Lightware Modex-Tx User manual

MODEX-TX
MODEX-RX
Modular Extender
family
(MODEX)
Quick Start Guide

Modular Extender family
Quick Start Guide
Section 1. Introduction Page 3 / 15
Table of contents
1. INTRODUCTION...................................................................................................................... 4
1.1. BOX CONTENTS................................................................................................................... 4
1.2. TYPICAL APPLICATIONS ....................................................................................................... 4
2. GENERAL DESCRIPTION...................................................................................................... 5
2.1. FRONT VIEW ....................................................................................................................... 5
2.2. REAR VIEW......................................................................................................................... 6
3. INSTALLATION....................................................................................................................... 6
4. FRONT PANEL OPERATIONS............................................................................................... 7
5. WEB CONTROL –USING THE BUILT-IN WEBSITE ............................................................ 7
5.1. NETWORK STRUCTURE ....................................................................................................... 7
5.2. IP SETTINGS....................................................................................................................... 8
5.3. ESTABLISHING THE CONNECTION ......................................................................................... 8
5.4. BUILT-IN WEB...................................................................................................................... 9
5.4.1. Main menu ................................................................................................................ 9
5.4.2. Crosspoint menu....................................................................................................... 9
5.4.3. EDID menu ............................................................................................................. 14
5.4.1. Settings................................................................................................................... 15
6. WARRANTY .......................................................................................................................... 15
7. DOCUMENT REVISION HISTORY ....................................................................................... 16

Page 4 / 15 Section 1. Introduction
1. Introduction
Thank you for choosing MODEX the Lightware Modular Extender family. The Modex
family is a hybrid, modular and multi-layer group of extenders supporting the AV and
broadcast industry’s formats. It is capable of extending digital and analog audio and
video, USB KVM, Ethernet and control signals like RS-232, RS-422, IR etc....
1.1. Box contents
Quick Start Guide (this document)
MODEX Transmitter or Receiver unit
IEC Power cable
UTP LAN cable
Four rubber foot
Infrared transmitter and receiver pair
5-pole male phoenix connector
1.2. Typical applications

Modular Extender family
Quick Start Guide
Section 2. General description Page 5 / 15
2. General description
Lightware’s hybrid modular multi-layer extenders allow different types of input and output
modules, which gives the maximum flexibility for rental and installation signal
transmissions. The hybrid architecture allows signal transmission between Tx and Rx
extenders even if they have different video connectors. For example a DVI source can be
routed to an HDMI sink, but HDCP encrypted sources cannot be routed to non-HDCP
capable DVI sinks. The modular design allows you to select the required video and
interface module. The multi-layer concept allows every media layer (video, audio, etc.) to
be managed independently of each other.
The MODEX is fully compatible with the 25G hybrid architecture.
2.1. Front view
USB-KVM1: 1x USB-B connector is on the TX side and 2x USB-A connectors are on the RX side.
USB-KVM USB connection to HOST (Computer) on the TX unit and for
two devices (e.g. Keyboard) on the RX unit.
Ethernet Ethernet connection for control and transfer.
Link status LEDs Audio LED lights green when the audio transfer is active. The
video LED indicates the correct video transmission. The CNTRL
LED is green when the low speed handshake of the two
extenders is complete. The OPTS LINK LED lights when the
optical link is active.
Menu display Displays status information and menu operation.
Menu navigation Up, down, left, right, escape and enter buttons for menu
navigation.
Status LEDs CPU live LED blinks to indicate normal operation. +5V led and
+3.3V light green when the extender is powered on.
Reset button You can reboot the extender.

