liftup HDN-Lift User manual

Liftup A/S | Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [email protected] | www.liftup.dk
User Manual
HDN
USER MANUAL –HDN –GB VERSION 1.4

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
2
Table of contents
1. Foreword.........................................................................................................................................................4
2. EU declaration of conformity .....................................................................................................................5
3. Type Certificate.............................................................................................................................................6
4. Factory Acceptance Test (FAT).................................................................................................................7
5. Terms of use...................................................................................................................................................8
6. Technical specifications................................................................................................................................9
7. Safety instructions ...................................................................................................................................... 10
7.1 Installation and maintenance............................................................................................................... 10
7.2 Unintended HDN-Lift movements ................................................................................................... 10
7.3 HDN-Lift movements .......................................................................................................................... 10
7.4 Avoid personal injury ........................................................................................................................... 10
7.5 Overload of the HDN-Lift.................................................................................................................. 10
8. Personal Safety............................................................................................................................................ 11
8.1 Anti-crushing .......................................................................................................................................... 11
8.2 Avoid personal injury ........................................................................................................................... 11
8.3 Safety plates............................................................................................................................................ 12
8.4 Handling................................................................................................................................................... 12
9. Functioning................................................................................................................................................... 13
10. Assembly....................................................................................................................................................... 13
11. Start-up ......................................................................................................................................................... 13
12. Operation..................................................................................................................................................... 14
12.1 Daily use.................................................................................................................................................. 14
12.2 Operating the HDN-Lift from the TOP level ................................................................................ 14
12.3 Operating the HDN-Lift from the BOTTOM level...................................................................... 15
12.4 Operating the HDN-Lift when the user is on it............................................................................ 15
13. Operation..................................................................................................................................................... 16
14. Maintenance................................................................................................................................................. 17
14.1 Cleaning................................................................................................................................................... 17
14.2 Mechanical maintenance ...................................................................................................................... 17
14.3 Remote control (accessory)............................................................................................................... 17
15. Installation and handover.......................................................................................................................... 18
16. Maintenance checklist................................................................................................................................ 19
17. Service log book ......................................................................................................................................... 20
18. Spare parts ................................................................................................................................................... 21
19. Electrical chart ............................................................................................................................................ 23
20. Disassembly ................................................................................................................................................. 24
21. Disposal ........................................................................................................................................................ 24

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
3
22. Warranty...................................................................................................................................................... 24

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
4
1.Foreword
Congratulations on purchasing your new wheelchair lifting platform.
This is an original user manual for your new HDN-Lift.
It is important to read this manual before using the lifting platform.
Set-up and installation MUST be undertaken by a qualified Liftup service technician, so as to
ensure correct assembly.
Improper assembly can lead to unintended danger elements.
The HDN-Lift is a new and innovative lifting platform for wheelchair users.
The solution sees elegant design combined with a robust construction, which can be adapted
to the environment. The platform is space-saving, and so does not need room for long ramps
or the like. The floor is raised and lowered gently and elegantly, which gives wheelchair users
and walking-impaired access to two levels.
The lifting platform is operated easily via operating panels mounted on the wall, or by means of
a stylish remote control.

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
5
2.EU declaration of conformity
Machinery directive 2006/42/EU
Manufacturer: Liftup A/S
Address:
Hagensvej 21, DK-9530 Støvring, Denmark
Telephone no.:
[phone]
hereby declares that:
Device: HDN-Lift
Hidden and lowerable lifting platform for wheelchair users and walking-
impaired
Year: 2012
conforms to the key health and safety requirements of the Machinery Directive:
The following was used in the assessment:
ISO 9386- 1: 2000 Power operated lifting platforms
Conforms with EU directive 2004/108/EU of 15th December 2004 on the
approximation of the laws of the Member States relating to Electromagnetic
Compatibility.
Director Flemming Eriksen
_________________ _______________________
Title Name
Liftup A/S, Hagensvej 21, DK-9530 Støvring
________________________________________
Place
01-13-2012
___________________ _____________________________
Date Signature

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
6
3.Type Certificate
COPY OF CE MARK INSERTED
HERE

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
7
4.Factory Acceptance Test (FAT)

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
8
5.Terms of use
This lifting platform is solely for the use of wheelchair users or the walking-impaired.
The max. load is 400 kg evenly distributed on the platform and a max. of 2 persons.
The model type and max. load can also be seen on the CE mark fitted internally on the safety
plates.
Read this user manual thoroughly before using the lifting platform.
The lifting platform may NOT be used for goods transport; no loaded pallets or other forms
of heavy loads on the platform.
The owner of the lifting platform is obliged to maintain the platform according to the
Maintenance Guide in section 12.

