ColorKey Mover Wash HEX 12 User manual

Mover Wash HEX 12
RGBAW+UV Moving Head Wash Light
CKU-5039
USER MANUAL

2
Table of Contents
INTRODUCTION ......................................................................................................................................... 3
SERVICE & SUPPORT .............................................................................................................................. 3
DISPLAY OPERATION .............................................................................................................................. 4
MENU GUIDE .............................................................................................................................................. 5
DMX VALUES ............................................................................................................................................. 6
9 CHANNELS MODE ................................................................................................................................. 6
15 CHANNELS MODE ............................................................................................................................... 7
OPERATION ............................................................................................................................................... 8
TROUBLESHOOTING ............................................................................................................................... 9
.................................................................................................................................................................... 10
TECHNICAL INFORMATION .................................................................................................................. 10
Please read these instructions carefully before use. Operating this fixture according
to these instructions is important to avoid any possible damage or accidents caused
by misuse.

3
Introduction
Package Contents
• Mover Wash HEX 12
• Power Cable
• Hanging Brackets
• User Manual
Caution! Opening this unit voids warranty. Contact ColorKey for any service requests.
Warning! To avoid electrical shock, be sure to disconnect power before any service or
when moving or setting up the fixture.
Caution! Avoid direct eye exposure with the fixture when on.
• This fixture is for indoor use only.
• Do not install or operate this fixture near flammable materials.
• This device must be installed, operated, and maintained by a qualified
professional.
• Please check if the voltage is in accordance with the rated power before
installing.
• Do not operate this fixture if the power cord has been damaged. Turn off fixture
and replace with a power cord of similar rating.
Service & Support
Your ColorKey product includes a 2-year warranty. For technical support or to register
your product, please visit https://www.colorkeyled.com/support/
You can also reach us by phone Monday thru Friday, 8:30am – 5pm PST
at [phone].

4
Display Operation
Menu: Access the menu/Scroll through menu options (*Hold Menu for two
seconds to exit the menu and return to your chosen program)
Up: Scroll through menu selections or increase parameters
Down: Scroll through menu selections or parameter decrease
Enter: Open/Select the current menu option

5
Menu Guide
Menu Item
Values
Function
Addr
A001-A512
DMX Address setting
ChNd
9ch / 15ch
Channel selection mode
ShNd
Show0-Show4
Performance modes
SLNd
NASt / SLV1 / SLV2
Master / Slave settings
Soun
No/Yes
Sound active mode
SEnS
0-100
Sound active sensitivity
Blnd
No/Yes
Boot pause mode
Pan
No/Yes
X motor forward / reverse
Tilt
No/Yes
Y motor forward / reverse
LED
No/Yes
Display on / off during use
Disp
Yes / No
Invert the LED display
Bala
R:125-255,B:125-
255,G:125-255
White balance setting- Add or decrease red,
green and blue to create White Balance temp.
Test
Self-performance test. The light will color cycle
pan and tilt on its own
Temp
-20-100C
Temperature of the light will be displayed
Fhrs5
Displays number of hours used
uEr
NA
rESt
Reset light to out of box settings

6
DMX Values
5 Channels Mode
Channel
Value
Function
1
000-007
Off
008-255
Dimmer (0 to 100)
2
000-007
Open
008-037
Random Strobe
038-067
Sound Active Strobe
068-255
Strobe (Rate from slow to fast)
3
000-007
No Function
008-0037
Red
038-067
Green
068-097
Blue
098-127
White
128-157
Orange
158-187
UV
188-247
Color fade (Slow to fast)
248-255
Color chase
4
000-007
No Function
008-037
Pan/Tilt movement 1
038-067
Pan/Tilt movement 2
068-097
Pan/Tilt movement 3
098-127
Pan/Tilt movement 4
128-157
Pan/Tilt movement 5
158-187
Pan/Tilt movement 6
188-217
Pan/Tilt movement 7
218-247
Pan/Tilt movement 8
248-255
Pan/Tilt movement 9
5
000-007
Hold
008-247
Manual speed (Slow to fast)
248-255
Sound Active Response

