Liberty SAFELERT User manual

Your browser will now load a special
SAFELERT Setup Web Page.
Follow the onscreen instructions to
complete your SAFELERT Sensor setup.
6
Open an internet browser on your
computer, smartphone or tablet.
In the address bar type: 10.5.5.2 and press
Enter or Go.
5
It may show you an error indicating that
you do not have an internet connection.
This is normal.
Tip
Go to the wireless (Wi-Fi) settings of
your computer, smartphone or tablet.
Search for available wireless networks
and connect to the Wi-Fi network named Elertus.
4
The Elertus Wi-Fi network cannot provide an
internet connection, but will provide access to
the SAFELERT setup web page.
Setup
page
Wi-Fi
Wi-Fi
When the LED light on your SAFELERT
Sensor is flashing YELLOW it is in a
special setup mode. You can connect
to it just like you would your home or business
Wi-Fi network.
3
Wi-Fi Wi-Fi
Ensure that Wi-Fi is enabled on your computer,
smartphone or tablet, then continue.
Press and hold the little, white button
on the front of your SAFELERT Sensor
until the LED light flashes YELLOW.
2
You may need to hold the button down for
up to 15 seconds. The LED may blink other
colors before it begins flashing YELLOW.
Tip
Install the batteries into your
SAFELERT Sensor, and wait for the
LED light to turn solid RED.
1
A slot on the left side of the SAFELERT Sensor enables
you to pry the case open using a flathead screwdriver.
Tip
Before You Begin,
You Will Need
Your Liberty SAFELERT Sensor and the
included AA batteries.
A computer, smartphone or tablet with
Wi-Fi capability.
A flat-head screwdriver.
Your wireless (Wi-Fi) network name and
password. To make the setup easier, write
them in the space below:
Network Name: __________________________
Password: ________________________________
SAFELERT Setup Guide
POWERED BY

other normative documents:
EN60950, EN55022, EN55024
We hereby declare that the above named product is in conformity with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
The conformity assessment procedure referred to in Article 10(3) and detailed in Annex II
of Directive 1999/5/EC has been followed.
Industry Canada
IC: 3681C-ELRT10
This class B digital apparatus complies with Canadian ICES-003.
CET appareil numerique de la classe B est conforme a la norme NMB-003 du Canada’
Important Note: Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator and your body.
Note Importante: (Pour l’utilisation de dispositifs mobiles)
Declaration d’exposition aus radiations
Cet équipement est conforme aux limites d´exposition aux rayonnements IC établies pour
un environnement non contrôlé. Cet équipment doit être installé et utilisé avec un
mimimum de 20 cm de distance entre la source de rayonnement et votre corps.
Restriction of Hazardous Substances (RoHS)
All parts in the SAFELERT Sensor meet the material restrictions of RoHS, as proposed
by the RoHS Technical Adaptation Committee. This is based upon information provided
by suppliers of the raw materials used by Elertus to manufacture these products. As such,
Elertus makes no independent representations or warranties,
One-Year Limited Warranty
This product is warranted to be free of defects in material and workmanship for one year
from date of activation.
Elertus will, at its election and as the purchaser’s or end user’s sole and exclusive
remedy for any breach of the limited warranty set forth above, repair or replace this
product if a defect in material or workmanship is identified and communicated to Elertus
within the one-year period described above. Elertus is not responsible for removal or
reinstallation costs. This warranty is not valid in cases where damage to this product is
the result or arises out of misuse, abuse, incorrect repair or improper wiring or installation.
To notify Elertus of any breach of the foregoing limited warranty and to obtain warranty
service, contact Elertus Customer Support by e-mail to [email protected] or by calling
801-657-5352 x 1, to obtain a Return Materials Authorization (“RMA”) number and
instructions for returning your defective product to Elertus.
IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE EXPRESSLY DISCLAIMED, EXCEPT WHERE
SUCH DISCLAIMER IS PROHIBITED BY APPLICABLE LAW. ELERTUS AND/OR THE
SELLER DISCLAIM(S) ANY AND ALL LIABILITY FOR SPECIAL, INCIDENTAL AND
CONSEQUENTIAL DAMAGE IN ANY WAY ASSOCIATED WITH OR RELATED TO THE
PURCHASE, INSTALLATION AND/OR USE OF THIS
PRODUCT.
Some states/provinces do not allow limitations on how long an implied warranty lasts, or
the exclusion or limitation of special, incidental or consequential damages, so these
limitations and exclusions may not apply to you. This warranty gives you specific legal
rights. You may also have other rights which vary from state/province to state/province.
This is Elertus’ exclusive written warranty.