Page 6 / 15 Section 3. Installation
2.2. Rear view
Media connector User-selected physical connector.
Interface modules Two user-selected optional interface modules.
Video & audio module User-selected video and audio module.
3. Installation
Step 1. Connect the transmitter and the receiver by using an LC or Neutrik
OpticalCON connector equipped with multi or single mode fiber cable
depending on the Media connector.
Step 2. Connect a DVI or HDMI source (e.g. computer) to the transmitter's HDMI
INPUT or DVI INPUT connector.
Step 3. Connect the HDMI or DVI sink (e.g. monitor, projector etc.) to the receiver's
HDMI output. For DVI displays the usage of adaptor cable is necessary.
Step 4. For controlling the device using the built in WEB page connect a computer
with a LAN patch cable to the Ethernet port of the transmitter or the receiver.
Both devices can be accessed and controlled through either Ethernet port.
Step 5. Optionally for Ethernet extension:
connect some Ethernet devices (e.g. switch, laptop, computer etc.)
to the transmitter and to the receiver. All connected devices will
work as if they are connected to the same network.
Step 6. Optionally for RS-232* extension:
Connect a controller unit (e.g. Touch panel) to the RS-232 on TX
with a null modem serial cable,
Connect a controlled device (e.g. Projector) to the RS-232 on RX
with a regular serial cable.
Step 7. Optionally for Infra-Red* extension:
Connect the supplied IR emitter to the IR OUT on TX or RX
Connect the supplied IR detector to the IR IN on TX or RX
Step 8. Optionally for USB HID* extension:
Connect at least one USB HID* device to the receiver. Use the
keyboard and the mouse labeled USB-A connectors.
Connect the transmitter to the computer via the USB-B cable.
Step 9. Power on the devices using the standard IEC power cable
* Mentioned devices are examples and can be connected to either TX or RX.

Modular Extender family
Quick Start Guide
Section 4. Front panel operations Page 7 / 15
4. Front panel operations
Using the front panel LCD menu navigation buttons some basic configuration parameter
can be set and some status information can be displayed.
Menu structure:
Info
MCU Firmware
FPGA Firmware
WEB Content
Supply A
Supply B
Temperature
Settings
Network settings
IP address
Subnet mask
Static gateway
Port number
DHCP
System
Reset
Enter bootload
Factory default
Modules
MODEX frame and core
Info
Product code
Schematic
PCB
Serial Number
MAC address
Settings
MODEX video & audio module*
Info
Product code
Schematic
PCB
Serial Number
Settings
MODEX physical module
Info
Product code
Schematic
PCB
Serial Number
Settings
MODEX interface module*
Info
Product code
Schematic
PCB
Serial Number
Settings
Crosspoints
Video
Audio
USB K&M
Port1
Manufacturer
Product
Serial
VID
PID
Host info
Port2
Manufacturer
Product
Serial
VID
PID
Host info
EDID
Presets
Load preset
Save preset
* A Modex might have more than one video or interface module of the same kind. The
appropriate number of branches of the tree appears in this case.
5. Web control – Using the Built-in website
Modex transceivers have several configuration options. More settings are available using
the built-in website than on the front panel. You can access the website through any
Ethernet connector of the Modex.
5.1. Network Structure
MODEX extenders have a front panel Ethernet port. Additional rear-side Ethernet
connectors are available as interface modules. All of the connectors and the controller
entity belong to the same network inside the Modex. Ethernet link is also transferred to
the connected pair via physical layer link (optical or twisted pair). Connect any RJ45
connector of the TX or the RX to a LAN and you can control both units. Do not connect
more than one port of the Modex pair to the same LAN to avoid loops.

Page 8 / 15 Section 5. Web control –Using the Built-in website
5.2. IP settings
Before you connect to a MODEX extender using a Web browser the IP address must be
set. The Ethernet port can be configured on the front panel LCD menu or remotely
through the built-in website. There are three different ways to configure the IP address.
Set the factory default IP address
MODEX extenders have static IP settings at the first startup. You can reload these
settings to the default state by setting the factory default on the LCD menu (Settings/
System/ Factory Default) or on the built-in website (Settings/ Network).
Transmitter: IP address: 192.168.0.101
port number: 6107
subnet mask: 255.255.255.0
gateway: 192.168.0.1
HTTP port: 80
WEB socket: 81
Receiver: IP address: 192.168.0.102
port number: 6107
subnet mask: 255.255.255.0
gateway: 192.168.0.1
HTTP port: 80
WEB socket: 81
Set a user defined static IP address
The IP address, Subnet mask, Static gateway and the Port number can be set by a user
defined value on the front panel LCD menu (Settings/ Network Settings) or remotely
through the built-in website (Settings/Network).
Set a dinamic IP address
DHCP mode can be enabled on the front panel LCD menu (Settings/ Network Settings/
DHCP) or remotely through the built-in website (Settings/Network/DHCP). The extenders
acquire IP addresses from the DHCP server on the LAN in this case.
5.3. Establishing the connection
To connect to a Modex launch a web browser and type the IP address. You can verify the
actual address of the Modex unit on its front panel display (Settings/Network). See
previous chapter for available options.

