Life Fitness 93Ri User manual

95Ri, 93Ri, 90R
Recumbent Exercise Bikes
Assembly Instructions

Congratulations...
and welcome to the world of
The following Parts Identification Listing and the step by step assembly
procedures have been assembled to make the set-up of the Recumbent Exercise
Bikes as quick and easy as possible.
Please take special note of the following important points prior to choosing a
location and beginning assembly of the Recumbent Exercise Bikes.

IMPORTANT SAFETY INSTRUCTIONS!
⇒ DO NOT locate the Recumbent Exercise Bike outdoors, near swimming pools, or in areas of high
humidity.
⇒ DO NOT operate your Recumbent Exercise Bike if it has been dropped, damaged, or even partially
immersed in water. Contact Life Fitness Customer Support Services at the number in the Operation
Manual.
⇒ DO NOT locate the Recumbent Exercise Bike any closer than 30 inches (76 cm) to a television set.
⇒ DO NOT locate additional Recumbent Exercise Bike any closer than a minimum of 42 inches (107
cm) from center to center to avoid interference (cross talk) between Heart Rate monitors.
⇒ DO keep the area around your Recumbent Exercise Bike clear of any obstructions, including walls
and furniture.
⇒ DO verify the contents of the delivery carton against the accompanying Parts Listing prior to setting
the cartons and shipping material aside. If any parts are missing, contact Life Fitness Customer
Support Services at the number listed in the Operation Manual. Save the shipping cartons in case of
return.
⇒ DO read the entire Operation Manual prior to attempting to operate this machine as this is essential
for proper use.
⇒ NE PAS placer le vélo d’exercice allongé Lifecycle à l’extérieur, près d’une piscine ou dans un
endroit très humide.
⇒ NE PAS faire fonctionner le vélo d’exercice allongé Lifecycle s’il est tombé, s’il a été endommagé ou
s’il a été partiellement plongé dans l’eau. Téléphoner au service après-vente de Life Fitness dont le
numéro figure sur la couverture arrière du guide d’installation.
⇒ NE PAS placer le vélo d’exercice allongé Lifecycle à moins de 76 cm (30 po) d’un poste de
télévision.
⇒ MAINTENIR la zone autour du vélo d’exercice allongé Lifecycle libre de toute obstruction, y compris
murs et meubles.
⇒ VÉRIFIER si l’emballage contient toutes les pièces de la liste jointe avant de le mettre de côté. Si des
pièces manquent, téléphoner au service après-vente de Life Fitness dont le numéro figure sur la
couverture arrière du guide d’installation. Conserver l’emballage au cas où l’appareil devrait être
renvoyé.
⇒ LIRE le manuel de l’utilisateur tout entier avant d’essayer de faire fonctionner cet appareil. Ceci est
indispensable à son utilisation correcte.

T OOLS R EQUIRED FOR A SSEMBLY... Phillips screwdriver, 3/16" hex key wrench, T-40 Torx wrench
P ARTS D ESCRIPTION
1 Seat Back Screw Qty: 4 2 Seat Back Washer Qty: 4
3 Console Support Assembly Bolt Qty: 4 4 Console Screw Qty: 4
5 Seat Back Qty: 1 6 Console Support Assembly Qty: 1
7 Display Console Qty: 1 8 Accessory Tray Assembly Qty: 1
9 Left Pedal Strap Qty: 1 10 Right Pedal Strap Qty: 1
2
4
1
3
1” 2” 3” 4” 5”

Please read this prior to assembly.
This product is preconfigured to accept the addition of the Life Fitness Entertainment System. A
POWER CABLE and COAXIAL CABLE have been pre-installed. Please read both the product
assembly instructions and Entertainment Ready assembly instructions (included with the Life
Fitness Entertainment System) prior to assembly.
Route the POWER CABLE and COAXIAL CABLE alongside the MAIN WIRE HARNESS where
applicable.
7
8
5
2
1
64
3
9
10

