Life Fitness SM61 User manual

M051-K50-A137 1
6 STACK MULTI-JUNGLE (SM61)
WITH 2 ADJUSTABLE PULLEYS
UNPACKING AND ASSEMBLY INSTRUCTIONS

SM61 Unpacking & Assembly Instructions
2
The SM61 comes partially assembled. Follow the steps below to complete the assembly.
WARNING: COMPONENTS OF THE SM61 ARE LARGE AND HEAVY. USE CAUTION
WHEN ASSEMBLING THIS MACHINE.
MATERIALS AND TOOLS REQUIRED FOR ASSEMBLY
1/2”, 3/8”, 5/8” & 9/16”
Socket wrench with
extension
1/8”
hex key wrench 5/8” & 9/16” Combination wrench Pinch bar
You will also need a ladder and a piano dolly to lift and position the weight stacks.
ASSEMBLY TIME
Two people can accomplish this assembly in approximately 2 hours.

SM61 Unpacking & Assembly Instructions
3
UNPACKING
Follow the steps below when unpacking the components of the SM61.
1. Cut off the shipping wrapper.
2. Remove the parts boxes and shipping boards.
3. Remove the items in the parts boxes. These items are shown in Figure 1.
A. Remove the bolts bag.
B. Remove the parts shown below. Parts that are used to build the SM61 are
described in the section HARDWARE at the end of these instructions.
Figure 1. Parts box contents (box 1 on left, box 2 on right).

SM61 Unpacking & Assembly Instructions
4
ASSEMBLY
Figure 2 shows an assembled SM61.
1
1
2
2
4
4
3
5
5
67
Figure 2. SM61 main components.
1. Cubes (2)
2. Lat bench (2)
3. Connecting beam (1)
4. Lat tops (2)
5. Tricep top (2)
6. 300 lb. Weight stacks (2)
7. 190 lb. Weight stacks (4)
1. Place the two weight “cubes” in their “final resting spots.” The cubes will be
approximately 11’4” apart as shown in Figure 3.

SM61 Unpacking & Assembly Instructions
5
Figure 3. Set the weight stack cubes.
2. Bolt on the teardrop pulleys above the lat benches (see Figure 4) on both cubes using
two 3/8” x 2-3/4” hex head bolts (used to bolt the cross beam to the cross members
and the adjustable pulley tops to the top beams). Include the 3/8” flat washer, end cap
washers, end caps and 3/8” Nyloc (locknut). Use the bolt configuration shown in
Figure 5. You may wish to use a pinch bar to align the bolt holes.
Figure 4. Bolt on the teardrop pulleys.

SM61 Unpacking & Assembly Instructions
6
Figure 5. Configuration for 2-3/4” and 3” bolts.
3. Using a 5/8” socket with extension and combination wrench, bolt on the connecting
beam to the cubes using two of the large 7/16” x 6” bolts, 7/16” washers, and 7/16”
nuts, end cap washers and end caps. Figure 6 shows the connected cubes.

SM61 Unpacking & Assembly Instructions
7
4. Using a 5/8” socket and combination wrench, mount the 56” lat tops (part T from
HARDWARE section) to the cells by inserting two of the large 7/16” by 6” bolts using
the hardware configuration shown in Figure 7. Mount the 29” tricep top (part U in
HARDWARE section) to the frame and connecting beam (See Figure 6). You will
need to remove the pulleys from the teardrop pulley assemblies to gain clearance for
the socket wrench extension. Leave the pulleys out of the housings until the cables
have been installed.
Figure 6. Mount lat tops and tricep tops.
Figure 7. Configuration for 6” bolts.

SM61 Unpacking & Assembly Instructions
8
150 lb.
weight stack
300 lb.
weight stack
150 lb.
weight stack
Figure 8. Mount rubber bumpers and the weight stacks.
5. Install the weight stacks. To do this:
A. Using a 9/16” socket and combination wrench, remove the tricep back rest bolts
(see Figure 9).
B. Using a 9/16” socket and combination wrench, unbolt the top plate and remove
the guide rods (see Figure 9).
Figure 9. Remove the tricep back rest, the top plate and the guide rods.

SM61 Unpacking & Assembly Instructions
9
C. Prepare the weight stack. Slide the guide rods (2) through the weight stacks (1)
as shown below. Place rubber bumpers (3) on the bottoms of each guide rod.
Make sure the pull pin (4) is in the bottom weight plate.
D. Flip over the weight stacks. When shipped, the weight stacks have the pull pins
facing upward. You will need to flip the stacks over so that the pull pins are facing
outward when they are loaded onto the machine. Since the pull pins will be facing
downward when they are flipped over, it is recommended that you put the stacks
on a padded carpet to keep the pins from being damaged.
E. Set the weight stacks onto the machine. Using a piano dolly, lift the weight
stacks over the bottom plate and set the stacks onto the rubber bumpers with the
plate numbers facing outward. The 300 lb weight stacks need to be facing the
“sides” of the cells (where the benches will be attached). The 190 lb weight
stacks will need to be facing the “outsides” and “insides” of the cells (where the
tricep pulley adjustable pulleys will be attached). Make sure the pull pins are
facing outward.
C. Prepare the weight stack-
add bumpers to bottom, insert
guide rods, put pull pin in
bottom stack. D. Flip over the weight stack
onto piano dolly. E. Hoist the weight
stack onto the machine.
F. With the top plate on the guide rods, bolt on the top plate to the top of the cells as
shown in Figure 10 using a 9/16” socket and combination wrench and the 3” bolts
(with cap washers) that were previously inserted.
Figure 10. Bolt on the top plate.
6. Using a 7/8” combination wrench, bolt the floating pulleys into the 190 lb weight
stacks (except for the tricep pushdown weight stacks- the one with the tricep back

SM61 Unpacking & Assembly Instructions
10
rest mounted to the frame as shown in Figure 9). You will need to remove the pulley
from the housing to thread the plug into the weight stack bayonet. Make sure the
9/16” jam nut is threaded 1-5/8” away from the pulley as shown in Figure 11. Leave
the pulleys out since you will need to have them out when the cable is routed.
Figure 11. Bolt the floating pulleys into the 190 lb weight stacks.
7. Mount adjustable pulley brackets. When shipped, the adjustable pulley brackets look
like the ones shown in Figure 12. The bolts need to be removed and the bracket
needs to be positioned so that the top of the bracket is in the top hole as shown by
the arrow in Figure 12. Use a 3” bolt with flat washers, end cap washers and end
caps. When you remove the bolts, leave the pulley bolt and pulley out since you will
need to thread the cable with the pulley removed.
Figure 12. Mount adjustable pulley bracket.
8. Mount the seated row and lat benches to the frame. Using the bolts specified in
Figure 13 and a 9/16” socket and combination wrenches, mount the benches as
shown in Figures 13 and 14.