Modular Extender family
Quick Start Guide
Section 5. Web control –Using the Built-in website Page 9 / 15
System requirements
Operating System: Microsoft Windows XP, Windows Vista, Windows 7, Mac OS X, or
Linux
Web Browser: Mozilla Firefox, Apple Safari (Microsoft Internet Explorer is not supported)
5.4. Built-in web
5.4.1. Main menu
After the connection is established to any of the devices the main menu appears by
default. A status window indicates which device has been connected to. This is the local
device. In this window the remote device can be selected. Both devices must be
configured for appropriate transfer. The main menu contains three major sub
configuration menus: the Crosspoint, the EDID and the Settings.
5.4.2. Crosspoint menu
The MODEX is a multi-layer extender and every layer has an own specific control panel
for configuration.
Left click on the Crosspoint label in the main menu to obtain layers of configuration
panel supported by the selected Modex extender pair.
Note: USB KVM has no crosspoint configuration panel
Note: If a layer is not supported by the selected MODEX then there is no label for
its properties
5.4.2.1. Video crosspoint
In the main menu left click on the Crosspoint label then left click on Video label the
video crosspoint appears. The inputs are at the top row and the outputs are at the right
column. The number of the inputs and the outputs are depending on the number and the
direction of the video modules. As MODEX supports only one video transmission over the
link the link appears as an input or as an output depending on the direction of the
extender.
At the transmitter side the link
appears as an output. At the
receiver side the link appears as
an input.
The input and output settings can be accessed through
module and port properties. Every port is represented with a
connector icon, while the modules are represented with a
colored bar. Some modules have multiple ports so the
module settings may affect which ports can be used.

Page 10 / 15 Section 5. Web control –Using the Built-in website
Module property
Each MODEX modules including video modules, interface modules and physical link
modules have their special property list. The color of the Module property bar indicates
the related ports. Different color means different module. Left click on the Module
property bar to open he module property window.
In the property window there is some general information about the selected video or
physical module
and there is a
settings parameter
list. Under settings
there is a Mode
function. Some
video modules have
two or more video
inputs or outputs,
but only one of
these inputs or
outputs can be used
in the video
crosspoint. This is
because only one
video stream
transmission is
permitted between
the core module
and the video
module. After setting the mode of the video interface module the supported input or
output port of the selected mode appears in the video crosspoint and the port property
becomes available.
Port property
Left click on the Port property icon to open the
property window. The physical port, the input and
the output ports have different property windows.
The property window displays status information
about the port and signal information about the
incoming and outgoing signals. At the same time
gives opportunity to set parameters for example
rename a port or reach special functions for
example Frame detector at the input port side.

Modular Extender family
Quick Start Guide
Section 5. Web control –Using the Built-in website Page 11 / 15
5.4.2.2. Audio crosspoint
In the main menu left click on the Crosspoint label then left click on Audio label the
audio crosspoint appears. The inputs are at the top row and the outputs are at the right
column. The number of the inputs and the outputs depends on the number, the direction
and the mode settings of the audio modules.
OPTx extenders support two audio groups the
Main audio group and the S/Pdif audio
group. These groups are independent from
each other. In this case there are forbidden
crosspoint connections.
The link can support four audio layers. The
Embedded audio (from Tx to Rx) and the
Return AUX (from Rx to Tx) belongs to the
Main audio group. The Forward Audio (from Tx to Rx) and Return Audio (from Rx to
Tx) belongs to the S/PDIF audio group.
At the transmitter
side the Embedded
audio and the
Forward Audio
appears as an
output, the Return
Audio and the
Return AUX
appears as an
input. At the
receiver side the
direction is the
opposite.
The input and output settings can be accessed through module and port properties.
Every port is represented with a connector icon, while the modules are represented with a
colored bar. Some modules have multiple ports so the module settings may affect which
ports can be used. Ports settings can be accessed through the Port property icon. The
module settings can be accessed through the Module property bar.