Life Ionizer 7500 User manual

7500 User Manual

Safety Guide
Installation of Parts Guide
Production of Ionized Water
Operation Warnings
Operation Method
Indicator Functions
Installation Guide
Installation Instructions
Internal Filter Replacement
Filters
Explanation of Ionized Water
Alkaline and Acidic Water Usage Guide
Uses for Alkaline Ionized Water
Uses for Acidic Water
Performance Features
Common Problems and Solutions
Installation of the Pre-Filter
Acidic Cleaning Instructions
& Routine Maintenance
Frequently Asked Questions
4-8
10
11
12-13
14
15
16
17
18
19
20
21
22-23
24
25
26-27
28
29
30-41
Table of Contents

www.LifeIonizers.com/Support
4
Safety Guide - Read Completely
Before installation or operation of the LIFE IonizerTM, read this
instruction manual completely.
Note- Some parts may have been altered to improve product quality,
function or ease of use.
Symbols
Indications
Refer to the following key symbols and indicators throughout the manual.
Improper use may cause bodily injury
Improper use may cause structural damage to the unit
or physical injury
Improper use may cause serious injury or death
Caution, warning, danger symbol
Information on prohibited functions and uses
Make note of important information
Do not open as it may cause electric shock or other injury
Disconnect power plug in case of malfunction
75

www.LifeIonizers.com/Support 5
Improper use may cause bodily injury
Improper use may cause serious injury or death
When drinking Ionized Alkaline Water - Do not take
prescription or other medications for approximately
one hour before and after drinking water. Do not drink
Ionized Alkaline Water if you have been diagnosed with
Achlorhydria (low or no stomach acid).
This machine should not be repaired or otherwise
disassembled by any unauthorized person as it
may cause electrical re or shock, and will void the
manufacturer’s warranty.
Do not place the machine in humid areas such as
bathrooms. Do not clean this machine by spraying
the ionizer with water as it may cause electrical
shock.
75

www.LifeIonizers.com/Support
6
Improper use may cause serious injury or death
Power cord should not be touched with wet hands.
Power cord should be plugged directly into an electrical
outlet.
Do not connect multiple appliances into a single power
receptacle.
Dusty or dirty electrical outlets may cause safety issues.
Bending, twisting, pulling or putting heavy objects onto
the power cord may cause electrical problems including
re.
If power cord, plug, or electrical outlet are damaged,
discontinue use immediately.
If the ionizer machine falls into water-
1. Unplug power cord from electrical outlet
2. Wipe the machine down and place in shaded area
3. Contact your LIFE IonizerTM dealer
Use only (110v) in the U.S.A. and Mexico. Use (100v) in
Japan. Most other countries require (220v). The power
cord cannot be altered from manufacturer’s specs.
Do not crimp or staple the power cord as it could cause
electrical shock.
75

www.LifeIonizers.com/Support 7
Improper use may cause serious injury or death Improper use may cause bodily injury
Improper use may cause structural damage to
the unit or physical injury
Place machine in an upright position only.
If not used for several days, run water through the
unit for 1 to 3 minutes before starting.
Do not install this unit in direct sunlight or near a
heater, replace or other heat source.
Do not use water with a temperature of over 104
degrees Fahrenheit or 40 degrees Celcius.
Store Ionized Alkaline Water in an air-tight glass
container and refrigerate for up to 2 days.
If inexperienced with drinking Ionized Alkaline
Water, users are encouraged to start with lever 1.
DO NOT DRINK ACIDIC WATER.
If wall mounted, secure rmly and correctly.
Do not store Alkaline or Acidic water in metal
containers.
75

www.LifeIonizers.com/Support
8
Aluminum and brass containers will be tarnished by
Alkaline and acidic water.
Improper use may cause structural damage to the unit
or physical injury
Do not block the unit vent as it can cause overheating
and/or electrical problems.
Do not use benzene, thinner, or chemicals to clean the
unit as it can damage the housing.
Do not block the water passage or tubing.
If the machine will not be used for several days...
1. Unplug the power cord from the electrical outlet
2. Turn o the water valve to avoid leaking
3. Remove lters, drain and place in refrigerator in
plastic bags.
When handling the pH test (reagent drops)
1. Keep away from eye area. If eyes become irritated,
ush thoroughly and consult a doctor.
2. If accidentally swallowed, drink water and consult a
doctor.
3. Store in an airtight container away from the reach of
children.
4. Drops are ammable. Keep away from children.
75

