LightwaveRF Connect Series User manual

Connect Series
www.lightwaverf.house
Dusk to Dawn Sensor
Model No. LW801
Instruction Manual
Version 2.1

EC DECLARATION OF CONFORMITY
Responsible Authority:
LightwaveRF PLC,
Innovation Campus Birmingham
Faraday Wharf
Holt Street
Birmingham
B7 4BB
Tel: [phone]
Email: [email protected]
Model Number(s): JSJSLW801
Description: Dawn to Dusk Sensor
Directives this equipment
Complies with: 2006/95/EC The Low Voltage Directive N/A
2004/108/EEC The Electromagnetic Compatibility Directive
1999/5/EC R&TTE Directive
93/68/EEC CE Marking Directive
Standards Applied in order to verify compliance
Safety: BS EN 60730-1: 2011
Health:
R&TTE: EN 301 489-1 V1.9.2: (2011-09), EN 301 489-3 V1.4.1: (2002-08)
EN 300 220-1 V2.1.1: 2006, EN 300 220-2 V2.1.2: 2007
EMC: EN 301 489-1 V1.9.2: (2011-09), EN 301 489-3 V1.4.1: (2002-08),
EN 55022: 2010, EN 61000-3-2: 2006 +A1: 2009 +A2: 2009 Class A,
EN 61000-3-3: 2008, EN61000-4-2: 2009,
EN 61000-4-3: 2006 +A1: 2008 +A2: 2010, EN 61000-4-4: 2012,
EN 61000-4-5: 2006, EN 61000-4-6: 2009, EN 61000-4-11: 2004
For and on behalf of LightwaveRF PLC
----------------------------------------
Name J Shermer
Position Managing Director

How does it work?
How do I get started?
Please refer to the following instructions that will
guide you through the setup of a LightwaveRF
Dusk to Dawn Sensor. Once successfully setup,
the Sensor will automatically switch on and o
LightwaveRF devices at dusk or dawn.
The Dusk to Dawn Sensor is a wireless and
portable sensor and should be positioned in a
place suitable to measure the ambient light level.
As it is waterproof, It can be positioned outdoors,
although it must be within the 15m range of the
LightwaveRF devices intended to be switched.
Help video & further guidance
For additional guidance, and to watch a video
that will help guide you through the installation
process, please visit the support section on
www.lightwaverf.com
Get Started

IMPORTANT: Please retain these instructions for guidance on how to link
the sensor to other LightwaveRF devices. For additional guidance please
visit the support section on www.lightwaverf.com
Main indicator
LED
Waterproof
housing
Overview
Front
Installation

Time delay
switch
Battery
compartment
Cover
mounting
screw hole
Start button
(activate sensor and
set light level)
Back
(cover removed)
Linking button
Waterproof seal
Installation

Removing the back cover
In order to setup the Dusk to
Dawn Sensor, and to insert or
replace the batteries, the back
cover must first be removed.
1. Gently unhook the rear stand
using a flathead screwdriver as
shown.
2. Unscrew the back cover using a
suitable screwdriver.
NOTE: When reassembling, it is
important that the back cover is
screwed on securely in order to
retain the waterproof quality of
the sensor housing.
Installation

Linking the sensor to a
LightwaveRF device
1. Place the LightwaveRF device that
you wish to control (e.g. Dimmer) in
‘linking’ mode. For information on how
to do this please refer to the
instruction manual for that specific
LightwaveRF device.
Inserting the Batteries
The battery compartment is accessed
from the rear of the switch beneath
the cover. 2 x AAA batteries are
required (not included). Once fresh
batteries have been inserted, the start
button must be pressed to
(re)activate the sensor.
NOTE: When the batteries are low, the
Sensor light will flash every 3 seconds.
Device setup

2. Whilst the LightwaveRF device is in
linking mode, switch the ‘learn’ slider
on the sensor to the ‘del’ or ‘set’
position (either is ok). This action will
send out a command instructing the
sensor to link to the device. Repeat
this step to link to as many
LightwaveRF devices as desired.
3. The LED on the LightwaveRF
device receiving the linking command
should flash to indicate that the linking
attempt has been successful.
Unlinking the sensor from a
LightwaveRF device
1. Place the LightwaveRF device that
you wish to remove in ‘linking’ mode.
For information on how to do this
please refer to the instruction manual
for that specific LightwaveRF device.
Device setup

Setting the light level
IMPORTANT: To promote reliable operation, try to ensure that the Dusk to
Dawn Sensor is positioned where it will not be aected directly by bright,
artificial lights that will interfere with the sensor.
Setting the light level alters the preset at which the sensor will automatically
turns on/o LightwaveRF devices. The level can be set by pressing the
‘start’ button which activates the sensor. There are two methods:
2. Whilst the device is in linking
mode, switch the ‘learn’ slider on
the sensor to the ‘set’ or ‘del’
position (either is fine). This action
will send out a command to unlink
the LightwaveRF device.
3. The LED on the LightwaveRF
device receiving the command
should flash to indicate that the
unlinking attempt has been
successful.
Device setup

Setting the time delay
The time delay function consists of
a rotary switch with preset hour
marks. If the switch is set to ‘0’,
then there is no time delay set. The
sensor will turn on/o any
LightwaveRF device once the light
level has gone below/above that
setup by the user.
2. Hold the ‘start’ button for 3
seconds (sensor light will flash for
several seconds). This will instruct
the sensor to learn the current light
level in its immediate environment
and use this level to trigger devices.
1. Press and release the ‘start’
button. This will instruct the sensor
to send out an on or o command
when light levels reach the factory
preset (10 lux).
Device setup

Specification
RF frequency: 433.92 MHz
Input rating: 1.5V (2 x AAA Batteries)
Range: 15m (indoors)
Warranty: 2 year standard warranty
IP56 Approved.
If the delay switch is set to one of the
hour marks, then the linked
LightwaveRF device will still be
turned on at the preset light level;
however, once the specified amount
of time has elapsed, the Sensor will
automatically send an ‘o’
command, and the receiver will turn
o.
NOTE: If the RF range between the transmitter and receiver is too great to
achieve reliable operation, the LightwaveRF Connect Signal Booster may be
used in conjunction with this product to increase the signal strength over
greater distances.
Device setup & Specification

Version 2.1
2 Quadrant Park
Mundells
Welwyn Garden City
Herts
AL7 1FS
01707 386035
www.lightwaverf.house