liftup REMOTE2 User manual

Liftup Inc. | 4809 Ehrlich Road | Suite 105 | FL –33624, Tampa | T: [phone] | M: [email protected] | www.liftup.us
User Manual
REMOTE2
USER MANUAL –REMOTE2 –US VERSION 1.0

2
Liftup Inc. | 4809 Ehrlich Road | Suite 105 | FL –33624, Tampa | T: [phone] | M: [email protected] | www.liftup.us
———————————— USER MANUAL –REMOTE2 –US VERSION 1.0
Content
1. Foreword...................................................................................................................................................3
2. Declaration ...............................................................................................................................................3
2.1 Regulatory Approvals........................................................................................................................6
2.2 EU Declaration of conformity.........................................................................................................8
3. Technical specifications:.........................................................................................................................9
3.1 Remote control ..................................................................................................................................9
4. Configuration..........................................................................................................................................10
4.1 Battery: ...............................................................................................................................................11
4.2 Pairing of remote control ..............................................................................................................12
5. Disposal ...................................................................................................................................................13
6. Right of warranty...................................................................................................................................13
7. Approvals and certificates ...................................................................................................................13

Liftup Inc. | 4809 Ehrlich Road | Suite 105 | FL –33624, Tampa | T: [phone] | M: [e-mail] | www.liftup.us
———————————— USER MANUAL –REMOTE2 –US VERSION 1.0
3
1. Foreword
Congratulations on purchasing your new Remote.
It is important to read this manual before using the “REMOTE2”.
This is an original user manual for the “REMOTE2”.
Usage:
The REMOTE2 is intended for daily use together with other
Liftup products, e.g. FlexStep V2, which is operated by means of
operating panels at the upper and lower levels respectively, push-
buttons on the platform, or by using the remote control (supple-
mentary equipment).
The lift is a so-called “dead man operated” lift, i.e. the buttons
must be pressed and held during the entire motion. Also called
“Hold to run operated”. This feature is implemented for safety
reasons.
2. Declaration
Corporate Office:
Manufacture:
Liftup Inc.
4809 Ehrlich Road
Suite 105
FL –33624, Tampa
Phone: [phone]
www.liftup.us
Liftup A/S
Hagensvej 21
DK–9530 Stoevring
Denmark
Phone: [phone]
www.liftup.dk
Copyright and Trademarks
© Liftup A/S. All rights reserved.
Liftup, the Liftup logo and Liftup are trademarks of Liftup A/S, registered in the United States
and in other countries. All other trademarks are the property of their respective owners.
Release Notice
This document is release 1.0 of the REMOTE2 User Manual.
The following Product Limited Warranty gives Resellers specific legal rights. You may have
others, which vary from state/jurisdiction to state/jurisdiction.

