Light Emotion COB100UV Operator's manual

www.lightemotion.com.au
COB100UV
100W COB UV LED Flood Light.
User’s instruction manual
This manual contains important information about the safe installation and use of this product
Please read this instruction manual carefully before installing or operating
Please keep these instructions in a safe place for future reference
V1.01

1
Contents
1. Safety Instructions 2
2. Installation 3
3. Features 3
4. Operation 3
Menu Functions 4
Explanations 5
5. DMX Profile Chart 5
6. DMX Connections 6
7. DMX Address Setting 6
8. DMX Terminator 6
9. Cleaning and Maintenance 7
10. Technical Data 7
11. Warranty 7

2
Introduction
Thank you for the purchase of your COB100UV COB LED 100W UV Ultra Violet Wash Fixture by Light Emotion.
We are confident you will be satisfied with your purchase and enjoy many years of use from this Professional Light
Emotion product. Please read these instructions carefully to ensure the product is well look after and used correctly
to avoid any potential problems.
Please note that as part of our ongoing commitment to continuous improvement and product development, the
specifications in this manual are subject to change without notice. Whilst every care has been taken in the
preparation of this manual we reserve the right to change specifications in the course of product improvement.
What is in the box:
- 1 x COB100UV fixture
- Power cable
- 40 and 80 degree lens
- This user manual
1. Safety Instructions:
Please read these instructions carefully. It includes important information about the installation usage and
maintenance of this product.
- Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also
receive this instruction booklet.
- Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is
not higher than that stated on the sticker of the fixture.
- This product is intended for indoor use only. To prevent risk of fire or shock, do not expose fixture to rain or
moisture.
- Make sure there are no flammable materials close to the unit while operating.
- The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surface. Be sure that
no ventilation slots are blocked.
- Always disconnect from power source before servicing.
- Secure fixture to stands, trussing and the like using a safety chain.
- Maximum ambient temperature is 40˚C. Do not operate fixture at temperatures higher than this.
- In the event of serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized
technical assistance centre.
- Make sure power cord is never crimped or damaged.
- Never disconnect power cord by pulling or tugging on the cord.
- Never carry the fixture directly from the cord. Carry by holding the unit directly or via the hanging bracket.
- Avoid direct eye exposure to the light source while it is on.

3
2. Installation:
Caution: For safe mounting of this product, please read the following carefully.
- Use a suitable clamp to attach to lighting stand, trussing or bar, together with safety chain.
- When mounting the product, do not stand directly underneath the product
- Always use a safety chain when mounting the product on stands, trussing or bars. Make sure the breaking strain
rating of the chain is at least 10 times the weight of the product.
- Make sure there is adequate ventilation around the product.
- Never look directly into the LED light or laser sources of the product.
- For indoor use only – do not use outdoors.
- To avoid electrical shock, keep away from rain and moisture.
3. Features
This product is designed as entertainment effect lighting fixture and is only intended to be used as an effect for
entertainment and production applications. Due to our ongoing commitment to constantly reviewing and improving
products, features and specifications are subject to change without prior notice.
It features 1 100W UVCOB LED which is a single LED source designed to be very bright. Being a single UV LED
source, the light outputs UV as a UV flood light. This product produces true UV, not just purple or dark blue light.
This unit has built-in protection which will shut off the unit should its internal temperature reach 85 degrees C. This
protects the internal electronics and components from damage caused by over heating.
- Power input: AC 100V-240V/50HZ-60HZ
- Wattage: 97W
- LEDs: 1 pc 100W COB UV LED
- Beam angle of LEDs: 80 degree, or 40 degree with interchangeable lens included
- 3-pin female XLR socket and 3-pin male XLR socket
- Built-in microphone
- Four button LED digit display
- Fuse: M205 2A slow blow
- Maximum 7 fixtures can be daisy chained together for power (DMX technically unlimited)
- Weight: 3.5 kg
- Size: 330x245x192mm
4. Operation.
The COB100UV has 6 modes of operation which are as follows:
Manual dimmer colour mode, Sound active mode, Auto-run program mode, Other program
select mode, Slave mode, DMX mode
Each mode is accessed by pressing the MODE button. The DP dot of fourth digital tube will be

4
flicker when you operate it, then the DP dot will be automatically off after 20 seconds if there is no
further input. The four digital tube will display current operation mode. You have to press the
MODE button if you want to operate the unit again.
MODE manual
SET UP manual UP/DOWN manual Instruction
DMX MODE Address ~ Sets the DMX starting address
SLAVE MODE Slave mode Set the unit into slave mode
DIMMER
MODE
UV dimmer ~ Adjust the intensity of the UV colour
Flash ~ Adjust the flash speed, is flash
off , is slowest, is fastest
SOUND
MODE
Mode select
Sensitivity select
~ Adjust the sensitivity of the sound-active,
is the lowest level, is the
highest level.
COLOUR
DREAMING
MODE
Speed set ~ Adjust the speed of the colour dreaming mode – as
this is single colour light, this represents fading in
and out.
OTHER
MODE
Display
on/off
LED digital tube display always on
LED digital tube display off
Display
normal/inverse
LED digital tube display normal
LED digital tube display inversion
Initialization mode Initialize the unit at the extra factory setting
A. Manual dimmer colour mode
1) Manual dimmer colour select
Press "MODE" button, select the manual dimmer colour select mode. At this time, the four digital
tube displays UV " ~ ", then press "UP" or "DOWN" button to set the dimming
rate 0-255.
2) Flash speed select
Press "SET UP" to choose the flash speed select mode. At this time, the four digital tube displays
" ~ ". Press "UP" or "DOWN" button to select the flash speed 00-15, 00 is flash off,
01 is the slowest flash speed, 15 is the fastest flash speed.
B. Sound active mode
Press "MODE" button, select the sound active program mode. At this time, the four digital tube
displays " ~ ", then press "UP" or "DOWN" to select the sound active the
sensitivity 1-8. 1 is off sound-active, 2 is the lowest sensitivity,8 is the highest sensitivity.
C. Colour dreaming mode
Press "MODE" button ,select the colour dreaming mode. At this time, the four digital tube displays
" ~ ", then press "UP" or "DOWN" button to select the colour dreaming speed
01-16, 01 is the slowest speed, 16 is the fastest speed.