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
9
6.Technical specifications
Sample:
Technical specifications:
Power: 230V/50 Hz/min. 10A
Platform size: 1400 x 900/1000/1100 mm.
Dead weight: 110 kg. approx.
Pit depth: 350 mm.
Lifting height: 0 –500 mm.
Lifting capacity: 400 kg
Lifting speed: 20 mm/sec.
Noise level: < 70 dB.
Approval: Machinery Directive DS/EN 2006-42
Duty Cycle: 2 min. / 18 min

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
10
7.Safety instructions
7.1 Installation and maintenance
Do not attempt to install or maintain your HDN-Lift yourself.
This MUST be undertaken by an authorised* service technician.
Do NOT remove the protection or safety plates, as this may lead to personal injury.
7.2 Unintended HDN-Lift movements
If during the use of your HDN-Lift movement or action occurs which is not described in this
manual, stop the lifting platform and summon technical assistance.
If your HDN-Lift fails to move plane as a platform, a mechanical defect may have occurred –
summon technical assistance.
If the lifting platform does not stop respectively on the upper and lower levels level with the
floor, it may need calibration. Do this by moving the platform down to floor level and holding
down the down button for approx. 5 seconds.
If the problem continues, call technical assistance.
7.3 HDN-Lift movements
The space under the lifting platform must be kept free of all objects that may impair the
platform’s downward movement. Otherwise the platform cannot be moved to the lowest level
and thus not be used as a wheelchair lifting platform. Under normal circumstances no objects
will be able to get under the platform, as access is completely barred.
7.4 Avoid personal injury
So as to avoid personal injury it is NOT permitted to use the HDN-Lift when someone or
something is at risk of being injured by crushing, cutting, falling, slipping or similar.
The operator shall as far as possible ensure that movement can occur without putting
someone or something at risk.
Be extra careful when there are small children and disabled on or near the lifting platform, as
these groups cannot always be expected to be able to foresee the possible consequences of
the movement.
7.5 Overload of the HDN-Lift
In order to avoid material damage from overload (max. 400 kg evenly distributed) your HDN-
Lift is fitted with overload protection, which stops the platform in case of overload.
In such cases, move the platform down in order to exit it.
*Have gone through a product and service course at Liftup.

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
11
Safety Plates
8. Personal Safety
The HDN-Lift is fitted with various safety devices which ensure that the user and other
persons are not injured using the lifting platform.
8.1 Anti-crushing
The HDN-Lift is fitted with safety plates
on all open sides, which protect people
from crushing.
Do not remove these plates, as personal
injury may result.
Note too, that the plates function as
barriers, i.e. when the lifting platform
rises the plates will first move 100mm
upward before the platform begins to
move.
8.2 Avoid personal injury
-So as to avoid personal injury it is NOT permitted to use the HDN-Lift when
someone or something is at risk of being injured by crushing, cutting, falling, slipping or
similar.
-It is important that the operator ensures that the platform can move without putting
anyone or anything at risk.
-Be extra careful when there are small children and disabled on or near the lifting
platform, as these groups cannot always be expected to be able to foresee the
possible consequences of the movement.
-Never try to load more on the lifting platform than stated on the load sign’s max. load
(400 kg.).

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
12
8.3 Safety plates
When the HDN-Lift is moved to the “lift up” position, the safety plates will first rise and lock
before the lifting platform begins to move. These plates are now acting as barriers.
When the lifting platform is moved into the down position, the safety plates will automatically
lower into the lifting platform, and it can then be exited.
Plane floor, ready for roll-on and roll-off Safety plates in up position Lift up, ready for roll-off
8.4 Handling
The HDN-Lift is normally supplied by your dealer, who also takes care of installation.
Do not try to move the lifting platform manually, as this can lead to permanent injury. The
product should be moved and handled with suitable lifting equipment (pallet-truck, roller plate
or the like).
Do not subject the lifting platform to severe knocks as this can affect functionality.
Keep the supplied remote control* dry and do not subject it to severe blows, such as by
throwing it. Cleaning may only be done using a well-wrung cloth.
Never use a high-pressure jet or hose to rinse the lifting platform, as this can damage the
product.
* Additional equipment