4
Liftup Inc. | 4809 Ehrlich Road | Suite 105 | FL –33624, Tampa | T: [phone] | M: [email protected] | www.liftup.us
———————————— USER MANUAL –REMOTE2 –US VERSION 1.0
Product Limited Warranty
Subject to the terms and conditions set forth herein, Liftup A/S (“Liftup”) makes the following
warranty only to its Resellers who purchase the REMOTE2 hardware product (“Product”)
directly from Liftup: for a period of one (1) year from the date of shipment from Liftup, the
Product will substantially conform to Liftup’s standard published specifications for the Product
and the Product hardware will be substantially free from defects in materials and workmanship.
The foregoing warranty shall not apply to embedded software/firmware components.
THIS PRODUCT LIMITED WARRANTY IS PROVIDED TO RESELLERS AND TO RESELLERS
ONLY. RESELLER IS SOLELY RESPONSIBLE FOR ANY AND ALL WARRANTIES MADE TO
ITS CUSTOMERS, AND LIFTUP MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND
SHALL HAVE NO OBLIGATIONS OR LIABILITY TO RESELLER’S CUSTOMERS OR END-
USERS OF THE PRODUCT. RESELLER SHALL NOT MAKE ANY REPRESENTATIONS OR
WARRANTIES ON LIFTUP’S BEHALF, AND SHALL FULLY INDEMNIFY, DEFEND AND
HOLD LIFTUP HARMLESS FROM ANY BREACH OF THE FOREGOING. IF RESELLER
DISTRIBUTES PRODUCT TO END-USER CUSTOMERS, RESELLER SHALL BE SOLELY
RESPONSIBLE FOR PREPARING AND PROVIDING PRODUCT WARRANTIES AND
PRODUCT LITERATURE TO END-USERS.
Warranty Remedies
If the Product fails during the warranty period for reasons covered by this Product Limited
Warranty and Reseller notifies Liftup of such failure during the warranty period, Liftup at is
option will repair OR replace the nonconforming Product, OR refund the purchase price pai
by Reseller for the Product, provided that Reseller returns the Product to Liftup in accordance
with Liftup’s standard return material authorization procedures or as otherwise instructed by
Liftup.
Warranty Exclusions and Disclaimers
The foregoing Product Limited Warranty shall only apply in the event and to the extent that (i)
the Product is properly and correctly installed, configured, interfaced, maintained, stored and
operated in accordance with Liftup’s specifications, and (ii) the Product is not modified or
misused. This Product Limited Warranty shall not apply to, and Liftup shall not be responsible
for, defects or performance problems resulting from: (a) the combination or utilization of the
Product with hardware or software products, information, data, systems, interfaces, services or
devices not made, supplied or specified by Liftup; (b) the operation of the Product under any
specifications other than, or in addition to, Liftup’s standard published specifications for the
Product; (c) the unauthorized installation, modification or use of the Product; (d) damage caused
by: accident, lightning or other electrical discharge, water immersion or spray, or exposure to
environmental conditions for which the Product is not intended; or (e) normal wear and tear
on consumable parts, including by way of example and without limitation, batteries.
LIFTUP DOES NOT WARRANT OR GUARANTEE THE RESULTS OBTAINED THROUGH
THE USE OF THE PRODUCT. THE FOREGOING TERMS OF THE PRODUCT LIMITED
WARRANTY STATE LIFTUP’S ENTIRE LIABILITY, AND RESELLER’S EXCLUSIVE REMEDIES,
RELATING TO THE USE AND PERFORMANCE OF THE PRODUCT EXCEPT AS
OTHERWISE EXPRESSLY PROVIDED FOR IN THIS PRODUCT LIMITED WARRANTY, THE
PRODUCT, ACCOMPANYING DOCUMENTATION AND MATERIALS, AND/OR ANY
EMBEDDED SOFTWARE/FIRMWARE AND UPDATES THERETO ARE PROVIDED “AS-IS”

Liftup Inc. | 4809 Ehrlich Road | Suite 105 | FL –33624, Tampa | T: [phone] | M: [e-mail] | www.liftup.us
———————————— USER MANUAL –REMOTE2 –US VERSION 1.0
5
AND WITHOUT EXPRESS OR IMPLIED WARRANTIES OF ANY KIND, BY EITHER LIFTUP
OR ANYONE WHO HAS BEEN INVOLVED IN ITS CREATION, PRODUCTION,
INSTALLATION OR DISTRIBUTION, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
TITLE AND NONINFRINGEMENT. THE STATED EXPRESS WARRANTIES ARE IN LIEU OF
ALL OBLIGATIONS OR LIABILITIES ON THE PART OF LIFTUP ARISING OUT OF, OR IN
CONNECTION WITH, THE PRODUCT. WITHOUT LIMITING THE GENERALITY OF THE
FOREGOING:
THE PRODUCT MAY CONTAIN TECHNOLOGY THAT IS NOT FAULT TOLERANT AND
IS NOT DESIGNED, MANUFACTURED OR INTENDED FOR USE IN ENVIRONMENTS OR
APPLICATIONS IN WHICH THE FAILURE OF THE PRODUCT WOULD LEAD TO DEATH,
PERSONAL INJURY OR SEVERE PHYSICAL OR ENVIRONMENTAL DAMAGE OR SEVERE
FINANCIAL LOSS. ANY USE OR DISTRIBUTION BY RESELLER OR ITS CUSTOMERS IN
CONNECTION WITH ANY SUCH ENVIRONMENT OR APPLICATION SHALL BE AT
RESELLER’S AND ITS CUSTOMERS’ SOLE RISK, AND LIFTUP SHALL HAVE NO LIABILITY
WHATSOEVER IN CONNECTION THEREWITH. RESELLER SHALL INDEMNIFY AND
HOLD LIFTUP AND ITS SUPPLIERS HARMLESS FROM ANY CLAIM BROUGHT AGAINST
LIFTUP WHICH ARISES FROM RESELLER’S USE OR DISTRIBUTION OF THE PRODUCT IN
CONNECTION WITH SUCH ENVIVRONMENTS OR APPLICATIONS. SOME STATES AND
JURISDICTIONS DO NOT ALLOW LIMITATIONS ON DURATION OR THE EXCLUSION
OF AN IMPLIED WARRANTY, SO CERTAIN OF THE ABOVE LIMITATIONS MAY NOT
APPLY TO EVERY RESELLER.
Embedded Software/Firmware
The Product and associated tools, if any, may contain embedded software/firmware, which is
licensed, not sold, and is only for use within the Product as an integral part thereof. Such
embedded software/firmware (which includes all updates thereto) contains valuable trade
secrets and is proprietary to Liftup and its suppliers. To the greatest extent permitted by law,
such embedded software/firmware may not be modified, copied, disassembled, decompiled or
reverse engineered. Liftup reserves all other rights.
Limitation of Liability
LIFTUP’S ENTIRE LIABILITY REGARDING THE PRODUCT SHALL BE LIMITED TO THE
AMOUNT ACTUALLY PAID BY RESELLER FOR THE PRODUCT. TO THE MAXIMUM
EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL LIFTUP OR ITS
SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES WHATSOEVER UNDER ANY CIRCUMSTANCE OR LEGAL THEORY
RELATING IN ANY WAY TO THE PRODUCTS, ACCOMPANYING DOCUMENTATION
AND MATERIALS, AND ANY EMBEDDED SOFTWARE/FIRMWARE AND UPDATES
THERETO (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS
PROFITS,
BUSINESS INTERRUPTION, LOSS OF DATA OR ANY OTHER PECUNIARY LOSS),
REGARDLESS OF WHETHER LIFTUP HAS BEEN ADVISED OF THE POSSIBILITY OF ANY
SUCH LOSS AND REGARDLESS OF THE COURSE OF DEALING BETWEEN LIFTUP AND
RESELLER. BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW THE

