Lightcloud LCCONTROL/MINI User manual

LCCONTROL/MINI
Controller Mini
1 (844) LIGHTCLOUD
1 (844) 544-4825
WE’ RE HER E TO HELP:
1 (844) LIGHTCLOUD
© 2022 RAB Lighting, Inc
1 (844) 544-4825
Lightcloud is a commercial
wireless lighting control system.
It’s powerful and flexible,
yet easy to use and install.
Learn more at lightcloud.com

FCC Information:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
Note: This device has been tested and found to comply with the limits for
Class A digital devices pursuant to Part 15A Subpart B, of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential environment. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instruction manual, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to
try and correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
To comply with the FCC's RF exposure limits for general population /
uncontrolled exposure, this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or
transmitter.
CAUTION: Changes or modifications to this equipment not expressly
approved by RAB Lighting may void the user’s authority to operate
this equipment.
Hello
The Lightcloud Controller Mini
is a remotely controlled switch
and 0-10V dimming device.
Product Features
Wireless Control & Configuration
Switching up to 4.2A
0-10V Dimming
Power Monitoring
Patent Pending

Contents
Lightcloud Controller
Instruction Manual
Wire Nuts
Lock Nut O-ring
x 3 x 3
Controller requires constant, unswitched power. Any wires not in use
must be capped off or otherwise insulated. This product should
only be installed by a qualified electrician and in compliance
with local and national electrical codes.
!
Specifications
PART NUMBER
LCCONTROL/MINI
INPUT
120V-277VAC, 60Hz
<0.8W (Standby and Active)
MAXIMUM SWITCHED LOAD RATINGS
For Control of Electronic Ballast (LED)
and Magnetic Ballast
Electronic/Tungsten: 4.2A @120VAC
Inductive/Resistive: 4.2A @120VAC, 1.8A @277VAC
OPERATING TEMPERATURE
-35ºC to +60ºC
OVERALL DIMENSIONS
1.6" diameter, 3.8" length
1/2" NPT Mount, Male
22AWG pigtails
18AWG pigtails
WIRELESS RANGE
Class 2
IP66 Rated
Indoor and Outdoor Rated
Wet and Damp Location
Plenum Rated
Line-of-Sight: 1000 feet
Obstructions: 100 feet
Operating Modes
CONTROLLER: Provides switching and dimming for a single zone.
REPEATER: Extends the Lightcloud mesh network without controlling
a load.
SENSOR (REQUIRES OPTIONAL SENSOR MODULE): Provides occupancy,
vacancy, and daylight harvesting.
POWER MEASUREMENT: The Lightcloud Controller is capable of
measuring the power usage of the attached circuit.
POWER LOSS DETECTION: If mains power to the Controller is lost, the
device will detect this and alert the Lightcloud application.
EMERGENCY DEFAULT: If communication is lost, the Controller may
optionally fall back to a specific state, such as turning the attached
circuit on.
1 (844) LIGHTCLOUD
or 1 (844) 544-4825
WE’RE HERE TO HELP:
Functionality
Configuration
To configure Lightcloud products, use the Web Application
(control.lightcloud.com) or call 1(844)LIGHTCLOUD.

What You Need
Lightcloud Gateway
A Lightcloud installation requires at least
one Lightcloud Gateway to manage your devices.
1 (844) LIGHTCLOUD
or 1 (844) 544-4825
WE’RE HERE TO HELP:
5Confirm Device Connectivity
Confirm Status Indicator is Solid Green (see details below)
Log on to www.lightcloud.com or call 1 (844) LIGHTCLOUD
6Commission your devices
Controller Mini
Lightcloud
®
Solid GREEN when connected to your
Lightcloud network. Blinking RED when not
connected. The device will automatically
continue trying to connect to a network
in Setup Mode.
Illuminates when the device receives a
message and blinks the signal strength.
3 Blinks - Best signal
2 Blinks - Acceptable signal
1 Blinks - Unacceptable signal
Consult the “Finding a Location” section
for more information
STATUS INDICATOR
SIGNAL INDICATOR
• Illuminated when device is powered
• Press once to highlight this device in the
Lightcloud Application
•
• Press twice and hold to set dim level
Press twice to toggle circuit on and off
• Press and hold for 10 seconds to remove
this device from a Lightcloud network
• Blinks when device is indicated from the
Lightcloud Application
DEVICE IDENTIFICATION BUTTON
Setup & Installation (cont’d)

