Lightware PSU2x10-200-12V User manual

Quick Start Guide
PSU2x10-200-12V
PSU2x10-200-5V
PSU2x20-400-12V
PSU2x20-400-5V
Lightware Visual Engineering PLC.
Budapest, Hungary
[email protected] [phone]
[email protected] [phone]
©2023 Lightware Visual Engineering. All rights reserved. All trademarks mentioned are the
property of their respective owners. Specications are subject to change without notice.
Further information on the device is available at www.lightware.com.
Doc. ver.: 1.5
19210073
TAKE CARE OF ME
I AM THE ONE AND ONLY
USER DOCUMENT FOR
THIS PRODUCT
Introduction
Thank you for choosing Lightware’s rack mountable power supply. The units are all housed in
a 1U high solid metal rack enclosure for durability and easier mounting. 5V and 12V DC output
versions are also available with 10 and 20 output connectors. Several protections are built in
like short circuit, overload, over voltage, over temperature which features make these PSUs
really trustful. The units are designed to supply devices made by Lightware.
 The cover picture of this document is an illustration. The PSU2x series devices are built with
2 pcs rack ears on the front side by default.
Box Contents
 Please note that DC-DC power cables are not supplied with the product.
Power supply unit with
rack ears (2x)
IEC power cable Safety and Warranty Info,
Quick Start Guide
Safety and
Warranty
Info
Quick
Start
Guide
Specications
General
Compliance....................................................................................................CE, UKCA
Electrical safety.................................................................................. EN 62368-1:2014
EMC compliance (emission)..................................................................EN 55032:2015
EMC compliance (immunity) .................................................................EN 55035:2017
RoHS compliance..................................................................................EN 63000:2018
Warranty ............................................................................................................. 3 years
Operating temperature ...................................................... 0 to +55°C (+32 to +122°F)
Operating humidity ......................................................... 10% to 90%, non-condensing
Cooling.............................Fan (2 pcs., 40 mm diam.), air ows right to left (front view)
Protection against.............. Short circuit / Overload / Over voltage / Over temperature
Connectors
AC power connector....................................................................... IEC C14 receptacle
DC power connector (5V version)........................... locking DC connector, 2.5/5.5 mm
DC power connector (12V version)......................... locking DC connector, 2.1/5.5 mm
Power
Power supply option ....................................................................................built-in PSU
Supported power source .........................................................100-240 V AC; 50/60 Hz
AC fuse ...................................................................................................................F 5 A
Enclosure
Rack mountable......................................................................................... Yes, 1U high
Enclosure material........................................................................................ 1 mm steel
Dimensions in mm........................................................... 482* (446)W x 182D x 43.9H
Dimensions in inch .............................................................. 19* (17.6)W x 7.2D x 1.8H
Net Weight (PSU2x10-200 series).......................................................2870 g / product
Net Weight (PSU2x20-400 series).......................................................3430 g / product
* with rack ears
Models PSU2x10-
200-5V
PSU2x20-
400-5V
PSU2x10-
200-12V
PSU2x20-
400-12V
DC output number 10 20 10 20
Nominal power 200 W 400 W 200 W 400 W
DC output voltage 5V 12V
Rated current per
output port 2.5A 1.1A
Heat dissipation
(max.) 683 1365 683 1365
 The main differences among the variants are the number of the DC connectors and the
voltage range; PSUx20-400-12V can be seen on the photos.
Front and Rear View
1
Power LED Power LED lights green when the unit is powered on.
2
AC connector Standard IEC power connector. Accepts 100 to 240 Volts,
50 or 60 Hz power sources.
3
Power switch The power supply can be switched ON/OFF with this switch.
4
DC connectors Locking DC connectors for the appliances that are desired
to supply.
Compatibility
The following table contains those Lightware products that are compatible with the power
supplies and also the technical data of the DC plug:
PSU2x10-200-5V, PSU2x20-400-5V
DC plug Compatible Lightware products
Power supply Device Type
2.5 / 5.5 mm
1.35 / 3.5 mm DVI-OPT-110 series
DP-OPT 150 series
USB Micro-B DVI-HDCP-OPTS 90 series
DVI-HDCP-OPTM 90 series
2.5 / 5.5 mm
EDID Manager V4
HDMI-, DVISL- and DVIDL extenders
DA2DVI-HDCP-Pro
DA2DVI-DL
DA2HDMI 4K-Plus series
DP-OPT 100 series
DVI-TP series
HDMI-, UMX- and DVIDL-OPT series
HDMI 4K series
SW4-OPT-TX240RAK
Remote control panels
PSU2x10-200-12V, PSU2x20-400-12V
DC plug Compatible Lightware products
Power supply Device Type
2.1 / 5.5 mm 2.1 / 5.5 mm
DP-TPS-200 series
DVI-HDCP-TP-50 and -100 series
DVI-HDCP-TPS-90 and -210 series
HDMI-TPS-TX-200 series
HDMI-TPS-90-95-97 series
HDMI-TPS-RX110AY
HDMI-TP-50, -100 and -200 series
UMX-TP series
UMX-TPS-TX100 series
TPS-TX200 series
MMX4x2-HT200
MMX4x2-HDMI
SW4-TPS-TX240
 Cables are available at Lightware, please contact [email protected].
Connecting Devices
1. Place the power supply unit in the rack and x it by screws with the mounting ears.
2. Connect the DC cables to the power supply and to the extender units.
3. Connect the AC power cable to the power supply.
4. Switch on the appliance.
 Please note that xing screws and DC power cables are not supplied with the appliance.
 If the power supply cannot be switched on, please check the IEC power cable, the AC
mains and the fuse at the AC connector on the back of the unit. If the LED on the front panel
does not light up at all, the unit is most likely damaged and further use is not advised. Please
contact [email protected].
Locking DC Connectors
DC cables from Lightware contain locking DC connector that establishes robust and safe
power connection. After plugging it in, turn the plug clockwise as shown on the picture:
 Do not forget to turn the plug counterclockwise before trying to disconnect the cable.
Assembly of the Rack Ears
Two rack ears are supplied with the product, which are xed on the left and right side with 8 pcs
M4 screws. The ears are removable and can be re-assembled to another position or direction.
 M4x8 size is the longest allowed screw for xing the ears to the housing. Using
different (e.g. longer) screws may cause damage to the device.
Mounting with Rack Ears
The rack ears allow mounting the device as a standard rack unit installation.
 Always use all the four screws for xing the
device ears to the rack rail. Choose properly
sized screws for mounting. Keep a minimum of
two threads left after the nut screw.
Ventilation
 To ensure the correct ventilation and avoid
overheating, leave enough free space around the
appliance. Do not cover the appliance, leave the
ventilation holes free on both sides.
min. 2
threads left
rack rail
device
mounting ear
rack screw
flat washer
cage nut
1A DC PIN: 2mm 1A DC PIN: 2mm
2 3 4
1

