LIGHTINC MH-60 User manual

MH-60 LED Beam
User manual
P le a se rea d t he ins t r u ction s ca refu ll ybefore use

2
TABLE OF CONTENTS
1. S af ety I nst r uctions ..................................................................................................... 2
2. Technical Specifications ...........................................................................................5
3. How To Control The Unit ..........................................................................................6
4 .Trouble shooting ........................................................................................................9
5. Fixture Cleaning .......................................................................................................11
statement
The product has well capability and intact packing when leave
factory. All of the user should comply with warning item and manual, any
misuse cause of the damages are not included in our guarantee, and
also can not be responsible for any malfunction & problem owing to
ignore the manual.
1. S af ety I nst r uctions
Please keep this User Guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
 Unpack and check carefully there is no transportation damage before using
the unit.

3
 Before operating, ensure that the voltage and frequency of power
supply match the power requirements of the unit.
 It’s important to ground the yellow/green conductor to earth in order
to avoid electric shock.
 The unit is for indoor use only. Use only in a dry location.
 The unit must be installed in alocation with adequate ventilation, at
least 50cm from adjacent surfaces. Be sure that no ventilation slots are
blocked.
 Disconnect main power before replacement or servicing.
 Make sure there are no flammable materials close to the unit while operating as
it is fire hazard.
 Use safety cable when fixes this unit. DO NOT handle the unit by taking its head
only, but always by taking its base.

Maximum ambient temperature is Ta: 40℃.DO NOT operate it where the
temperature is higher than this Unit surface temperature may reach up to 85℃.
DO NOT touch the housing bare-hand during its operation. Turn off the power
and allow about 15 minutes for the unit to cool down before replacing or serving.
 In the event of serious operating problem, stop using the unit
immediately.Never try to repair the unit by yourself. Repairs carried out by
unskilled people can lead to damage or malfunction. Please contact the
nearest authorized technical assistance center. Always use the same type
spare parts.
 DO NOT touch any wire during operation as high voltage might be causing
electric shock.
Warning:

4
 To prevent or reduce the risk of electrical shock or fire, do not expose the unit to
rain or moisture.
 DO NOT open the unit within five minutes after switching off.
 The housing, the lenses, or the ultraviolet filter must be replaced
if they are visibly damaged.
Caution:
There are no user serviceable parts inside the unit. DO NOT open the housing
or attempt any repairs yourself. In the unlikely event your unit may require
service, please contact your nearest dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that
the unit is firmly fixed to avoid vibration and slipping while operating.
And make sure that the structure to which you are attaching the unit is secure
and is able to support a weight of 10 times of the unit’s weight. Also always use a
safety cable that can hold 12 times of the weight of the unit when installing the
fixture.
The equipment must be fixed by professionals. And it must be fixed at aplace
where is out of the touch of people.

5
2. Technical Specifications
Light Sources: 60w osram led
Beam Angle:4.5°
Power Voltage: AC 100-240V, 50/60Hz
Power consumption :80w
Dimension: 21*15*27cm
Packing: 480*320*440mm (2pcs)
Net Weight: 4Kgs;Gross Weight: 5Kgs
Control
DMX Channel: 11/16Channel
Control Modes: DMX512,auto run,master-slave,music
Pan/Tilt
Pan/Tilt: 540°/ 270°
Pan/Tilt Resolution: 8/16 bit
Construction
Display: Digital Display
Data In/Out socket: 3-pin XLR sockets
Protection Rating: IP20
Features
Dimmer: 0~100% smooth dimming
Variable strobe effects
Fast, quiet operation and flicker free

6
3. How To Control The Unit
Th e D M X512 is w id ely used in intellig ent ligh ti ng co n tr ol,with aDMX 512
controller.connect several lights together,dmx in and dmx out,
3 p in XLR co nn ectors : Pin 1: G ND , Pin 2: Nega tive s ig n a l (-), Pin 3: P o s itive s i gna l
(+)
Display:
MENU To select the programming functions
DOWN To go backward in the selected functions
uP To go forward in the selected functions
ENTER To confirm the selected functions
SetDMX AddressCode
1 Press "Menu" to "Set DMX Address",and press"ENTER" keys to enter into
2Show "Set DMX Address DMX Address:001",Press the "UP and DOWN"
keys to amended
3 Press "ENTER"keys to save and Exit,Press the"MENU"Keys does not save and
Exit

