Light Efficient Design LUMICLEANSE LC-UVC-TOWER-216W-01 User manual

QUICK START GUIDE
LC-UVC-TOWER-216W-01
WARNING! POSSIBLE RISK OF INJURY TO EYES AND SKIN.
•Hazardous optical radiation may be emitted from the light source. Do not look
at an operating lamp. It may be harmful to the eyes.
•UVC is emitted from the light source. Eye or skin irritation may result from
exposure. Use appropriate shielding.
•IR may be emitted from the light source. Do not look at operating lamp.
CAUTION!
•To avoid eyes and skin exposure to UV light, it is forbidden for animals,
plants and all personnel to be present when the UV lamp is on.
•Always disconnect mains supply before removing any fixture covers.
•Keep this device away from rain and moisture.
INSTALLATION AND USERS GUIDE

INSTALLATION AND USERS GUIDE
Read before using
Thank you for purchasing a LUMICLEANSE product. This manual is a quick operation
guide to get you started. For more information, please always refer to the full version
user manual provided.
Before unpacking, please check and be sure that the package is in good condition
with no damage on the carton during transportation. In the package, you will find the
following:
LC-UVC-TOWER-216W-01
(with UV Tube)
Remote Control UV Glasses Warning Sign
Product information
Voltage Power Net Weight Size
AC100-240V, 50/60Hz 230W 31.5 lb /
14.3 kg
20.0” x 17.4” x 58.6”
507x442x1487.83mm
①Grid Opening Tabs ⑥Power Switch (I/O) ⑪30 mins –touch key
②Handle ⑦Power Cable ⑫60 mins -touch key
③Infrared Inductor ⑧Universal Wheel ⑬120 mins -touch key
④Protective Grid ⑨Brake ⑭Start –touch key
⑤UV Tube ⑩Indicator Light ⑮Power Indicator

INSTALLATION AND USERS GUIDE
Preparation and Notes
•Before using the product, remove the foam (protecting the UV tube) inside the product: pull
up the 2 locking Tabs to open the Grid and take the foam out carefully, then re-install the
Grid.
•The 3universal wheels of this device had been turned
inwards and fixed by 3screws at the center of the bottom
when it was packed.Before moving and using the product,
the 3wheels must be installed back to the correct positions:
pressing the 3screws and swing the wheels outwards 180°,
then fix the wheels in place using those 3screws.
•Keep in mind of the following information:
Delayed Start Time
Recommended Disinfection Times/Areas
3 minutes 30mins/60m² 60mins/120m²
120mins/180m²
•Place the supplied Warning Sign in a conspicuous place at the entrance/exit of disinfection
area.
•Make sure the path to exit the disinfection area is clear before starting the device.
•The operator must wear anti-ultraviolet protective clothing and the UV Glasses before
operating.
•The operator must leave the disinfection area and close all entrances after starting the
device, make sure the entrances are locked or safeguarded during the entire disinfection
process.
•For safety reasons, when the UV lamp is operating, it will turn off when the sensor detects
movement and it will immediately continuous audible dual beep and flashing red and green
LED indicator lights will engage.The lamp won’t restart again. The operator will have to
manually or remotely re-start the light again to ensure the area is disinfected.
•To avoid moving by itself, this device must be placed on an even surface and always apply
the wheel brake before operating.

INSTALLATION AND USERS GUIDE
Operation
•Switch on the device, the green power indicator light turns on.
•On either the fixture control panel or supplied remote control：
1> Press the <30 mins>, <60 mins> or < 120 mins> touch key/button to select your
desired disinfection time, the touch key indicator light turns on.
2> Press the start touch key/ button, audible alarm starts beeping and red power indicator
will flash regularly for 3 minutes. You must exit within this 3 minutes.
•The UV tubes will light up once the beeping countdown ends, the power indicator turns
red and stays on during the entire disinfection process.
•Once the disinfection process ends, the touch indicator turns off and the power indicator
switches to green. Also an audible alarm sounds.
•Open the doors and windows to ventilate the disinfected area.
Control Panel Remote control
*** If the remote control loses pairing with the device, re-do the pairing by pressing the Start
button on the remote control and switch on the device for 5 seconds. One remote control can
be matched with multiple units of the same model. ***