Mechanical Drawings
The PSU2x20-400-12V model can be seen in the pictures, but the dimensions are the same for both models. Dimensions are in mm.
Front View (1:3)
Rear View (1:3)
Top View (1:3)
Class I Apparatus Construction
This equipment must be used with a mains power system with a protective earth connection.
The third (earth) pin is a safety feature, do not bypass or disable it. The equipment should be
operated only from the power source indicated on the product.
To disconnect the equipment safely from power, remove the power cord from the rear of the
equipment or from the power source. The mains plug is used as the disconnect device, the
disconnect device shall remain readily operable. There are no user-serviceable parts inside of
the unit. Removal of the cover will expose dangerous voltages. To avoid personal injury, do not
remove the cover. Do not operate the unit without the cover installed.
The appliance must be safely connected to multimedia systems. Follow instructions described
in this manual.
Replacing the AC Fuse
Unplug the AC power cord from the device. Locate the AC fuse on the rear panel. Replace only
the AC fuse as indicated on the rear panel. Connect the power cord to the device and to the
AC power source. Make sure the device is working properly.
Ventilation
For the correct ventilation and to avoid overheating, ensure enough free space around the
appliance. Do not cover the appliance, leave the ventilation holes free and never block or
bypass the ventilators (if there are any).
WARNING
To prevent injury, the apparatus is recommended to be securely attached to the oor/wall or
mounted in accordance with the installation instructions. The apparatus shall not be exposed
to dripping or splashing, and no objects lled with liquids, such as vases, shall be placed on the
apparatus. No naked ame sources, such as lit candles, should be placed on the apparatus.
WEEE ( Waste Electrical & Electronic Equipment )
Correct Disposal of This Product
This marking shown on the product or its literature indicates that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate this
from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product or their
local government ofce for details of where and how they can take this item for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for
disposal.
Schematic of PSUx10-200-5V and PSUx-10-200-12V Schematic of PSUx20-400-5V and PSUx-20-400-12V
 If any of the DC connectors gets faulty, the other DC connectors will be usable
due to the design of the appliance. Do not use the faulted connector, please contact
[email protected].
Side View (1:1)
CA I N
IS
C IC S C
D N P N
A
IS D C C
C I N
PAS I
Sn:
AC
A
A
1A DC PIN: 2mm 1A DC PIN: 2mm
Important Safety Instructions
Please read and keep the information in the attached safety instructions supplied with the
product before starting to use the device.
Safety Symbols Legend
Symbol Description
Alternating current
/
On (Power) / Off (Power)

Caution, possibility of electric shock
Caution
CAUTION AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR 
AC mains
10x DC connectors 10x DC connectors
Power supply
Power supply
Power
switch
AC connector
AC mains
10x DC connectors
Power supply
Power
switch
AC connector
43.9
446
482
POWER
PP
M4 thread
14.4
14.3514.35 15.2
15.2
182