7
Menu
Addr
d001-d512
CHSE
CH-11
Set dmx add
11 CH Mode
CH-16
16 CH Mode
Node
DNH
DMX mode
FAST
Fast speed
SLOU
Slow speed
SOUN
Sound mode
SENS
SE0-SE99
Mic sensitivity
PAN
OFF
Pan forward rotating
ON
Pan inversed rotate
TILT
OFF
Tilt forward rotate
ON
Tilt inversed rotate
BALA
rED
Red color
GrEE
Green color
BLUE
Blue color
WHIL
White color
DEFA
YES
Factory Reset
rEST
YES
Reset

8
DMX channel 11/16 Channels
16 DMX channels mode
CH
Function
Detail
1
Pan
0-255 Value increase,rotate forward; value
decrease,rotate inversed
2
Pan
fine-tuning
0-255 Value increase,rotate forward; value
decrease,rotate inversed
3
Tilt
0-255 Value increase,rotate forward; value
decrease,rotate inversed
4
Tilt fine-tuning
0-255 Value increase,rotate forward; value
decrease,rotate inversed
5
Motor speed
0-255 :pan,Motor working speed
6
Strobe
1-255; Strobe,From slow to fast
7
Dimmer
0-255 :0-100% dimming
8
RDimmer
0-255; 0-100% Red dimming
9
GDimmer
0-255; 0-100% Green dimming
10
BDimmer
0-255; 0-100% Blue dimming
11
WDimmer
0-255; 0-100% White dimming
12
0-10
Enable other channels
11-127
Color changing
128-160
Color jump changing
161-200
Color gradual changing 1
201-255
Color gradual changing 2
13
Built-in effect
speed set
Color jump change,gradual changing,speed
adjust.
14
Built-in effect
0-10,Enable other channels
11-120,Built-in effect fast run
121-244,Built-in effect slow run

9
245-255,Music mode
15
Built-in effect
speed set
Built-in effect speed ajustable
16
Reset
150-200;rest
DMX 11 Channels Mode
CH
Function
Detail
1
Pan
0-255 Value increase,rotate forward; value
decrease,rotate inversed
2
Pan
fine-tuning
0-255 Value increase,rotate forward; value
decrease,rotate inversed
3
Tilt
0-255 Value increase,rotate forward; value
decrease,rotate inversed
4
Tilt fine-tuning
0-255 Value increase,rotate forward; value
decrease,rotate inversed
5
Motor speed
0-255 :Pan,motor working speed
6
Strobe
1-255; Strobe,From slow to fast
7
Dimmer
0-255 :0-100% dimming,from dark to light
8
RDimmer
0-255; 0-100% Red dimming
9
GDimmer
0-255; 0-100% Green dimming
10
BDimmer
0-255; 0-100% Blue dimming
11
WDimmer
0-255; 0-100% White dimming
4. Trouble shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion .He r e a r e

10
s o m e s ug g es tion s fo r ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Ch eck th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a g e on th e m a i n co nn e ct o r .
3. Ch eck th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link
p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess
s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Ch eck if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta g e c a b les th a t
m a y c a us e d a m a g e or in terfer ence to D M X inter face circui t.
C .One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th ePCB is
b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition.

11
5. Fixture Cleaning
Th e clean ing o f inter na l a nd ex ter na l optica l lens es a nd/or m ir r ors m u s t b e c a rr ied
ou t p eriodica lly to optim iz e ligh t ou tput . Cle a nin g f r eq uency d e p end s on t h e
environm ent in w hich t h e f ixture ope r a tes : d a m p , s m oky o r p a r tic ula r ly d ir ty
s urr ound ing c a n c a us e g r eat er acc um ula tio n of d ir t on th e u nit’ soptics .

Cle a n with s oft clo th u s ing no r m a l g l a ss clea ni ng fluid .

A lw a y s d r y th e parts ca r ef ully .

Cle a n th e ex ter na l optic s a t leas t ev ery 20 days. Cle a n th e in ter na l opti cs a t
lea s t ev ery 30/60 days.