Wiring
To add new devices to your Lightcloud network, call RAB at
4Power up
PINKPINK
MODULARMODULAR
REDRED
PURPLEPURPLE
WHITEWHITE WHITEWHITE
BLACKBLACK BLACKBLACK
120-277 VAC
Load or
Fixture
Controller Mini
Lightcloud
®
Device Table
3b
For setup and maintenance, we provide two Lightcloud Device
Tables with the Gateway: one that you can attach to your panel
and one to hand off to a building manager. Attach the Device
Identification stickers included witheach device to a row,
then write in additional information, such as Zone name,
Panel/Circuit Number, and whether or not a zone uses
dimming.
Send to RAB: Once all of the devices have been added and
organized, submit the information for commissioning.
D E V IC E I D s
DEVICE 1D ZONE NAME
PANEL/
CIRCUIT # DIMMING

Setup & Installation (cont’d) Setup & Installation
1
OFF
WARNING
OFF
Turn Off Power
Find a Suitable Location
1a
Lightcloud Installer Application
3a
3Labeling Your device
Use these guidelines when installing devices:
• If there is a clear line of sight between two Lightcloud
devices, they can be placed up to 1000 feet apart.
• If the two devices are separated by ordinary drywall
construction, try to keep them within 100 ft. of each other.
• Brick, concrete and steel construction may require
additional Lightcloud devices to go around the obstruction.
LightcloudGateway
<= 100 ft.
Add an additional Lightcloud
Device to extend network range
around corners B R I C K ,
CONC R E T E O R
M E T A L WA L L
D R Y W A L L
O R S I MIL A R
When installing devices, it’s important to keep track of their Device
IDs, installation locations, panel/circuit #s, dimming function, and any
additional notes. To organize this information, use the Lightcloud
Installer Application (A) or Device Table (B).
Install the LC Installer Application: LC Installer is available
for iOS and Android.
Scan & Install Lightcloud Devices: Scan each device and
assign to a room. It’s recommended that each device is
scanned just before or just after being wired so no devices
are missed. The more notes that are given, the easier it is to
commission the system.
Device Scanner
Enter Manually
PLACE RECTANGLE TO FIT CODE ON LABEL
Scan Device Code
Device Info
SaveCancel
Device ID 0013A20040B62A4A
Location Office
Zone Name Office Lights
Dimmable
Power Monitoring
Enter Device Information
Repeat for Additional Devices
Devices
Add DeviceSend to RAB
Office Light - ID 0013A20040B62A4A
Controller
Office Light - ID 0013A20040B62A4B
Sensor
Office Light - ID 0013A20040B62A4C
Dimmer
Office Light - ID 0013A20040B62A4D
Daylight
Office Light - ID 0013A20040B62A4E
Touch
Send to RAB
Device Scanner
Enter Manually
PLACE RECTANGLE TO FIT CODE ON LABEL

Setup & Installation (cont’d)
2Install your Lightcloud Controller
NOTE: The National Electrical Code requires that low-voltage
wiring used in the same enclosure as high-voltage wiring have
an equal or better insulation rating. You may need to complete
your low-voltage wiring in another enclosure or use a partition.
0-10V DIMMING
0-10V is a common method of low-voltage control of dimmable
drivers and ballasts. Purple: 0-10V positive | Pink: 0-10V common
2a Install at a Junction Box (Indoor/Outdoor)
2b Install at Lighting Panel or Trough
Space and code allowing, you may install Lightcloud devices directly
in your breaker box or lighting panel. Alternatively, break out lighting
circuits and install Lightcloud devices in a separate trough.
Controller requires constant, unswitched power.
!
When power switch
is set to OFF
Controller is disconnected
from network
OFF
P O W E R L O A D
DON’T
Controller always has power and is
connected to the network
P O W E R L O A D
DO
WHITE
BL ACK
Controller Mini
Lightcloud
®
RED
WHITE
BLACK
BL ACK
PINK
PURPLE
To Load
To PanelTo Driver/Ballast
MODULAR CABLE

Setup & Installation (cont’d)
2Install your Lightcloud Controller
NOTE: The National Electrical Code requires that low-voltage
wiring used in the same enclosure as high-voltage wiring have
an equal or better insulation rating. You may need to complete
your low-voltage wiring in another enclosure or use a partition.
0-10V DIMMING
0-10V is a common method of low-voltage control of dimmable
drivers and ballasts. Purple: 0-10V positive | Pink: 0-10V common
2a Install at a Junction Box (Indoor/Outdoor)
2b Install at Lighting Panel or Trough
Space and code allowing, you may install Lightcloud devices directly
in your breaker box or lighting panel. Alternatively, break out lighting
circuits and install Lightcloud devices in a separate trough.
Controller requires constant, unswitched power.
!
When power switch
is set to OFF
Controller is disconnected
from network
OFF
P O W E R L O A D
DON’T
Controller always has power and is
connected to the network
P O W E R L O A D
DO
WHITE
BL ACK
Controller Mini
Lightcloud
®
RED
WHITE
BLACK
BL ACK
PINK
PURPLE
To Load
To PanelTo Driver/Ballast
MODULAR CABLE

Setup & Installation (cont’d) Setup & Installation
1
OFF
WARNING
OFF
Turn Off Power
Find a Suitable Location
1a
Lightcloud Installer Application
3a
3Labeling Your device
Use these guidelines when installing devices:
• If there is a clear line of sight between two Lightcloud
devices, they can be placed up to 1000 feet apart.
• If the two devices are separated by ordinary drywall
construction, try to keep them within 100 ft. of each other.
• Brick, concrete and steel construction may require
additional Lightcloud devices to go around the obstruction.
LightcloudGateway
<= 100 ft.
Add an additional Lightcloud
Device to extend network range
around corners B R I C K ,
CONC R E T E O R
M E T A L WA L L
D R Y W A L L
O R S I MIL A R
When installing devices, it’s important to keep track of their Device
IDs, installation locations, panel/circuit #s, dimming function, and any
additional notes. To organize this information, use the Lightcloud
Installer Application (A) or Device Table (B).
Install the LC Installer Application: LC Installer is available
for iOS and Android.
Scan & Install Lightcloud Devices: Scan each device and
assign to a room. It’s recommended that each device is
scanned just before or just after being wired so no devices
are missed. The more notes that are given, the easier it is to
commission the system.
Device Scanner
Enter Manually
PLACE RECTANGLE TO FIT CODE ON LABEL
Scan Device Code
Device Info
SaveCancel
Device ID 0013A20040B62A4A
Location Office
Zone Name Office Lights
Dimmable
Power Monitoring
Enter Device Information
Repeat for Additional Devices
Devices
Add DeviceSend to RAB
Office Light - ID 0013A20040B62A4A
Controller
Office Light - ID 0013A20040B62A4B
Sensor
Office Light - ID 0013A20040B62A4C
Dimmer
Office Light - ID 0013A20040B62A4D
Daylight
Office Light - ID 0013A20040B62A4E
Touch
Send to RAB
Device Scanner
Enter Manually
PLACE RECTANGLE TO FIT CODE ON LABEL

Wiring
To add new devices to your Lightcloud network, call RAB at
4Power up
PINKPINK
MODULARMODULAR
REDRED
PURPLEPURPLE
WHITEWHITE WHITEWHITE
BLACKBLACK BLACKBLACK
120-277 VAC
Load or
Fixture
Controller Mini
Lightcloud
®
Device Table
3b
For setup and maintenance, we provide two Lightcloud Device
Tables with the Gateway: one that you can attach to your panel
and one to hand off to a building manager. Attach the Device
Identification stickers included witheach device to a row,
then write in additional information, such as Zone name,
Panel/Circuit Number, and whether or not a zone uses
dimming.
Send to RAB: Once all of the devices have been added and
organized, submit the information for commissioning.
D E V IC E I D s
DEVICE 1D ZONE NAME
PANEL/
CIRCUIT # DIMMING
Setup & Installation (cont’d)