6
Liftup Inc. | 4809 Ehrlich Road | Suite 105 | FL –33624, Tampa | T: [phone] | M: [email protected] | www.liftup.us
———————————— USER MANUAL –REMOTE2 –US VERSION 1.0
EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO EVERY RESELLER.
Notices
Class B Statement –Notice to Users. This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communication. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Consult the dealer or an experienced radio/TV technician for help.
Changes and modifications not expressly approved by the manufacturer or registrant of this
equipment can void your authority to operate this equipment under Federal Communications
Commission rules.
2.1 Regulatory Approvals
CE
The REMOTE2 product comply with the essential requirements of the RED Directive
2014/53/EU as stated by the EU Declaration of Conformity (CE). The REMOTE2 product
comply with the European Telecommunications Standards Institute Specifications EN 300 440
operating in 2.400 GHz to 2.483 GHz band for Radio Equipment and Systems
EU/International
The REMOTE2 complies with the essential requirements of the 2011/65/EU directive on the
restriction of the use of certain hazardous substances in electrical and electronic equipment
(ROHS 2).
Complies with the essential requirements of the EU 1907/2006 regulation concerning the
Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH).
Complies with the requirements of the 2012/19/EU directive on waste electrical and electronic
equipment and directive 2006/66/EC on batteries and accumulators and waste batteries and
accumulators (WEEE).

Liftup Inc. | 4809 Ehrlich Road | Suite 105 | FL –33624, Tampa | T: [phone] | M: [e-mail] | www.liftup.us
———————————— USER MANUAL –REMOTE2 –US VERSION 1.0
7
FCC/IC
The REMOTE2 product comply with the FCC Part 15.249 and the Industry Canada require-
ments RSS-GEN, RSS-210
The REMOTE2 product complies with Part 15 of the FCC rules and with Industry Canada license
exempt standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
The REMOTE2 product is SAR test excluded according to FCC KDB 447498, RSS102 and EN
62479 at separation distances larger than 5 mm and less than 50 mm.
With respect to radiofrequency radiation exposure Information, it is declared; that this
equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This gives an extra margin, since the remote control normally, only is used in
“controlled environment” for approx. 30 seconds when lifting, and typically only a few times a
day.
REMOTE2
FCC ID:
2AK8H-REMOTE2
IC-ID:
22516-REMOTE2
ACMA (AUS/NZ)
The REMOTE2 product complies with the Australian/New Zealand Radio communication Act
2400-2483 MHz.