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
13
9.Functioning
The HDN-Lift is a so-called “dead man operated” lifting platform, i.e. the buttons must be
depressed during the entire motion.
The platform works simply by the user calling it by pressing one of the buttons on the wall, or
by using the supplied remote control*.
When the user is on the lifting platform this is operated from the panel by the platform, where
one can choose to be conveyed to a higher or lower level.
10. Assembly
The lifting platform must be installed by an authorised service technician.
Do not attempt to transport or uninstall your HDN-Lift, or to repair it.
This MUST be undertaken by an authorised service technician.
Improper assembly can pose risks for user personal safety. Liftup disclaims any liability if
assembly and installation are not performed by an authorised service technician.
For more information or materials on assembly, contact your dealer.
11. Start-up
The HDN-Lift’s control unit should always be connected to a 230V socket and be switched
on.
Normally the lift is in constant stand-by mode, i.e. it is ready for use as soon as one of the
operating buttons is pressed.
* Additional equipment

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
14
HDN-Lift ready for drive on from the top level
12. Operation
12.1 Daily use
The HDN-Lift is operated using the two operating panels respectively above and below the
platform, a button panel sited by the platform or by using the remote control*. The remote
control replaces or supplements the operating panels.
* Additional equipment
12.2 Operating the HDN-Lift from the TOP level
In order to call the HDN-Lift to the TOP level, depress the button sited above the
platform.
The lifting platform starts by raising the safety plates, and then it moves up to the top level.
Remember to depress the push button for the entire time, since the platform will
automatically stop when the button is released.
The platform stops automatically when it reaches the top level. Now the user can enter the
lifting platform.
Call the lifting platform
up or down
Fig. 1
Fjernbetjening

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
15
HDN-Lift ready for drive on from the bottom level
12.3 Operating the HDN-Lift from the BOTTOM level
If the lifting platform is not already at the bottom level, call it as follows:
In order to call the HDN-Lift to the BOTTOM level, depress the button sited
below the platform.
The platform begins to move towards the bottom level. When this level has been reached, the
safety plates continue to drive down. When the safety plates are completely down and plane
with the floor, the platform automatically stops, and is now ready to enter.
Remember to depress the push button for the entire time, since the platform will
automatically stop when the button is released.
12.4 Operating the HDN-Lift when the user is on it
Use of the lifting platform is performed by using the button sited by the platform, or
by using the remote control*.
-To raise the lifting platform, press the top button and hold it down until the platform
stops.
-To lower the platform, press the bottom button and hold it down until the platform
stops, and the safety plates are completely down.
* Additional equipment

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
16
13. Operation
Under normal operating conditions the lifting platform shall always be connected to 230V.
The platform is in standby-mode when it is not being used, and will always be ready for use as
desired.
IMPORTANT!
If you notice the lifting platform not working as expected or if it stops after a few centimetres,
technical problems may have arisen which require remedial work by technically qualified
personnel. Contact your dealer for further help.

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
17
14. Maintenance
14.1 Cleaning
General cleaning may only be done using a well-wrung cloth.
Do NOT use a high-pressure jet or rinse the HDN-Lift directly using a hose.
14.2 Mechanical maintenance
The mechanical maintenance of the lifting platform shall normally only be undertaken in
connection with the regular service inspection. This is to be undertaken by an authorised
service technician 2/4 times a year, depending on whether the platform is indoors or
outdoors.
Should unexpected errors or jarring sounds occur, contact your dealer at once.
14.3 Remote control (accessory)
Two batteries are installed in the remote control. In order to ensure reliable function
swap the batteries every 6 months. To swap the batteries, do the following:
1. Loosen the screw on the rear of the remote control
2. Remove the back panel
3. Loosen the screw which holds the batteries
4. Swap the batteries
5. Refit the battery holder
6. Refit the back panel and test
The remote control uses 2 x AAA batteries.

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
18
15. Installation and handover
Sample:

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
19
16. Maintenance checklist
In addition to the general maintenance described in section 12, we recommend as the
manufacturer, that routine inspections are undertaken every 6 months by an authorised
service technician. The dealer you have bought the product from will offer this service, but if
you wish to use another service provider, the owner of the HDN-Lift is responsible for
ensuring that the chosen service technician is qualified in the product in question.
For safety reasons it is very important that these inspections are maintained, since lacking or
improperly performed inspections may result in personal injury.
IMPORTANT!
Before inspecting the lifting platform (or under it), the platform MUST be dismounted from the
controls in order to secure against accidental operation. The service technician is responsible
for performing this disassembly before starting servicing.
It is not enough to disconnect the 230V supply, as the system is fitted with a battery
backup.
Sample:

USER MANUAL –HDN –GB VERSION 1.4
Liftup A/S Hagensvej 21| DK-9530 Støvring | Denmark | T: [phone] | M: [e-mail] | www.liftup.dk | CVR DK-1015 3964
20
17. Service log book
This form shall be filled in after every inspection.
Sample: