Life Fitness 8115 User manual

8115 FLAT & INCLINE BENCH
Part # 6791801 Revision:7/20/981
ASSEMBLYINSTRUCTIONS

IMPORTANT NOTES
Please note:
Tools Required for Assembly
* Thank you for purchasing the LIFE FITNESS 8115 FLAT & INCLINE BENCH. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled on a
flat, level surface to assure its proper function.
2
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH RULER:
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your LIFE FITNESS customer service representa-
tive at [phone].
Bolt Length Ruler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
BOLT LENGTH
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
2. Do not allow minors or children to play on or around this equipment.
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
3. Exercise with care to avoid injury.
4. If unsure of proper use of equipment, call your local LIFE FITNESS STRENGTH distributor or
call the LIFE FITNESS STRENGTH customer service department at [phone].
* Rubber mallet or hammer
* 3/4” wrench, 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* Tape measure
5. Consult your physician before beginning any exercise program.

3
PARTS LIST
PART #
6651703
6700503
6712803
6697203
6624202
6624302
6651602
6780001
6780301
3202106
3202107
3102917
3102910
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
QTY
1
1
1
1
1
1
2
1
1
1
1
2
2
KEY
14
15
16
17
18
19
20
21
22
23
24
25
PART #
3202101
3102901
3102502
3102501
3102801
3102804
6406401
6619301
6653101
6412001
3120701
3118401
DESCRIPTION
1/2 X 1-1/4” BOLT
3/8 X 1-1/4” BOLT
1/2” WASHER
3/8” WASHER
1/2” LOCK NUT
1/2” LOW HEIGHT NUT
HINGETAB
U-PIN
1/2” SPACER
3/8” SPRING PIN
1/2” PAL NUT
4” VINYL CAP
QTY
2
4
6
6
5
3
2
1
1
1
1
1
DESCRIPTION
REAR UPRIGHT
BENCH FRAME
ADJUSTABLESLEEVE
BASETUBE
LEFT BACK PAD ANGLE
RIGHT BACK PAD ANGLE
2 X 15-1/2” PLATE
SEATPAD
BACK PAD
1/2 X 9-1/2” BOLT
1/2 X 6-1/2” BOLT
1/2 X 4” BOLT
1/2 X 3” BOLT
STEP 1:
FIGURE 1
• Assemble one U-PIN (21) to the BENCH FRAME (2) using one 1/2” SPACER (22) and one 1/2” PAL NUT (24) as shown in
FIGURE 1.
25
22 24
2
21
• Slide one 4” VINYL CAP (25) onto the U-PIN (21) as shown in FIGURE 1.

STEP 2:
FIGURE 2
• SECURELY assemble the 3/8” SPRING PIN (23) to the ADJUSTABLE SLEEVE (3) as shown in FIGURE 2.
4
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• Pull back the 3/8” SPRING PIN (23) on the ADJUSTABLE SLEEVE (3) and slide it over the end of the BENCH FRAME (2) as
shown in FIGURE 2. Slide the ADJUSTABLE SLEEVE (3) up to the first adjustment hole.
2
3
23

STEP 3:
FIGURE 3
5
• SECURELY assemble the REAR UPRIGHT (1) to the BENCH FRAME (2) using two 1/2 X 3” BOLTS (13), four 1/2” WASHERS
(16), and two 1/2” LOCK NUTS (18) as shown in FIGURE 3.
1/2 X 4” 12
13 1/2 X 3”
• SECURELYassemble the BASE TUBE (4) to the BENCH FRAME (2) using two 1/2 X 4” BOLTS (12) and two 1/2” LOCK NUTS
(18) as shown in FIGURE 3.
4
18
2
18
1
16

STEP 4:
FIGURE 4
6
• Assemble the LEFT & RIGHT BACK PAD ANGLES (5 & 6) and two HINGE TABS (20) to the BENCH FRAME (2) using one 1/2
X 9-1/2” BOLT (10) and one 1/2” LOW HEIGHT LOCK NUT (19). (NOTE: Tighten connection enough to remove play yet
allowing the parts to rotate freely.) See FIGURE 4.
0123456
1/2 1/2 1/2 1/2 1/2 1/2
1/2 X 9-1/2” 10
19 1/2” LOW
HEIGHT
6
2
20
5

7
STEP 5:
FIGURE 5
• Assemble the LEFT & RIGHT BACK PAD ANGLES (5 & 6) and two HINGE TABS (20) to the BENCH FRAME (2) using one 1/2
X 9-1/2” BOLT (10) and one 1/2” LOW HEIGHT LOCK NUT (19). (NOTE: Tighten connection enough to remove play yet
allowing the parts to rotate freely.) See FIGURE 4.
1/2 X 6-1/2”11
18
7
6
5 16
19
141/2 X 1-1/4”1/2”
LOW
HT.

8
FIGURE 6
STEP 6:
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• SECURELYassemble the BACK PAD(9) to theLEFT & RIGHTBACK PAD ANGLES(5 & 6)using four 3/8X 1-1/4” BOLTS (15) and
four 3/8”WASHERS (17) as shown in FIGURE 6.
3/8 X 1-1/4”15
9
5 6
17

STEP 7:
9
FIGURE 7
• SECURELYassemble the SEATPAD (8) to theHINGETABS (20) usingtwo3/8 X 1-1/4”BOLTS(15) and two3/8”WASHERS (17) as
shown in FIGURE 7.
3/8 X 1-1/4”15
17
8
20
Thank you for purchasing the LifeFitness 8115 FLAT & INCLINE BENCH. If unsure of proper use of
equipment,callyourlocalLifeFitness distributororcalltheLifeFitnesscustomerservicedepartmentat
[phone].
Thank you for purchasing the LifeFitness 8115 FLAT & INCLINE BENCH. If unsure of proper use of
equipment,callyourlocalLifeFitness distributororcalltheLifeFitnesscustomerservicedepartmentat
[phone].