8
Liftup Inc. | 4809 Ehrlich Road | Suite 105 | FL –33624, Tampa | T: [phone] | M: [email protected] | www.liftup.us
———————————— USER MANUAL –REMOTE2 –US VERSION 1.0
2.2 EU Declaration of conformity
Manufacturer: Liftup A/S
Address: Hagensvej 21, DK-9530 Støvring, Tel. [phone]
Hereby declares that: REMOTE2 used together with other Liftup equipment is in com-
pliance with:
_____________________________________________________________________________________
EMC Directive 2014/30/EU
ROHS-Directive: 2011/65/EU. substances in electronic equipment
RED 2014/53/EU, Radio Equipment Directive
FCC (USA) CFR 47 Part 15 FCC ID: 2AK8H-REMOTE2
ISED (Industry Canada) RSS-210 IC-ID: 22516-REMOTE2
_____________________________________________________________________________________
REMOTE2 meets the relevant requirements notably in following standards:
EN 60601-1-2: 2015 EMC of Medical Electrical Equipment
EN 60601-1-11:2015 Home Care
CISPR 11, Class B: 2016 Emission
EN 61000-4-2:2009 ESD Electrostatic Discharges
EN 61000-4-3:2006+A1:2008+
IS1:2009+A2:2010 Radiated RF Immunity
EN 61000-4-8:2010 Magnetic Field
EN 62479:2010 Human exposure
EN 300 440, v2.1.1 Electromagnetic compatibility + Radio spectrum Matters
Draft EN 301489-1, v2.2.0 Electromagnetic compatibility + Radio spectrum Matters
Draft EN301489-17, v3.2.0 Electromagnetic compatibility + Radio spectrum Matters
AS/NZS 4268 Radio Equipment and Systems –Short Range devices
AS/NZS 2772.2 Radio Frequency Fields (mean power < 1 mW)
Testing and conformity assessment performed by Jens-EMC and Liftup A/S
_____________________________________________________________________________________
The above products are manufactured under the following management system:
EN ISO 9001: 2008 Quality management, Certificate No. 44 100 117583
Director Søren Elisiussen
Title Name
Liftup A/S, Hagensvej 21, DK-9530 Støvring
Company
2018-08-15 _____________________________

Liftup Inc. | 4809 Ehrlich Road | Suite 105 | FL –33624, Tampa | T: [phone] | M: [e-mail] | www.liftup.us
———————————— USER MANUAL –REMOTE2 –US VERSION 1.0
9
3. Technical specifications
3.1 Remote control
2,4GHZ remote control: Short Range devices. Receiver Class 3
Dimensions (L x W x H): 80 x 64 x 33mm / 3,15 x 2,52 x 1,30 in.
Weight: 75 g (0,17 lbs.)
Frequency’s: 2,410GHz 2,435GHz and 2,460GHz
Duty cycle < 1%
Power: < 0,6mW Controlled environment, Hold to run.
Battery: 3 Volt CR2032
Water and dust: IP 42
Working temperature: +5ºC to +40ºC / 41ºF to 104ºF
Storage temperature: -25ºC to +70ºC / 13ºF to 158ºF
Expected service life: > 5 years
Right reserved to make technical modifications

10
Liftup Inc. | 4809 Ehrlich Road | Suite 105 | FL –33624, Tampa | T: [phone] | M: [email protected] | www.liftup.us
———————————— USER MANUAL –REMOTE2 –US VERSION 1.0
4. Configuration
Configuration of the “REMOTE2”must be carried out prior to mounting on the wall or on a
pole.
Set for “UP”
Connect
JP1 and JP2
And use
The “Lift”
push button
Set for “STAIRS”
Connect
JP1 and JP4
And use
The “Stairs”
push button
Set for “DOWN”
Connect
JP1 and JP3
And use
The “Lift”
push button

Liftup Inc. | 4809 Ehrlich Road | Suite 105 | FL –33624, Tampa | T: [phone] | M: [e-mail] | www.liftup.us
———————————— USER MANUAL –REMOTE2 –US VERSION 1.0
11
4.1 Battery
A CR2032 battery is installed in the remote control*.
ATTENTION: In order to ensure reliable function, swap the batteries every
2nd year.
To swap the battery, do the following:
1. Remove the black Push button front, loosen the 2 screws (PH1)
2. On the rear of the grey part, the PCB with the battery is mounted
3. Swap the battery
4. Refit the parts and test
DO NOT swallow coin cell battery. Keep batteries out of reach of small children.
Should a child swallow a battery, consult a physician immediately.
DO NOT dispose of batteries or electrical or electronic equipment with
unsorted household rubbish. When disposing of this device, ensure compliance
with local ordinances and regulations.