7
9 Channels Mode
Channel
Value
Function
1
0-255
Pan motor adjustment
2
0-255
Tilt motor adjustment
3
0-199
Dimmer from dark to bright
200-250
Strobe from slow to fast
251-255
All bright
4
0-255
Red
5
0-255
Green
6
0-255
Blue
7
0-255
White
8
0-255
Amber
9
0-255
UV
15 Channels Mode
CH
Value
Function
1
0-255
Pan motor adjustment
2
0-255
Fine pan motor adjustment
3
0-255
Tilt motor adjustment
4
0-255
Fine tilt motor adjustment
5
0-255
Pan & Tilt speed
6
0-255
Dimmer from dark to bright (Ch 14 Must be Open)
7
0-255
Red
8
0-255
Green
9
0-255
Blue
10
0-255
Amber
11
0-255
White
12
0-255
UV
13
008-255
Auto color programs
14
008-131
Strobe from slow to fast
132-139
Open
140-181
Strobe effect 1
182-189
Open
190-231
Strobe effect 2
232-239
Open
240-247
Random flashes
248-255
Open
15
128-255
Sound active (001-127 No function)

8
Operation and Control
Fine tuning your Mover Wash Hex 12 start position
The Mover Wash HEX 12 offers the ability to adjust your starting position should your
lights begin to vary after use due to bumps received during transit or use
• To enter adjustment program, press Menu and hold Enter key for 3 seconds
• Use Up and Down navigation arrows to select Pan or Tilt, pressing enter to make
your selection.
• You may now enter fine adjustments from -127 to 127 for both Pan and Tilt to start
your light in its desired position.
• Press Enter to confirm your selection and Menu to exit adjustments program.
• Your Mover Wash will now start at desired position going forward.
Controlling your Mover Wash HEX 12 using a DMX controller:
• Use a DMX cable to connect your Mover Wash HEX 12 to the DMX in/out sockets
on the bottom of the light.
• Set desired DMX address for your light
Using Master/Slave Mode:
The Master/Slave mode allows a group of Mover Wash HEX 12 units (the slaves) to
duplicate the output of another Mover Wash HEX 12 (the master) without a DMX
controller.
1. Set each of the slaves:
n Go to SLNd in the main menu and press enter.
n Select SL1.
2. Set the master:
n Go to SLNd in the main menu and press enter.
n Select NASt.
• The master (NASt) is the unit that runs your program whether in one of the static
color modes or various Auto programs.

9
Using Slave modes (SL1, SL2) to create a light show
Using 4 or more lights for best effect, Mover Wash HEX can help create auto-light
shows by engaging Auto Programs on the Master fixture and having slaves
connected in varying sequences to display varied yet synchronized light shows.
1. Set each of the desired slaves SL1, SL2:
n Go to SLNd in the main menu and press enter.
n Select SL1.
n Repeat steps for each slave fixture SL1 and SL2
2. Set the master:
n Go to SLNd in the main menu and press enter.
n Select NASt.
• Accessing the (ShNd) programs on the Master light will now create varying displays
of synchronized light on the master and slave fixtures through (Auto) and (SoUn)
functions.
Troubleshooting
Problems
Solutions
No DMX Control
Ensure your DMX controller is sending signal and you are
using a proper and working DMX cable.
Head position is off
centered at startup
See directions on pg. 7 “Fine tuning your Mover Wash
Hex 12 start position”
Master / Slave
For a direct copy of the master (NASt), select SL1. For a
synchronized yet varied Auto Show, select SL2.

10
Technical Information
• 12x12W RGBAW+UV LED Wash Light
• DMX Channel Modes: 9 / 15 channels
• Control modes: DMX 512, Master /Slave, Sound active, Auto programs
• Pan: 540o
• Tilt: 270o
• Power consumption: 160W
• Power supply: AC90-230V; 50-60Hz
• Weight: 6.4lb
• Measurements: 10.25in. x 7.14in. x 6.25in.
Please note: As we continue to work towards improving our products and your
experience as a user, we recommend that you check our website periodically for
updates to user manuals and specifications at www.ColorKeyLED.com or you may
contact us directly at [email protected].