1. Slide the ACCESSORY TRAY (#8) (if so equipped) over the
user right seat back post and down to make contact with the
SEAT HANDLEBAR.
2. Position the underside clamp bracket (A) around the SEAT
HANDLEBAR and tighten the two clamp SCREWS and
WASHERS (B).
NOTE: BE CAREFUL NOT TO OVER-TIGHTEN
THE SCREWS.
MISE EN GARDE : VEILLER À NE PAS TROP SERRER
LA VIS.
3. Align the four holes in the SEAT BACK (#5) with those in the
SEAT BACK POSTS. Insert the four SCREWS (#1) and
WASHERS (#2) through the backside of the SEAT BACK
POSTS and into the SEAT BACK. Tighten the four SCREWS
with a hex key wrench.
NOTE: BE CAREFUL NOT TO OVER-TIGHTEN
THE SCREWS.
MISE EN GARDE : VEILLER À NE PAS TROP SERRER
LA VIS.
4. Unfold the CONSOLE WIRE HARNESSES (C) from the POST
extending from the FRAME.
5. Feed the WIRE HARNESSES at the top of the FRAME POST
through the bottom of the CONSOLE SUPPORT ASSEMBLY
COLUMN. Continue pushing the WIRE HARNESSES until the
CONNECTORS at the end of the WIRE HARNESSES exit
through the opening at the top of the COLUMN. Gently pull the
WIRE HARNESSES to remove the slack.
6. Position the CONSOLE SUPPORT ASSEMBLY (#6) so that
the HANDLEBAR is facing the user and slide the CONSOLE
SUPPORT ASSEMBLY into the FRAME POST (D), being
careful not to pinch the WIRES in the process. Align the holes
in the top of the CONSOLE SUPPORT ASSEMBLY with those
in the FRAME POST. Install the four CONSOLE SUPPORT
ASSEMBLY BOLTS (#3) to secure it into position. Tighten the
four CONSOLE SUPPORT ASSEMBLY BOLTS to 15-20 ft.
lbs.
NOTE: BE VERY CAREFUL NOT TO DAMAGE THE WIRES
WHEN PASSING THE BOLTS THROUGH THE HOLES.
TIGHTEN THE BOLTS SECURELY.
MISE EN GARDE :FAITES ATTENTION TRÈS À NE PAS
ENDOMMAGER LES FILS EN PASSANT LES BOULONS
PAR LES TROUS. SERREZ LES BOULONS SOLIDEMENT.
7. Align the LOCKING TABS of the 10-PIN CONNECTOR and
the 4-PIN CONNECTOR and plug them together until they
SNAP into place.
8. Carefully feed the wires back into the top of the CONSOLE
SUPPORT ASSEMBLY (#6) and attach the DISPLAY
CONSOLE (#7) to the CONSOLE SUPPORT ASSEMBLY
using the four CONSOLE SCREWS (#4) and a Phillips
screwdriver. Tighten the four SCREWS in a criss-cross
pattern.
NOTE: BE CAREFUL NOT TO OVER-TIGHTEN
THE SCREWS.
MISE EN GARDE : VEILLER À NE PAS TROP SERRER LA
VIS.
4P
14P
4
6
D
7
C
3
5P
CX

9. After placing the exercise bike in the intended location for use,
check the stability of the bike. If the exercise bike is not level,
turn a LEVELER (G) in the rear STABILIZER BAR (H) in either
direction until the rocking motion is eliminated. Tighten the
JAM NUT (J) when the exercise bike is level.
NOTE: ONLY ONE LEVELER NEEDS TO BE TURNED.
REMARQUE : NE TOURNER QU’UN SEUL VÉRIN.
10. Locate the RIGHT PEDAL STRAP (#10) marked with an “R”.
Attach the RIGHT PEDAL STRAP to the RIGHT PEDAL (K)
with the double slot on the inward pedal strap tab looping
upward and attaching to the outward pedal strap tab. Repeat
for the LEFT PEDAL STRAP (#9) marked with an “L”.
Physical Dimensions:
95Ri 93Ri 90R
Length 54 inches / 137 centimeters 54 inches / 137 centimeters 54 inches / 137 centimeters
Width 26 inches / 66 centimeters 26 inches / 66 centimeters 26 inches / 66 centimeters
Height 51 inches / 129 centimeters 51 inches / 129 centimeters 51 inches / 129 centimeters
Weight 134 pounds / 61 kilograms 134 pounds / 61 kilograms 134 pounds / 61 kilograms
GJ
H

PRE-OPERATION CHECKLIST
 Ensure that the console support screws are tight.
 Make sure the Recumbent Exercise Bike is properly leveled and stable.
 Ensure that the Leveler Jam Nuts are tight.
 Read the entire Operation Manual before using the Recumbent Exercise Bike .
Before attempting to operate your Recumbent Exercise Bike, it is imperative that you familiarize yourself
with the contents of the Operation Manual. If your Recumbent Exercise Bike does not respond as
described in the OPERATION MANUAL, contact the nearest Life Fitness service center as listed in the
Operation Manual.
©2006 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness is trademark of Brunswick Corporation.
Polar is a registered trademark of Polar Electro, Inc. MO51-00K39-A140 11.06