LIBERTY AV SOLUTIONS DIGITALINX DL-PSU8 User manual

11675 Ridgeline Drive
Colorado Springs, CO
80921
Rev 191204 Phone: [phone]
Toll-Free: 800-530-8998
Fax: [phone]
DL-PSU8 Quick Install Guide
This guide is for quick installaon only.
For complete owners manual go to www.libav.com or use a QR reader to access the
manual via QR code below.
Scan QR Code with your Smart-phone or Tablet

DL-PSU8 Quick Guide
3
The DL-PSU8 is an integrated switching power supply designed for converng AC into DC power. It
provides 2 AC input channels and 8 DC output channels. Input voltage is 100~240VAC, output voltage
is selectable per output channel; 5/12/18/24/48V DC. The max power consumpon of a single DC
channel is 12W when using the 5VDC seng and 15W when using the 12/18/24/48VDC sengs.
Voltage for each output channel can be adjusted and switched on/o via the front panel buons,
RS232 / IP commands or using the built in web GUI.
The DL-PSU8 can replace bulky power AC/DC power adapters and power strips with a universal power
soluon for DC powered AV, networking, security and IOT devices located in a rack system.
Product Overview
Package Contents
• DL-PSU8 8 Port DC Power Hub
• (1) Quick Install Guide
• (8) DC Power Cables (2-pin Terminal Block to DC)
• (1) RS232 Cable (DB9 to 3-pin Terminal Block)
• (2 each) US, UK, EU and AU Power Adapters
• (2) Rack Mounng Brackets
• (4) Plasc Cushions

DL-PSU8 Quick Guide
4
Front / Back Panel View
1. AC1 AC2 - Input AC Source Indicators
• When GREEN; AC input is powered on with normal output
• When RED; AC input is not powered
• When ORANGE - Input voltage is too low or too high
2. 01-08 (Front) - Output Selecon Buons; Press once to acvate / deacvate output selecons, long
press for 3 seconds to acvate / deacvate and lock the output selecon
3. 01-08 (Back) - DC Output Channels / Voltage Selector
• DC: 2 pin DC Phoenix power connector
• SELECT: Press switch to toggle output voltage selecon
• 5/12/18/24/48V: Voltage selecon LEDs
* When Solid; Corresponding voltage is selected for channel and working normally
* When Blinking Slowly; The channel is closed
* When Blinking Fast; Channel is short circuing or over voltage
4. RS232 - 3 pin Phoenix connector for RS232 system control
5. FW - USB A rmware update port
6. TCP/IP - RJ45 connector for Ethernet / GUI system control
7. AC1 AC2 - 2 AC input channels. Input voltage is AC100~240V.
8. Ground Pin - Ground device to earth
12
3 54 6 7 8

DL-PSU8 Quick Guide
5
WARNING: DO NOT EXCEED MAXIMUM
RATINGS
VOLTAGE POWER
(WATTS MAX)
MAX CURRENT PER
OUTPUT
5V DC 12W 2.4A
12V DC 15W 1.25A
18V DC 15W .83333A
24V DC 15W .625A
48V DC 15W .3125A
Voltage, Power, Current Per Output

DL-PSU8 Quick Guide
6
Cabling Wiring Requirements
Ethernet Control
The DL-PSU8 may be controlled via Ethernet using web browser for web server control or by using
telnet commands using port 4001. See owners manual online at www.libav.com for complete API.
The TCP/IP port requires a standard straight-through
Category 5 or greater cable with the TIA/EIA-568B crimp
paern for opmal operaon.
The default sengs for the TCP/IP port are:
IP address: 192.168.0.178
TIA/EIA-568B
Orange/White
Orange
Green/White
Blue
Blue/White
Green
Brown/White
Brown
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
1 8
Connect the Ethernet cable between the matrix and a
router with a straight-through cable or between the matrix
and a PC computer with a crossover cable. To connect to
the web server built into the DL-PSU8 type the default
IP address of the switcher into a browser on the PC. Be
sure the PC is in the same Network ID of the DL-PSU8 , ie
192.168.0/24.
RS232 Control
The RS232 connecon on the matrix is 3 pin
phoenix. See below for RS232 conguraon.
• 9600 baud
• 8 Data Bits
• 1 Stop Bit
• Parity = none
TX RX G
RX TX G
DL-PSU8
RS232 PORT
CONTROL
RS232
PINOUT
Connecng to
System Controller

DL-PSU8 Quick Guide
7
Technical Specicaons
Input/Output Connecons
Inputs Two (2) IEC 320 C13/C14 Male
Input Voltage 100~240VAC 50~60Hz
Outputs Eight (8) 2-Pin terminal block
Output Voltage 5V, 12V, 18V, 24V or 48V; selectable.
Maximum output power consumpon of
signal channel
5V:12W
12/18/24/48V:15W
Control
Ethernet 100BaseT
RS232 Baud Rate 9600bps
Chassis and Environmental
Enclosure Painted Aluminum
Dimensions (H x W x D) 44mm x 437mm x 357mm / 1.7” x 17.2” x 14”
Shipping Weight 5.2Kg / 11.5lb
Operang Temperature 0° to +50° C (+32° to +122° F)
Operang Humidity 10% to 90%, Non-condensing
Storage Temperature -20° to +70° C ( -4° to +140° F)
Storage Humidity 10% to 90%, Non-condensing
Power, ESD, and Regulatory
Power Supply 100V-240VAC / 50-60 Hz
Power Consumpon 178W (Max.)
Total DC Output Current 19.2A
Total DC Output Power 120W (Fully Loaded)
ESD Protecon 8kV air, 4kV contact
Product Regulatory FCC, CE, RoHS, UL
Other
Standard Warranty 5 years
Included Accessories (1) Quick Install Guide
(8) DC Power Cables (2-pin Terminal Block to DC)
(1) RS232 Cable (DB9 to 3-pin Terminal Block)
(2 each) US, UK, EU and AU Power Adapters
(2) Rack Mounng Brackets
(4) Plasc Cushions

Thank you for your purchase.
For Technical Support please call our toll free number at
800-530-8998 or email us at [e-mail]
www.libav.com
Digitalinx is a brand of:
11675 Ridgeline Drive
Colorado Springs, Colorado
80921 USA
Phone: [phone]
Fax: [phone]
Toll-Free: 800-530-8998