LightwaveRF JSJS LW107 User manual

PIR
Operation Manual
Model No: JSJS LW107
OVERVIEW:
connect
LightwaveRF
IMPORTANT: PLEASE RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE. FOR HELP AND SETUP
GUIDANCE PLEASE VISIT www.lightwaverf.com
It is important to install this product in accordance
with the tting instructions below. Failure to do so
may render your guarantee void.

INSTALLATION & SETUP
1. Carefully remove the frame by inserting a at head
screwdriver into the slots and lift away from the unit.

2. Stick double-sided tape onto the back of the
base to stick on the wall, or alternatively the base
may be screwed to the wall (double-sided tape and
screws are included). If using the tape, ensure that
the switches on the reverse are not obstructed.
3. Install batteries, (x 2 AAA 1.5V Alkaline, not
included). To do this, remove the frame and pull o
the back cover.
4. Replace the plate – a‘click’ sound should be
heard to signify that the plate has been correctly
replaced.

Detection Angle
1. Vertically, the maximum detection angle is 65
degrees.
2. Horizontally, the maximum detection angle is 80
degrees without lens-cover and 20 degrees with the
lens-cover (uncut).
Lens Cover
The use of the lens-cover is optional.
t8JUIBGVMMMFOTDPWFSUIFNBYJNVNEFUFDUJPO
angle is 20 degrees.
t5IFMFOTDPWFSNBZCFDVUUPBMUFSUIFEFUFDUJPO
angle (the narrower lens-cover, the wider detecting
angle).

t"MUFSOBUJWFMZUIFMFOTDPWFSNBZCFDPNQMFUFMZ
removed to give a maximum detection angle of 80
degrees.
Function of Switches
1"*3*/(48*5$)
1. Set the motion detector to ‘1/0’ or ‘1’ mode and
position near to the receiver with which it will be
paired.
2. Press the learning button on the receiver. The LED
will ash.

3. Slide the pairing switch from either from ‘1/0’ to ‘1’
or ‘1’ to ‘1/0’, the PIR will then the send the RF code to
the receiver.
4. If the receiver is linked to a lamp the lamp will ash
twice to conrm that the PIR is paired. The receiver
LED will stop ashing.
t*GUIFTXJUDIJTNPWFEUPQPTJUJPOAEVSJOHQBJSJOH
(see below for pairing instructions) then the ‘ON’ code
will be transmitted to paired devices when the PIR is
triggered, and an ‘OFF’ command sent after the set
delay period (see below).
t4XJUDIJOHGSPNAUPQPTJUJPOEVSJOHQBJSJOHXJMM
cause the PIR to send the ‘ON’ code when triggered
but NOT the following‘OFF’ command, therefore the
receiver (e.g. lamp) will remain ON until manually
turned o.
%&-":0''5*.&48*5$)
t5IFTXJUDIIBTQPTJUJPOTTFDNJONJONJO
t&BDITFMFDUJPOSFGFSTUPUIFEFMBZQFSJPEBGUFSUIF1*3
is initially triggered and the ‘ON’ command is sent,
before which the ‘OFF’ command is then transmitted.
-694&55*/(48*5$)
t5IFTXJUDIIBTQPTJUJPOT).-
t*OQPTJUJPOA)UIFA%&-":0''5*.&TXJUDIJTEJTBCMFE
(when working with a door chime receiver, set the PIR
in H mode).

t*OQPTJUJPOA.UIF1*3XJMMCFDPNFBDUJWFXIFO
daylight levels fall under 20 +/-5 lux. (about late
afternoon levels)
t*OQPTJUJPOA-UIF1*3XJMMCFDPNFBDUJWFXIFO
daylight levels fall under 10 +/-5 lux. (about late
evening levels)
NOTE:8IFODIBOHJOHUIF-69TFUUJOHJUNBZUBLFVQ
to 30 seconds for the PIR to adjust.
Battery Low Indicator
The Battery low indicator is positioned inside the
sensor lens. If the battery is low, the indicator will blink
after the set delay period ends to inform that the
batteries need changing.

Birmingham Science Park Aston
'BSBEBZ8IBSG
Holt Street
Birmingham
B7 4BB
5FM
&NBJMTVQQPSU!KTKTEFTJHOTDPN
SPECIFICATION
3'GSFRVFODZ.)[
%FMBZPò5JNFTFDNJONJONJO
"OHMFPGEFUFDUJPO
Vertical- max. 65 degree
Horizontal- max. 80 degree without lens-cover ~ 20
degree with lens-cover uncut.
2x 1.5V AA Alkaline battery not included
Adhesive tape x 2pcs included
Screws x 2pcs (direct screwing onto the wall) included

*www.mr-resistor.co.uk/item.aspx?i=10031
LightwaveRF dimmer switches use trailing edge technology.
Lighting Compatibility Information
If you are going to use LightwaveRF equipment in your house, please read the
information below to ensure you will get the most out of your hardware.
Loading
Our one and two gang dimmers can handle a maximum of 250W of load on each gang of
the switch. The three and four gang switches have a maximum load of 210W on each gang.
If you exceed this load, the switches may overheat and cease to work correctly.
Each gang requires a minimum load to function. This is generally 40w but can be lower with
some lamps. This is generally the case with LEDs where a load of 14W can be enough to
have the switch operating.
Bulbs
LightwaveRF switches can be used with standard incandescent bulbs, halogen bulbs
(including low energy halogens) and dimmable LED bulbs (see below).
Fluorescent tube lighting, including CFL bulbs cannot be used with LightwaveRF equipment.
This includes the LightwaveRF CFR bulb.
LEDs
As there is no standard set for LEDs at present, we cannot state that every dimmable LED
will work with LightwaveRF equipment. Even if exceeding the minimum load, certain LEDs
will not function on their own. In these situations wiring a dummy load* in parallel across
the circuit will correct the issue.
The following LEDs have been tested and do work when at least 2 lamps are in a circuit:
•AuraLED AL-GU10 PRO 5W
•AuraLED AU-GU10 5x1W
•Auralux AU-5W LED Globe 5x1W
•IstoriaLED G9 DL Flood
•IstoriaLED G9 WW Flood
•TCP Dimmable Energy Saver LED 5W
•Truelux 230-5W-DIM
•Toshiba LDRC0627MU1EUD 6.5W 270lm LED
Please check www.lightwaverf.com for up-to-date information on compatibility.