5
D. Other program select mode
1) Display off/on select mode
Press “SET UP” button, select display off/on mode. Press UP or DOWN to select the four digital
tube display on/off. When the digital tube displays " " means that the display will on in any
situation, when the digital tube displays " " means that the display will be automatically off
after 60 seconds if there is no operation.
2) Display normal/inversion select mode
Press “SET UP” button, select display normal/inversion mode. Press UP or DOWN to select the
four digital tube display normal/inversion. When the digital tube displays " " means that
the digital tube displays normally, when the digital tube displays " " means that the digital
tube displays inversion.
3) Initialization select mode
Press “SET UP” button until the four digital tube displays " ", and the display is flicker.
Now press UP button and DOWN button at the same time, you can initialize it at extra factory
setting, running on the colour dreaming mode, and the four digital tube displays" ".
E. Slave mode
Press "MODE" button, select salve mode. At this time, the four digital tube displays " ".
Press SET UP, UP or DOWN is no use under this mode.
F. DMX mode
The control Board allows you to assign the DMX address which is defined as the first channel of
the LED PAR. Press “ MODE ” button until the display is “ ~ ” , then press UP or
DOWN to set the DMX address. The four digital tube display will be flicker when there is no
controller signal. This fixture is 1 DMX channel only.
5. DMX Profile Chart.
Channel Value Function
1
0 - 255
MASTER DIMMER
0% - 100%

6
6. DMX-512 Control Connection
Using a 3 pin XLR cable, you can connect the product to a DMX controller and then to other fixtures
with 3 pin XLR inputs and outputs. When not using DMX, multiple fixtures can be connected together
and operate under master/slave control. The signal cable should have two core with shielded cable, the
signal connectors are XLR input and output connectors. Please refer to the below diagram:
7. DMX Address Setting
When being used in conjunction with a DMX controller, each fixture must be set a specific starting
address. When receiving signal, fixture will receive channel control signals of this address from the
DMX controller.
For simplicity, the user can use the same address for multiple fixtures but this will result in each fixture
providing exactly the same output and fixtures with the same DMX address cannot be individually
controlled.
To control each fixture individually via DMX, each fixture must have its own unique DMX address.
This fixture uses only 1 DMX channel so it is a simple matter of having each DMX channel 1 channel
apart (1,2,3 and so on).
Some DMX controllers may group fixtures in lots of 16 channels – so in that case, fixture 1 on channel 1,
fixture 2 on channel 17, 3 on 33, and so on. Refer to your DMX controllers’ instruction manual on how
best to manage your DMX channel allocation.
8. DMX-512 connection with DMX terminator
A DMX terminator helps to reduce ‘noise’ on the DMX chain, and makes the light respond to control
more accurately. It should be plugged in to the last fixture in any chain. For Terminator connections
please see below:

7
9. Cleaning and Maintenance
From time to time it is recommended the product is cleaned to ensure maximum light output and
performance. Use a wet cloth to clean the housing as well as the lenses. Please note that alcohol based
cleaners and solvents cannot be used as they will cause damage to the product.
When used in a fixed long term installation such as a venue or club, the unit should be periodically taken
down from the installation and professionally cleaned. Dust build-up within the unit can cause damage
and ultimately failure of components.
10. Technical Data
- Power input: AC 100V-240V/50HZ-60HZ
- Wattage: 132W
- LEDs: 1 pc 150W COB LED (RGBW 4 in 1)
- Beam angle of LEDs: 80 degree, or 40 degree with interchangeable lens included
- 3-pin female XLR socket and 3-pin male XLR socket
- Built-in microphone
- Four button LED digit display
- Fuse: M205 2A slow blow
- Maximum 5 fixtures can be daisy chained together for power (DMX technically unlimited)
- Weight: 4.1 kg
- Size: 415x245x192mm
11. Warranty
This product is warranted for 2 years from your purchase date. We are confident that this product will
give many years of trouble-free operation but should an unlikely problem arise, warranty claims must be
via the original place of purchase, together with the original purchase receipt. Please keep both your
original purchase receipt and this instruction manual together and in a safe place for future reference.
Should the product be sold within the warranty period, be sure to pass on both to the new purchaser so
they are able to claim warranty should they need to. We recommend you register your warranty online at
www.industrygear.com.au.
Purchased from:_________________________________________
Contact Details:_________________________________________
Date Purchased:_________________________________________
Invoice/Receipt Number:__________________________________
Copyright Light Emotion 2017. E&OE
Exclusively imported by LSW Imports and Distribution
PO Box 887, Kingsgrove, NSW, 2208 - 1800 643 111 (within Australia) / [phone] (outside of Australia)
[email protected] - www.lightemotion.com.au