing recording
During recording, press REC on the remote
control to pause recording. Press it again to restart
recording.(Only Radio)
CM1930-DU_AESPLLK_ENG.indd 19 2013-03-15 2:07:18
http:\\www.direcTutor.com

Operating20
Operating
3
To select recording bit rate
and speed
1. Press REC for longer than 3 seconds.
2. Use
C/Vto select the bit rate.
3. Press REC again to select the recording speed.
4. Press
C/Vto select a desired recording
speed. (CD Function Only)
X1 SPEED
- You can listen to music while recording it.
(Audio CD Only)
X2 SPEED
- You can just record the music file.
5. Press REC to finish the setting.
yYou can check the recording percentage
rate for the USB record on the display
window during the recording.
(MP3/WMA CD Only)
yDuring recording MP3/WMA, there is no
sound.
yWhen you stop recording during playback,
the le that has been recorded at that time
will be stored. (Except MP3/WMA les)
yDo not remove the USB device or turn
o the unit during USB recording. If not,
an incomplete le may be made and not
deleted on PC.
yIf USB recording does not work, the
message like “NO USB”, “ERROR”, “FULL” or “NO
REC” is displayed on the display window.
yMulti card reader device or External HDD
can not be used for USB recording.
yA le is recorded by about 512 Mbyte when
you record for a long term.
yIt’ll be stored as follows.
AUDIO CD MP3/WMA The other
source*
* : TUNER, PORTABLE and the like.
, Note
The making of unauthorized copies of copy-
protected material, including computer
programs, les, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal oense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights
CM1930-DU_AESPLLK_ENG.indd 20 2013-03-15 2:07:19
http:\\www.direcTutor.com