About This Document
Copyright © 2015, Elertus All rights reserved. Elertus is a trademark of Card Access
Products, LLC.
Other marks may be the property of their respective owners.
This device complies with Industry
Canada license-exempt RSS standard(s).
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must
accept any interference, including
interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux
CNR d’Industrie Canada applicables aux
appareils radio exempts de licence.
L’exploitation est autorisée aux deux
conditions suivantes: (1) l’appareil ne doit
pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si
le brouillage est susceptible d’en
compromettre le fonctionnement.
Specifications
Power Source:
Power Usage:
Temperature Range:
Humidity Range:
Dimensions (LxWxH):
Communications:
Regulatory Compliance
The SAFELERT Sensor complies with relevant standards established by the following
regulatory bodies: Federal Communications Commission (FCC), Conformité Européene
(CE), Industry Canada, and Restriction of Hazardous Substances (RoHS).
FCC
FCC ID: MHI-ELRT10
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communi-
cations. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Re-orient or relocate the SAFELERT Sensor.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT! Changes or modifications not expressly approved by Elertus void the user’s
authority to operate the equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
CE
We, Elertus, of 11778 South Election Road, Suite 260, Salt Lake City, Utah, 84020 USA,
declare under our sole responsibility that the product, the SAFELERT Sensor, Model Number
ELRT10, to which this declaration relates, is in conformity with the following standards and/or
Two (2) AA 1.5V alkaline batteries
1 year battery life with typical usage
-20°F to 150°F
0% to 90% (non-condensing)
3.1”(L) x 2.6”(W) x 1.05”(H) (78.7mm x 65.7mm x 26.6mm)
The SAFELERT Sensor operates as a client device using
industry-standard Wi-Fi® (8.2.11G)
QSG-LIB11
With the free apps for the iPhone®, iPad®, iPod®or Android™
devices you can customize your alerts, add or edit contacts, view the
most recent status and receive instant notifications.
Download them for free on the App Store or Google Play. You can
find them by scanning the QR codes below or by searching for
SafElert.
Get the Apps
Before you can Sign In to the smartphone app or the
Online Control Center you must complete the SAFELERT
Sensor setup and account activation. Please refer to the
first side of this manual for help with the setup.
Tip
Sign In
Click the button at the top of the
www.elertus.com website, then click on the Liberty SAFELERT
box
Go directly to libertysafe.elertus.com
In addition to the smartphone apps you can edit your SAFELERT
account from a computer browser. To access the online Control
Center you can:
Online Control Center
Contact Us
Support: 801.657.5352, x.1
Sales: 801.657.5352, x.2
[e-mail]
www.elertus.com/contact
libertysafe.elertus.com/support
If you do not receive alerts when the safe door is closed, you may
need to attach the external antenna (included). The optional antenna
can be installed anywhere on the exterior of your safe to extend the
range of your SAFELERT.
Installing the Antenna
(Note: If your safe has the round electrical outlet installed, there is a
SAFELERT port that you can use to route your antenna through to
the interior of your safe. You will need to feed the antenna cable
through the port prior to attaching to the unit.) To install the anten-
na, locate the connector on the upper left corner of your SAFELERT
Sensor’s cover. (See above). Press the antenna cable into the
connector until you hear a click. Attach the antenna to the desired
location on the outside of your safe. Antenna will be most effective if
placed as close to the top of the safe as possible and pointed in the
direction of your router.
*Antenna cable is 8.5 ft. in length
Adhere the sticky side of the Velcro strip to the flat surface on the
back of your SAFELERT Sensor. Adhere the other piece of Velcro to
the location where you want your SAFELERT Sensor installed.
Installing your Sensor
The SAFELERT Sensor can simply be placed on a shelf, counter or
anywhere else you want to monitor. You can also mount it using
the included Velcro strip.
What do the SAFELERT
LED lights mean?
Flashing YELLOW. Your SAFELERT Sensor is in Setup Mode.
It will remain in Setup Mode for up to 15 minutes.
What to do: Refer to Step 3 on the front of this guide to
setup your Elertus sevice.
Solid GREEN. You completed the setup and your SAFELERT
Sensor connected to the SAFELERT website successfully.
What to do: Nothing. You are done setting up your
SAFELERT Sensor. The LED will turn off within 30 minutes to
save batteries.
Solid RED. You completed the setup but your SAFELERT
Sensor was NOT able to connect to the SAFELERT website.
What to do: Ensure that you have the correct Name and
Password for your Wi-Fi network. Remove the batteries from
your SAFELERT Sensor, then start from Step 1 on the front of
this guide.