12
Liftup Inc. | 4809 Ehrlich Road | Suite 105 | FL –33624, Tampa | T: [phone] | M: [email protected] | www.liftup.us
———————————— USER MANUAL –REMOTE2 –US VERSION 1.0
4.2 Pairing of remote control
Pairing of the remote control is normally done by the dealer or the factory.
1.
The receiver, i.e. FlexStep must be switched off. The lift is switched on/off by activating
both the ON/OFF switch and the emergency stop
2.
Remove the front pushbutton and use a
small screwdriver to shorten the SJ2 on the
remote control* until the control LED on
the remote control* begins to flash slowly.
(If not mounted, press the S4 button which
has the same function)
3.
The remote control* is now in installation mode for 2 minutes.
4.
Within these 2 minutes, switch on the lift i.e. the FlexStep.
5.
The control LED on the remote control* is associated with the lift when it stops flashing.
Test the system, to ensure the pairing has been performed correctly; if not, repeat steps 1.-5.
above.
*Supplementary equipment
LED
SJ2

Liftup Inc. | 4809 Ehrlich Road | Suite 105 | FL –33624, Tampa | T: [phone] | M: [e-mail] | www.liftup.us
———————————— USER MANUAL –REMOTE2 –US VERSION 1.0
13
5. Disposal
It is the duty of the owner to dispose of the product in accordance with the regulations
applicable at the time.
Do not dispose of batteries or electrical or electronic equipment with unsorted household
rubbish. When disposing of this device, ensure compliance with local ordinances and regulations.
Please note that the remote control contains batteries which must be disposed of separately.
Consider contacting your dealer for assistance with disposal.
6. Right of warranty
The right of warranty is subject to the General Conditions for Supply which are presented here:
https://www.liftup.dk/media/3179/general-conditions-for-supply_liftup-inc.pdf.
ATTENTION: If the prescribed service inspections are not maintained the right
of warranty may be lost.
Failing to perform these inspections can also have serious consequences for product safety. It
rests with the customer to ensure compliance with the prescribed service inspections at all
times. Cf. Danish Working Environment Authority Executive Order 1109 §14.
7. Approvals and certificates
The REMOTE2 product is tested in compliance with the European radio and medical
specifications (CE - Declaration of Conformity) and certified according to the following radio
recommendations US and Canada:
REMOTE2:
FCC-ID: 2AK8H REMOTE2
IC-ID: 22516-REMOTE2
FCC and IC Statements
The REMOTE2 product contains radio transmitters that comply with CFR 47 Part 15.249 of the
FCC rules and with RSS-GEN, RSS-102 and RSS-247 of Industry Canada requirements.

14
Liftup Inc. | 4809 Ehrlich Road | Suite 105 | FL –33624, Tampa | T: [phone] | M: [email protected] | www.liftup.us
———————————— USER MANUAL –REMOTE2 –US VERSION 1.0
Notice statements according to CFR 47 Part 15.19 / RSS-GEN:
The REMOTE2 product complies with Part 15 of the FCC rules and with Industry Canada license
exempt standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Déclarations selon le CFR 47 section 15.19 / RSS-GEN:
Le présent REMOTE2 appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) L'appareil ne doit pas produire de brouillage, et
(2) L'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
NOTICE statements according to CFR 47 Part 15.21:
Changes or modifications made to this equipment not expressly approved by Liftup A/S may
void the FCC authorization to operate this equipment.
Statements according to CFR 47 Part 2.1091/2.1093 and OET bulletin 65/RSS- 102:
The REMOTE2 and REMOTE1 products are SAR test excluded according to FCC KDB 447498,
RSS102 and EN 62479 at separation distances larger than 5 mm and less than 50 mm with
respect to the human body as the maximal radiated power is below the limits.
The REMOTE2 and REMOTE1 products are by declaration of RF Exposure Compliance for
Exemption from Routine Evaluation Limits according to RSS102
ATTESTATION:
It is attested that the radio communication apparatus meets the exemption from the routine
evaluation limits in RSS102 Section 2.5 of this standard; that the Technical Brief was prepared
and the information contained therein is correct; that applicable measurement methods and
evaluation methodologies have been followed; and that the device meets the SAR and/or RF
field strength limits of RSS-102.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
SAR test exclusion according to EN 62479
The REMOTE2 and REMOTE1 products are compliant according to EN 62479 as the output
power is less than 20 mW.
AUS/NZ:
•The REMOTE2 complies with the AS/NZS 4268 requirements for 2.4 GHz transceiver.
Enjoy your new REMOTE2
Best regards,
Liftup Inc.