www.LifeIonizers.com/Support 975

www.LifeIonizers.com/Support
10
1. Refer to the diagrams on the following page before beginning
installation.
2. Be aware that a 110v outlet (USA) or 220v outlet is required. If
the outlet is located under the sink, make sure it is not near
the water source.
3. If after installation the water has an odor, you may need to
install a pre-lter. Please consult your LIFE IonizerTM dealer.
4. How to use reagent drops. (BTB Chemical). Put 2-3 drops in
approximately 1 ounce of water to be tested. Compare color
to color chart provided in kit to determine pH level.
EXTRA
FUSE
Reagent Drops
(pH Test Drops)
Flexible Hose
Wall - Mount Nail Tubing Hose
Diverter User Manual
BTB Chemical
Installation of Parts Guide
75

www.LifeIonizers.com/Support 11
1. Press the main water ow
button on top of the product.
2. Select the water type –
Alkaline, Acidic, or Puried
setting.
3. When the “Alkaline” is selected,
the LCD indicates the Alkaline
setting and level.
When you select the main
water ow button while the
water pressure is low or valve
is closed, the LCD will appear as
“Fig. 1” Please check the water
pressure or valve opening before
proceeding.
4. According to the selected step,
the LED indicates the pH of the
water.
“ERR 1” will appear as shown in Fig. 1 if water pressure is low.
Please check...
Production of Ionized Water
75

www.LifeIonizers.com/Support
12
Parts for the Ionizer (Front)
1. Water Spout
2. Water Hose
3. Flexible Hose
Connector
4. Control Panel
5. LCD panel
DO NOT run the following types of water though the LIFE
IonizerTM as it can cause damage to the unit.
1. Dirty or Salty Water
2. Water containing high amounts of rust or iron
3. Water above 40 degrees C or 104 degrees F
Read these instructions thoroughly before attempting
installation.
Operation Warnings
75

www.LifeIonizers.com/Support 13
345
1. First Filter Cover
2. Wall Mount Screw
Holes
3. Speaker
4. Bar Code and Serial
Number
5. Second Filter
1. Outlet valve
2. Inlet valve
3. Power Plug
4. Fuse Box
5. On/O Power Switch
Parts for the Ionizer (Back)
Parts for the Ionizer (Bottom)
75

www.LifeIonizers.com/Support
14
When “CLEAN WATER” is
selected, pH is not indicated.
The “ALKL” and “ACID” LEDs
go o.
When “Alkaline” water is
chosen, Levels 1 to 4 can be
selected by pressing the
“Alkaline” button again.
When “ACID WATER” is
selected, Level 1 or 2 can
be selected by pressing the
“ACID WATER” button again.
When “FUNCTION” is selected,
The menu changes from the
main menu to FN1 and FN2 and
then back to the main menu.
When replacing the lter while
on the main menu, press the“1ST
FILTER”or“2ND FILTER”button
and hold for 5 sec. This resets the
lter counter to 0000. The lter
count goes to 9999.
When FN2 is selected with the
“FUNCTION”button, the amperage
setting can be adjusted from 0
to 4 by pressing the ”2ND FIL-
TER” (increase) and “1ST FILTER”
(decrease) buttons.
FN1 is the volume menu.
Levels 0 to 4 can be selected
by pressing the ”2ND FILTER”
(up) and “1ST FILTER” (down)
buttons to increase or decrease
the volume.
Operation Method
75

www.LifeIonizers.com/Support 15
Water Cleaning
Voice Functions
Ionized Alkaline Water
Acid Water Button
Puried Water Button
1. Drinking method indicator
2. pH indicator
3. Indicates “Being Washed”
4. Rotates while cleaning
5. Indicates ion water type
(Alkaline, acidic, puried)
6. Indicates selected
ionization water setting
7. Filter life - indicator
8. LIFE IonizerTM Logo
*Please wait a few seconds… as the machine is cleaning itself.
*4th grade of Ionized Alkaline Water is being extracted now.
*3rd grade of Ionized Alkaline Water is being extracted now.
*2nd grade of Ionized Alkaline Water is being extracted now.
*1st grade of Ionized Alkaline Water is being extracted now.
*2nd grade of acid water is being extracted now.
*1st grade of acid water is being extracted now.
*1st grade of clean water is being extracted now.
Voice: Please wait a few seconds as the machine is cleaning itself.
Indicator Functions
75

www.LifeIonizers.com/Support
16
C
o
ld
w
a
t
e
r
in
le
t
C
o
ld
w
a
t
e
r
i
n
l
e
t
Assembly method of valve for
wall-mounted water taps
Fix adapter
Quarter turn
for Tap Water
Running
Water
Rubber Gasket
Remove the aerator from the water tap.
Assembly method of valve for Deck-sink water taps
Screw in the adaptor
Remove the aerator from
the water tap.
Connect by rotation
after insertion of rubber
packing
Installation Guide
Cold Water inlet
Assembly method of valve for Deck sink water taps
Assembly method of valve for
wall-mounted water taps
Quarter turn
for Tap Water
Running
Water
Cold Water inlet
Rubber Gasket
Fix adapter
(Alkaline)
(Wash)
75

