Lifetime POWER LIFT Quick start guide

Lifetime’s assembly experts offer quick responses and great customer service.
POWER LIFT®
BASKETBALL SYSTEM
Icon Legend................................2
Notices....................................3
Ground Preparation.....................4
Pole Assembly.............................9
Backboard to Rim Assembly.......14
Backboard to Pole Assembly......20
Parts Identifier..........................i-iv
Handle Assembly.......................29
Final Assembly..........................36
Maintenance Instructions..........43
Registration...........................43
Warning Sticker........................44
Warranty................................47
Call: 1-800-225-3865
7:00 am–5:00 pm (Monday–Friday) MST
and 9:00 am–1:00 pm Saturday MST
Web: www.lifetime.com/instructions
Live Chat: www.lifetime.com/instructions
NEED HELP? TALK TO US!
MODEL# AND PRODUCT ID (you will need both when contacting us)
Model Number: Product ID:
Lifetime basketball systems are designed to be
strong and durable. We strive to make assembly as
easy as possible without compromising quality. If
you get stuck, we have tools to help:
•Prepare the Area
Before you start, you will need at least six 80-lb.
bags of concrete mix. Before digging, call to locate
any buried utility lines.
•Recruit Friends and Family
Assembly should take 3 people about 3–4
hours to complete.
Save this instruction in the event that the manufacturer
has to be contacted for replacement parts.
TOOLS REQUIRED TABLE OF CONTENTS
90698
(2) (2) (2)
(1)
(1)
(1) (1)
3/4” (19 mm) 11/16” (18 mm) 9/16” (14 mm)
(1)
(1)
(1)
(2)
1/2” (13 mm)
(1)
Cement
6-90-lb. bags
(1)
30” (762 mm)
Rebar
(1) (1)
COPY

2
• Indicates the parts to be used for a section.
• Indicates special heed should be taken when reading.
• Indicates the hardware to be used for a section.
• Indicates the tools to be used for a section.
• Indicates no hardware required for a specific page.
• Indicates no parts required for a specific section.
• Indicates to use/not to use an electric drill for a specific step.
ICON LEGEND
• Indicates the use of a Centerlock Nut. A Nut with this marking will require some effort to tighten. This
hardware was designed with this feature in order to prevent loosening later.
• Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
CONTACT US
www.lifetime.com/instructions
Call: 1-800-225-3865
7:00 am–5:00 pm (Monday–Friday) MST
and 9:00 am–1:00 pm Saturday MST
1172647 C 2/25/2016
COPY

3
WARNINGS & NOTICES / AVERTISSEMENTS ET AVIS / ADVERTENCIAS Y AVISOS
Most injuries are caused by misuse and/or not following instructions. Use caution when using this product.
To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing
material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware
identifier and parts list in this document. Proper and complete assembly, use and supervision are essential for proper operatation and to reduce the
risk of accident or injury. A high probability of serious injury exists if this product is not installed, maintained, and operated properly.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
• If using a ladder during assembly, use extreme caution.
• Two capable adults are recommended for this operation.
• Check base daily for leakage. Leaks will cause system to fall.
• Assemble the pole sections properly. Failure to do so could cause the pole sections to separate during play or transport.
• Minimum operational height is 6 ft 6 in (1.98m) to the bottom of the backboard.
SAFETY INSTRUCTIONS
WARNINGS & NOTICES

4
1GROUND PREPARATION
Metal Parts
TOOLS REQUIRED
PARTS REQUIRED
HARDWARE REQUIRED
(1)
(1)
ALE (x1)
30” Rebar
Cement Mix
Level
BGW (x1)
Paper Parts
(1)

5
TOOLS AND HARDWARE REQUIRED
XSECTION 1 (CONTINUED)
1.1
• A Ground Sleeve is available as an
alternative to cementing the Pole into the
ground. Please contact Customer Service for
more information.
!
• Dig a round hole 24” deep and 21” in diameter. If you live in an area where frost heaves may pose a problem,
consult your local building inspector to determine the proper hole depth. The edge of the hole should be flush
with the edge of the playing surface.

6
TOOLS AND HARDWARE REQUIRED
XSECTION 1 (CONTINUED)
• Make a mark 16 inches from the dimpled end of the Bottom Pole (ALE) (do not scratch the powder coating). Slide
the Alignment Frame (BGW) over the Bottom Pole.
• Mix 5 1/2 bags of concrete. Save 1/2 bag of concrete mix to use later in the assembly. Pour the mixed
concrete into the hole until it is filled to the level of the playing surface.
1.2
1.3
(9 Bags, 80 lb each)
ALE
16”
ALE
BGW

7
TOOLS AND HARDWARE REQUIRED
XSECTION 1 (CONTINUED)
• Slide the dimpled end of the Bottom Pole (ALE) into the cement up to the 16-inch mark. Position the pole next to
the playing surface. For regulation courts, the Alignment Frame (BGW) should cross the playing surface at the middle
of the scored measurements.
1.4
• Use a Level to make sure the Bottom Pole is standing vertical. Form
the cement into a downward slope away from the pole to allow water
runoff. Failure to do so may result in premature rusting of the Pole.
• If the pole is buried too deep or too shallow,
the rim will not to be at the correct height.
• Do not continue the assembly until the concrete
has been allowed to set for 1-4 hours.
!
!
!
30” Rebar
Playing
Surface
ALE
TOP VIEW
BGW
ALE
Rebar
• Insert the 30” rebar (not included) inside the Bottom Pole (ALE) so it is about 15” from the top of the pole. Check
the pole several times within the first hour to make sure that all sides are vertical and that the 16-inch mark remains level with the
surface.
1.5

8
TOOLS AND HARDWARE REQUIRED
XSECTION 1 (CONTINUED)
• Mix the remaining 1/2 bag of concrete. Fill the Bottom Pole (ALE) with concrete until it reaches the top of the
rebar (about 15” from the top of the pole). Tamp the concrete down in the Bottom Pole with a broom handle to
remove air pockets. Clean all concrete off the outside of the pole. You may now remove the Alignment Frame (BGW).
1.6
15”
• Stop assembly now. Do not continue the assembly until the concrete has been allowed
to set for at least 72 hours (3 days). In humid climates or wet weather, allow more time
for the concrete to cure. Do not proceed until the curing process is complete.
!

9
2POLE ASSEMBLY
Metal Parts
Hardware Bag
TOOLS REQUIRED
PARTS REQUIRED
HARDWARE REQUIRED
ALF (x1)
CMV (x2)
AAA (x2) AAF (x2)
ANF (x2)
ANE (x2)
5”
(Not actual length)
ALL (x1)
ALH (x1)
ALM (x1)
BCO

10
TOOLS AND HARDWARE REQUIRED
XSECTION 2 (CONTINUED)
AAF (x2)
ANF (x2)
ANE (x2)
5”
(Not actual length)
2.1
ANF
AAF
ANE
Large holes
Small holes
ALH
• After allowing the concrete to cure for at least 72 hours, insert the Hex Bolts (ANF) with the Washers (AAF) into
the Top Pole (ALH) as shown. Then slide the Spacers (ANE) onto the Hex Bolts.