What You Need
Lightcloud Gateway
A Lightcloud installation requires at least
one Lightcloud Gateway to manage your devices.
1 (844) LIGHTCLOUD
or 1 (844) 544-4825
WE’RE HERE TO HELP:
5Confirm Device Connectivity
Confirm Status Indicator is Solid Green (see details below)
Log on to www.lightcloud.com or call 1 (844) LIGHTCLOUD
6Commission your devices
Controller Mini
Lightcloud
®
Solid GREEN when connected to your
Lightcloud network. Blinking RED when not
connected. The device will automatically
continue trying to connect to a network
in Setup Mode.
Illuminates when the device receives a
message and blinks the signal strength.
3 Blinks - Best signal
2 Blinks - Acceptable signal
1 Blinks - Unacceptable signal
Consult the “Finding a Location” section
for more information
STATUS INDICATOR
SIGNAL INDICATOR
• Illuminated when device is powered
• Press once to highlight this device in the
Lightcloud Application
•
• Press twice and hold to set dim level
Press twice to toggle circuit on and off
• Press and hold for 10 seconds to remove
this device from a Lightcloud network
• Blinks when device is indicated from the
Lightcloud Application
DEVICE IDENTIFICATION BUTTON
Setup & Installation (cont’d)

Contents
Lightcloud Controller
Instruction Manual
Wire Nuts
Lock Nut O-ring
x 3 x 3
Controller requires constant, unswitched power. Any wires not in use
must be capped off or otherwise insulated. This product should
only be installed by a qualified electrician and in compliance
with local and national electrical codes.
!
Specifications
PART NUMBER
LCCONTROL/MINI
INPUT
120V-277VAC, 60Hz
<0.8W (Standby and Active)
MAXIMUM SWITCHED LOAD RATINGS
For Control of Electronic Ballast (LED)
and Magnetic Ballast
Electronic/Tungsten: 4.2A @120VAC
Inductive/Resistive: 4.2A @120VAC, 1.8A @277VAC
OPERATING TEMPERATURE
-35ºC to +60ºC
OVERALL DIMENSIONS
1.6" diameter, 3.8" length
1/2" NPT Mount, Male
22AWG pigtails
18AWG pigtails
WIRELESS RANGE
Class 2
IP66 Rated
Indoor and Outdoor Rated
Wet and Damp Location
Plenum Rated
Line-of-Sight: 1000 feet
Obstructions: 100 feet
Operating Modes
CONTROLLER: Provides switching and dimming for a single zone.
REPEATER: Extends the Lightcloud mesh network without controlling
a load.
SENSOR (REQUIRES OPTIONAL SENSOR MODULE): Provides occupancy,
vacancy, and daylight harvesting.
POWER MEASUREMENT: The Lightcloud Controller is capable of
measuring the power usage of the attached circuit.
POWER LOSS DETECTION: If mains power to the Controller is lost, the
device will detect this and alert the Lightcloud application.
EMERGENCY DEFAULT: If communication is lost, the Controller may
optionally fall back to a specific state, such as turning the attached
circuit on.
1 (844) LIGHTCLOUD
or 1 (844) 544-4825
WE’RE HERE TO HELP:
Functionality
Configuration
To configure Lightcloud products, use the Web Application
(control.lightcloud.com) or call 1(844)LIGHTCLOUD.

FCC Information:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
Note: This device has been tested and found to comply with the limits for
Class A digital devices pursuant to Part 15A Subpart B, of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential environment. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instruction manual, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to
try and correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
To comply with the FCC's RF exposure limits for general population /
uncontrolled exposure, this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or
transmitter.
CAUTION: Changes or modifications to this equipment not expressly
approved by RAB Lighting may void the user’s authority to operate
this equipment.
Hello
The Lightcloud Controller Mini
is a remotely controlled switch
and 0-10V dimming device.
Product Features
Wireless Control & Configuration
Switching up to 4.2A
0-10V Dimming
Power Monitoring
Patent Pending

LCCONTROL/MINI
Controller Mini
1 (844) LIGHTCLOUD
1 (844) 544-4825
WE’ RE HER E TO HELP:
1 (844) LIGHTCLOUD
© 2022 RAB Lighting, Inc
1 (844) 544-4825
Lightcloud is a commercial
wireless lighting control system.
It’s powerful and flexible,
yet easy to use and install.
Learn more at lightcloud.com
Table of contents
Other Lightcloud Controllers manuals
Popular Controllers manuals by other brands

B&G
B&G ZEUS S Detailed App Guide

Flowserve
Flowserve Logix 510si Installation, operation & maintenance instructions

Mitsubishi Electric
Mitsubishi Electric Q Series user manual

Panasonic
Panasonic FP0H Series user manual

Honeywell
Honeywell Air Alert 96d user manual

Burster
Burster 9251 PROFINET Series Operation manual