www.LifeIonizers.com/Support 17
Installation Guide Installation Instructions for LIFE IonizerTM 7500
Use Cold Water Only With Your Ionizer
STEP 1: Unscrew the existing aerator from your faucet.
STEP 2: Use teon plumbers tape on the threads. Screw the LIFE
IonizerTM diverter valve onto your faucet. Three dierent
sized adaptors are included for non-standard sized faucets.
STEP 3: Unscrew the round nut from the side of the diverter valve.
Slide the nut over the end of the 1/4” tubing and then screw
the nut back onto the diverter valve. Tubing should now t
snugly onto the diverter valve.
STEP 4: Lay the ionizer down on its back and you will see two white
elbows extruding from the bottom of the machine. There
will be an o-white collar around the base of the elbow.
Depress the collar towards the machine while simultaneously
extracting the elbow from the machine. Now, holding the
elbow in your hands, you’ll see a similar collar near the end
of the elbow. In the same way as you extracted the elbow,
you can depress the collar towards the elbow and extract
the plug from the end of the elbow. It is sometimes helpful
to use the back of a butter knife or screw driver to remove
the plug. If you ever need to remove the tubing from the
quick release, you will use the same process.
STEP 5: Run tubing from the diverter valve to the inlet valve on the
bottom of the ionizer. Be sure to push the tubing into the
quick connect valve 3/4” until it is rmly seated.
STEP 6: Insert one end of tubing into outlet valve on bottom of unit
and run the other end into the sink securing it with the
suction cup provided. Some units may contain water.
Don’t be alarmed; we test units for quality before shipment!
75

www.LifeIonizers.com/Support
18
Internal Filter Replacement
1. Press the top and
bottom of the lter
cover.
2. Open the lter cover
following the direction
of the arrow.
3. Turn the lter top in
the arrow direction.
6. Reset the new lter
button on the ionizer.
5. Insert the new lter
following the direction
of the installation arrow
and turn the lter
bases appropriately.
4. Lift the lter up and
out following the
direction of the arrow.
Tips After Filter Replacement:
1) Select the “Puried Water” setting and let the water run for 3-5 minutes after any
lter replacement .
2) If the machine has not been used for a few days, let the water run for 3-5 minutes
at the “Puried Water” setting before making Ionized Alkaline water for consumption.
3) Consult with the installer or retailer on the purchase of lters if in question about
usage or installation.
75

www.LifeIonizers.com/Support 19
Tips After Filter Replacement:
1) Select the “Puried Water” setting and let the water run for 3-5 minutes after any
lter replacement .
2) If the machine has not been used for a few days, let the water run for 3-5 minutes
at the “Puried Water” setting before making Ionized Alkaline water for consumption.
3) Consult with the installer or retailer on the purchase of lters if in question about
usage or installation.
Filters
1. Sediment
Eliminates sediments (mud, rust, sand, etc) 10 microns or
larger.
2. Pre-Carbon
Absorbs and eliminates various compounds, remaining
chlorine, taste and odor, THM, etc.
3. Activated Carbon Filters
Ultra-ne coconut shell carbon and silver impregnated
carbon.
4. Final Stage Sediment Filter
Reduces lter remnants and remaining sediments.
1. Granule type Carbon Filter
Reduces chlorine taste and odors, fast absorbing, generates
low dust.
2. Pi-Ceramic Negative Ion Filter
Generates negative ions, making water clusters smaller.
3. BioMass ball-Ceramic Filter - High quality ceramic lter
designed for bacteria control.
4. Calcium Powder with Ultra Membrane
Transforms structure to hexagonal water.
5. Special Quality Sediment Filter
Prevents sediment discharge.
75

www.LifeIonizers.com/Support
20
anode cathode
With electrolyzed water, the cathode (-) produces Alkaline Ionized Water
with minerals (pH scope 7.5~10) - such as Ca, K, Mg, Na, etc. because of
the hydroxyl ion (OH-) generating reaction.
The anode (+) has lots of hydrogen (H+) (pH scope 3.5~6.5) because
the oxygen gas (O2) generates a reaction and acid ion water has many
ions such as Cl, S, P.
The Ionized Alkaline Water and acid ion water made by an electrolytic
reduction water generator, has characteristics like those below.
Explanation of Ionized Water
75